The quirk entry for Focusrite Saffire 6 had no proper ep_idx for the
capture endpoint, and this confused the driver, resulting in the
broken sound. This patch adds the missing ep_idx in the entry.
While we are at it, a couple of other entries (for Digidesign MBox and
MOTU MicroBook II) seem to have the same problem, and those are
covered as well.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220521065325.426-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maris reported that TEAC UD-501 (0644:8043) doesn't work with the
typical "clock source 41 is not valid, cannot use" errors on the
recent kernels. The currently known workaround so far is to restore
(partially) what we've done unconditionally at the clock setup;
namely, re-setup the USB interface immediately after the clock is
changed. This patch re-introduces the behavior conditionally for TEAC
devices.
Further notes:
- The USB interface shall be set later in
snd_usb_endpoint_configure(), but this seems to be too late.
- Even calling usb_set_interface() right after
sne_usb_init_sample_rate() doesn't help; so this must be related
with the clock validation, too.
- The device may still spew the "clock source 41 is not valid" error
at the first clock setup. This seems happening at the very first
try of clock setup, but it disappears at later attempts.
The error is likely harmless because the driver retries the clock
setup (such an error is more or less expected on some devices).
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-and-tested-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220521064627.29292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix following coccicheck error:
./sound/usb/endpoint.c:1671:8-10: ERROR: reference preceded by free on line 1671.
Here should be 'cp' rather than 'ip'.
Fixes: c11117b634 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20220518021617.10114-1-wanjiabing@vivo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Link: https://lore.kernel.org/r/20220516104807.16482-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At cleaning up and moving the device rename from the quirk table to
its own table, we removed the entry for Rane SL-1 as we thought it's
only for renaming. It turned out, however, that the quirk is required
for matching with the device that declares itself as no standard
audio but only as vendor-specific.
Restore the quirk entry for Rane SL-1 to fix the regression.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215887
Fixes: 5436f59bc5 ("ALSA: usb-audio: Move device rename and profile quirks to an internal table")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220516103112.12950-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device doesn't support reading the sample rate, so we need to apply
this quirk to avoid a 15-second delay waiting for three timeouts.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Link: https://lore.kernel.org/r/20220504002444.114011-2-cyrozap@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Jaroslav Kysela <perex@perex.cz>
CC: Takashi Iwai <tiwai@suse.com>
CC: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For making easier to test, add the new quirk_flags bits 17 and 18 to
enable and disable the generic implicit feedback mode. The bit 17 is
equivalent with implicit_fb=1 option, applying the generic implicit
feedback sync mode. OTOH, the bit 18 disables the implicit fb mode
forcibly.
Link: https://lore.kernel.org/r/20220421064101.12456-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a rawmidi output stream is closed, it calls the drain at first,
then does trigger-off only when the drain returns -ERESTARTSYS as a
fallback. It implies that each driver should turn off the stream
properly after the drain. Meanwhile, USB-audio MIDI interface didn't
change the port->active flag after the drain. This may leave the
output work picking up the port that is closed right now, which
eventually leads to a use-after-free for the already released rawmidi
object.
This patch fixes the bug by properly clearing the port->active flag
after the output drain.
Reported-by: syzbot+70e777a39907d6d5fd0a@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000011555605dceaff03@google.com
Link: https://lore.kernel.org/r/20220420130247.22062-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB audio device 0db0:a073 based on the Realtek ALC4080 chipset
exposes all playback volume controls as "PCM". This makes
distinguishing the individual functions hard.
The mapping already adopted for device 0db0:419c based on the same
chipset fixes the issue, apply it for this device too.
Signed-off-by: Maurizio Avogadro <mavoga@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yl1ykPaGgsFf3SnW@ryzen
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the previous fix, we increased the max buffer bytes from 1MB to 4MB
so that we can use bigger buffers for the modern HiFi devices with
higher rates, more channels and wider formats. OTOH, extending this
has a concern that too big buffer is allowed for the lower rates, less
channels and narrower formats; when an application tries to allocate
as big buffer as possible, it'll lead to unexpectedly too huge size.
Also, we had a problem about the inconsistent max buffer and period
bytes for the implicit feedback mode when both streams have different
channels. This was fixed by the (relatively complex) patch to reduce
the max buffer and period bytes accordingly.
This is an alternative fix for those, a patch to kill two birds with
one stone (*): instead of increasing the max buffer bytes blindly and
applying the reduction per channels, we simply use the hw constraints
for the buffer and period "time". Meanwhile the max buffer and period
bytes are set unlimited instead.
Since the inconsistency of buffer (and period) bytes comes from the
difference of the channels in the tied streams, as long as we care
only about the buffer (and period) time, it doesn't matter; the buffer
time is same for different channels, although we still allow higher
buffer size. Similarly, this will allow more buffer bytes for HiFi
devices while it also keeps the reasonable size for the legacy
devices, too.
As of this patch, the max period and buffer time are set to 1 and 2
seconds, which should be large enough for all possible use cases.
(*) No animals were harmed in the making of this patch.
Fixes: 98c27add5d ("ALSA: usb-audio: Cap upper limits of buffer/period bytes for implicit fb")
Fixes: fee2ec8cce ("ALSA: usb-audio: Increase max buffer size")
Link: https://lore.kernel.org/r/20220412130740.18933-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current limit of max buffer size 1MB seems too small for modern
devices with lots of channels and high sample rates.
Let's make bigger, 4MB.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220407212740.17920-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the implicit feedback mode, some parameters are tied between both
playback and capture streams. One of the tied parameters is the
period size, and this can be a problem if the device has different
number of channels to both streams. Assume that an application opens
a playback stream that has an implicit feedback from a capture stream,
and it allocates up to the max period and buffer size as much as
possible. When the capture device supports only more channels than
the playback, the minimum period and buffer sizes become larger than
the sizes the playback stream took. That is, the minimum size will be
over the max size the driver limits, and PCM core sees as if no
available configuration is found, returning -EINVAL mercilessly.
For avoiding this problem, we have to look through the counter part of
audioformat list for each sync ep, and checks the channels. If more
channels are found there, we reduce the max period and buffer sizes
accordingly.
You may wonder that the patch adds only the evaluation of channels
between streams, and what about other parameters? Both the format and
the rate are tied in the implicit fb mode, hence they are always
identical.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215792
Fixes: 5a6c3e11c9 ("ALSA: usb-audio: Add hw constraint for implicit fb sync")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220407211657.15087-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix:
sound/usb/midi.c: In function ‘snd_usbmidi_out_endpoint_create’:
sound/usb/midi.c:1389:2: error: case label does not reduce to an integer constant
case USB_ID(0xfc08, 0x0101): /* Unknown vendor Cable */
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
[ A slight correction with parentheses around the argument by tiwai ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220405151517.29753-3-bp@alien8.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.
Fix this by applying the existing quirk for this kind of issue when the
device is detected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311201400.235892-1-lars@metafoo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Scarlett Gen 2/3 interfaces with internal mixers have a
"standalone" mode. When the interface is not connected to a USB host
and standalone mode is enabled, the interface will pass audio as
previously configured. This patch adds an ALSA control to allow
enabling/disabling that mode.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/cd88871c5e77abd5c23a4758a1f2ec9fd427fd69.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scarlett2_config_items[] contains the parameters for the configuration
items. The driver previously had two sets of configurations items; one
for devices with no mixer, and one for devices with a mixer. This
patch splits the latter into two (one set for Gen 2 devices and one
set for Gen 3 devices) in preparation for a new item (standalone)
which is present in both but with a different offset.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20969f9ea500684e978c87067fbdc7e73de1f6ed.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
Signed-off-by: Reza Jahanbakhshi <reza.jahanbakhshi@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304212303.195949-1-reza.jahanbakhshi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default mixer resume code treats the errors at restoring the
modified mixer items as a fatal error, and it returns back to the
caller. This ends up in the resume failure, and the device will be
come unavailable, although basically those errors are intermittent and
can be safely ignored.
The problem itself has been present from the beginning, but it didn't
hit usually because the code tries to resume only the modified items.
But now with the recent commit to forcibly initialize each item at the
probe time, the problem surfaced more often, hence it appears as a
regression.
This patch fixes the regression simply by ignoring the errors at
resume.
Fixes: b96681bd58 ("ALSA: usb-audio: Initialize every feature unit once at probe time")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215561
Link: https://lore.kernel.org/r/20220214125711.20531-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 83b7dcbc51 introduced a generic
implicit feedback parser, which fails to execute for M-Audio FastTrack
Ultra sound cards. The issue is with the ENDPOINT_SYNCTYPE check in
add_generic_implicit_fb() where the SYNCTYPE is ADAPTIVE instead of ASYNC.
The reason is that the sync type of the FastTrack output endpoints are
set to adaptive in the quirks table since commit
65f04443c9.
Fixes: 83b7dcbc51 ("ALSA: usb-audio: Add generic implicit fb parsing")
Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220211224913.20683-2-matteomartelli3@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable c is being initialized in an outer for-loop and also
re-initialized inside an inner for-loop. The first initialization
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220207140617.341172-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device provides both audio and video. The original quirk added in
commit 48827e1d6a ("ALSA: usb-audio: Add quirk for VF0770") used
USB_DEVICE to match the vendor and product ID. Depending on module order,
if snd-usb-audio was asked first, it would match the entire device and
uvcvideo wouldn't get to see it. Change the matching to USB_AUDIO_DEVICE
to restore uvcvideo matching in all cases.
Fixes: 48827e1d6a ("ALSA: usb-audio: Add quirk for VF0770")
Reported-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Tested-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Reported-by: Paweł Susicki <pawel.susicki@gmail.com>
Tested-by: Paweł Susicki <pawel.susicki@gmail.com>
Cc: <stable@vger.kernel.org> # 5.4, 5.10, 5.14, 5.15
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Link: https://lore.kernel.org/r/20220131183516.61191-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
clang static analysis reports this representative issue
mixer.c:1548:35: warning: Assigned value is garbage or undefined
ucontrol->value.integer.value[0] = val;
^ ~~~
The filter_error() macro allows errors to be ignored.
If errors can be ignored, initialize variables
so garbage will not be used.
Fixes: 48cc429735 ("ALSA: usb-audio: Filter error from connector kctl ops, too")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220126182142.1184819-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
sound/usb/mixer_scarlett_gen2.c:1064:28: warning: using sizeof on a flexible structure
sound/usb/mixer_scarlett_gen2.c:1065:29: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220120211600.GA28841@embeddedor
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB audio device 0db0:419c based on the Realtek ALC4080 chip exposes
all playback volume controls as "PCM". This is makes distinguishing the
individual functions hard.
The added mapping distinguishes all playback volume controls as their
respective function:
- Speaker - for back panel output
- Frontpanel Headphone - for front panel output
- IEC958 - for digital output on the back panel
This clarifies the individual volume control functions for users.
Signed-off-by: Johannes Schickel <lordhoto@gmail.com>
Link: https://lore.kernel.org/r/20220115140257.8751-1-lordhoto@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Olivia Mackintosh has posted to alsa-devel reporting that
there's a potential bug that could break mixer quirks for Pioneer
devices introduced by 6d27788160
"ALSA: usb-audio: Add support for the Pioneer DJM 750MK2
Mixer/Soundcard".
This happened because the DJM 750 MK2 was added last to the Pioneer DJM
device table index and defined as 0x4 but was added to snd_djm_devices[]
just after the DJM 750 (MK1) entry instead of last, after the DJM 900
NXS2. This escaped review.
To prevent that from ever happening again, Takashi Iwai suggested to use
C99 array designators in snd_djm_devices[] instead of simply reordering
the entries.
Fixes: 6d27788160 ("ALSA: usb-audio: Add support for the Pioneer DJM 750MK2")
Reported-by: Olivia Mackintosh <livvy@base.nu>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/Yau46FDzoql0SNnW@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change made mistakenly the stream for capture started at
prepare stage. Add the stream direction check to avoid it.
Fixes: 9c9a3b9da8 ("ALSA: usb-audio: Rename early_playback_start flag with lowlatency_playback")
Link: https://lore.kernel.org/r/20211119102629.7476-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent regression report revealed that the judgment of the
low-latency playback mode based on the runtime->stop_threshold cannot
work reliably at the prepare stage, as sw_params call may happen at
any time, and PCM dmix actually sets it up after the prepare call.
This ended up with the stall of the stream as PCM ack won't be issued
at all.
For addressing this, check the free-wheeling mode again at the PCM
trigger right before starting the stream again, and allow switching to
the non-LL mode at a late stage.
Fixes: d5f871f89e ("ALSA: usb-audio: Improved lowlatency playback support")
Reported-and-tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20211117161855.m45mxcqszkfcetai@box.shutemov.name
Link: https://lore.kernel.org/r/20211119102459.7055-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices do mute the volume at the minimal volume, and for such
devices, we need to set SNDRV_CTL_TLVT_DB_MINMAX_MUTE to the TLV
information. It corresponds to setting usb_mixer_elem_info.min_mute
flag in the USB-audio driver.
This patch adds a new field min_mute in usbmix_dB_map so that the
mixer map entry can pass the flag.
Link: https://lore.kernel.org/r/20211116065415.11159-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The values in usbmix_dB_map should be rather signed while we're using
u32. As the copied target (usb_mixer_elem_info.dBmin and dBmax) is
int, let's make them also int.
Link: https://lore.kernel.org/r/20211116065415.11159-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency
quirk as well.
The device is basically just the HX-Stomp with some more buttons on
the face. I've done some recording with it after adding it, and it
seems to function properly with this fix. The Midi features appear to
be working as well.
[ a coding style fix and patch reformat by tiwai ]
Signed-off-by: Jason Ormes <skryking@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030200405.1358678-1-skryking@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another device ID for JBL Quantum 400. It requires the same quirk as
other JBL Quantum devices.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030174308.1011825-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org # 2.6.34
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026095401.26522-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB control and bulk message timeouts are specified in milliseconds and
should specifically not vary with CONFIG_HZ.
Fixes: c6d43ba816 ("ALSA: usb/6fire - Driver for TerraTec DMX 6Fire USB")
Cc: stable@vger.kernel.org # 2.6.39
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025121142.6531-2-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pointer cs_desc return from snd_usb_find_clock_source could
be null, so there is a potential null pointer dereference issue.
Fix this by adding a null check before dereference.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Link: https://lore.kernel.org/r/20211024111736.11342-1-cyeaa@connect.ust.hk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a Jieli Technology USB Webcam is connected, the video part works
well, but the mic sound is speeded up. On dmesg there are messages
about different rates from the runtime rates, warnings about volume
resolution and lastly, the log is filled, every 5 seconds, with
retire_capture_urb error messages.
The mic works only when ep packet size is set to wMaxPacketSize (normal
sound and no more retire_capture_urb error messages). Skipping reading
sample rate, fixes the messages about different rates and forcing a volume
resolution, fixes warnings about volume range. I have arbitrarily choosed
the value (16): I read in a comment that there should be no more than 255
levels, so 4096 (max volume) / 16 = 0-255.
Signed-off-by: Marco Giunta <giun7a@gmail.com>
Link: https://lore.kernel.org/r/20211018162552.12082-1-giun7a@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13
The GSP670 has 2 playback and 1 recording device that by default are
detected in an incompatible order for alsa. This may have been done to make
it compatible for the console by the manufacturer and only affects the
latest firmware which uses its own ID.
This quirk will resolve this by reordering the channels.
Signed-off-by: Brendan Grieve <brendan@grieve.com.au>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211015025335.196592-1-brendan@grieve.com.au
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we used to read the current value of the mixer element
dynamically at the first access, and the error from a GET_CUR message
is treated as a fatal error (unless QUIRK_IGNORE_CTL_ERROR is set).
It's rather inconvenient, as most of GET_CUR errors are no fatal, and
we can continue operation with assumption of some fixed value.
This patch makes the USB-audio driver to change the behavior at probe
time; now it tries to initialize the current value of each mixer
element that is built from a feature unit (those for typically for
mixer volumes and switches). When a read failure happens, it tries to
set the known minimum value. After that point, a cached value is used
always, hence we won't hit GET_CUR message error any longer.
The error from GET_CUR message is still shown as a warning normally,
but only once at the probe time, and it'll keep operating. If the
message is confirmed to be harmless, it can be shut up by
QUIRK_IGNORE_CTL_ERROR quirk flag, too.
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211014130636.17860-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error from snd_usb_lock_shutdown() indicates that the device is
disconnected, hence it makes no sense to show any further control
message error in get_ctl_value_v2(). Return the error directly
instead.
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211014130636.17860-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error message in get_ctl_value_v2() (for UAC2/3) is shown via
KERN_ERR level but it was intended to be rather a debug message as
seen in get_ctl_value_v1() (for UAC1). This patch downgrade the
printk level.
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211014130636.17860-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A back-merge of 5.15 branch into 5.16-devel branch for further
development of USB and ALSA core stuff that depends on 5.15 fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Shciit Hel device responds to the ctl message for the mic capture
switch with a timeout of -EPIPE:
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
usb 7-2.2: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x1100, type = 1
This seems safe to ignore as the device works properly with the control
message quirk, so add it to the quirk table so all is good.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/YWgR3nOI1osvr5Yo@kroah.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device advertises 8 formats, but only a rate of 48kHz is honored
by the hardware and 24 bits give chopped audio, so only report the
one working combination. This fixes out-of-the-box audio experience
with PipeWire which otherwise attempts to choose S24_3LE (while
PulseAudio defaulted to S16_LE).
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012200906.3492-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent support for the improved low-latency playback mode applied
the SNDRV_PCM_INFO_EXPLICIT_SYNC flag for the target streams, but this
was a slight overkill. The use of the flag above disables effectively
both PCM status and control mmaps, while basically what we want to
track is only about the appl_ptr update.
For less restriction, use a more proper flag,
SNDRV_PCM_INFO_SYNC_APPLPTR instead, which disables only the control
mmap.
Fixes: d5f871f89e ("ALSA: usb-audio: Improved lowlatency playback support")
Link: https://lore.kernel.org/r/20211011103650.10182-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel already has support for very similar Pioneer djm products
and this work is based on that.
Added device to quirks-table.h and added control info to
mixer_quirks.c.
Tested on my hardware and all working.
Signed-off-by: William Overton <willovertonuk@gmail.com>
Link: https://lore.kernel.org/r/20211010145841.11907-1-willovertonuk@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a stream is in the implicit feedback mode, it's more or less tied
with a capture stream. Passing SNDRV_PCM_INFO_JOINT_DUPLEX may help
for user-space to understand the situation.
Link: https://lore.kernel.org/r/20211007083528.4184-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Scarlett device series from Focusrite Novation seem requiring the
sample rate validations as we've done for MOTU devices; otherwise the
driver probes invalid audioformat entries that contain the sample
rates that actually don't work, and this may result in an incomplete
setup as reported recently.
This patch adds the needed quirk flag for enabling the sample rate
validation for Focusrite Novation devices.
Fixes: fe773b8711 ("ALSA: usb-audio: workaround for iface reset issue")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214493
Link: https://lore.kernel.org/r/20211004074050.28241-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Behringer UFX1204 and UFX1604 have Synchronous endpoints to which
current ALSA code applies implicit feedback sync as if they were
Asynchronous endpoints. This breaks UAC compliance and is unneeded.
The commit 5e35dc0338 and subsequent
1a15718b41 were meant to clear up noise.
Unfortunately, noise persisted for those using higher sample rates and
this was only solved by commit d2e8f64125
Since there are no more reports of noise, let's get rid of the
implicit-fb quirks breaking UAC compliance.
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/YVYSnoQ7nxLXT0Dq@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While draining a stream, ALSA PCM core stops the stream by issuing
snd_pcm_stop() after all data has been sent out. And, at PCM trigger
stop, currently USB-audio driver kills the in-flight URBs explicitly,
then at sync-stop ops, sync with the finish of all remaining URBs.
This might result in a drop of the drained samples as most of
USB-audio devices / hosts allow relatively long in-flight samples (as
a sort of FIFO).
For avoiding the trimming, this patch changes the stream-stop behavior
during PCM draining state. Under that condition, the pending URBs
won't be killed. The leftover in-flight URBs are caught by the
sync-stop operation that shall be performed after the trigger-stop
operation.
Link: https://lore.kernel.org/r/20210929080844.11583-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is another attempt to improve further the handling of playback
stream in the low latency mode. The latest workaround in commit
4267c5a8f3 ("ALSA: usb-audio: Work around for XRUN with low latency
playback") revealed that submitting URBs forcibly in advance may
trigger XRUN easily. In the classical mode, this problem was avoided
by practically delaying the submission of the actual data with the
pre-submissions of silent data before triggering the stream start.
But that is exactly what we want to avoid.
Now, in this patch, instead of the previous workaround, we take a
similar approach as used in the implicit feedback mode. The URBs are
queued at the PCM trigger start like before, but we check whether the
buffer has been already filled enough before each submission, and
stop queuing if the data overcomes the threshold. The remaining URBs
are kept in the ready list, and they will be retrieved in the URB
complete callback of other (already queued) URBs. In the complete
callback, we try to fill the data and submit as much as possible
again. When there is no more available in-flight URBs that may handle
the pending data, we'll check in PCM ack callback and submit and
process URBs there in addition. In this way, the amount of in-flight
URBs may vary dynamically and flexibly depending on the available data
without hitting XRUN.
The following things are changed to achieve the behavior above:
* The endpoint prepare callback is changed to return an error code;
when there is no enough data available, it may return -EAGAIN.
Currently only prepare_playback_urb() returns the error.
The evaluation of the available data is a bit messy here; we can't
check with snd_pcm_avail() at the point of prepare callback (as
runtime->status->hwptr hasn't been updated yet), hence we manually
estimate the appl_ptr and compare with the internal hwptr_done to
calculate the available frames.
* snd_usb_endpoint_start() doesn't submit full URBs if the prepare
callback returns -EAGAIN, and puts the remaining URBs to the ready
list for the later submission.
* snd_complete_urb() treats the URBs in the low-latency mode similarly
like the implicit feedback mode, and submissions are done in
(now exported) snd_usb_queue_pending_output_urbs().
* snd_usb_queue_pending_output_urbs() again checks the error value
from the prepare callback. If it's -EAGAIN for the normal stream
(i.e. not implicit feedback mode), we push it back to the ready list
again.
* PCM ack callback is introduced for the playback stream, and it calls
snd_usb_queue_pending_output_urbs() if there is no in-flight URB
while the stream is running. This corresponds to the case where the
system needs the appl_ptr update for re-submitting a new URB.
* snd_usb_queue_pending_output_urbs() and the prepare EP callback
receive in_stream_lock argument, which is a bool flag indicating the
call path from PCM ack. It's needed for avoiding the deadlock of
snd_pcm_period_elapsed() calls.
* Set the new SNDRV_PCM_INFO_EXPLICIT_SYNC flag when the new
low-latency mode is deployed. This assures catching each applptr
update even in the mmap mode.
Fixes: 4267c5a8f3 ("ALSA: usb-audio: Work around for XRUN with low latency playback")
Link: https://lore.kernel.org/r/20210929080844.11583-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In theory, stop_urbs() may be called concurrently.
Although we have the state check beforehand, it's safer to apply
ep->lock during the critical list head manipulations.
Link: https://lore.kernel.org/r/20210929080844.11583-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is yet more preparation for the upcoming changes.
Extend snd_usb_endpoint_next_packet_size() to check the available
frames and return -EAGAIN if the next packet size is equal or exceeds
the given size. This will be needed for avoiding XRUN during the low
latency operation.
As of this patch, avail=0 is passed, i.e. the check is skipped and no
behavior change.
Link: https://lore.kernel.org/r/20210929080844.11583-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a playback stream runs in the implicit feedback mode, its
operation is passive and won't start unless the capture packet is
received. This behavior contradicts with the low-latency playback
mode, and we should turn off lowlatency_playback flag accordingly.
In theory, we may take the low-latency mode when the playback-first
quirk is set, but it still conflicts with the later operation with the
fixed packet numbers, so it's disabled all together for now.
Link: https://lore.kernel.org/r/20210929080844.11583-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The free-wheel stream operation like dmix may not update the appl_ptr
appropriately, and it doesn't fit with the low-latency playback mode.
Disable the low-latency playback operation when the stream is set up
in such a mode.
Link: https://lore.kernel.org/r/20210929080844.11583-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preparation patch for the upcoming low-latency improvement
changes.
Rename early_playback_start flag with lowlatency_playback as it's more
intuitive. The new flag is basically a reverse meaning.
Along with the rename, factor out the code to set the flag to a
function. This makes the complex condition checks simpler.
Also, the same flag is introduced to snd_usb_endpoint, too, that is
carried from the snd_usb_substream flag. Currently the endpoint flag
isn't still referred, but will be used in later patches.
Link: https://lore.kernel.org/r/20210929080844.11583-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB-audio driver tries to sync with the clear of all pending URBs in
wait_clear_urbs(), and it waits for all bits in active_mask getting
cleared. This works fine for the normal operations, but when a stream
is managed in the implicit feedback mode, there is still a very thin
race window: namely, in snd_complete_usb(), the active_mask bit for
the current URB is once cleared before re-submitted in
queue_pending_output_urbs(). If wait_clear_urbs() is called during
that period, it may pass the test and go forward even though there may
be a still pending URB.
For covering it, this patch adds a new counter to each endpoint to
keep the number of in-flight URBs, and changes wait_clear_urbs()
checking this number instead. The counter is decremented at the end
of URB complete, hence the reference is kept as long as the URB
complete is in process.
Link: https://lore.kernel.org/r/20210929080844.11583-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a single clock source is shared among several endpoints, we have
to keep the same rate on all active endpoints as long as the clock is
being used. For dealing with such a case, this patch adds one more
check in the hw params constraint for the rate to take the shared
clocks into account. The current rate is evaluated from the endpoint
list that applies the same clock source.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190418
Link: https://lore.kernel.org/r/20210929080844.11583-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usb_find_clock_source and snd_usb_find_clock_selector are helper
macros that look at an entity id and validate that this entity id is
in fact a clock source or a clock selector. The present comments
inside __uac_clock_find_source give the reader the impression we're
looking for an entity id.
We're looking for an entity id indeed, the clock source, but since
__uac_clock_find_source is recursive, we're also looking *at* the
entity ids, in the search for the one clock source.
Fix the comment so we don't give readers a wrong idea.
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/YU6Kj05oOqRmhJDf@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
In this case this is not actually dynamic size: all the operands
involved in the calculation are constant values. However it is better to
refactor this anyway, just to keep the open-coded math idiom out of
code.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + size * count" in the kzalloc() function.
Also, take the opportunity to refactor the declaration variables to make
it more easy to read.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210919133727.44694-1-len.baker@gmx.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB-audio driver assumes that the normal resume would preserve the
device configuration while reset_resume wouldn't, and tries to restore
the mixer elements only at reset_resume callback. However, this seems
too naive, and some devices do behave differently, resetting the
volume at the normal resume; this resulted in the inconsistent volume
that surprised users.
This patch changes the mixer resume code to handle both the normal and
reset resume in the same way, always restoring the original mixer
element values. This allows us to unify the both callbacks as well as
dropping the no longer used reset_resume field, which ends up with a
good code reduction.
A slight behavior change by this patch is that now we assign
restore_mixer_value() as the default resume callback, and the function
is no longer called at reset-resume when the resume callback is
overridden by the quirk function. That is, if needed, the quirk
resume function would have to handle similarly as
restore_mixer_value() by itself.
Reported-by: En-Shuo Hsu <enshuo@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Link: https://lore.kernel.org/r/CADDZ45UPsbpAAqP6=ZkTT8BE-yLii4Y7xSDnjK550G2DhQsMew@mail.gmail.com
Link: https://lore.kernel.org/r/20210910105155.12862-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another device ID for JBL Quantum 800. It requires the same quirk as
other JBL Quantum devices.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210831002531.116957-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making user to switch back to the old playback mode, this patch
adds a new module option 'lowlatency' to snd-usb-audio driver.
When user face a regression due to the recent low-latency playback
support, they can test easily by passing lowlatency=0 option without
rebuilding the kernel.
Fixes: 307cc9baac ("ALSA: usb-audio: Reduce latency at playback start, take#2")
Link: https://lore.kernel.org/r/20210829073830.22686-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change for low latency playback works in most of test cases
but it turned out still to hit errors on some use cases, most notably
with JACK with small buffer sizes. This is because USB-audio driver
fills up and submits full URBs at the beginning, while the URBs would
return immediately and try to fill more -- that can easily trigger
XRUN. It was more or less expected, but in the small buffer size, the
problem became pretty obvious.
Fixing this behavior properly would require the change of the
fundamental driver design, so it's no trivial task, unfortunately.
Instead, here we work around the problem just by switching back to the
old method when the given configuration is too fragile with the low
latency stream handling. As a threshold, we calculate the total
buffer bytes in all plus one URBs, and check whether it's beyond the
PCM buffer bytes. The one extra URB is needed because XRUN happens at
the next submission after the first round.
Fixes: 307cc9baac ("ALSA: usb-audio: Reduce latency at playback start, take#2")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210827203311.5987-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent quirk for WALKMAN (commit 7af5a14371: "ALSA: usb-audio:
Fix regression on Sony WALKMAN NW-A45 DAC") may be required for other
devices and is worth to be put into the common quirk flags.
This patch adds a new quirk flag bit QUIRK_FLAG_SET_IFACE_FIRST and a
quirk table entry for the device.
Link: https://lore.kernel.org/r/20210824055720.9240-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report for USB-audio with Sony WALKMAN NW-A45
DAC device where no sound is audible on recent kernel. The bisection
resulted in the code change wrt endpoint management, and the further
debug session revealed that it was caused by the order of the USB
audio interface. In the earlier code, we always set up the USB
interface at first before other setups, but it was changed to be done
at the last for UAC2/3, which is more standard way, while keeping the
old way for UAC1. OTOH, this device seems requiring the setup of the
interface at first just like UAC1.
This patch works around the regression by applying the interface setup
specifically for the WALKMAN at the beginning of the endpoint setup
procedure. This change is written straightforwardly to be easily
backported in old kernels. A further cleanup to move the workaround
into a generic quirk section will follow in a later patch.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214105
Link: https://lore.kernel.org/r/20210824054700.8236-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a second mixer control to Digidesign Mbox
to select between Analog/SPDIF capture.
Users will note that selecting the SPDIF input source
automatically switches the clock mode to sync to SPDIF,
which is a feature of the hardware.
(You can change the clock source back to internal if you want
to capture from spdif but not sync to its clock although this mode
is probably not recommended).
Unfortunately, starting the stream resets both modes
to Internally clocked and Analog input mode.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Tested-by: Damien Zammit <damien@zamaudio.com>
Link: https://lore.kernel.org/r/20210813113402.11849-1-damien@zamaudio.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate array names_to_check on the stack but instead it
static. Makes the object code smaller by 56 bytes. Also clean
up checkpatch warning by adding extra const for names_to_check
and pointer s.
Before:
text data bss dec hex filename
103512 34380 0 137892 21aa4 ./sound/usb/mixer.o
After:
text data bss dec hex filename
103264 34572 0 137836 21a6c ./sound/usb/mixer.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210803122839.7143-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new module option, quirk_flags, for allowing user to
try some additional device-specific quirk behavior more easily.
When this option is set to non-zero, it overrides the quirk_flags, and
the specific workaround is applied.
Link: https://lore.kernel.org/r/20210729074404.19728-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer code has a flag ignore_ctl_error for ignoring the errors
returned from the device wrt mixer accesses, and this is set from the
entries in mixer_maps.c, as well as ignore_ctl_error module option.
Those can be well integrated into the new quirk_flags field, too.
Link: https://lore.kernel.org/r/20210729074404.19728-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-suspend suppression workaround for Lenovo machines are
handled in quirks-table.h. Now it's more easier to handle with
quirk_flags.
Link: https://lore.kernel.org/r/20210729074404.19728-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rate validation at the device probe is applied only to the
specific devices (currently only for MOTU devices), and this check can
be moved to quirk_flags gracefully, too.
Link: https://lore.kernel.org/r/20210729074404.19728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We apply some delay for the control messages on certain devices as a
workaround, and this can be moved into the quirk_flags as well.
Currently there are three different delay periods (1ms, 5ms and 20ms),
so three different quirk bits are assigned for them.
Link: https://lore.kernel.org/r/20210729073855.19043-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is another quirk for the transfer, and that's currently specific
to Zoom R16/24, handled in create_standard_audio_quirk(). Let's move
this also to the new quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The txfr_quirk field was meant for aligning the transfer, and it's set
for certain devices in quirks-table.h. Now we can move that stuff
also to the new quirk_flags gracefully, and reduce the quirks-table.h
entries (that are exposed to module device table).
As the quirks-table.h entries are also with the name string override,
provide the corresponding entries to the usb_audio_names[] table,
too.
Link: https://lore.kernel.org/r/20210729073855.19043-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The devices that can have media-controller API entries are currently
specified via tables in quirks-table.h, as a part of descriptor
override. This can fit better to the new quirk_flags, as we just need
a matching with the given ID and create the MC entries accordingly.
Link: https://lore.kernel.org/r/20210729073855.19043-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As more and more device-specific workarounds came up and gathered in
various places, it becomes harder to manage. Now it's time to clean
up and collect workarounds more consistently and make them more easily
applicable.
This patch is the first step for that: a new field quirk_flags is
introduced in snd_usb_audio struct to contain the bit flags for
various device-specific quirks. Those are separate one from the
quirks in quirks-table.h; the quirks-table.h entries are for more
intrusive stuff that needs the descriptor override, while the new
quirk_flags is for easier ones that are tied with the vendor:product
IDs.
In this patch, as the first example, we convert the list of devices
and vendors to ignore GET_SAMPLE_RATE, formerly defined in
snb_usb_get_sample_rate_quirk().
Link: https://lore.kernel.org/r/20210729073855.19043-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the resume on Lenovo machines seems causing a
regression on others. It's because the change always triggers the
connector selection no matter which widget node type is.
This patch addresses the regression by setting the resume callback
selectively only for the connector widget.
Fixes: 44609fc01f ("ALSA: usb-audio: Check connector value on resume")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213897
Link: https://lore.kernel.org/r/20210729185126.24432-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently JBL Quantum 600 has multiple hardware revisions. Apply
registration quirk to another device id as well.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210727093326.1153366-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The values of the line output controls can change when the SW/HW
switches are set to HW, and also when speaker switching is enabled.
These notifications were sent with a mask of only
SNDRV_CTL_EVENT_MASK_INFO. Change the notifications to set the
SNDRV_CTL_EVENT_MASK_VALUE mask bit as well.
When the mute control is updated, the notification was sent with a
mask of SNDRV_CTL_EVENT_MASK_INFO. Change the mask to the correct
value of SNDRV_CTL_EVENT_MASK_VALUE.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/8192e15ba62fa4bc90425c005f265c0de530be20.1626959758.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the hardware mute button is pressed, private->vol_updated is set
so that the mute status is invalidated. As the channel mute values may
be affected by the global mute value, update scarlett2_mute_ctl_get()
to call scarlett2_update_volumes() if private->vol_updated is set.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/aa18ddbf8d8bd7f31832ab1b6b6057c00b931202.1626959758.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN,
but it wasn't added in the table in snd_usb_mixer_dump_cval(). This
is no big problem since each bespoken type should have its own dump
method, but it still isn't disallowed to use the standard one, so we
should cover it as well. Along with it, define the table with the
explicit array initializer for avoiding other pitfalls.
Fixes: 785b6f29a7 ("ALSA: usb-audio: scarlett2: Fix wrong resume call")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is another attempt for the reduction of the latency at the start
of a USB audio playback stream. The first attempt in the commit
9ce650a75a caused an unexpected regression (a deadlock with pipewire
usage) and was later reverted by the commit 4b820e167b. The devils
are always living in details, of course; the cause of the deadlock was
the call of snd_pcm_period_elapsed() inside prepare_playback_urb()
callback. In the original code, this callback is never called from
the stream lock context as it's driven solely from the URB complete
callback. Along with the movement of the URB submission into the
trigger START, this prepare call may be also executed in the stream
lock context, hence it deadlocked with the another lock in
snd_pcm_period_elapsed(). (Note that this happens only conditionally
with a small period size that matches with the URB buffer length,
which was a reason I overlooked during my tests. Also, the problem
wasn't seen in the capture stream because the capture stream handles
the period-elapsed only at retire callback that isn't executed at the
trigger.)
If it were only about avoiding the deadlock, it'd be possible to use
snd_pcm_period_elapsed_under_stream_lock() as a solution. However, in
general, the period elapsed notification must be sent after the actual
stream start, and replacing the call wouldn't satisfy the pattern.
A better option is to delay the notification after the stream start
procedure finished, instead. In the case of USB framework, one of the
fitting place would be the complete callback of the first URB.
So, as a workaround of the deadlock and the order fixes above, in
addition to the re-applying the changes in the commit 9ce650a75a,
this patch introduces a new flag indicating the delayed period-elapsed
handling and sets it under the possible deadlock condition
(i.e. prepare callback being called before subs->running is set).
Once when the flag is set, the period-elapsed call is handled at a
later URB complete call instead.
As a reference for the original motivation for the low-latency change,
I cite here again:
| USB-audio driver behaves a bit strangely for the playback stream --
| namely, it starts sending silent packets at PCM prepare state while
| the actual data is submitted at first when the trigger START is
| kicked off. This is a workaround for the behavior where URBs are
| processed too quickly at the beginning. That is, if we start
| submitting URBs at trigger START, the first few URBs will be
| immediately completed, and this would result in the immediate
| period-elapsed calls right after the start, which may confuse
| applications.
|
| OTOH, submitting the data after silent URBs would, of course, result
| in a certain delay of the actual data processing, and this is rather
| more serious problem on modern systems, in practice.
|
| This patch tries to revert the workaround and lets the URB
| submission starting at PCM trigger for the playback again. As far
| as I've tested with various backends (native ALSA, PA, JACK, PW), I
| haven't seen any problems (famous last words :)
|
| Note that the capture stream handling needs no such workaround,
| since the capture is driven per received URB.
Link: https://lore.kernel.org/r/4e71531f-4535-fd46-040e-506a3c256bbd@marcan.st
Link: https://lore.kernel.org/r/s5hbl7li0fe.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210707112447.27485-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 9ce650a75a.
This commit causes watchdog lockups on my machine, and while I have no
idea what the cause is, it bisected right to this commit, and reverting
the change promptly fixes it.
At least occasionally one of the watchdog call traces was
Call Trace:
_raw_spin_lock_irqsave+0x35/0x40
snd_pcm_period_elapsed+0x1b/0xa0 [snd_pcm]
snd_usb_endpoint_start+0x1a0/0x3c0 [snd_usb_audio]
start_endpoints+0x23/0x90 [snd_usb_audio]
snd_usb_substream_playback_trigger+0x7b/0x1a0 [snd_usb_audio]
snd_pcm_common_ioctl+0x1c44/0x2360 [snd_pcm]
snd_pcm_ioctl+0x2e/0x40 [snd_pcm]
__se_sys_ioctl+0x72/0xc0
do_syscall_64+0x4c/0xa0
entry_SYSCALL_64_after_hwframe+0x44/0xae
so presumably it's a locking error on that substream spinlock that
snd_pcm_period_elapsed() takes. But at this point I just want to have a
working system so that I can continue the merge window work tomorrow.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clang warns:
sound/usb/mixer_scarlett_gen2.c:1189:32: warning: expression result
unused [-Wunused-value]
for (i = 0; i < count; i++, (u16 *)buf++)
^ ~~~~~
1 warning generated.
It appears the intention was to cast the void pointer to a u16 pointer
so that the data could be iterated through like an array of u16 values.
However, the cast happens after the increment because a cast is an
rvalue, whereas the post-increment operator only works on lvalues, so
the loop does not iterate as expected. This is not a bug in practice
because count is not greater than one at the moment but this could
change in the future so this should be fixed.
Replace the cast with a temporary variable of the proper type, which is
less error prone and fixes the iteration. Do the same thing for the
'u8 *' below this if block.
Fixes: ac34df733d ("ALSA: usb-audio: scarlett2: Update get_config to do endian conversion")
Link: https://github.com/ClangBuiltLinux/linux/issues/1408
Acked-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210627051202.1888250-1-nathan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mixer control put callbacks should return 1 if the value is changed.
Fix the mute, air, phantom, direct monitor, speaker switch, talkback,
and MSD controls accordingly.
Fix scarlett2_speaker_switch_enable() to not ignore the return value
of scarlett2_sw_hw_change().
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/76643f7ac81aef93351122d07881e30d51dcb1b9.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 18i8 Gen 3 has 4 inputs with a pad control, not 2. Update
s18i8_gen3_info.pad_input_count.
Reported-by: Aaron Wolf <aaron@wolftune.com>
Tested-by: Aaron Wolf <aaron@wolftune.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/29a6ce412a42373daab7c96c395560461fcf08c6.1624798436.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For configuration items with a size of 16, scarlett2_usb_get_config()
was filling *buf with little-endian data. Update it to convert to CPU
endian. This function is not currently used so affects nothing yet;
will be used by the upcoming talkback feature.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/cbc8b6eedd859dd27086ab4126d724a86dd50bcb.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 18i8 and 18i20 Gen 3 support "speaker switching". Add a Speaker
Switch control which can be set to Off/Main/Alt.
When speaker switching is enabled or disabled, the interface may
change the state of the Analog Outputs 3 and 4 routing and the global
mute button, so use a flag private->speaker_switching_switched to note
that those should be checked when the next "monitor other"
notification is received.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/874193a534cd0aeb6f2e108ae761cadd2dc25ad2.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enabling/disabling speaker switching will update the mux
configuration. To prepare for this, add a private->mux_updated flag
and update the scarlett2_mux_src_enum_ctl_get() callback to check it.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/5ce3bb9fe4006b550d18c783c5ff640fe0bfbfcb.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Save the struct snd_kcontrol pointers for the sw_hw and mux controls.
This is in preparation for speaker switching support which needs to be
able to update those controls.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/269d89181bf29dbea80ba6f8cfff84fb23b77f86.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split part of scarlett2_sw_hw_enum_ctl_put() out into
scarlett2_sw_hw_change() so that the code which actually makes the
change is available in its own function. This will be used by the
speaker switching support which needs to set the SW/HW switch to HW
when speaker switching is enabled.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/f2cf91841ba067b490e7709bc4b14f4532b4ddd5.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Solo and 2i2 devices don't have a mixer but they do have a "direct
monitor" switch. Add support for getting and setting the state of this
switch.
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/61d23dc4feb3b046d870ad7203e66ff2bd1d278c.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some inputs on Gen 3 models support software-selectable phantom power.
Add support for getting and setting the state of those switches and
the "Phantom Power Persistence" switch.
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/5837ce8a8c686560fc8f40b4204dd2a10721869b.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some inputs on Gen 3 models have an "air" feature which can be enabled
from the driver or (model-dependent) from the front panel. Add support
for getting and setting the state of those switches.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/44d448a4150b9c068754759c9fdd2bfe21484487.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add initial support for the Focusrite Scarlett Solo and 2i2 devices:
- They have no mixer
- They don't support reporting sync status or levels
- The configuration space is laid out differently to the other models
- There is no level (line/inst) switch on input 1 of the Solo
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/190b90f6f1f8f8d4dfb5f0a7761ff8ae5c40fdde.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move scarlett2_usb_get() and scarlett2_usb_get_config() above the
functions relating to updating the configuration so that
scarlett2_usb_set_config() can call scarlett2_usb_get() in a
subsequent patch.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/1549f8e44548be679119f0b1462f888f4a03812d.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models allow the level and pad settings to be controlled from the
front-panel of the device. For these, the device will send an
"input-other" notification to prompt the driver to re-read the status
of those settings.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/06289a7697455e96b7dbdfd2d384d4b20f8df6e0.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current way of the scarlett2 mixer code managing the
usb_mixer_elem_info object is wrong in two ways: it passes its
internal index to the head.id field, and the val_type field is
uninitialized. This ended up with the wrong execution at the resume
because a bogus unit id is passed wrongly. Also, in the later code
extensions, we'll have more mixer elements, and passing the index will
overflow the unit id size (of 256).
This patch corrects those issues. It introduces a new value type,
USB_MIXER_BESPOKEN, which indicates a non-standard mixer element, and
use this type for all scarlett2 mixer elements, as well as
initializing the fixed unit id 0 for avoiding the overflow.
Tested-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/49721219f45b7e175e729b0d9d9c142fd8f4342a.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The scarlett2_ports struct contains both generic (hardware IDs and
descriptions) and model-specific (port count) data. Remove the generic
data from the scarlett2_device_info struct so it is not repeated for
every model.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/7a9e57e4e55a482390c692a9e60731d72b664a15.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Gen 3 devices do not put all of the mux entries for the same port
types together in order in the "set mux" message data. To prepare for
this, replace the struct scarlett2_ports num[] array and the
assignment_order[] array with mux_assignment[], a list of port types
and ranges that is defined in the struct scarlett2_device_info.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/08e8d784d78262cb57496d28ef1ad7b6213a90ab.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For each analogue output, in addition to the output volume (gain)
control, the hardware also has a mute control. Add ALSA mute controls
for each analogue output.
If the device has the line_out_hw_vol feature, then the mute control
is disabled along with the output volume control when the switch is
set to HW.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/6fad82174b44633e46cfd96332a038de74d544f2.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the USB device ID to the scarlett2_device_info struct so that the
switch statement which finds the appropriate struct can be replaced
with a loop that looks through an array of pointers to those structs.
Suggested-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/474c408c29fb280a611e47e49e59ca2fb9810d27.1624294591.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At extending the available mixer values for 32bit types, we forgot to
add the corresponding entries for the format dump in the proc output.
This may result in OOB access. Here adds the missing entries.
Fixes: bc18e31c30 ("ALSA: usb-audio: Fix parameter block size for UAC2 control requests")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622090647.14021-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the hard-coded interface number and related constants for the
vendor-specific interface and look them up from the USB endpoint
descriptor.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164652.GA9237@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
