When we take full hotplug to recover from EEH errors, PCI buses
could be involved. For the case, the child devices of involved
PCI buses can't be attached to IOMMU group properly, which is
caused by commit 3f28c5a ("powerpc/powernv: Reduce multi-hit of
iommu_add_device()").
When adding the PCI devices of the newly created PCI buses to
the system, the IOMMU group is expected to be added in (C).
(A) fails to bind the IOMMU group because bus->is_added is
false. (B) fails because the device doesn't have binding IOMMU
table yet. bus->is_added is set to true at end of (C) and
pdev->is_added is set to true at (D).
pcibios_add_pci_devices()
pci_scan_bridge()
pci_scan_child_bus()
pci_scan_slot()
pci_scan_single_device()
pci_scan_device()
pci_device_add()
pcibios_add_device() A: Ignore
device_add() B: Ignore
pcibios_fixup_bus()
pcibios_setup_bus_devices()
pcibios_setup_device() C: Hit
pcibios_finish_adding_to_bus()
pci_bus_add_devices()
pci_bus_add_device() D: Add device
If the parent PCI bus isn't involved in hotplug, the IOMMU
group is expected to be bound in (B). (A) should fail as the
sysfs entries aren't populated.
The patch fixes the issue by reverting commit 3f28c5a and remove
WARN_ON() in iommu_add_device() to allow calling the function
even the specified device already has associated IOMMU group.
Cc: <stable@vger.kernel.org> # 3.16+
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Similar to the previous commit which described why we need to add a
barrier to arch_spin_is_locked(), we have a similar problem with
spin_unlock_wait().
We need a barrier on entry to ensure any spinlock we have previously
taken is visibly locked prior to the load of lock->slock.
It's also not clear if spin_unlock_wait() is intended to have ACQUIRE
semantics. For now be conservative and add a barrier on exit to give it
ACQUIRE semantics.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel defines the function spin_is_locked(), which can be used to
check if a spinlock is currently locked.
Using spin_is_locked() on a lock you don't hold is obviously racy. That
is, even though you may observe that the lock is unlocked, it may become
locked at any time.
There is (at least) one exception to that, which is if two locks are
used as a pair, and the holder of each checks the status of the other
before doing any update.
Assuming *A and *B are two locks, and *COUNTER is a shared non-atomic
value:
The first CPU does:
spin_lock(*A)
if spin_is_locked(*B)
# nothing
else
smp_mb()
LOAD r = *COUNTER
r++
STORE *COUNTER = r
spin_unlock(*A)
And the second CPU does:
spin_lock(*B)
if spin_is_locked(*A)
# nothing
else
smp_mb()
LOAD r = *COUNTER
r++
STORE *COUNTER = r
spin_unlock(*B)
Although this is a strange locking construct, it should work.
It seems to be understood, but not documented, that spin_is_locked() is
not a memory barrier, so in the examples above and below the caller
inserts its own memory barrier before acting on the result of
spin_is_locked().
For now we assume spin_is_locked() is implemented as below, and we break
it out in our examples:
bool spin_is_locked(*LOCK) {
LOAD l = *LOCK
return l.locked
}
Our intuition is that there should be no problem even if the two code
sequences run simultaneously such as:
CPU 0 CPU 1
==================================================
spin_lock(*A) spin_lock(*B)
LOAD b = *B LOAD a = *A
if b.locked # true if a.locked # true
# nothing # nothing
spin_unlock(*A) spin_unlock(*B)
If one CPU gets the lock before the other then it will do the update and
the other CPU will back off:
CPU 0 CPU 1
==================================================
spin_lock(*A)
LOAD b = *B
spin_lock(*B)
if b.locked # false LOAD a = *A
else if a.locked # true
smp_mb() # nothing
LOAD r1 = *COUNTER spin_unlock(*B)
r1++
STORE *COUNTER = r1
spin_unlock(*A)
However in reality spin_lock() itself is not indivisible. On powerpc we
implement it as a load-and-reserve and store-conditional.
Ignoring the retry logic for the lost reservation case, it boils down to:
spin_lock(*LOCK) {
LOAD l = *LOCK
l.locked = true
STORE *LOCK = l
ACQUIRE_BARRIER
}
The ACQUIRE_BARRIER is required to give spin_lock() ACQUIRE semantics as
defined in memory-barriers.txt:
This acts as a one-way permeable barrier. It guarantees that all
memory operations after the ACQUIRE operation will appear to happen
after the ACQUIRE operation with respect to the other components of
the system.
On modern powerpc systems we use lwsync for ACQUIRE_BARRIER. lwsync is
also know as "lightweight sync", or "sync 1".
As described in Power ISA v2.07 section B.2.1.1, in this scenario the
lwsync is not the barrier itself. It instead causes the LOAD of *LOCK to
act as the barrier, preventing any loads or stores in the locked region
from occurring prior to the load of *LOCK.
Whether this behaviour is in accordance with the definition of ACQUIRE
semantics in memory-barriers.txt is open to discussion, we may switch to
a different barrier in future.
What this means in practice is that the following can occur:
CPU 0 CPU 1
==================================================
LOAD a = *A LOAD b = *B
a.locked = true b.locked = true
LOAD b = *B LOAD a = *A
STORE *A = a STORE *B = b
if b.locked # false if a.locked # false
else else
smp_mb() smp_mb()
LOAD r1 = *COUNTER LOAD r2 = *COUNTER
r1++ r2++
STORE *COUNTER = r1
STORE *COUNTER = r2 # Lost update
spin_unlock(*A) spin_unlock(*B)
That is, the load of *B can occur prior to the store that makes *A
visibly locked. And similarly for CPU 1. The result is both CPUs hold
their lock and believe the other lock is unlocked.
The easiest fix for this is to add a full memory barrier to the start of
spin_is_locked(), so adding to our previous definition would give us:
bool spin_is_locked(*LOCK) {
smp_mb()
LOAD l = *LOCK
return l.locked
}
The new barrier orders the store to the lock we are locking vs the load
of the other lock:
CPU 0 CPU 1
==================================================
LOAD a = *A LOAD b = *B
a.locked = true b.locked = true
STORE *A = a STORE *B = b
smp_mb() smp_mb()
LOAD b = *B LOAD a = *A
if b.locked # true if a.locked # true
# nothing # nothing
spin_unlock(*A) spin_unlock(*B)
Although the above example is theoretical, there is code similar to this
example in sem_lock() in ipc/sem.c. This commit in addition to the next
commit appears to be a fix for crashes we are seeing in that code where
we believe this race happens in practice.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Once again, we see
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:865: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:866: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:890: Error: attempt to move .org backwards
when compiling ppc:allmodconfig.
This time the problem has been caused by to commit 0869b6fd20
("powerpc/book3s: Add basic infrastructure to handle HMI in Linux"),
which adds functions hmi_exception_early and hmi_exception_after_realmode
into a critical (size-limited) code area, even though that does not appear
to be necessary.
Move those functions to a non-critical area of the file.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__early_init_mmu() does some things that are really only needed by the
boot cpu. On FSL booke, This includes calling
memblock_enforce_memory_limit(), which is labelled __init. Secondary
cpu init code can't be __init as that would break CPU hotplug.
While it's probably a bug that memblock_enforce_memory_limit() isn't
__init_memblock instead, there's no reason why we should be doing this
stuff for secondary cpus in the first place.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ocrdma does not report hw_ver when query_device is issued. This patch
adds a meaningful value to this field.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update the sli specific mailbox command request/response data
sturcures to fix endianness issues.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, driver obtains service level value from ah_attr->sl field.
However, this field is set to zero all the times from rdma-cm. This
patch allows create_ah to obtain service level from dev->sl.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
added struct sockaddr_storage to rdma_user_cm.h without also adding an
include for linux/socket.h to make sure it is defined. Systemtap
needs the header files to build standalone and cannot rely on other
files to pre-include other headers, so add linux/socket.h to the list
of includes in this file.
Fixes: ee7aed4528 ("RDMA/ucma: Support querying for AF_IB addresses")
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
GID change events need a refresh just like LID change events and several
others. Handle this the same as the others.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is a static checker fix. The static checker says that q_size comes
from the user and can be any 32 bit value. The call tree is:
--> ib_uverbs_create_cq()
--> c2_create_cq()
--> c2_init_cq()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix checkpatch warning:
WARNING: debugfs_remove(NULL) is safe this check is probably not required
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As with ARM the ARMv8 architecture provides a cycle counter which can be
used to provide a high resolution time for the joystick driver and
silence the build warning that results from not having a precise timer
on ARMv8, making allmodconfig and allyesconfig quieter.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If CONFIG_PM is not set:
drivers/hid/wacom_sys.c:1436: warning: ‘wacom_reset_resume’ defined but
not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If do_journal_release() races with do_journal_end() which requeues
delayed works for transaction flushing, we can leave work items for
flushing outstanding transactions queued while freeing them. That
results in use after free and possible crash in run_timers_softirq().
Fix the problem by not requeueing works if superblock is being shut down
(MS_ACTIVE not set) and using cancel_delayed_work_sync() in
do_journal_release().
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
There is an excessive space character between the word and the
period in the debug message. So delete it.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The macro E1000_success is meant to be E1000_SUCCESS. As the return
statement in the function is good as is, let's simply correct the
comment for this trivial matter.
Additionally E1000_ERR_HOST_INTERFACE_COMMAND is supposed to be
-E1000_ERR_HOST_INTERFACE_COMMAND.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds. The crash is due to pcr_ops being NULL.
This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.
init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:
1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
from smp_cpus_done().
2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().
3) Move init_hw_perf_events to a later initcall so that it we will be
sure to invoke pcr_arch_init() after all cpus are brought up.
Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nmi_cpu_busy() is a SMP function call that just makes sure that all of the
cpus are spinning using cpu cycles while the NMI test runs.
It does not need to disable IRQs because we just care about NMIs executing
which will even with 'normal' IRQs disabled.
It is not legal to enable hard IRQs in a SMP cross call, in fact this bug
triggers the BUG check in irq_work_run_list():
BUG_ON(!irqs_disabled());
Because now irq_work_run() is invoked from the tail of
generic_smp_call_function_single_interrupt().
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: bcmgenet: Wake-on-LAN and suspend fixes
This patch series fixes some mistakes that were introduced during the driver
changes adding support suspend/resume and Wake-on-LAN.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we configured the adapter to be a wake up source from
Wake-on-LAN, but we never actually woke up using Wake-on-LAN, we will
leave the adapter in MagicPacket matching mode, which prevents any other
type of packets from reaching the RX engine. Fix this by calling
bcmgenet_power_up() with GENET_POWER_WOL_MAGIC to restore the adapter
configuration in bcmgenet_resume().
The second problem we had was an imbalanced clock disabling in
bcmgenet_wol_resume(), the Wake-on-LAN slow clock is only enabled in
bcmgenet_suspend() if we configured Wake-on-LAN, yet we unconditionally
disabled the clock in bcmgenet_wol_resume().
Fixes: 8c90db72f9 ("net: bcmgenet: suspend and resume from Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we bring the interface down, phy_stop() will schedule the PHY state
machine to call our link adjustment callback. By the time we do so, we
may have clock gated off the GENET hardware block, and this will cause
bus errors to happen in bcmgenet_mii_setup():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
Fixes: 240524089d ("net: bcmgenet: only update UMAC_CMD if something changed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we properly suspend and resume the PHY device when we
enter low power modes. We had two calls to bcmgenet_mii_reset() which
will issue a software-reset to the PHY without using the PHY library,
get rid of them since they are completely bogus and mess up with the PHY
library state. Make sure that we reset the PHY library cached values
(link, pause and duplex) to allow the link adjustment callback to be
invoked when needed.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_hw_params() will read the hardware version and compare it
with the one we are getting from Device Tree. Due to the clock being
enabled too late, bcmgenet_set_hw_params() will cause bus errors since
the GENET hardware block is still gated off by the time
bcmgenet_set_hw_params() is called, this will also make us fail the
version check since we will read the value 0 from the hardware.
Fix this by requesting the clock before the first piece of code that
needs to access hardware register.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a long known problem with the netfront/netback interface: if the guest
tries to send a packet which constitues more than MAX_SKB_FRAGS + 1 ring slots,
it gets dropped. The reason is that netback maps these slots to a frag in the
frags array, which is limited by size. Having so many slots can occur since
compound pages were introduced, as the ring protocol slice them up into
individual (non-compound) page aligned slots. The theoretical worst case
scenario looks like this (note, skbs are limited to 64 Kb here):
linear buffer: at most PAGE_SIZE - 17 * 2 bytes, overlapping page boundary,
using 2 slots
first 15 frags: 1 + PAGE_SIZE + 1 bytes long, first and last bytes are at the
end and the beginning of a page, therefore they use 3 * 15 = 45 slots
last 2 frags: 1 + 1 bytes, overlapping page boundary, 2 * 2 = 4 slots
Although I don't think this 51 slots skb can really happen, we need a solution
which can deal with every scenario. In real life there is only a few slots
overdue, but usually it causes the TCP stream to be blocked, as the retry will
most likely have the same buffer layout.
This patch solves this problem by linearizing the packet. This is not the
fastest way, and it can fail much easier as it tries to allocate a big linear
area for the whole packet, but probably easier by an order of magnitude than
anything else. Probably this code path is not touched very frequently anyway.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_is_locked() always return false in uniprocessor configuration and therefore it
would be advise to repalce with WARN_ON_SMP().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-sleep:
PM / hibernate: avoid unsafe pages in e820 reserved regions
* pm-cpufreq:
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
* pm-cpuidle:
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
In the patch called "xen-netback: Turn off the carrier if the guest is not able
to receive" NAPI was descheduled when the carrier was set off. That's
not what most of the drivers do, and we don't have any specific reason to do so
as well, so revert that change.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it's possible to overwrite random pieces of unallocated memory during
kernel decompression, leading to machine resets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4YFS
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/efi
* Enforce CONFIG_RELOCATABLE for the x86 EFI boot stub, otherwise
it's possible to overwrite random pieces of unallocated memory during
kernel decompression, leading to machine resets.
Resolved Conflicts:
arch/x86/Kconfig
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Current upstream kernel hangs with mips and powerpc targets in
uniprocessor mode if SECCOMP is configured.
Bisect points to commit dbd952127d ("seccomp: introduce writer locking").
Turns out that code such as
BUG_ON(!spin_is_locked(&list_lock));
can not be used in uniprocessor mode because spin_is_locked() always
returns false in this configuration, and that assert_spin_locked()
exists for that very purpose and must be used instead.
Fixes: dbd952127d ("seccomp: introduce writer locking")
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
In the Makefile, qlcnic_minidump.o is included twice in the list of
object files linked into qlcnic.o.
This change removes the superfluous include.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for
port_t, card_status_t and card_t. Also, the names of the structs
are changed to drop the _t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects two cases and a
similar one detects the case for card_t.
@tn1@
type td;
@@
typedef struct { ... } td;
@script:python tf@
td << tn1.td;
tdres;
@@
coccinelle.tdres = td;
@@
type tn1.td;
identifier tf.tdres;
@@
-typedef
struct
+ tdres
{ ... }
-td
;
@@
type tn1.td;
identifier tf.tdres;
@@
-td
+ struct tdres
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Atari EtherNEC ROM port adapters in ne.c
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for
fr_hdr and pvc_device. Also, the names of the structs are changed to
drop the _t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case fr_hdr and a
similar one detects the case for pvc_device.
@tn1@
type td;
@@
typedef struct { ... } td;
@script:python tf@
td << tn1.td;
tdres;
@@
coccinelle.tdres = td;
@@
type tn1.td;
identifier tf.tdres;
@@
-typedef
struct
+ tdres
{ ... }
-td
;
@@
type tn1.td;
identifier tf.tdres;
@@
-td
+ struct tdres
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atmel_priv_ioctl.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
com20020_dev_t. Also, the name of the struct is changed to drop the
_t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for local_info_t.
Also, the name of the struct is changed to drop the _t, to make the
name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
