Add H3LIS331DL, LIS331DL and LIS3LV02DL entries in st_accel_id_table
Fixes: 1e52fefc9b (iio: accel: Add support for the h3lis331dl accel)
Fixes: bbf5f037fa (iio: st_accel: support the LIS331DL sensor)
Fixes: 3acddf74f8 (iio: st-sensors: add support for lis3lv02d accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array startup_lookup static rather having it on the
stack saves 69 bytes. Add in missing int specifier to clean up a
checkpatch warning.
Before:
text data bss dec hex filename
10297 2800 128 13225 33a9 drivers/iio/adc/at91-sama5d2_adc.o
After:
text data bss dec hex filename
10140 2888 128 13156 3364 drivers/iio/adc/at91-sama5d2_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array init_data static rather having it on the
stack saves us a couple hundreds of bytes:
Before:
text data bss dec hex filename
3175 848 0 4023 fb7 drivers/iio/accel/da311.o
After:
text data bss dec hex filename
2860 936 0 3796 ed4 drivers/iio/accel/da311.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add newlines to the macro definitions and use a more common style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch warnings:
Prefer 'unsigned int' to bare use of 'unsigned
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LPS22HB, LPS25H, LPS331AP, LPS001WP
pressure sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Open drain should work fine with rising or high level IRQs,
this code was due to some misunderstanding on my part.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add open drain support in order to share requested IRQ line between
st_lsm6dsx device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While the INA226 has a conversion ready flag (CVRF) in the R/W Mask/Enable
register with read-to-clear semantics, the corresponding bit of the INA219
(CNVR) is part of the bus voltage register. The flag is cleared by reading
the power register.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for the external hardware trigger on pin ADTRG,
integrated the three possible edges into the driver
and created buffer management for data retrieval
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add of_match_table and point it to a list of compatible device tree
device id's.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Include datasheet links, add i2c_device_id entries, and update
kconfig help for compatible HDC10xx devices: HDC1000, HDC1008,
HDC1010, HDC1050, and HDC1080.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add proper support for L3GD20H gyroscope sensor. In particular:
- use L3GD20H as device name instead of L3GD20
- fix available full scales
- fix available sample frequencies
Note that the original patch listed first below introduced broken support for
this part. The second patch drops the support as it didn't work.
This new patch brings in working support.
Fixes: 9444a300c2 (IIO: Add support for L3GD20H gyroscope)
Fixes: a065771641 ("iio:gyro: bug on L3GD20H gyroscope support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the BOSC0200 ACPI device id used on some x86 tablets.
note driver_data is not set to a specific model, driver_data is not
used anyways (instead detection is done on the chip_id reg) and the
2 tablets with a BOSC0200 ACPI device id I've have 2 different chips,
one has a BMA250E, the other a BMA222E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
-----BEGIN PGP SIGNATURE-----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=2fJI
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.13 cycle.
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
SPI bus is never generating error during transfer, so to check if
a chip is correctly connected on a SPI bus we enforce whoami check
to be correct. In this way we can assure SPI probe is failing if
there is no chip connected.
Note that this is really papering over boards that claim the device
is there when it isn't. Not a bad thing to cope with, but not
necessarily stable material.
Fixes: cec0154556 ("iio: inv_mpu6050: Check WHO_AM_I register on probe")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Building a kernel with my configuration failed with:
> drivers/built-in.o: In function `hid_sensor_setup_batch_mode': staging/drivers/iio/common/hid-sensors/hid-sensor-trigger.c:104: undefined reference to `iio_buffer_set_attrs'
which is fixed by this patch.
Signed-off-by: Alexander Wuerstlein <arw@arw.name>
Fixes: 138bc7969c ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add buffer_impl.h as buffer.h was split into interface for using and
for internals. Without this industrialio-buffer-dmaengine.c fails
to compile.
Fixes:
commit 33dd94cb97 ("iio:buffer.h - split
into buffer.h and buffer_impl.h")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add buffer_impl.h as buffer.h was split into interface for using and
for internals. Without this industrialio-buffer-dma.c fails
to compile.
Fixes:
commit 33dd94cb97 ("iio:buffer.h - split
into buffer.h and buffer_impl.h")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While using GPIO library API we might get into troubles in the future,
because we can't rely on label name in the driver since vendor firmware
might provide any GPIO pin there, e.g. "reset", and even mark it in _DSD
(in which case the request will fail).
To avoid inconsistency and potential issues we have two options:
a) generate GPIO ACPI mapping table and supply it via
acpi_dev_add_driver_gpios(), or
b) just pass NULL as connection ID.
The b) approach is much simpler and would work since the driver relies
on GPIO indices only. Moreover, the _CRS fallback mechanism, when
requesting GPIO, is going to be stricter, and supplying non-NULL
connection ID when neither _DSD, nor GPIO ACPI mapping is present, will
make request fail.
See
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio.git/commit/?h=for-next&id=ed7fcf1ed5ea4ea01243995ae085757a77cf0f3e for more background.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add validate function to be use to use the correct trigger.
Add an attribute to configure device mode like for quadrature and
enable modes
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
