Now that we have completely moved from older USB-PHY drivers
to newer GENERIC-PHY drivers for PHYs available with USB controllers
on Exynos series of SoCs, we can remove the support for the same
in our host drivers too.
We also defer the probe for our host in case we end up getting
EPROBE_DEFER error when getting PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lately (with the use of uas / bulk-streams) we have been seeing several
cases where this error triggers (which should never happen).
Add some extra logging to make debugging these errors easier.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though a Set TR deq ptr command operates on a ring, and an endpoint
can have multiple rings, we can have only one Set TR deq ptr command pending.
When an endpoint with streams halts or is stopped to unlink urbs, there
will only be at most one ring active / one td being executed (the td
stopped_td points to).
So when we reset the endpoint (for a halt), or the stop command completes, we
will queue one Set TR deq ptr command at most, cancelled urbs on other stream
rings then the one being executed will have there trbs turned to nops, and
once the hcd gets around to execute that stream ring they will be simply
skipped.
So the SET_DEQ_PENDING flag in the endpoint is sufficient protection against
starting the endpoing before all stream rings are cleaned up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the stream for which the command was intended has been freed in the
mean time. This ensures that things start rolling again after an unlink / halt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_queue_new_dequeue_state is the only caller of queue_set_tr_deq
and queue_set_tr_deq checks for SET_DEQ_PENDING, where as
xhci_queue_new_dequeue_state sets it which is inconsistent.
Simply fold the 2 into one is a nice cleanup and fixes the inconsistency.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
V2 - Restart polling (which will restart the timer) for the shared
HCD in xhci_resume().
xhci_suspend() will stop the primary HCD's root hub timer, but leaves
the shared HCD's timer running. This change adds stopping of the
shared HCD timer.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple reasons for this:
1) This fixes a missing check for xhci_alloc_command failing in
xhci_handle_cmd_stop_ep()
2) This adds a warning when we cannot set the new dequeue state because of
xhci_alloc_command failing
3) It puts the allocation of the command after the sanity checks in
queue_set_tr_deq(), avoiding leaking the command if those fail
4) Since queue_set_tr_deq now owns the command it can free it if queue_command
fails
5) It reduces code duplication
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If something goes wrong in our communication with an uas device we may get
a response iu in reaction to a cmnd, rather then a status iu. In this case
propagate an error upwards, rather then logging a bogus iu message.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of doing:
uas_log_cmd_state(cmnd, __func__)
scmd_printk(KERN_ERR, cmnd, "error doing foo %d\n", err)
On error, resulting in 2 log calls for a single error, make uas_log_cmd_state
take a status code, and change calls like the above to:
uas_log_cmd_state(cmnd, "error doing foo", err)
Also change various sanity checks (which should never trigger) from:
"scmd_printk(KERN_ERR, cmnd, "sanity foo failed\n")" to calling the new
uas_log_cmd_state(), so that when they do trigger we get more info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've removed all hack from the driver for pre-production hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've access to a number of different uas devices now, and none of them use
old style sense urbs. The only case where these code-paths trigger is with
the asm1051 and there they do the wrong thing, as the asm1051 sends 8 bytes
status iu-s when it does not have any sense data, but uses new style
sense iu-s regardless, as can be seen for scsi cmnds where there is sense
data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was only used to sanity check against completing the same cmnd twice,
but that is the case we're likely operating on free-ed memory, and doing
sanity checks on free-ed memory is not really helpful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_print_command to print commands during errors, rather then printing
the rather meaningless pointer to the command.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for both type of cancellation codes for sense and data urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limit the no-streams case to speeds less then USB_SPEED_SUPER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of uas_pre_reset is to:
1) Stop any new commands from being submitted while an externally triggered
usb-device-reset is running
2) Wait for any pending commands to finish before allowing the usb-device-reset
to continue
The purpose of uas_suspend is to:
2) Wait for any pending commands to finish before suspending
This commit fixes races in both paths:
1) For 1) we use scsi_block_requests, but the scsi midlayer calls queuecommand
without holding any locks, so a queuecommand may already past the midlayer
scsi_block_requests checks when we call it, add a check to uas_queuecommand
to fix this
2) For 2) we were waiting for all sense-urbs to complete, there are 2 problems
with this approach:
a) data-urbs may complete after the sense urb, so we need to check for those
too
b) if a sense-urb completes with a iu id of READ/WRITE_READY a command is not
yet done. We submit a new sense-urb immediately in this case, but that
submit may fail (in which case it will get retried by uas_do_work), if this
happens the sense_urbs anchor may become empty while the cmnd is not yet
done
Also unblock requests on timeout, to avoid things getting stuck in that case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all urbs we've allocated are necessarily also submitted, non-submitted
urbs will not be free-ed by their completion handler. So we need to free
them manually.
There are 2 scenarios where this can happen:
1) We have failed to submit some urbs at abort / disconnect
2) When running over usb-2 we may have never tried to submit the data urbs
when completing the scsi cmnd, because we never got a READ/WRITE_READY iu
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not keep references around to a cmnd which is under error handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not strictly necessary for the cmd urb to have a reference to the
cmnd, and without this reference it becomes easier to drop all references to
a cmnd on an abort.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've the same info doubled in both the inflight list and the cmnd array,
drop the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data urbs are all killed before calling zap_pending, and their completion
handler should have cleared their inflight flag.
Do not 0 the data inflight flags, and add a check for try_complete succeeding,
as it should always succeed when called from zap_pending.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the whole dance with first moving cmnds to a dead-list. The resetting
flag ensures that no new cmds / urbs will be submitted, and that any urb
completions are short-circuited without trying to complete the scsi cmnd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we no longer drop our lock to unlink the data urbs, we can simply
free them on completion, making their handling consistent with the other urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for all the trickery with dropping the lock, we can
simply reference the urbs while we hold the lock to ensure the urbs don't
disappear beneath us, and do the actual unlink (+ unreference) after we've
dropped the lock.
This also fixes a race where we may loose of cmnd ownership to the scsi
midlayer without holding the lock due to the midlayer re-claiming ownership
through an abort (which will be handled by a future patch in this series).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status urb should not complete before the command has been submitted, nor
should we get a second status urb for the same tag after a IU_ID_STATUS.
Data urbs should not complete before the command has been submitted, but may
complete after the IU_ID_STATUS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using scsi_host_find_tag with tags returned by the device is unsafe for
multiple reasons:
1) It returns tags->rqs[tag], which may be non NULL even when the cmnd is
not owned by us
2) It returns tags->rqs[tag], without holding any locks protecting it
3) It returns tags->rqs[tag], without doing any boundary checking
Instead keep our own list which maps tags -> inflight cmnds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out the mapping of scsi-tags -> uas-tags/stream-ids to a helper function
so that there is a single place where this "magic" happens.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make sure we always hold the lock when setting / checking resetting
- Check resetting before checking urb->status
- Add missing check for resetting to uas_data_cmplt
- Add missing check for resetting to uas_do_work
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are various bug reports about oopses / hangs with the uas driver,
which all point to the abort-command and logical-unit-reset (task-management)
error handling paths.
Getting these right is very hard, there are quite a few corner cases, and
testing is almost impossible since under normal operation these code paths
are not used at all.
Another problem is that there are also some cases where it simply is not clear
what to do at all. E.g. over usb-2 multiple outstanding commands share the same
endpoint. What if a command gets aborted while its sense urb is half way
through completing (so some data has been transfered but not all). Since the
urb is not yet complete we don't know if the sense urb is actually for this
command, or for one of the other oustanding commands. If it is for one of the
other commands and we cancel it, then we end up in an undefined state. But if
it is actually for the command we're aborting, and the abort succeeds, then it
may never complete...
This exact same problem applies to logical unit resets too, if there are
multiple luns, then commands outstanding on both luns share the sense
endpoint. If there is only a single lun, then doing a logical unit reset is
little better then doing a full usb device reset.
So summarizing because:
1) abort / lun-reset is very tricky to get right
2) Not being able to test the tricky code, which means it will have bugs
3) This being a code path which under normal operation will never happen,
so being slow / sub-optimal here is not really an issue
4) Under error conditions we will still be able to recover through usb
device resets.
5) This may be a bit slower in some cases, but this is actually faster in
cases where the bridge ship has locked up, which seems to be the most
common error case sofar.
This commit removes the abort / lun-reset error handling paths, and also the
taks-mgmt code since those are the only 2 task-mgmt users. Leaving only the
(tested and testable) usb-device-reset error handling path in place.
Note I realize that this is somewhat of a big hammer, but currently people
are seeing very hard to debug oopses with uas. First let focus on making uas
work reliable, then we can later look into adding more fine grained error
handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most ASM1051 based devices, this one has unfixable issues with uas too.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on some architecture spin_is_locked() always return false in
uniprocessor configuration and therefore it would be advise
to replace with lockdep_assert_held().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip OHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the glue code required to ensure the on-chip EHCI
controller works on STi consumer electronics SoC's from STMicroelectronics.
It mainly manages the setting and enabling of the relevant clocks and manages
the reset / power signals to the IP block.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource to simplify error handling in the probe
function and to get rid of some boilerplate in the remove function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL (Targeted Peripheral List) is used for targeted hosts
(non-PC hosts), and it can be used at USB OTG & EH certification
and some specific products which need white list.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update configuration for USB_OTG_WHITELIST, any targeted hosts
(non PC-hosts) can have TPL (Targered Peripheral List).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to On-The-Go and Embedded Host Supplement to the USB Revision
2.0 Specification, the targeted hosts (non-PC hosts) include both
embedded hosts and otg, and each targeted host product defines the
set of supported peripherals on a TPL (Targeted Peripheral List). So,
TPL should apply for both OTG and embedded host, and the otg support is
not a must for embedded host.
The TPL support feature will only be effect when CONFIG_USB_OTG_WHITELIST
has been chosen and hcd->tpl_support flag is set, it can avoid the enumeration
fails problem for the user who chooses CONFIG_USB_OTG_WHITELIST wrongly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2267089ea.
That commit causes more problem than fixes. Firstly, kfree()
should be called after usb_ep_dequeue() and secondly, the way
things are, we will try to dequeue a request that has already
completed much more frequently than one which is pending.
Cc: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.17
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
