There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If CONFIG_PHYS_ADDR_T_64BIT is set, compilation of sbc8560 fails with
the following error:
arch/powerpc/platforms/85xx/sbc8560.c: In function ‘sbc8560_bdrstcr_init’:
arch/powerpc/platforms/85xx/sbc8560.c:286: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’
Fix that by using %pR format instead of just printing the start of
resource.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver. The other three are special modes
that don't make sense for a framebuffer driver. Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Apple Quad G5 has some oddity in it's device-tree which causes the new
generic matching code to fail to relate nodes for PCI-E devices below U4
with their respective struct pci_dev. This breaks graphics on those
machines among others.
This fixes it using a quirk which copies the node pointer from the host
bridge for the root complex, which makes the generic code work for the
children afterward.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The firmware on old 970 blades supports some kind of takeover called
"TNK takeover" which will crash if we try to probe for OPAL takeover,
so don't do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current L1 cache read event code 0x80082 only counts for thread 0. The
event code 0x280030 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache read.
The current L1 cache write event code 0x80086 only counts for thread 0. The
event code 0x180032 should be used to count events on thread 0 and 1. The
patch fixes the event code for the L1 cache write.
FYI, the documentation lists three event codes for the L1 cache read event
and three event codes for the L1 cache write event. The event description
for the event codes is as follows:
L1 cache read requests 0x80082 LSU 0 only
L1 cache read requests 0x8008A LSU 1 only
L1 cache read requests 0x80030 LSU 1 or LSU 0, counter 2 only.
L1 cache store requests 0x80086 LSU 0 only
L1 cache store requests 0x8008E LSU 1 only
L1 cache store requests 0x80032 LSU 0 or LSU 1, counter 1 only.
There can only be one request from either LSU 0 or 1 active at a time.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
gcc (rightfully) complains that we are accessing beyond the
end of the fpr array (we do, to access the fpscr).
The only sane thing to do (whether anything in that code can be
called remotely sane is debatable) is to special case fpscr and
handle it as a separate statement.
I initially tried to do it it by making the array access conditional
to index < PT_FPSCR and using a 3rd else leg but for some reason gcc
was unable to understand it and still spewed the warning.
So I ended up with something a tad more intricated but it seems to
build on 32-bit and on 64-bit with and without VSX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on patch by David Gibson <dwg@au1.ibm.com>
xmon has a longstanding bug on systems which are SMP-capable but lack
the MSR[RI] bit. In these cases, xmon invoked by IPI on secondary
CPUs will not properly keep quiet, but will print stuff, thereby
garbling the primary xmon's output. This patch fixes it, by ignoring
the RI bit if the processor does not support it.
There's already a version of this for 4xx upstream, which we'll need
to extend to other RI-lacking CPUs at some point. For now this adds
Book3e processors to the mix.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We don't want to configure PCI Express Max Payload Size or
Max Read Request Size on systems that set that flag. The
firmware will have done it for us, and under hypervisors such
as pHyp we don't even see the parent switches and bridges and
thus can make no assumption on what values are safe to use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With a KVM guest operating in SMT4 mode (i.e. 4 hardware threads per
core), whenever a CPU goes idle, we have to pull all the other
hardware threads in the core out of the guest, because the H_CEDE
hcall is handled in the kernel. This is inefficient.
This adds code to book3s_hv_rmhandlers.S to handle the H_CEDE hcall
in real mode. When a guest vcpu does an H_CEDE hcall, we now only
exit to the kernel if all the other vcpus in the same core are also
idle. Otherwise we mark this vcpu as napping, save state that could
be lost in nap mode (mainly GPRs and FPRs), and execute the nap
instruction. When the thread wakes up, because of a decrementer or
external interrupt, we come back in at kvm_start_guest (from the
system reset interrupt vector), find the `napping' flag set in the
paca, and go to the resume path.
This has some other ramifications. First, when starting a core, we
now start all the threads, both those that are immediately runnable and
those that are idle. This is so that we don't have to pull all the
threads out of the guest when an idle thread gets a decrementer interrupt
and wants to start running. In fact the idle threads will all start
with the H_CEDE hcall returning; being idle they will just do another
H_CEDE immediately and go to nap mode.
This required some changes to kvmppc_run_core() and kvmppc_run_vcpu().
These functions have been restructured to make them simpler and clearer.
We introduce a level of indirection in the wait queue that gets woken
when external and decrementer interrupts get generated for a vcpu, so
that we can have the 4 vcpus in a vcore using the same wait queue.
We need this because the 4 vcpus are being handled by one thread.
Secondly, when we need to exit from the guest to the kernel, we now
have to generate an IPI for any napping threads, because an HDEC
interrupt doesn't wake up a napping thread.
Thirdly, we now need to be able to handle virtual external interrupts
and decrementer interrupts becoming pending while a thread is napping,
and deliver those interrupts to the guest when the thread wakes.
This is done in kvmppc_cede_reentry, just before fast_guest_return.
Finally, since we are not using the generic kvm_vcpu_block for book3s_hv,
and hence not calling kvm_arch_vcpu_runnable, we can remove the #ifdef
from kvm_arch_vcpu_runnable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This simplifies the way that the book3s_pr makes the transition to
real mode when entering the guest. We now call kvmppc_entry_trampoline
(renamed from kvmppc_rmcall) in the base kernel using a normal function
call instead of doing an indirect call through a pointer in the vcpu.
If kvm is a module, the module loader takes care of generating a
trampoline as it does for other calls to functions outside the module.
kvmppc_entry_trampoline then disables interrupts and jumps to
kvmppc_handler_trampoline_enter in real mode using an rfi[d].
That then uses the link register as the address to return to
(potentially in module space) when the guest exits.
This also simplifies the way that we call the Linux interrupt handler
when we exit the guest due to an external, decrementer or performance
monitor interrupt. Instead of turning on the MMU, then deciding that
we need to call the Linux handler and turning the MMU back off again,
we now go straight to the handler at the point where we would turn the
MMU on. The handler will then return to the virtual-mode code
(potentially in the module).
Along the way, this moves the setting and clearing of the HID5 DCBZ32
bit into real-mode interrupts-off code, and also makes sure that
we clear the MSR[RI] bit before loading values into SRR0/1.
The net result is that we no longer need any code addresses to be
stored in vcpu->arch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes arch/powerpc/kvm/book3s_rmhandlers.S and
arch/powerpc/kvm/book3s_hv_rmhandlers.S be assembled as
separate compilation units rather than having them #included in
arch/powerpc/kernel/exceptions-64s.S. We no longer have any
conditional branches between the exception prologs in
exceptions-64s.S and the KVM handlers, so there is no need to
keep their contents close together in the vmlinux image.
In their current location, they are using up part of the limited
space between the first-level interrupt handlers and the firmware
NMI data area at offset 0x7000, and with some kernel configurations
this area will overflow (e.g. allyesconfig), leading to an
"attempt to .org backwards" error when compiling exceptions-64s.S.
Moving them out requires that we add some #includes that the
book3s_{,hv_}rmhandlers.S code was previously getting implicitly
via exceptions-64s.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are multiple features in PowerPC KVM that can now be enabled
depending on the user's wishes. Some of the combinations don't make
sense or don't work though.
So this patch adds a way to check if the executing environment would
actually be able to run the guest properly. It also adds sanity
checks if PVR is set (should always be true given the current code
flow), if PAPR is only used with book3s_64 where it works and that
HV KVM is only used in PAPR mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that Book3S PV mode can also run PAPR guests, we can add a PAPR cap and
enable it for all Book3S targets. Enabling that CAP switches KVM into PAPR
mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR defines hypercalls as SC1 instructions. Using these, the guest modifies
page tables and does other privileged operations that it wouldn't be allowed
to do in supervisor mode.
This patch adds support for PR KVM to trap these instructions and route them
through the same PAPR hypercall interface that we already use for HV style
KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Recent Linux versions use the CFAR and PURR SPRs, but don't really care about
their contents (yet). So for now, we can simply return 0 when the guest wants
to read them.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a PAPR guest, we need to handle a few hypercalls in kernel space,
most prominently the page table invalidation (to sync the shadows).
So this patch adds handling for a few PAPR hypercalls to PR mode KVM. I tried
to share the code with HV mode, but it ended up being a lot easier this way
around, as the two differ too much in those details.
Signed-off-by: Alexander Graf <agraf@suse.de>
---
v1 -> v2:
- whitespace fix
Until now, we always set HIOR based on the PVR, but this is just wrong.
Instead, we should be setting HIOR explicitly, so user space can decide
what the initial HIOR value is - just like on real hardware.
We keep the old PVR based way around for backwards compatibility, but
once user space uses the SREGS based method, we drop the PVR logic.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have a few traps where we cache the instruction that cause the trap
for analysis later on. Since we now need to be able to distinguish
between SC 0 and SC 1 system calls and the only way to find out which
is which is by looking at the instruction, we also read out the instruction
causing the system call.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a PAPR guest, the guest is not allowed to set SDR1 - instead
the HTAB information is held in internal hypervisor structures. But all of
our current code relies on SDR1 and walking the HTAB like on real hardware.
So in order to not be too intrusive, we simply set SDR1 to the HTAB we hold
in host memory. That way we can keep the HTAB in user space, but use it from
kernel space to map the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have 3 privilege levels: problem state, supervisor state and hypervisor
state. Each of them can access different SPRs, so we need to check on every
SPR if it's accessible in the respective mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a PAPR guest, some things change. The privilege level drops
from hypervisor to supervisor, SDR1 gets treated differently and we interpret
hypercalls. For bisectability sake, add the flag now, but only enable it when
all the support code is there.
Signed-off-by: Alexander Graf <agraf@suse.de>
We need the compute_tlbie_rb in _pr and _hv implementations for papr
soon, so let's move it over to a common header file that both
implementations can leverage.
Signed-off-by: Alexander Graf <agraf@suse.de>
Some devices have a dma-window that starts at the address 0. This allows
DMA addresses to be mapped to this address and returned to drivers as a
valid DMA address. Some drivers may not behave well in this case, since
the address 0 is considered an error or not allocated.
The solution to avoid this kind of error from happening is reserve the
page addressed as 0 so it cannot be allocated for a DMA mapping.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 41151e77a4 ("powerpc: Hugetlb for BookE") added some
#ifdef CONFIG_MM_SLICES conditionals to hugetlb_get_unmapped_area()
and vma_mmu_pagesize(). Unfortunately this is not the correct config
symbol; it should be CONFIG_PPC_MM_SLICES. The result is that
attempting to use hugetlbfs on 64-bit Power server processors results
in an infinite stack recursion between get_unmapped_area() and
hugetlb_get_unmapped_area().
This fixes it by changing the #ifdef to use CONFIG_PPC_MM_SLICES
in those functions and also in book3e_hugetlb_preload().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Activate all MPC512x related boards. Also enable GPIO-driver, SPI driver
and at25 to test SPI. Enable DEVTMPFS. Bump to 3.1-rc6.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Audio support for the MPC5200 exists, so enable it by default.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
timer0 and timer1 pins are used as simple GPIO on this board.
Add gpio-controller and #gpio-cells properties to timer nodes
so that we can control gpio lines using available MPC52xx
GPT driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new nodes to describe more hardware the board is
equipped with:
- two can nodes for SJA1000 on localbus
- pci node to support Coral-PA graphics controller
- serial node for SC28L92 DUART on localbus
- spi node for MSP430 device
Also correct i2c eeprom node name.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
perf events, powerpc: Add POWER7 stalled-cycles-frontend/backend events
Extent the POWER7 PMU driver with definitions for generic front-end and back-end
stall events.
As explained in Ingo's original comment(8f62242246
), the exact definitions of the stall events are very much processor specific as
different things mean different in their respective instruction pipeline. These
two Power7 raw events are the closest approximation to the concept detailed in
Ingo's comment.
[PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = 0x100f8, /* GCT_NOSLOT_CYC */
It means cycles when the Global Completion Table has no slots from this thread
[PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = 0x4000a, /* CMPLU_STALL */
It means no groups completed and GCT not empty for this thread
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The firmware doesn't wait after lifting the PCI reset. However it does
timestamp it in the device tree. We use that to ensure we wait long
enough (3s is our current arbitrary setting) from that timestamp to
actually probing the bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This implements support for MSIs on p5ioc2 PHBs. We only support
MSIs on the PCIe PHBs, not the PCI-X ones as the later hasn't been
properly verified in HW.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for PCI-X and PCIe on the p5ioc2 IO hub using
OPAL. This includes allocating & setting up TCE tables and config
space access routines.
This also supports fallbacks via RTAS when OPAL is absent, using
legacy TCE format pre-allocated via the device-tree (BML style)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL can handle various interrupt for us such as Machine Checks (it
performs all sorts of recovery tasks and passes back control to us with
informations about the error), Hardware Management Interrupts and Softpatch
interrupts.
This wires up the mechanisms and prints out specific informations returned
by HAL when a machine check occurs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We do the minimum which is to "pass" interrupts to HAL, which
makes the console smoother and will allow us to implement
interrupt based completion and console.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL handles HW access to the various ICS or equivalent chips
for us (with the exception of p5ioc2 based HEA which uses a
different backend) similarily to what RTAS does on pSeries.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implements OPAL RTC and NVRAM support and wire all that up to
the powernv platform.
We use RTAS for RTC as a fallback if available. Using RTAS for nvram
is not supported yet, pending some rework/cleanup and generalization
of the pSeries & CHRP code. We also use RTAS fallbacks for power off
and reboot
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This calls the respective HAL functions, and spin on hal_poll_event()
to ensure the HAL has a chance to communicate with the FSP to trigger
the reboot or shutdown operation
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL v2 is instantiated in a way similar to RTAS using Open Firmware
client interface calls, and the resulting address and entry point are
put in the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add definition of OPAL interfaces along with the wrappers to call
into OPAL runtime and the early device-tree parsing hook to locate
the OPAL runtime firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We stash it in boot_command_line which isn't in BSS and so won't
be overwritten. We then use that as a default cmd_line before
we walk the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On machines supporting the OPAL firmware version 1, the system
is initially booted under pHyp. We then use a special hypercall
to verify if OPAL is available and if it is, we then trigger
a "takeover" which disables pHyp and loads the OPAL runtime
firmware, giving control to the kernel in hypervisor mode.
This patch add the necessary code to detect that the OPAL takeover
capability is present when running under PowerVM (aka pHyp) and
perform said takeover to get hypervisor control of the processor.
To perform the takeover, we must first use RTAS (within Open
Firmware runtime environment) to start all processors & threads,
in order to give control to OPAL on all of them. We then call
the takeover hypercall on everybody, OPAL will re-enter the kernel
main entry point passing it a flat device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.
These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.
The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With OPAL, r8 and r9 will be used to pass the OPAL base and entry
for debugging purposes (those informations are also in the
device-tree). We don't want to clobber those registers that
early.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This new function is used to properly setup the PCI Express Max Payload Size
(and in some circumstances Max Read Request Size).
Some systems will not operate properly if these aren't set correctly and
the firmware doesn't always do it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds more generic support for doing CPU hotplug with a simple
idle loop and no actual reset of the processors. The generic
smp_generic_kick_cpu() does the hotplug bringup trick if the PACA
shows that the CPU has already been started at boot and we provide
an accessor for the CPU state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was preventing the global early debug selection whenever KVM was enabled
instead of only preventing the 440 specific one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The icswx code introduced an A-B B-A deadlock:
CPU0 CPU1
---- ----
lock(&anon_vma->mutex);
lock(&mm->mmap_sem);
lock(&anon_vma->mutex);
lock(&mm->mmap_sem);
Instead of using the mmap_sem to keep mm_users constant, take the
page table spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we echo an address the hypervisor doesn't like to
/sys/devices/system/memory/probe we oops the box:
# echo 0x10000000000 > /sys/devices/system/memory/probe
kernel BUG at arch/powerpc/mm/hash_utils_64.c:541!
The backtrace is:
create_section_mapping
arch_add_memory
add_memory
memory_probe_store
sysdev_class_store
sysfs_write_file
vfs_write
SyS_write
In create_section_mapping we BUG if htab_bolt_mapping returned
an error. A better approach is to return an error which will
propagate back to userspace.
Rerunning the test with this patch applied:
# echo 0x10000000000 > /sys/devices/system/memory/probe
-bash: echo: write error: Invalid argument
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While converting code to use for_each_node_by_type I noticed a
number of coding style issues.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use for_each_node_by_type instead of open coding it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During memory hotplug testing, I got the following warning:
ERROR: Bad of_node_put() on /memory@0
of_node_release
kref_put
of_node_put
of_find_node_by_type
hot_add_node_scn_to_nid
hot_add_scn_to_nid
memory_add_physaddr_to_nid
...
of_find_node_by_type() loop does the of_node_put for us so we only
need the handle the case where we terminate the loop early.
As suggested by Stephen Rothwell we can do the of_node_put
unconditionally outside of the loop since of_node_put handles a
NULL argument fine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two identical definitions of RECLAIM_DISTANCE, looks like
the patch got applied twice. Remove one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On big POWER7 boxes we see large amounts of CPU time in system
processes like workqueue and watchdog kernel threads.
We currently rebalance the entire machine each time a task goes
idle and this is very expensive on large machines. Disable newidle
balancing at the node level and rely on the scheduler tick to
rebalance across nodes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The largest POWER7 boxes have 32 nodes. SD_NODES_PER_DOMAIN groups
nodes into chunks of 16 and adds a global balancing domain
(SD_ALLNODES) above it.
If we bump SD_NODES_PER_DOMAIN to 32, then we avoid this extra
level of balancing on our largest boxes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When chasing a performance issue on ppc64, I noticed tasks
communicating via a pipe would often end up on different nodes.
It turns out SD_WAKE_AFFINE is not set in our node defition. Commit
9fcd18c9e6 (sched: re-tune balancing) enabled SD_WAKE_AFFINE
in the node definition for x86 and we need a similar change for
ppc64.
I used lmbench lat_ctx and perf bench pipe to verify this fix. Each
benchmark was run 10 times and the average taken.
lmbench lat_ctx:
before: 66565 ops/sec
after: 204700 ops/sec
3.1x faster
perf bench pipe:
before: 5.6570 usecs
after: 1.3470 usecs
4.2x faster
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a new udbg driver for the PS3 gelic Ehthernet device.
This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit 188917e183, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.
Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org> [3.x]
This should fix the following warning:
LD arch/powerpc/sysdev/xics/built-in.o
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1310): Section mismatch in
reference from the function .icp_native_init() to the function
.init.text:.icp_native_init_one_node()
The function .icp_native_init() references
the function __init .icp_native_init_one_node().
This is often because .icp_native_init lacks a __init
annotation or the annotation of .icp_native_init_one_node is wrong.
icp_native_init() is only referenced in `arch/powerpc/sysdev/xics/xics-common.c'
by xics_init() which is itself marked with __init.
= not built-tested =
Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During hotplug CPU add we get the following error:
Unexpected Error (0) returned from configure-connector
ibm,configure-connector returns 0 for configuration complete, so
catch this and avoid the error.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
In SMP mode, the kernel would produce call trace when resumed
from hibernation. The reason is when the function destroy_context
is called to drop the resuming mm context, the mm->context.active
is 1 which is wrong and should be zero.
We pass the current->active_mm as previous mm context to function
switch_mmu_context to decrease the context.active by 1.
In UP mode, there is no effect.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The various port_init_hw methods of ppc4xx_pciex_hwops should have been
marked __init and when I added ppc4xx_pciex_port_reset_sdr(), which is
__init. This added many section mismatch warnings like:
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x5c68): Section mismatch in reference from the function ppc440spe_pciex_init_port_hw() to the function .init.text:ppc4xx_pciex_port_reset_sdr()
The function ppc440spe_pciex_init_port_hw() references
the function __init ppc4xx_pciex_port_reset_sdr().
This is often because ppc440spe_pciex_init_port_hw lacks a __init
annotation or the annotation of ppc4xx_pciex_port_reset_sdr is wrong.
Trivial patch to silence those warnings.
Reported-By: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Yours Tony
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by Michael Ellerman <michael@ellerman.id.au>
Patch was simply forward ported upstream.
Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by Benjamin Herrenschmidt <benh@kernel.crashing.org>
Modernized and slightly modified to not record erros into the nvram
log since we do not have that device driver just yet.
Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some config selections were applied to the platform (reference board)
when they actuall apply to the chip.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At this point, window has not been stored anywhere, so it has to be freed
before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
u64 is used rather than phys_addr_t to keep things simple, as
this is called from assembly code.
Update callers to pass a 64-bit address in r3/r4. Other unused
register assignments that were once parameters to machine_init
are dropped.
For FSL BookE, look up the physical address of the device tree from the
effective address passed in r3 by the loader. This is required for
situations where memory does not start at zero (due to AMP or IOMMU-less
virtualization), and thus the IMA doesn't start at zero, and thus the
device tree effective address does not equal the physical address.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Capture more than twice as much text from the printk buffer, and
compress it to fit it in the lnx,oops-log NVRAM partition. You
can view the compressed text using the new (as of July 20) --unzip
option of the nvram command in the powerpc-utils package.
[BenH: Added select of ZLIB_DEFLATE]
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is one place in the MPIC driver that assumes that the cores are numbered
from 0 to n-1. However, this is not true if the CPUs are not numbered
sequentially. This can happen on a eight-core SOC where cores two and three
are removed in the device tree. So instead of blindly looping, we iterate
over the discovered CPUs and use the SMP ID as the index.
This means that we no longer ask the MPIC how many CPUs there are, so
we also delete mpic->num_cpus.
We also catch if the number of CPUs in the SOC exceeds the number that the
MPIC supports. This should never happen, of course, but it's good to be
sure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable hugepages on Freescale BookE processors. This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints. Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.
The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).
This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This iotype is only used by the legacy_serial code in powerpc, so the
code should live there, rather than be compiled in for every 8250
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-serial@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new get_required_mask hook name is longer than many of but not all
of the prior ops. Tidy the struct initializers to align the equal signs
using the local whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.
If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.
This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask. I doubt anything is checking or setting the dma mask on
that bus.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
uic->lock is protecting the interrupt controller hardware. This lock
can not be preempted on -rt.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Reported-by: Darcy L. Watkins <dwatkins@tranzeo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently. The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn. However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.
Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size. Coverting from the end address
to the required bit mask is based on the generic implementation.
The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/p1023rds: Fix the error of bank-width of nor flash
powerpc/85xx: enable caam crypto driver by default
powerpc/85xx: enable the audio drivers in the defconfigs
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These were missed in commit f5b9409973 "All Arch: remove linkage
for sys_nfsservctl system call" due to them having no sys_ prefix
(presumably).
Cc: NeilBrown <neilb@suse.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes. This driver provides Linux kernel support for byte
channels via three distinct interfaces:
1) An early-console (udbg) driver. This provides early console output
through a byte channel. The byte channel handle must be specified in a
Kconfig option.
2) A normal console driver. Output is sent to the byte channel designated
for stdout in the device tree. The console driver is for handling kernel
printk calls.
3) A tty driver, which is used to handle user-space input and output. The
byte channel used for the console is designated as the default tty.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*
The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors). In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.
We do not explicitly select the Kconfig dependencies, as this would force
EMAC on. Doing it in the defconfig allows more flexibility.
Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the p1010 processor to select the flexcan network driver.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a register to the config space for the 460sx. Changes the vc0
detect to a pll detect. maps configuration space to test the link
status. changes the setup to enable gen2 devices to operate at gen2
speeds. fixes mapping that was not correct for the 460sx. added
bit definitions for the OMRxMSKL registers. Removed reserved bit
that was set incorrectly in the OMR2MSKL register.
tested on the 460sx eiger and custom board
Signed-off-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
This patch adds kexec support for PPC440 based chipsets. This work is based
on the KEXEC patches for FSL BookE.
The FSL BookE patch and the code flow could be found at the link below:
http://patchwork.ozlabs.org/patch/49359/
Steps:
1) Invalidate all the TLB entries except the one this code is run from
2) Create a tmp mapping for our code in the other address space and jump to it
3) Invalidate the entry we used
4) Create a 1:1 mapping for 0-2GiB in blocks of 256M
5) Jump to the new 1:1 mapping and invalidate the tmp mapping
I have tested this patches on Ebony, Sequoia boards and Virtex on QEMU.
You need kexec-tools commit e8b7939b1e or newer for ppc440x support,
available at:
git://git.kernel.org/pub/scm/utils/kernel/kexec/kexec-tools.git
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit fea80311a9
"iomap: make IOPORT/PCI mapping functions conditional"
Broke powerpc build without CONFIG_PCI as we would still define
pci_iomap(), which overlaps with the new empty inline in the headers.
Make our implementation conditional on CONFIG_PCI
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 112d1fe9f7
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.
Move them back out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The VPA, SLB shadow and DTL degistration functions do not need an
address, so simplify things and remove it.
Also cleanup pseries_kexec_cpu_down a bit by storing the cpu IDs
in local variables.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make the VPA, SLB shadow and DTL registration and deregistration
functions print consistent messages on error. I needed the firmware
error code while chasing a kexec bug but we weren't printing it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent versions of firmware will fail to unmap the virtual processor
area if we have a dispatch trace log registered. This causes kexec
to fail.
If a trace log is registered this patch unregisters it before the
SLB shadow and virtual processor areas, fixing the problem.
The address argument is ignored by firmware on unregister so we
may as well remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVM_GUEST adds a 1 MB array to the kernel (kvm_tmp) which grew
my kernel enough to cause it to fail to boot.
Dynamically allocating or reducing the size of this array is a
good idea, but in the meantime I think it makes sense to make
KVM_GUEST default to n in order to minimise surprises.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a box with gcc 4.3.2, I see errors like:
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1254: Error: Unrecognized opcode: stxvd2x
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1316: Error: Unrecognized opcode: lxvd2x
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ibm,io-events code is a bit verbose with its error messages.
Reverse the reporting so we only print when we successfully enable
I/O event interrupts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing boot failures on some very large boxes even with
commit b5416ca9f8 (powerpc: Move kdump default base address to
64MB on 64bit).
This patch halves the RMO so both kernels get about the same
amount of RMO memory. On large machines this region will be
at least 256MB, so each kernel will get 128MB.
We cap it at 256MB (small SLB size) since some early allocations need
to be in the bolted SLB region. We could relax this on machines with
1TB SLBs in a future patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Panic observed on an older kernel when collecting call chains for
the context-switch software event:
[<b0180e00>]rb_erase+0x1b4/0x3e8
[<b00430f4>]__dequeue_entity+0x50/0xe8
[<b0043304>]set_next_entity+0x178/0x1bc
[<b0043440>]pick_next_task_fair+0xb0/0x118
[<b02ada80>]schedule+0x500/0x614
[<b02afaa8>]rwsem_down_failed_common+0xf0/0x264
[<b02afca0>]rwsem_down_read_failed+0x34/0x54
[<b02aed4c>]down_read+0x3c/0x54
[<b0023b58>]do_page_fault+0x114/0x5e8
[<b001e350>]handle_page_fault+0xc/0x80
[<b0022dec>]perf_callchain+0x224/0x31c
[<b009ba70>]perf_prepare_sample+0x240/0x2fc
[<b009d760>]__perf_event_overflow+0x280/0x398
[<b009d914>]perf_swevent_overflow+0x9c/0x10c
[<b009db54>]perf_swevent_ctx_event+0x1d0/0x230
[<b009dc38>]do_perf_sw_event+0x84/0xe4
[<b009dde8>]perf_sw_event_context_switch+0x150/0x1b4
[<b009de90>]perf_event_task_sched_out+0x44/0x2d4
[<b02ad840>]schedule+0x2c0/0x614
[<b0047dc0>]__cond_resched+0x34/0x90
[<b02adcc8>]_cond_resched+0x4c/0x68
[<b00bccf8>]move_page_tables+0xb0/0x418
[<b00d7ee0>]setup_arg_pages+0x184/0x2a0
[<b0110914>]load_elf_binary+0x394/0x1208
[<b00d6e28>]search_binary_handler+0xe0/0x2c4
[<b00d834c>]do_execve+0x1bc/0x268
[<b0015394>]sys_execve+0x84/0xc8
[<b001df10>]ret_from_syscall+0x0/0x3c
A page fault occurred walking the callchain while creating a perf
sample for the context-switch event. To handle the page fault the
mmap_sem is needed, but it is currently held by setup_arg_pages.
(setup_arg_pages calls shift_arg_pages with the mmap_sem held.
shift_arg_pages then calls move_page_tables which has a cond_resched
at the top of its for loop - hitting that cond_resched is what caused
the context switch.)
This is an extension of Anton's proposed patch:
https://lkml.org/lkml/2011/7/24/151
adding case for 32-bit ppc.
Tested on the system that first generated the panic and then again
with latest kernel using a PPC VM. I am not able to test the 64-bit
path - I do not have H/W for it and 64-bit PPC VMs (qemu on Intel)
is horribly slow.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One definition of PV_POWER7 seems enough to me.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I hit an oops at boot on the first instruction of timer_cpu_notify:
NIP [c000000000722f88] .timer_cpu_notify+0x0/0x388
The code should look like:
c000000000722f78: eb e9 00 30 ld r31,48(r9)
c000000000722f7c: 2f bf 00 00 cmpdi cr7,r31,0
c000000000722f80: 40 9e ff 44 bne+ cr7,c000000000722ec4
c000000000722f84: 4b ff ff 74 b c000000000722ef8
c000000000722f88 <.timer_cpu_notify>:
c000000000722f88: 7c 08 02 a6 mflr r0
c000000000722f8c: 2f a4 00 07 cmpdi cr7,r4,7
c000000000722f90: fb c1 ff f0 std r30,-16(r1)
c000000000722f94: fb 61 ff d8 std r27,-40(r1)
But the oops output shows:
eb61ffd8 eb81ffe0 eba1ffe8 ebc1fff0 7c0803a6 ebe1fff8 4e800020
00000000 ebe90030 c0000000 00ad0a28 00000000 2fa40007 fbc1fff0 fb61ffd8
So we scribbled over our instructions with c000000000ad0a28, which
is an address inside the jump_table ELF section.
It turns out the jump_table section is only aligned to 8 bytes but
we are aligning our entries within the section to 16 bytes. This
means our entries are offset from the table:
c000000000acd4a8 <__start___jump_table>:
...
c000000000ad0a10: c0 00 00 00 lfs f0,0(0)
c000000000ad0a14: 00 70 cd 5c .long 0x70cd5c
c000000000ad0a18: c0 00 00 00 lfs f0,0(0)
c000000000ad0a1c: 00 70 cd 90 .long 0x70cd90
c000000000ad0a20: c0 00 00 00 lfs f0,0(0)
c000000000ad0a24: 00 ac a4 20 .long 0xaca420
And the jump table sort code gets very confused and writes into the
wrong spot. Remove the alignment, and also remove the padding since
we it saves some space and we shouldn't need it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a box that fails in OF during boot with:
DEFAULT CATCH!, exception-handler=fff00400
at %SRR0: 49424d2c4c6f6768 %SRR1: 800000004000b002
ie "IBM,Logh". OF got corrupted with a device tree string.
Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.
Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.
This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit af9eef3c7b caused cpu_setup to see
the_cpu_spec, rather than the source struct. However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct. So if cpu_setup patches
the feature bits, the update won't affect the fixups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a cast in case the caller passes in a different type, as it would
if mtspr/mtmsr were functions.
Previously, if a 64-bit type was passed in on 32-bit, GCC would bind the
constraint to a pair of registers, and would substitute the first register
in the pair in the asm code. This corresponds to the upper half of the
64-bit register, which is generally not the desired behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some trivial conflicts due to other various merges
adding to the end of common lists sooner than this one.
arch/ia64/Kconfig
arch/powerpc/Kconfig
arch/x86/Kconfig
lib/Kconfig
lib/Makefile
Signed-off-by: Len Brown <len.brown@intel.com>
cmpxchg() is widely used by lockless code, including NMI-safe lockless
code. But on some architectures, the cmpxchg() implementation is not
NMI-safe, on these architectures the lockless code may need a
spin_trylock_irqsave() based implementation.
This patch adds a Kconfig option: ARCH_HAVE_NMI_SAFE_CMPXCHG, so that
NMI-safe lockless code can depend on it or provide different
implementation according to it.
On many architectures, cmpxchg is only NMI-safe for several specific
operand sizes. So, ARCH_HAVE_NMI_SAFE_CMPXCHG define in this patch
only guarantees cmpxchg is NMI-safe for sizeof(unsigned long).
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Richard Henderson <rth@twiddle.net>
CC: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
CC: Yoshinori Sato <ysato@users.sourceforge.jp>
CC: Tony Luck <tony.luck@intel.com>
CC: Hirokazu Takata <takata@linux-m32r.org>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Michal Simek <monstr@monstr.eu>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: Kyle McMartin <kyle@mcmartin.ca>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Chen Liqin <liqin.chen@sunplusct.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.
This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
It is not necessary to share the same notifier.h.
This patch already moves register_reboot_notifier() and
unregister_reboot_notifier() from kernel/notifier.c to kernel/sys.c.
[amwang@redhat.com: make allyesconfig succeed on ppc64]
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.
Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.
Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.
The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.
This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.
Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
