Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers may not have a LED signal line, whereas the register
updates to control the non-existent LED can be relatively time consuming.
Add a quirk to disable LED control.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On cmd12 (STOP_TRANSMISSION), STM32 sdmmc variant needs to set
cmdstop bit in command register. The CPSM ("Command Path State Machine")
treats the command as a Stop Transmission command and signals
abort to the DPSM ("Data Path State Machine").
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With some eMMC devices, there is still issues with the new phase
settings. Enabling signal resampling seems to solve the problem
for these.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Align the default Core and Tx phase with the SoC vendor tree.
Even if the Tx phase is different from what the documentation
recommends, it seems to provide better results.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host controllers on TI's AM654 SOCs are not compatible with
the phy and consumer model of the sdhci-of-arasan driver. It turns out
that for optimal operation at higher speeds, a special tuning procedure
needs to be implemented which involves configuration of platform
specific phy registers.
Therefore, branch out to a new sdhci_am654 driver and add the phy
register space with all phy configurations to it. Populate AM654
specific callbacks to sdhci_ops and add SDHCI_QUIRKS wherever
applicable.
Only add support for upto High Speed for SD card and upto DDR52 speed
mode for eMMC. Higher speeds will be added in subsequent patches.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added sdhci_msm_restore_sdr_dll_config() function is only called
if CONFIG_PM is enabled:
drivers/mmc/host/sdhci-msm.c:1050:12: error:
'sdhci_msm_restore_sdr_dll_config' defined but not used
[-Werror=unused-function]
Better remove the incorrect #ifdef altogether and just use __maybe_unused,
which is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mmc/host/alcor.c: In function 'alcor_data_set_dma':
drivers/mmc/host/alcor.c:124:12: warning:
variable 'len' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/alcor.c:648:15: warning:
variable 'clock_out' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a spelling mistake in a pr_warn message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx USB parent device, has logic to detect when a card is inserted
into the card slot. Although, the logic can't detect when a card is
removed. This makes things a bit tricky, which is why the current method is
simply to turn on MMC_CAP_NEEDS_POLL during probe.
Using MMC_CAP_NEEDS_POLL means lots of energy being wasted, as the mmc host
becomes runtime resumed frequently by the mmc core, while it polls for new
cards being inserted.
To address this problem, let's start relying on that the rtsx USB driver
runtime resumes its child device, which is the rtsx_usb_sdmmc device, when
it detects that a new card being inserted.
This means dropping MMC_CAP_NEEDS_POLL from being set during probe. Instead
let's implement a ->runtime_resume() callback to schedule a detect work and
to set MMC_CAP_NEEDS_POLL. In this way, polling is enabled as long as there
is card inserted, thus we can rely on the mmc core to detect also when the
card becomes removed.
Furthermore, to avoid polling forever after a card has been removed, let's
implement a ->runtime_suspend() callback and make it clear
MMC_CAP_NEEDS_POLL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The current implementation uses the runtime PM autosuspend feature with a
default timeout set to 50ms. This really doesn't makes sense, as it's a USB
driven host device, which needs it rtsx USB device (parent device) to be
runtime resumed to provide power to the card.
In practise, using the autosuspend or any async runtime PM suspend method,
means unnecessary delaying the host device and thus the parent, to be
runtime suspended when a card is removed/powered off. For this reasons,
let's simply drop the support for runtime PM autosuspend and tell the mmc
core to use synced runtime PM suspend methods, via setting
MMC_CAP_SYNC_RUNTIME_PM during probe.
Moreover, as the mmc core nowadays deploys runtime PM reference counting of
the mmc host device, convert ->set_ios() to use the more lightweight
pm_runtime_get_noresume() and pm_runtime_put_noidle() APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
In case the card has been powered off, it seems silly to continue to allow
the led to be updated. Instead let's forbid that, as it enables us to
prevent runtime resuming the device and thus avoids wasting energy.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
To allow mmc host drivers to inform the mmc core about rather using
pm_runtime_put_sync_suspend() instead of pm_runtime_put_autosuspend(),
let's introduce MMC_CAP_SYNC_RUNTIME_PM.
This is especially useful for those mmc host drivers that don't benefit
from using the runtime PM autosuspend feature. Typically this is those that
relies on parent devices to power the card via runtime PM, like some USB
host drivers for example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com>
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver provides support for Alcor Micro AU6601 and AU6621
SD/MMC controller.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the mmc max-frequency device property for Intel BYT-based
host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All host drivers are converted to look up GPIO descriptors
from device tree, ACPI or machine descriptor tables, so now
we can delete the legacy GPIO handling using hardcoded GPIO
numbers from the kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After converting the PXA driver to use GPIO descriptors for
card detect and write protect it is relatively simple to
convert it to also use a descriptor for getting the optional
power control GPIO.
The polarity inversion flag can also go away from the platform
data since this is indicated in the GPIO machine descriptor
table.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This deletes the code dealing with handling card detect
and write protect passed in as platform data and makes
the host rely on just GPIO descriptors.
The card read only inversion flag has to be kept around
for now, as the core cannot handle the inversion flags
on the descriptors yet.
Since we can now rely on the descriptors to have the
right polarity, we set the "override_active_level" to
false in mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the code path for the PXAMCI hostso that
it can retrieve GPIO descriptors rather than use the
global GPIO numberspace for GPIO lines. If the GPIO
descriptor is present, it will take precedence and get
used in place of the platform data GPIO number.
We move the code around a bit so we request the card
detect first and the write protect second.
We keep the code setting the host flag for the write
protect polarity inversion semantics since the slot
GPIO core needs to be refactored to deal with this
before we can get rid of this.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the S3CMCI driver just use
slot GPIO with descriptors instead of passing around the
global GPIO numbers that we want to get rid of.
Getting the names of the GPIO chips into the machine
descriptor tables was a bit of a challenge but I think
I have them right.
The platform data supports passing in inversion flags, but
no platform is using them, and it is highly unlikely
that we will add more, so drop them. The long term plan
is to let the inversion flags on the GPIO machine
descriptor do the job.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO MMC driver was passing global GPIO numbers around for
card detect. It turns out only one single board in the kernel
was actually making use of this feature so it is pretty easy
to convert the driver to use only GPIO descriptors.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the SPI MMC driver to use GPIO descriptors internally
and just look those up using the standard slot GPIO
functions mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Make sure to request index 0 and 1 in accordance with the
SPI MMC DT binding, and add the same GPIOs in machine
descriptor tables on all boards that use SPI MMC in
board files.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Hartley Sweeten <hsweeten@visionengravers.com> # Vision EP9307
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_mx_mmc_register_clks() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was a SoC issue on LX2160A Rev1.0.
eSDHC_DLLCFG1[DLL_PD_PULSE_STRETCH_SEL] must be set to 0 to
get 4 delay cells in the pulse width detection logic for eMMC
HS400 mode. Otherwise it would cause unexpected HS400 issue.
This patch is to clear this bit always for affected SoC when
reset for all, since this bit doesn't affect other speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are timing violations in case of few division ratio options
are selected for card clock frequency. prescaler*divisor options
/3,/5,/6,/7,/9,/10,/11,/13,/14 and /15 are not available in LX2
Rev1.0. prescaler*divisor options /4,/8 and /12 only available in
LX2 Rev1.0. Applicable only for HS400 mode. so by add the erratum
A011334 support to limit the prescaler*divisor in LX2 REV1.0
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC controllers need specific settings for HS400 mode before the
speed mode can be switched to DDR mode, during the HS400 initialization
sequence. For that reason, let's introduce a new host callback,
->hs400_prepare_ddr() and invoked it just before switching to DDR mode.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_execute_tuning() function has assignment of
private pointers multiple times. Remove the redundant assignment.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TRM (SPRUIC2C - January 2017 - Revised May 2018 [1]) forbids
assertion of data reset while tuning is happening. Implement a
platform specific callback that takes care of this condition.
[1] http://www.ti.com/lit/pdf/spruic2 Section 25.5.1.2.4
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As reported by Aaro, the JZ4740 MMC driver throws a warning when the kernel
is built without preemption (CONFIG_PREEMPT_NONE=y).
[ 16.461094] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 567 host->next_data.cookie 568
[ 16.473120] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 568 host->next_data.cookie 569
[ 16.485144] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 569 host->next_data.cookie 570
[ 16.497170] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 570 host->next_data.cookie 571
The problem seems to be related to how pre_req/post_req is implemented.
Currently, it seems the driver expects jz4740_mmc_prepare_dma_data() to be
called with monotonically increasing host_cookie values, which is wrong.
Moreover, the implementation is overly complicated, keeping track of
unneeded "next cookie" state.
So, instead of attempting to fix the current pre_req/post_req
implementation, this commit refactors the driver, dropping the state,
following other drivers such as dw_mmc and sdhci.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refer to "4.15 set block count command" of sd specification:
Host needs to issue CMD12 if any error is detected in
the CMD18 and CMD25 operations.
In sbc case, the data->stop is fill by framework.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some variants (namely Renesas SDHI) have bits in the STATS and IRQ_MASK
registers which are 'always 1' and should be written as such. Introduce
a seperate mask for this and apply it whenever such a register is
written.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Renesas BSP confirms that H3 ES1.x and M3-W ES1.[012] do not
properly support HS400. Add a quirk to indicate this and disable HS400
in the MMC capabilities if the quirk is set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was though all ES revisions of H3 and M3-W SoCs required the
TMIO_MMC_HAVE_4TAP_HS400 flag. Recent datasheet updates tells us this is
not true, only early ES revisions of the SoC do.
Since quirk matching based on ES revisions is now used to handle the
flag it's possible to align all Gen3 compatibility properties. This will
allow later ES revisions of H3 and M3-W to use the correct 8-tap HS400
mode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest datasheet makes it clear that not all ES revisions of the H3 and
M3-W have the 4-tap HS400 mode quirk, currently the quirk is set
unconditionally for these two SoCs. Prepare to handle the quirk based on
SoC revision instead of compatibility value by using soc_device_match()
and set the TMIO_MMC_HAVE_4TAP_HS400 flag explicitly.
The reason for adding a new quirks struct instead of just a flag is that
looking ahead it seems more quirks needs to be handled in a SoC revision
basis.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial value of the interrupt mask register may be different from
the H/W manual at the startup of the kernel by setting from the
bootloader. Since the error interrupts may be unmasked, the driver sets
initial value.
The initial value is only known for R-Car Gen2 and Gen3 platforms so
limit the initialization to those platforms.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD / MMC did not operate properly when suspend transition failed.
Because the SCC was not reset at resume, issue of the command failed.
Call the host specific reset function and reset the hardware in order to
add reset of SCC. This change also fixes tuning on some stubborn cards
on Gen2.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On runtime power management resume, the host clock needs to be
enabled before calling tmio_mmc_reset. If the mmc device has a power
domain entry, the host clock is enabled via genpd_runtime_resume,
running before tmio_mmc_host_runtime_resume. If the mmc device has no
power domain entry, however, genpd_runtime_resume is not called. This
patch changes tmio_mmc_host_runtime_resume to enable the host clock
before calling tmio_mmc_reset.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user was converted to fill a sbc command which is the proper
way to do it because of AutoCMD23 feature of some hosts.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case dmaengine_prep_slave_sg fails we need to call dma_unmap_sg.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two variables len within bcm2835_prepare_dma. So rename the
result of dma_map_sg to sg_len. While we are at this add a bail out to
simplify the following change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's better to make sure that the timeout work is really terminated
before calling mmc_request_done.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two accesses on the data requests which are not protected by
the mutex. So fix this accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to release the slave DMA channel during driver unload.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the i.MX SDHCI driver just use
slot GPIO with descriptors instead of passing around the global
GPIO numbers that we want to get rid of.
As it turns out, just one single board is using the platform
data to pass in GPIOs numbers for CD and WP, so we augment this
to use a machine descriptor table instead.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power GPIO line is passed with inversion flags and all from
the platform data. Switch to using an optional GPIO descriptor and
use this to switch the power.
Augment the only boardfile to pass in the proper "power" descriptor
in the GPIO descriptor machine table instead.
As the GPIO handling is now much simpler, we can cut down on some
overhead code.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.
Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of string pointers in the MMC slot GPIO context is
pretty dubious, allocating some 2*len extra bytes for each
label of the ro and wp pins.
Tidy this up using kasprintf() with dynamic allocation of
labels for these strings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On few SDHCI-MSM controllers, the host controller's clock tuning
circuit may go out of sync if controller clocks are gated which
eventually will result in data CRC, command CRC/timeout errors.
To overcome this h/w limitation, the DLL needs to be re-initialized
and restored with its old settings once clocks are ungated.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing data command CRC error handling is non-standard and does not work
with some Intel host controllers. Specifically, the assumption that the host
controller will continue operating normally after the error interrupt,
is not valid. Change the driver to handle the error in the same manner
as a data CRC error, taking care to ensure that the data line reset is
done for single or multi-block transfers, and it is done before
unmapping DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelist R8A77990 E3 SoC in the SDHI driver. The SDHI core
present in the SoC is an 8tap variant of the Gen3 SDHI core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The manual does not contain information that a wait is needed in the
tuning process, this might be a leftover from early development.
Removing the wait don't have any effect on operation so delete the wait
to shorten the initialization time.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[Niklas: fixup commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver sets an incorrect clock and depends on the clock driver
knowledge of this incorrect setting to still set a 200Mhz SDn clock.
Instead of spreading the workaround between the two drivers the clock
driver should be made aware of the ES versions where the special clock
handling is needed no need to keep this workaround in the SDHI driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK() macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function sdhci_allocate_bounce_buffer() always return zero at
present, so there's no need to have a return value, that will also make
error path easier.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHI/MMC controller in the RZ/A2 is almost the same as R-Car gen3, but
with some minor differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On our AT91SAM9260 board we use the same sdio bus for wifi and for the
sd card slot. This caused the atmel-mci to give the following splat on
the serial console:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44
Modules linked in:
CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14
Hardware name: Atmel AT91SAM9
[<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
[<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4)
[<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24)
[<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44)
[<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc)
[<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164)
[<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0)
[<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330)
[<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310)
[<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac)
[<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118)
[<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118)
[<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34)
---[ end trace 594371ddfa284bd6 ]---
This is:
WARN_ON(host->cmd);
This was fixed on our board by letting atmci_request_end determine what
state we are in. Instead of unconditionally setting it to STATE_IDLE on
STATE_END_REQUEST.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit removes the unnecessary of-node check since the
dw_mci_bluefield_match[] structure has only one entry.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3f ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3f ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Andrzej Zaborowski <balrogg@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Problem:
The card detect IRQ does not work with modern BIOS (that want
to use _DSD to provide the card detect GPIO to the driver).
Details:
The mmc core provides the mmc_gpiod_request_cd() API to let host drivers
request the gpio descriptor for the "card detect" pin.
This pin is specified in the ACPI for the SDHC device:
* Either as a resource using _CRS. This is a method used by legacy BIOS.
(The driver needs to tell which resource index).
* Or as a named property ("cd-gpios"/"cd-gpio") in _DSD (which internally
points to an entry in _CRS). This way, the driver can lookup using a
string. This is what modern BIOS prefer to use.
This API finally results in a call to the following code:
struct gpio_desc *acpi_find_gpio(..., const char *con_id,...)
{
...
/* Lookup gpio (using "<con_id>-gpio") in the _DSD */
...
if (!acpi_can_fallback_to_crs(adev, con_id))
return ERR_PTR(-ENOENT);
...
/* Falling back to _CRS is allowed, Lookup gpio in the _CRS */
...
}
Note that this means that if the ACPI has _DSD properties, the kernel
will never use _CRS for the lookup (Because acpi_can_fallback_to_crs()
will always be false for any device hat has _DSD entries).
The SDHCI driver is thus currently broken on a modern BIOS, even if
BIOS provides both _CRS (for index based lookup) and _DSD entries (for
string based lookup). Ironically, none of these will be used for the
lookup currently because:
* Since the con_id is NULL, acpi_find_gpio() does not find a matching
entry in DSDT. (The _DSDT entry has the property name = "cd-gpios")
* Because ACPI contains DSDT entries, thus acpi_can_fallback_to_crs()
returns false (because device properties have been populated from
_DSD), thus the _CRS is never used for the lookup.
Fix:
Try "cd" for lookup in the _DSD before falling back to using NULL so
as to try looking up in the _CRS.
I've tested this patch successfully with both Legacy BIOS (that
provide only _CRS method) as well as modern BIOS (that provide both
_CRS and _DSD). Also the use of "cd" appears to be fairly consistent
across other users of this API (other MMC host controller drivers).
Link: https://lkml.org/lkml/2018/9/25/1113
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: f10e4bf663 ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the lock in mmc_blk_data that is only used through a pointer
in struct mmc_queue and to protect fields in that structure with
an actual lock in struct mmc_queue.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmc uses the block layer struct request pointer to indirect their own
lock to the mmc_queue structure, given that the original lock isn't
reachable outside of block.c. Add a lock pointer to struct mmc_queue
instead and stop overriding the block layer lock which protects fields
entirely separate from the mmc use.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge three functions initializing the queue into a single one, and drop
an unused argument for it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors
-----BEGIN PGP SIGNATURE-----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=/4yi
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors"
* tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (129 commits)
mmc: mediatek: drop too much code of tuning method
mmc: mediatek: add MT8183 MMC driver support
mmc: mediatek: tune CMD/DATA together
mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail
mmc: mediatek: fill the actual clock for mmc debugfs
mmc: dt-bindings: add support for MT8183 SoC
mmc: uniphier-sd: avoid using broken DMA RX channel
mmc: uniphier-sd: fix DMA disabling
mmc: tmio: simplify the DMA mode test
mmc: tmio: remove TMIO_MMC_HAVE_HIGH_REG flag
mmc: tmio: move MFD variant reset to a platform hook
mmc: renesas_sdhi: Add r8a77470 SDHI1 support
dt-bindings: mmc: renesas_sdhi: Add r8a77470 support
mmc: mmci: add stm32 sdmmc variant
dt-bindings: mmci: add stm32 sdmmc variant
mmc: mmci: add stm32 sdmmc registers
mmc: mmci: add clock divider for stm32 sdmmc
mmc: mmci: add optional reset property
dt-bindings: mmci: add optional reset property
mmc: mmci: add variant property to not read datacnt
...
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAlvNQKgQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgps+8D/9Iy6YIeoPwN10gYsqIh0P2fS3wKzL3kiww
3vFsWO78PzgLxUlNmB7teLtNFc/R5mi8becZmAdvs9za5YFZk56o3Ifv1x+e+z00
VY1/gxhiJD6suLeJ6lECnERGDaiWOZVRMo2TE17vxYGW6GGaa0Ts6PUUXmpla1u5
WKctgt0Qv9WVNyiIdLdeHqzKJwsSSwNTt8fK7eFhy3x8e0CwJr+GtXckbbW3LFkY
lug0npsTli3EmEPMovZhd25SjZmTk5GTM+ADZQ7Tnv5KXoDWB9jn6TcCSAi3G+5d
5WUVwfnDyYJiH8qvlg5tRJ690muIy3xMOmpr7QBQ0YnR/LQ3EW+1CVfqD+qimgLH
TXzlREXQpBP3YlxSDS5nddz4o5z84GZmC9B/43ujPaZKIQ6eBXYdkmQH7tPtSugm
C6VGomR5tHotjxIiAsexh/5hAus+wW8bObKGTPTyINT0ub3XNclwCKLh26CgI9ie
WvbS9g3j/KPvu/7s6weZpgD+cks0YdWe/XdXXxiHwsGI9h3J2aJna5RQt1rKWDm5
wGCgbc/B8eSwiWx+GXlqdB9/Dy/bGXOnSTDnKpEVl1f5zNjeLwUKXbjvkMefWs4m
jEIcquuDETORY+ZYEfa5YbmS4Lhskr0kzMVTVkZ++81tAWpSCU9Xh3IHrR8TNpt+
J0oh0FHBDg==
=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Commit b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to
get/set array") changed the way GPIO values are passed to
gpiod_get/set_array_value() and friends. The new code introduced into
mmc_pwrseq_simple_set_gpios_value() incorrectly interpretes the 'value'
argument as a bitmap of GPIO values and assigns it directly to the
'values' bitmap variable passed to gpiod_set_array_value_cansleep()
instead of filling that bitmap with bits equal to the 'value' argument.
As a result, only member 0 of the array is handled correctly.
Moreover, wrong assumption is taken about the 'values' bitmap size not
exceding the number of bits of the 'value' argument type.
Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the tuning code is becoming more and more bloated, let's make the
set cmd/data delay to inline function to avoid too much redundant code.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8183 puts the tune register at top layer, so need add new code
to support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for MSDC IP which supports both data tune and async fifo, it can
tune cmd/data together. which can save the time and make the tune
result of CMD more stable as data line are 4bit or 8bit.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
as the mmc core layer has the mmc->actual_clock, so fill it
and drop msdc_host->sclk.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_rx is NULL when UNIPHIER_SD_CAP_BROKEN_DMA_RX quirk flag
is set. In this case, it should not set up DMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Once DMA is enabled, it is not possible to disable it because
uniphier_sd_dma_endisable() always sets the DMA_ENABLE_DMASDRW bit
regardless of the argument 'enable'. It should disable DMA when
'enable' is false.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_{rx,tx} represents the DMA capability of the platform.
Even if DMA is supported, there are cases where we want to use PIO,
for example, data length is short enough as commit 5f52c35529
("mmc: tmio: use PIO for short transfers") mentioned.
Regarding the hardware control flow, we are interested in whether DMA
is currently enabled or not, instead of whether the platform has the
DMA capability.
Hence, the several conditionals in tmio_mmc_core.c end up with
checking host->chan_{rx,tx} and !host->force_pio. This is not nice.
Let's flip the flag host->force_pio into host->dma_on.
host->dma_on represents whether the DMA is currently enabled or not.
This flag is set false in the beginning of each command, then should
be set true by tmio_mmc_start_dma() when the DMA is turned on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MMC_HAVE_HIGH_REG is confusing due to its counter-intuitive name.
All the TMIO MMC variants (TMIO MMC, Renesas SDHI, UniPhier SD) actually
have high registers. It is just that each of them implements its own
registers there. The original IP from Panasonic only defines registers
0x00-0xff in the bus_shift=1 review. The register area above them is
platform-dependent.
In fact, TMIO_MMC_HAVE_HIGH_REG is set only by tmio-mmc.c and used to
test the accessibility of CTL_SDIO_REGS. Because it is specific to
the TMIO MFD variant, the right thing to do is to move such registers
to tmio_mmc.c and delete the TMIO_MMC_HAVE_HIGH_REG flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CTL_RESET_SDIO register is specific to the TMIO MFD (tmio_mmc.c).
Add a new hook host->reset() for performing a platform-specific
reset sequence, and move CTL_RESET_SDIO over there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RZ/G1C (a.k.a. R8A77470) comes with three SDHI interfaces,
SDHI0 and SDHI2 are compatible with the R-Car Gen2 SDHIs, SDHI1
is compatible with R-Car Gen3 SDHIs and it can be used as
eMMC as well. This patch adds driver compatibility, and makes
sure both drivers get compiled for the R8A77470.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.
error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
Qcom has no specific resource to release, just mmci dmae resource.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on TI's AM654 devices.
Therefore, add a new compatible, AM654 specific quirks
and a new AM654 specific set_clock function which
configures the PHY in a sane way.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the driver passes platform data as a global structure
and uses the .data of of_device_id to pass the soc_ctl_map. To
make the implementation more flexible add a single data structure
that incorporates both of the above and pass it in the .data of
of_device_id.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when gate MSDC0_HCLK, access register will hang, even the MSDC driver
will never accessing register after HCLK was gated, but for safety, need
gate the bus_clk(which used to access register) too.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "fall-through:"
comment with a proper "fall through", which is what GCC is
expecting to find.
Addresses-Coverity-ID: 1373880 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the
"deliberate fall-through" comment with a proper "fall through"
at the bottom of the case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1373887 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384
fix checkpatch --strict issues:
-CHECK: Avoid using bool structure members because of possible alignment
issues - see: https://lkml.org/lkml/2017/11/21/384
-WARNING: Avoid using bool as bitfield. Prefer bool bitfields as
unsigned int or u<8|16|32>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the management of dma map/unmap into
mmci dma interfaces. This allows to simplify and prepare the next dma
callbacks for mmci host ops.
mmci_dma_unmap was called in mmci_data_irq & mmci_cmd_irq functions
and can be integrated in mmci_dma_data_error.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OMAP HSMMC driver has some elaborate and hairy handling for
passing GPIO card detect and write protect lines from a boardfile
into the driver: the machine defines a struct omap2_hsmmc_info
that is copied into struct omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() in arch/arm/mach-omap2/hsmmc.c.
However the .gpio_cd and .gpio_wp fields are not copied from
omap2_hsmmc_info to omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() so they remain unused. The only platform
defining omap2_hsmmc_info also define both to -1, unused.
It turn out there are no boardfiles passing any valid GPIO
lines into the OMAP HSMMC driver at all. And since we are not
going to add any more OMAP2 boardfiles, we can delete this
card detect and write protect handling altogether.
This seems to also fix a bug: the card detect callback
mmc_gpio_get_cd() in the slot GPIO core needs to be called
by drivers utilizing slot GPIO. It appears the the boardfile
quirks were not doing this right, so this would only get
called for boardfiles, i.e. since no boardfile was using it,
never.
Just assign mmc_gpio_get_cd() unconditionally to omap_hsmmc_ops
.get_cd() so card detects from the device tree works.
AFAICT card detect with GPIO lines assigned from
mmc_of_parse() are not working at the moment, but that is
no regression since it probably never worked.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cover detection appears to be a feature protecting the SD
card on mobile phones with a slide-cover, such as some Nokia
phones. The idea seems to be to not allow access to the
SD card when the cover is open.
It is only usable with platform data from board files, but
no board file in the kernel is using it, yet it takes up
a sizeable chunk of code in the OMAP HSMMC driver.
Since we do not add new board files for the OMAPs any target
that need this should anyway reimplement it properly using
the device tree, so delete this legacy code.
The driver is marked as orphan in MAINTAINERS by the way.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
If the retrieveal is successful, we also request the IRQ.
As a result the private subdriver data can be removed
entirely.
Cc: Weijun Yang <york.yang@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform data for the PXAv3 driver allows passing a card
detect GPIO, but this code is not used in the kernel.
In order to not encourage the use of the old global GPIO
numberspace we need to remove this.
Card detect (and write protect) GPIO can easily be added into
the driver using machine descriptor tables instead, and the
descriptor-based (gpiod) variants of the slot GPIO APIs.
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.
renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
longer than device claims to support [len=126976] [max=65536]
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
and added comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.
Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.
The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.
This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.
This patch add this new mode support.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.
Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.
For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD host controller specification version 4.10, when
Host Version 4 is enabled, SDMA uses ADMA System Address register
(05Fh-058h) instead of using SDMA System Address register to
support both 32-bit and 64-bit addressing.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode. This patch introduced an interface to enable
v4 mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix inconsistent IS_ERR and PTR_ERR in tegra_sdhci_init_pinctrl_info,
the proper pointer to be passed as argument is 'pinctrl_state_1v8'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rerun the pad calibration procedure before sdhci_request() if
the 100 ms recalibration interval has been exceeded.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement HS400 specific delay line calibration procedure. This is a
Tegra specific procedure and has to be performed regardless whether
enhanced strobe or HS400 tuning is used.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse and program the HS400 DQS trim value from DT. Program a fallback
value in case the property is missing.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement tegra210_sdhci_writew() to disable card clock and issue a
reset when the tuning command is sent. This is done to prevent an
intermittent hang with around 10 % failure rate during tuning.
Add tegra186_sdhci_ops because this workaround is specific to Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new sdhci_ops struct for Tegra210 and Tegra186 which doesn't
set the custom tuning callback used on previous SoC generations.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program the outbound sampling trim value in tegra_sdhci_reset(). Unlike
the outbound tap value this does not depend on the signaling mode and
needs to be only programmed once.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default inbound timing adjustment tap value on reset and on
non-tunable modes.
The default tap value is not programmed on tunable modes because the
tuning sequence is used instead to determine the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable the card clock during configuration of the tap
value in tegra_sdhci_set_tap() and issue sdhci_reset() after value
change. This is a workaround to avoid propagation of a potential
glitch caused by setting the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set NVQUIRK_HAS_PADCALIB on Tegra210 and Tegra186 to enable automatic
pad drive strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Run the automatic pad calibration after voltage switching if
tegra_host->pad_calib_required is set.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pad drive strength calibration offsets from the device tree.
Program the calibration offsets in accordance with the current signaling
mode.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable the card clock during automatic pad drive strength calibration
and re-enable it afterwards.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic pad drive strength calibration is performed on a separate pad
identical to the ones used for driving the actual bus. Power on the
calibration pad during the calibration procedure and power it off
afterwards to save power.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Configure the voltage reference used by the automatic pad drive strength
calibration procedure. The value is a magic number from the TRM.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.
The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variable is unused now after some refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1)
clock <<= 1;
... is too tricky, hence I replaced with
roundup_pow_of_two(divisor) >> 2
'(clk >> 22) & 0x1' is the bit test for the 1/1 divisor, but
it is not clear. 'divisor <= 1' is easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock(). Merge them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using DMA, if the DMA addr spans 128MB boundary, we have to split
the DMA transfer into two so that each one doesn't exceed the boundary.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.
Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.
Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In tuning mode of operation, when TBCTL[TB_EN] is set, eSDHC may report
one of the following errors :
1)Tuning error while running tuning operation where SYSCTL2[SAMPCLKSEL]
will not get set even when SYSCTL2[EXTN] is reset. OR
2)Data transaction error (e.g. IRQSTAT[DCE], IRQSTAT[DEBE]) during data
transaction errors.
This issue occurs when the data window sampled within eSDHC is in full
cycle. So, in that case, eSDHC is not able to find out the start and
end points of the data window and sets the sampling pointer at default
location (which is middle of the internal SD clock). If this sampling
point coincides with the data eye boundary, then it can result in the
above mentioned errors. Impact: Tuning mode of operation for SDR50,
SDR104 or HS200 speed modes may not work properly
Workaround: In case eSDHC reports tuning error or data errors in tuning
mode of operation, by add the erratum A008171 support to fix the issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add tuning error codes to
judge tuning state
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is another TMIO MMC variant found in Socionext UniPhier SoCs.
As commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.
However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP. The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.
Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c
Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c. The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.
Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.
Renesas Socionext
SDHI UniPhier
DM_CM_DTRAN_MODE 0x820 0x410
DM_CM_DTRAN_CTRL 0x828 0x414
DM_CM_RST 0x830 0x418
DM_CM_INFO1 0x840 0x420
DM_CM_INFO1_MASK 0x848 0x424
DM_CM_INFO2 0x850 0x428
DM_CM_INFO2_MASK 0x858 0x42c
DM_DTRAN_ADDR 0x880 0x440
DM_DTRAN_ADDREX --- 0x444
This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs. Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.
It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.
The original IP defines the divisor range 1/2 ... 1/512.
bit 7 is set: 1/512
bit 6 is set: 1/256
...
bit 0 is set: 1/4
all bits clear: 1/2
It is platform-dependent how to achieve the 1/1 clock.
I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c
I guess bit[7:0]=0xff is Renesas-specific extension.
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.
To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_clk_stop(host) is equivalent to tmio_mmc_set_clock(host, 0).
This replacement is needed for the next commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on the V3H Starter Kit board and since the
R8A77970 SoC has a single SDHI core, it can't be a subject to the known RX
DMA errata.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Remove the stray underscore in the DM_CM_DTRAN_MODE.BUS_WIDTH register
field name and fix the typo in the comment of the #define
DTRAN_MODE_CH_NUM_CH1.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on MACH_JZ4740 | MACH_JZ4780 prevent us from creating a generic
kernel that works on more than one MIPS board. Instead, we just depend on
MIPS being set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable access to the RPMB on the on-board eMMC of the
Poplar board.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert DT properties to generic device properties
so that drivers can get properties from DT or ACPI.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.
Fixes: 1d71926bbd ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
after unbinding mmc I get things like this:
[ 185.294067] mmc1: card 0001 removed
[ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13
The wakeirq stays in /proc-interrupts
rebinding shows this:
[ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling
That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.
So let us cleanup at removal.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234b ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the SDHI DMA interrupts enabled while the Linux driver didn't use those.
Masking those interrupts in renesas_sdhi_internal_dmac_request_dma() gets
rid of both issues...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DM_CM_RST register actually has bits 0-31 defaulting to 1s and bits
32-63 defaulting to 0s -- fix off-by-one in #define RST_RESERVED_BITS.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.
Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(dest, host->virt_base, data->sg->length) where
dest is the virtual address of the SG. Same for sg_copy_from_buffer
but in the opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 53d7e098ba ("mmc: android-goldfish: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(buf + offset, &value, remaining) where buf is
the virtual address of the SG. Same for sg_copy_to_buffer but in the
opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 5b4277814e ("mmc: atmel-mci: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.
When fail to set 8bit mode, need return error directly for HS400es.
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When tuning each tap is issued CMD19 twice and the result of both runs
recorded in host->taps. If the result is different between the two runs
the wrong sampling clock position was selected. Fix this by merging the
two runs and only keep the result for each tap if it was good in both
sets.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the return value of mmc_send_tuning() is error other than -EILSEQ,
the tuning fails and process goes out of for_loop. The correct
processing is to judge their TAP as not good (NG) and continue.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent Linux versions refuse to print actual virtual kernel addresses,
to not give a hint about the location of the kernel in a randomized virtual
address space. This affects the output of the sunxi MMC controller
driver, which now produces the rather uninformative line:
[ 1.482660] sunxi-mmc 1c0f000.mmc: base:0x(____ptrval____) irq:8
Since the virtual base address is not really interesting in the first
place, let's just drop this value. The same applies to Linux' notion of
the interrupt number, which is independent from the GIC SPI number.
We have the physical address as part of the DT node name, which is way
more useful for debugging purposes.
To keep a success message in the driver, we make this purpose explicit
with the word "initialized", plus print some information that is not too
obvious and that we learned while probing the device:
the maximum request size and whether it uses the new timing mode.
So the output turns into:
[ 1.750626] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.786699] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Allwinner boards feature an on-board eMMC with fixed 3.3V voltage
(e.g. Banana Pi M2+), and in this case both the eMMC and the SoC are
capable of doing 3.3V DDR transmission.
Add capability of 3.3V DDR when DDR is available (extra clock or new
timing).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tegra SDHCI controllers require the SDHCI clock divider to be configured
to divide the clock by two in DDR50/52 modes. Incorrectly configured
clock divider results in corrupted data.
Prevent the possibility of incorrectly calculating the divider value due
to clock rate rounding or low parent clock frequency by not assigning
host->max_clk to clk_get_rate() on tegra_sdhci_set_clock().
See the comments for further details.
Fixes: a8e326a ("mmc: tegra: implement module external clock change")
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MSI interrupt support if the SD host device can support MSI interrupt.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci tuning function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
O2 SD Host HS200 mode clock frequency current is 208MHz, should be changed
to 200MHz to meet specification.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use eMMC as boot device, the eMMC signaling voltage is tied to 1.8v
fixed output voltage, bios can set o2 sd host controller PCI configuration
register 0x308 bit4 to 1 to let driver skip 3.3v signaling voltage and
direct use 1.8v singling voltage in eMMC initialize process.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement and use tegra_sdhci_get_max_clock() which returns the true
maximum host clock rate. The issue with tegra_sdhci_get_max_clock() is
that it returns the current clock rate of the host instead of the
maximum one, which can lead to unnecessarily small clock rates.
This differs from the previous implementation of
tegra_sdhci_get_max_clock() in that it doesn't divide the result by two.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the uSDHC case (e.g. i.MX 6) clocks only get disabled if frequency
is set to 0. However, it could be that the stack asks for a frequency
change while clocks are on. In that case the function clears the
divider registers (by clearing ESDHC_CLOCK_MASK) while the clock is
enabled! This causes a short period of time where the clock is
undivided (on a i.MX 6DL a clock of 196MHz has been measured).
For older IP variants the driver disables clock by clearing some bits
in ESDHC_SYSTEM_CONTROL.
Make sure to disable card clock before changing frequency for uSDHC
IP variants too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that SD3.0 advertisement needs to be set for higher eMMC
speed modes (namely DDR52) as well. The TRM states that the SD3.0
advertisement bit should be set for all controller instances, even
for those not supporting UHS-I mode...
When specifying vqmmc-supply as a fixed 1.8V regulator on a Tegra
SD/MMC instance which is connected to a eMMC device, the stack
enables SD3.0. However, enabling it has consequences: If SDHCI 3.0
support is advertised the stack enables Auto-CMD23. Unfortunately
Auto-CMD23 seems not to work well with Tegra 3 currently. It leads
to regular warnings:
mmc2: Got command interrupt 0x00010000 even though no command operation was in progress.
It is not entirely clear why those errors happens. It seems that
a Linux 3.1 based downstream kernel which has Auto-CMD23 support
does not show those warnings.
Use quirk SDHCI_QUIRK2_ACMD23_BROKEN to prevent Auto-CMD23 being
used for now. With this the eMMC works stable on high-speed mode
while still announcing SD3.0.
This allows to use mmc-ddr-1_8v to enables DDR52 mode. In DDR52
mode read speed improves from about 42MiB/s to 72MiB/s on an
Apalis T30.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sure the clock is doubled when using eMMC DDR52 mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stack assumes that SDHC controller which support SD3.0 (SDR104) do
support HS200. This is not the case for Tegra 3, which does support SD
3.0
but only supports eMMC spec 4.41.
Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not
support HS200.
Note that commit 156e14b126 ("mmc: sdhci: fix caps2 for HS200") added
the tie between SD3.0 (SDR104) and HS200. I don't think that this is
necessarly true. It is fully legitimate to support SD3.0 and not support
HS200. The quirk naming suggests something is broken in the controller,
but this is not the case: The controller simply does not support HS200.
Fixes: 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys has DWC MSHC controller on HPAS-DX platform connected using PCIe
interface with SD card slot and eMMC device slots. This patch is to
enable SD cards connected on this platform. As Clock generation logic
is implemented using MMCM module of HAPS-DX platform, we have separate
functions to control the MMCM to generate required clocks with respect
to speed mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a driver for SDHCI OF Synopsys DesignWare Cores Mobile Storage
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
mmc1: Switching to 3.3V signalling voltage failed
Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A recent commit introduced a call to mmc_of_parse() and removed the
explicit assignment of GPIOs in the pdata structure. This will leave
them set to 0, which is a valid GPIO per se, so the code that looks
at these members will try to allocate them and fail.
To fix this properly, make the following changes:
a) Refrain from allocating and assiging a pdata struct from
pxamci_of_init(). It's a hack to do it this way anyway.
Instead, move the only remaining member of interest in
'struct pxamci_host' and assign the value from either
the passed in pdata pointer or with the value read from DT.
b) Let the only user of 'detect_delay_ms' look at the member of
'struct pxamci_host', not the pdata.
c) Make more code in pxamci_probe() dependent on the presence of
actual pdata.
This will also ease the removal of pdata one day.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Strip some code by letting the mmc core handle the regulators. The old
.gpio_power pdata handling is kept around for now.
This also set the voltage on the regulator and handles -EPROBE_DEFER
correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Devicetree-enabled boards should use proper regulators to control the
power of cards, not GPIOs, so let's remove this property. The regulator
properties are supported by the MMC core and are described in the
generic MMC document:
Documentation/devicetree/bindings/mmc/mmc.txt
Note that devicetree support for PXA platforms hasn't fully landed yet,
so this binding does not have any users at this point.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
