According to WM8731 "PD, Rev 4.9 October 2012" datasheet, when it
works in DSP mode A, LRP = 1, while works in DSP mode B, LRP = 0.
So, fix LRP for DSP mode as the datesheet specification.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
N810 audio driver has stopped working at some point. Probably when
OMAP2 was converted to common clock framework since now call to clk_enable
dumps the stack trace in drivers/clk/clk.c: __clk_enable() due
clk->prepare_count is zero.
Fix this by converting clk_enable/_disable calls to those that take care
of clock prepare/unprepare.
I'm not queueing this to linux-stable since OMAP2 common clock framework
conversion in commit ed1ebc4948 ("ARM: OMAP2: clock: Convert to common clk")
happened before N810 was really usable in mainline and user base for N810 is
anyway small. Potential linux-stable candidates are only those after
commit 3d3a6d18ab ("watchdog: introduce retu_wdt driver").
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
platform_set_drvdata(op, pdata) in pcm030_fabric_probe()
will be overwrited when calling snd_soc_register_card(card),
but cm030_fabric_remove() use drvdata as a type of struct
pcm030_audio_data, so we should move platform_set_drvdata()
below snd_soc_register_card() call.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Originally snd_hrtimer_callback() used iprtd->period_time for
some jiffies based estimation to determine the right moment
to call snd_pcm_period_elapsed(). As timer drifts may well be a
problem, this was changed in commit b4e82b5b78 to be based
on buffer transmission progress, using iprtd->offset and
runtime->buffer_size to calculate the amount of data since last
period had elapsed.
Unfortunately, iprtd->offset counts in bytes, while
runtime->buffer_size counts frames, so adding these to find some
delta is like comparing apples and oranges, and eventually results
in negative delta values every now and then. This is no big harm,
because it simply causes snd_pcm_period_elapsed() being called
more often than necessary, as negative delta is taken for a
large unsigned value by implicit conversion rule.
Nonetheless, the calculation is broken, so one would replace
the runtime->buffer_size by its equivalent in bytes.
But then, there are chances snd_pcm_period_elapsed() is called
late, because calculating the moment for the elapsed period
into delta is based against the iprtd->last_offset, which is not
necessarily the first byte of the period in question, but some
random byte which the FIQ handler left us with in r8/r9 by
accident. Again, negative impact is low, as there are plenty of
periods already prefilled with data, and snd_pcm_period_elapsed()
will probably be called latest when the following period is
reached. However, the calculation is conceptually broken, and we
are best off removing the clever stuff altogether.
snd_pcm_period_elapsed() is now simply called once everytime
snd_hrtimer_callback() is run, which may not be most accurate,
but at least this way we are quite sure we dont miss an end of
period. There is not much extra effort wasted by superfluous
calls to snd_pcm_period_elapsed(), as the timer frequency
closely matches the period size anyway.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_bytes_put treats the data in the binary control as big endian
words, however snd_soc_bytes_get uses the endian of the host machine.
This causes the two functions to be inconsistant with how the mask is
applied on little endian machines.
This patch applies the big_endian format used in snd_soc_bytes_put to
snd_soc_bytes_get.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the setting of the register KIRKWOOD_PLAYCTL which did
always streaming on both I2S and SPDIF, ignoring the DAI ID.
The bug was introduced by the commit 75b9b65ee5
"ASoC: kirkwood: add S/PDIF support"
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the 32 bits format which is not supported by S/PDIF
output.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_pcm_limit_hw_rates() will initialize the minimum and maximum sample rate for
the PCM stream based on the rates specified in the rates field. Since we call
snd_pcm_limit_hw_rates() after soc_pcm_init_runtime_hw() it will essentially
overwrite the min and max rate set in soc_pcm_init_runtime_hw(). This may cause
the minimum or maximum rate to be set to a value outside the range of one of the
components if one of the components sets either SNDRV_PCM_RATE_CONTINUOUS or
SNDRV_PCM_RATE_KNOT and the other component specified a discrete rate via
SNDRV_PCM_RATE_[0-9]* that is outside of the first component's rate range. To
fix this first calculate the minimum and maximum rates using
snd_pcm_limit_hw_rates() and then on top of that apply the contraints specified
in the snd_soc_pcm_stream structs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Takashi iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make sure that the sample rate is in the supported range of both
components the maximum rate of the card should be the minimum of the maximum
rate of each components. There is one special case to consider though, if
max_rate is set to 0 this means there is no maximum specified, so use
min_not_zero() macro which will give use the desired result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Takashi iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These are managed automatically in current revisions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As the priv is not assigned to card->drvdata, it is NULL, so when
unload module, it will cause NULL pointer oops.
Assign priv to card->drvdata to fix this issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise we'll skip sync on resume.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
55e5b6fd5a
(ASoC: rsnd: use regmap instead of original register mapping method)
support regmap/regmap_field on Renesas sound driver.
It needs CONFIG_REGMAP now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zoMb
-----END PGP SIGNATURE-----
Merge tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull second set of sound fixes from Takashi Iwai:
"A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too"
* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
ALSA: hda - Provide missing pin configs for VAIO with ALC260
ALSA: hda - Add headset quirk for Dell Inspiron 3135
ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
ALSA: hda - Fix missing bass speaker on ASUS N550
ALSA: hda - Fix unbalanced runtime PM notification at resume
ASoC: arizona: Set FLL to free-run before disabling
ALSA: hda - A casual Dell Headset quirk
ASoC: rcar: fixup dma_async_issue_pending() timing
ASoC: rcar: off by one in rsnd_scu_set_route()
ASoC: wm5110: Add post SYSCLK register patch for rev D chip
ASoC: ab8500: Revert to using custom I/O functions
ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
ASoC: rcar: fixup mod access before checking
A bunch of device specific fixes, nothing with a general impact here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSjg2iAAoJELSic+t+oim93rEP/jlEjrXx8bT3acN7u/Yl/4yM
OiTG2NVHieXgzc5aux4/egjyI1mowOmQ/T2FR35oHg14jZVP8lnHYx5s6BqyDgKl
U4WdLDsUBdQYUDYkNnv93JzoI81fBuRjpRfyfLfJ39L+7gjlJgZ8uhAf0nSAir6o
7MjjPP8Ue6fJ8/uDOojLeTnZIy2blvVnENqDn8Czs9XIr/G9UnCJqYZNFzhU15Fx
m66HnfsBO3vZofe8W3N6WcZeoBW0VR1iHTKMh6Emz01U3D4Q0bmTGOFOhcP0a/Wp
Jo7SScdZoGJeGAak5x+HQjs0vLT/R867KCQap6+iK7BdrIcNwoo5HArYFC8YQ3Kt
Mqif5HNzwRBMvYKzZnDpmQMY08KSCzLrht3rI05JUEPzIgJgaAsJCLXMLxWZFfE3
kpc4EsukQujvPMKcuPbKtfNXDFvH0HyEwl0RVaEL3AuyrQM7KEvmCdNejjkQkc6s
BvmkxPNH6Ch6n0tmDcvMdB7ARBYZFi+dkjyYpvmbHqFieoEBESUKGQ+ZetvWgWC9
jkHM+xWvdAuRTCO4Iw9lo6+H19bkCLWw3S8mVPNwRO8CyW6k/x6cog7luALPnH1d
KdUHXc18d8SGgXwLwYncUSBkDspzuPJd4McXfhUNPK2cG0YVq5JMJQKFOSdqTDuu
xWWS/zqm83K4aE7IBVjc
=oSm9
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.13
A bunch of device specific fixes, nothing with a general impact here.
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
The FLL must be placed into free-run mode before disabling
to allow it to entirely shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
DMAEngine will stall without this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If "id == ARRAY_SIZE(routes)" then we read one space beyond the end of
the routes[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain registers require patching after the SYSCLK has been brought up
add support for this into the CODEC driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
It's been reported that these break audio on Snowball so revert them
until a Snowball user has time to investigate.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
rsnd_dai_connect() is using mod before NULL checking.
This patch fixes it up
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lXBM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes"
* tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - load EQ params into IDT codec on HP bNB13 systems
ASoC: cs42l52: Correct MIC CTL mask
ASoC: wm8962: Turn on regcache_cache_only before disabling regulator
ALSA: jack: Unregister input device at disconnection
ALSA: pcsp: Fix the order of input device unregistration
ASoC: fsl: imx-pcm-fiq: omit fiq counter to avoid harm in unbalanced situations
ASoC: blackfin: Fix missing break
ALSA: usb-audio: add front jack channel selector for EMU0204
ALSA: hda - Don't clear the power state at snd_hda_codec_reset()
ASoC: arizona: Fix typo in name of EQ coefficient controls
ALSA: hda - Control EAPD for Master volume on Lenovo N100
ALSA: hda - Don't turn off EAPD for headphone on Lenovo N100
ALSA: isa: not allocating enough space
ALSA: snd-aoa: two copy and paste bugs
ASoC: wm8997: Correct typo in ISRC mux routes
ALSA: hda - Check keep_eapd_on before inv_eapd
ALSA: hda - Fix Line Out automute on Realtek multifunction jacks
ALSA: msnd: Avoid duplicated driver name
ALSA: compress_core: don't return -EBADFD from poll if paused
ALSA: hda - hdmi: Fix wrong baseline length in ATI/AMD generated ELD
...
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=qcIh
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.13
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
The mask for CS42L52_MIC_CTL_TYPE_MASK was wrong keeping the mic config
from being set correctly.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's safer to turn on regcache_cache_only before disabling regulator since
the driver will turn off the regcache_cache_only after enabling regulator.
If we remain cache_only false, some command like 'amixer cset' would get
failure if being run before wm8962_resume().
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Unbalanced calls to snd_imx_pcm_trigger() may result in endless
FIQ activity and thus provoke eternal sound. While on the first glance,
the switch statement looks pretty symmetric, the SUSPEND/RESUME
pair is not: the suspend case comes along snd_pcm_suspend_all(),
which for fsl/imx-pcm-fiq is called only at snd_soc_suspend(),
but the resume case originates straight from the SNDRV_PCM_IOCTL_RESUME.
This way userland may provoke an unbalanced resume, which might cause
the fiq_enable counter to increase and never return to zero again,
so eventually imx_pcm_fiq is never disabled.
Simply removing the fiq_enable will solve the problem, as long as
one never goes play and capture game simultaneously, but beware
trying both at once, the early TRIGGER_STOP will cut off the other
activity prematurely. So now playing and capturing is scrutinized
separately, instead of by counting.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
