Add IRQ coalescing to sata_mv (off by default).
This feature can reduce total interrupt overhead for RAID setups
in some situations, by deferring the interrupt signal until one or both of:
a) a specified io_count (completed SATA commands) is achieved, or
b) a specified time interval elapses after an IO completion.
For now, module parameters are used to set the irq_coalescing_io_count
and irq_coalescing_usecs (timeout) globally. These may eventually
be supplemented with sysfs attributes, so that thresholds can be set
on-the-fly and on a per-chip (or even per-host_controller) basis.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Various cosmetic changes in preparation for the IRQ coalescing feature.
Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
platform_get_irq() can return -ENXIO, but since 'irq' is an
unsigned int, it does not show when the IRQ resource wasn't found.
Make irq an int so that we can use a single variable to test the
platform_get_irq() return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to Alan:
>and yes the EFAR does UDMA66.
mwdma:
>Yep - wrong comment. The EFAR is a sort of clone of the PIIX and I
>copied the comment while EFAR don't appear to have copied the
>limitation
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As noted by Alan:
>Your suspicions are correct here btw - the device can only do MWDMA1 and
>MWDMA2 (much like some PIIX devices)
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is initially needed to work around NCQ errata,
whereby the READ_LOG_EXT command sometimes fails
when issued in the traditional (sff) fashion.
Portions of this code will likely be reused for
implementation of the target mode feature later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.
When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata! So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so that it doesn't miss any protocols. Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.
This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This also gets rid of any need for mv_mode_filter().
Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register. For safety, we clear that
bit again when switching back to EDMA mode.
To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes. This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to turn off intx explicitly on msi enable. This is
automatically handled by pci. Drop it.
This might be needed on machines if the BIOS turns intx off during
boot. However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller. However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove redundant code left over from the earlier patch 04/07.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma(). It must then also be invoked
from mv_hardreset() and from mv_port_start().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier. This may also help with problems
reported by Jens on the PPC platform.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
commit b1c4a9dddf ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR> CR: 24024042 XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced when we switched to using the core
pci_set_power_state(). The chip seems to need the state to be written
over and over again until it sticks, so we do that.
Note that the code is a bit blunt, without timeout, etc... but that's
pretty much because I put back in there the code exactly as it used to
be before the regression. I still add a call to pci_set_power_state()
at the end so that ACPI gets called appropriately on x86.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Raymond Wooninck <tittiatcoke@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In two dca files copyright and license headers are missing.
This patch adds them there.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to reconfigure vlan-ids during an i/f down/up cycle
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every USB transfer buffer has to be allocated individually by kmalloc.
Impact: bugfix, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Kolja Waschk <kawk@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier. This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.
Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up. On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.
The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode. When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.
Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval. An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was
changed.
This revises it for this change.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tulip is currently doing request_irq before it has done its
initialization. This is usually not a problem because it hasn't
enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler
when registering the interrupt as a sanity check.
This can result in a NULL ptr dereference, so call tulip_init_ring
before request_irq, and add a free_ring function to do the freeing
now shared with tulip_close.
Tested with a shell loop running ifup, ifdown in a loop a few hundred
times with DEBUG_SHIRQ on.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make NetworkManager work with virtio_net
For now the semantics are simple: There is always carrier.
This allows a seamless experience with e.g., qemu/kvm
where NetworkManager just configures and sets up
everything automagically.
If/when a generally agreed-upon way to control
carrier on/off in the emulator/hypervisor level
emerges, it will be trivial to extend the driver
to support that too, but for now even this 2-liner
makes user experience that much better.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects an omission from the following commit:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
The un-refactored code checked the link speed and duplex of
every slave on every pass; the refactored code did not do so.
The 802.3ad and balance-alb/tlb modes utilize the speed and
duplex information, and require it to be kept up to date. This patch
adds a notifier check to perform the appropriate updating when the slave
device speed changes.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode. This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.
Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully. Also update version to 1.9.3.
Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benet driver is now in the proper place in drivers/net/benet, so we
can remove the staging version.
Acked-by: Sathya Perla <sathyap@serverengines.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
