bytesperline is calculated in multiple places, store it in the coda_q_data
structure. This will be more useful later when adding JPEG support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On i.MX53 and i.MX6, the CODA VPU can be reset by the System Reset Controller.
We can use this to get out of dire situations, for example after a picture
run timeout.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename the per-context prescan_failed variable to hold, as this is what the
flag does: it temporarily keeps the coda from running until new data is fed
into the bitstream buffer or stop_streaming is called on the input side.
A prescan failure on i.MX5 is one possible reason to enter this state, another
one is a picture run timeout on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda h.264 decoder also counts PIC_RUNs where no frame was decoded but
a frame was rotated out / marked as ready to be displayed. This causes an
offset between the incoming encoded frame's sequence number and the decode
sequence number returned by the coda. This patch introduces a sequence
counter offset variable to keep track of the difference.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the CODA reports macroblock errors, also set the VB2_BUF_STATE_ERROR flag
to alert userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The coda driver advertises timestamp_type V4L2_BUF_FLAG_TIMESTAMP_COPY on
both queues, so we have to copy timestamps from input v4l2 buffers to the
corresponding destination v4l2 buffers. Since the h.264 decoder can reorder
frames, a timestamp queue is needed to keep track of and assign the correct
timestamp to destination buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case no further buffers are queued after the stop command, restart
job scheduling explicitly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allow userspace to enable cyclic intra refresh by setting the number of
intra macroblocks per frame to a non-zero value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the bitrate control is set, the encoder works in CBR mode, dynamically
changing the quantization parameters to achieve a constant bitrate.
With the min/max QP controls the quantization parameters can be limited
to a given range.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver uses the genalloc API, which doesn't have stubs in
case GENERIC_ALLOCATOR is disabled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This adds a new function coda_check_firmware that does the firmware
version checks so that this can be done only once from coda_probe
instead of every time the runtime pm framework resumes the coda.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch allows to use the runtime pm and generic pm domain frameworks
to completely gate power to the VPU if it is unused. This functionality
is available on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the mem2mem helpers introduced to get rid of some duplicated code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using the coda_mutex lock to serialize hardware access would cause
"INFO: possible circular locking dependency detected" lockdep warnings.
Since the possible locking paths are hard to follow, serialize hardware
access with a single workqueue thread. Ultimately the workqueue could
be converted to only do register setup and readout for per-command work
items.
Using the initialized context property, SEQ_END is only queued in
coda_release when needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The h.264 decoder produces capture frames that are a multiple of the macroblock
size (16 pixels). To inform userspace about invalid pixel data at the edges,
use the active and padded composing rectangles on the capture queue.
The cropping information is obtained from the h.264 sequence parameter set.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows us to get rid of the now superfluous v4l2_m2m_get_vq check
in G_FMT. Also, we can use this to check the buffer type in G_SELECTION
later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the CODA960 VPU in Freescale i.MX6 SoCs.
It enables h.264 and MPEG4 encoding and decoding support. Besides the usual
register shifting, the CODA960 gains frame memory control and GDI registers
that are set up for linear mapping right now, needs ENC_PIC_SRC_INDEX to be
set beyond the number of internal buffers for some reason, and has subsampling
buffers that need to be set up. Also, the work buffer size is increased to
80 KiB.
The CODA960 firmware spins if there is not enough input data in the bitstream
buffer. To make it continue, buffers need to be copied into the bitstream as
soon as they are queued. As the bitstream fifo is written into from two places,
it must be protected with a mutex. For that, using a threaded interrupt handler
is necessary.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest MFC v6 firmware requires tile mode and loop filter
setting to be done as part of Init buffer command, in sync
with v7. This patch adds this support for new v6 firmware.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For MFC firmwares, improved versions with bug fixes and
feature additions are released keeping the firmware version
including major and minor number same. The issue came with
the release of a new MFCv6 firmware with an interface change.
This patch adds the support of accepting multiple firmware
binaries for every version with the driver trying to load
firmwares starting from latest. This ensures full backward
compatibility regardless of which firmware version and kernel
version is used.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The function s5p_mfc_reload_firmware is exactly same as
s5p_mfc_load_firmware. So removing the duplicate function.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bridge driver doesn't support interlaced formats, always return the
field order set to V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CPB size is limited by the hardware. Add this limit to the s_fmt.
Signed-off-by: panpan liu <panpan1.liu@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
OVL and BTP IRAM buffers are never used, setup the bits for
for DBK/BIT/IP usage depending on CODA version in one place.
Also, use a simple allocator function and group IRAM addresses
and size in a coda_aux_buf structure.
This is done in preparation for CODA960 support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
If bitrate is not set, the encoder is running in VBR mode, with the
I- and P-frame quantization parameters configured from userspace.
For the quantization parameters, 0 is a valid value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently the rotator unit is used to copy decoded frames out into buffers
provided by videobuf2. Since the CODA reports the I/P/B frame type of the
last decoded frame, and this frame will be copied out in a later device_run,
depending on display order, we have to store the frame type until such time.
This patch also adds the B-frame type.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fc906b6d "Remove special clock usage in driver" removed
initialization of MFC special clock, arguing that there's
no need to do it explicitly, since it's one of MFC gate clock's
dependencies and gets enabled along with it. However, there's
no promise of keeping this hierarchy across Exynos SoC
releases, therefore this approach fails to provide a stable,
portable solution.
Out of all MFC versions, only v6 doesn't use special clock at all.
For other versions log a message only in case clk_get fails,
as not all the devices with the same MFC version require
initializing the clock explicitly.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the s5p_mfc_alloc_firmware() function there are some mistakes
where the code checks whether the DMA memory is properly allocated or
not.
First of all dma_alloc_coherent() returns NULL in case of error.
The code also checked two times fw_virt_addr, ignoring
the bank2_virt pointer.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pixel color components can be scaled using either bilinear interpolation
or a multitap filter. The multitap filter provides better results, but
can't be selected when the alpha layer need to be scaled down by more
than 1/2.
Disable alpha scaling when the input has a fixed alpha value, and
program the UDS to output a fixed alpha value in that case. This ensures
the multitap filter will be used whenever possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Expose the background color to userspace through the V4L2_CID_BG_COLOR
control.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The BRU outputs premultiplied colors, enable color data normalization
when the format configured at the output of the pipeline isn't
premultiplied.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adjust the BRU blending formula to avoid the multiplication by alpha
when the corresponding input format is premultiplied. As this requires
access to the RPFs connected to the BRU inputs from the BRU module,
store pointers to the RPFs in the BRU structure when validating the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control is used to configure the fixed alpha channel value, when
reading from memory in the RPF or writing to memory in the WPF.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support ARGB formats on the RPF side by reading the alpha component from
memory and on the WPF side by writing it to memory.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver ignores the alpha component on output video nodes and
hardcodes the alpha component to 0 on capture video nodes. Make this
explicit by exposing XRGB formats.
Compatibility with existing userspace applications is handled by
selecting the XRGB format corresponding to the requested old RGB format.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The VSP1 stores the video pipelines' input (RPF) to output (WPF)
mappings in a WPF register. An RPF must never be associated with
multiple WPFs, even if all of those WPFs but one are unused, otherwise
the hardware won't function properly.
The driver doesn't ensure this correctly as it never clears the
mappings. An RPF used with one WPF and later with a different WPF will
lead to malfunction, as it will be associated with two WPFs. Clear the
mappings at stream off time to fix this.
Reported-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the subdev pointer directly to_vsp1_pipeline() macro instead of
casting from the subdev to the wpf object and back to the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The control value is currently stored in the SRU structure by the
control set handler and written to the hardware at stream on time,
making control set during streaming ineffective. Fix it by writing to
the registers from within the control set handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default value isn't set and defaults to 0, which isn't in the 1-6
min-max range. Fix it by setting the default value to 1.
This shoud have been caught when checking the control handler error
field at initialization time, but the check was missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When setting a control directly on a subdev node the VSP1 driver doesn't
guarantee that the device is powered on. This leads to crashes when the
control handlers writes to hardware registers. One easy way to fix this
is to ensure that the device gets powered on when a subdev node is
opened. However, this consumes power unnecessarily, as there's no need
to power the device on when setting formats on the pipeline.
Furthermore, control handler setup at entity init time suffers from the
same problem as the device isn't powered on easier.
Fix this by extend the entity base object to setup the control handler
automatically when starting the stream. Entities must then skip writing
to registers in the set control handler when not streaming, which can be
tested with the new vsp1_entity_is_streaming() helper function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modify the vsp1_device_get() function to return an error code instead of
a pointer to the VSP1 device, and use the return value in the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Video nodes created and initialized in the RPF and WPF init code paths
are never unregistered, and the related resources (videobuf alloc
context and media entity) never released.
Fix this by storing a pointer to the vsp1_video object in vsp1_entity
and calling vsp1_video_cleanup() from vsp1_entity_destroy(). This also
allows simplifying the init error code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
