* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux: (42 commits)
nfsd: remove pointless paths in file headers
nfsd: move most of nfsfh.h to fs/nfsd
nfsd: remove unused field rq_reffh
nfsd: enable V4ROOT exports
nfsd: make V4ROOT exports read-only
nfsd: restrict filehandles accepted in V4ROOT case
nfsd: allow exports of symlinks
nfsd: filter readdir results in V4ROOT case
nfsd: filter lookup results in V4ROOT case
nfsd4: don't continue "under" mounts in V4ROOT case
nfsd: introduce export flag for v4 pseudoroot
nfsd: let "insecure" flag vary by pseudoflavor
nfsd: new interface to advertise export features
nfsd: Move private headers to source directory
vfs: nfsctl.c un-used nfsd #includes
lockd: Remove un-used nfsd headers #includes
s390: remove un-used nfsd #includes
sparc: remove un-used nfsd #includes
parsic: remove un-used nfsd #includes
compat.c: Remove dependence on nfsd private headers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ppc440spe-adma: adds updated ppc440spe adma driver
iop-adma.c: use resource_size()
dmaengine: clarify the meaning of the DMA_CTRL_ACK flag
sh: stylistic improvements for the DMA driver
dmaengine: fix dmatest to verify minimum transfer length and test buffer size
sh: DMA driver has to specify its alignment requirements
Add COH 901 318 DMA block driver v5
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (116 commits)
V4L/DVB (13698): pms: replace asm/uaccess.h to linux/uaccess.h
V4L/DVB (13690): radio/si470x: #include <sched.h>
V4L/DVB (13688): au8522: modify the attributes of local filter coefficients
V4L/DVB (13687): cx231xx: use NULL when pointer is needed
V4L/DVB: Davinci VPFE Capture: remove unused #include <linux/version.h>
V4L/DVB (13685): Correct code taking the size of a pointer
V4L/DVB (13684): Fix some cut-and-paste noise in dib0090.h
V4L/DVB (13683): sanio-ms: clean up init, exit and id_table
V4L/DVB (13682): dib8000: make some constant static
V4L/DVB: lgs8gxx: Use shifts rather than multiply/divide when possible
V4L/DVB (13680b): DocBook/media: create links for included sources
V4L/DVB (13680a): DocBook/media: copy images after building HTML
V4L/DVB (13678): Add support for yet another DvbWorld, TeVii and Prof USB devices
V4L/DVB (13676): configurable IRQ mode on NetUP Dual DVB-S2 CI; IRQ from CAM processing (CI interface works faster)
V4L/DVB (13674): stv090x: Add DiSEqC envelope mode
V4L/DVB (13673): lnbp21: Implement 22 kHz tone control
V4L/DVB (13671): sh_mobile_ceu_camera: Remove frame size page alignment
V4L/DVB (13670): soc-camera: Add mt9t112 camera driver
V4L/DVB (13669): tw9910: Add sync polarity support
V4L/DVB (13668): tw9910: remove cropping
...
Using create_proc_entry() + ->proc_fops assignment is racy because
->proc_fops will be NULL for some time, use proc_create() to avoid race.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Example is outdated, it still uses old ->read_proc interfaces and "fb"
example is plain racy. There are better examples all over the tree.
Docbook itself says almost nothing about /proc and contain quite a number
of simply wrong facts, e.g. device nodes support. What it does is
describing at great length interface which are going to be removed.
There are Documentation/filesystems/seq_file.txt in exchange.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Erik Mouw <mouw@nl.linux.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a patch adds ioctls, then Documentation/ioctl/ioctl-number.txt
should also be updated.
Remove reference to the OSDL PLM build farm.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now support the VX855, and the VX800 is no longer unaccellerated.
viafb_video_dev was removed as it was useless.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers may use gpiolib sysfs as part of their public user space
interface. The GPIO number and polarity might change from board to
board. The gpio_export_link() call can be used to hide the GPIO number
from user space. Add support for also hiding the GPIO line polarity
changes from user space.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For embedded systems, the blinking cursor at startup time can be annoying
and unintended. Add a new kernel parameter to change the default cursor
shape.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: David Newall <davidn@davidnewall.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If docs are being built in a separate directory, xmlto and xsltproc
can't find included sources. Make links back to the source directory.
I would much prefer to have xmlto and xsltproc look in the source
directory for included entities but couldn't see how to do that. This
needs to be solved in some way for 2.6.32, even if this patch isn't the
right way to do it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The rule for %.html removes the output directory, so there is no point
in copying images before building HTML.
Documentation/DocBook/Makefile | 10 +++++-----
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh_mobile_ceu_camera driver implements an advanced algorithm, combining
scaling and cropping on the client and on the host. Due to its complexity the
algorithm deserves separate documentation.
create mode 100644 Documentation/video4linux/sh_mobile_ceu_camera.txt
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the basic ALSA mixer functionality. The mixer is event-driven,
and will work fine on IBM ThinkPads. I expect Lenovo ThinkPads will
cause some trouble with the event interface.
Heavily based on work by Lorne Applebaum <lorne.applebaum@gmail.com>
and ideas from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lorne Applebaum <lorne.applebaum@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disable volume control by default. It can be enabled at module load
time by a module parameter (volume_control=1).
The audio control mixer that thinkpad-acpi interacts with is fully
functional without any drivers, and operated by hotkeys.
The idea behind the console audio control is that the human operator
is the only one that can interact with it. The ThinkVantage suite in
Windows does not allow any software-based overrides, and only does OSD
(on-screen-display) functions.
The Linux driver will, with the addition of the ALSA interface, try to
follow and enforce the ThinkVantage UI design:
The user is supposed to use the keyboard hotkeys to interact with the
console audio control. The kernel and the desktop environment is
supposed to cooperate to provide proper user feedback through
on-screen-display functions.
Distros are urged to not to enable volume control by default.
Enabling this must be a local admin's decision. This is the reason
why there is no Kconfig option.
Keep in mind that all ThinkPads have a normal, main mixer (AC97 or
HDA) for regular software-based audio control. We are not talking
about that mixer here.
Advanced users are, of course, free to enable volume control and do as
they please.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lorne Applebaum <lorne.applebaum@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lenovo removed the extra mixer since the T61 and thereabouts.
Newer Lenovo models only have the mute gate function, and leave
the volume control to the HDA mixer.
Until a way to automatically query the firmware about its audio
control capabilities is discovered (there might not be any), use a
white/black list.
We will likely need to ask T60 (old and new model) and Z60/Z61 users
whether they have volume control to populate the black/white list.
Meanwhile, provide a volume_capabilities parameter that can be used to
override the defaults.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lorne Applebaum <lorne.applebaum@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I don't trust the coupled EC writes and SMI calls the current volume
control code does very much, although it is exactly what the IBM DSDTs
seem to do (they never do more than a single step though).
Change the driver to stop issuing SMIs, and just drive the EC directly
to the desired level (DSDTs seem to confirm this will work even on
very old models like the 570 and 600e/x).
We checkpoint directly to NVRAM (this can be turned off) at
suspend/shutdown/driver unload, which from what I can see in tbp,
should also work on every ThinkPad.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lorne Applebaum <lorne.applebaum@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
During review of Video Timing API documentation, Hans Verkuil had a comment
on adding EBUSY error code for VIDIOC_S_STD and VIDIOC_QUERYSTD ioctls. This
patch updates the document for this.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch updates the v4l2-dvb documentation for the new video timings API added.
Also updated the document based on comments from Hans Verkuil.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers access the device number (video_device::v4l2_devnode::num)
in order to print the video device node name. Add and use a helper
function to retrieve the video_device node name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
dm snapshot: use merge origin if snapshot invalid
dm snapshot: report merge failure in status
dm snapshot: merge consecutive chunks together
dm snapshot: trigger exceptions in remaining snapshots during merge
dm snapshot: delay merging a chunk until writes to it complete
dm snapshot: queue writes to chunks being merged
dm snapshot: add merging
dm snapshot: permit only one merge at once
dm snapshot: support barriers in snapshot merge target
dm snapshot: avoid allocating exceptions in merge
dm snapshot: rework writing to origin
dm snapshot: add merge target
dm exception store: add merge specific methods
dm snapshot: create function for chunk_is_tracked wait
dm snapshot: make bio optional in __origin_write
dm mpath: reject messages when device is suspended
dm: export suspended state to targets
dm: rename dm_suspended to dm_suspended_md
dm: swap target postsuspend call and setting suspended flag
dm crypt: add plain64 iv
...
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to feature-removal-schedule.txt, it is the time to remove
print_fn_descriptor_symbol().
And a quick grep shows that it no longer has any callers.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver supports the non-volatile digital potentiometers via I2C:
AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, and AD5255
It provides a sysfs interface to each device for reading/writing which
is documented in Documentation/misc-devices/ad525x_dpot.txt.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a thread's comm to be something unique is a very useful ability
and is helpful for debugging complicated threaded applications. However
currently the only way to set a thread name is for the thread to name
itself via the PR_SET_NAME prctl.
However, there may be situations where it would be advantageous for a
thread dispatcher to be naming the threads its managing, rather then
having the threads self-describe themselves. This sort of behavior is
available on other systems via the pthread_setname_np() interface.
This patch exports a task's comm via proc/pid/comm and
proc/pid/task/tid/comm interfaces, and allows thread siblings to write to
these values.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Mike Fulton <fultonm@ca.ibm.com>
Cc: Sean Foley <Sean_Foley@ca.ibm.com>
Cc: Darren Hart <dvhltc@us.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NOMMU code currently clears all anonymous mmapped memory. While this
is what we want in the default case, all memory allocation from userspace
under NOMMU has to go through this interface, including malloc() which is
allowed to return uninitialized memory. This can easily be a significant
performance penalty. So for constrained embedded systems were security is
irrelevant, allow people to avoid clearing memory unnecessarily.
This also alters the ELF-FDPIC binfmt such that it obtains uninitialised
memory for the brk and stack region.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that ksm pages are swappable, and the known holes plugged, remove
mention of unswappable kernel pages from KSM documentation and comments.
Remove the totalram_pages/4 initialization of max_kernel_pages. In fact,
remove max_kernel_pages altogether - we can reinstate it if removal turns
out to break someone's script; but if we later want to limit KSM's memory
usage, limiting the stable nodes would not be an effective approach.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Izik Eidus <ieidus@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wright <chrisw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Describe NUMA node symlink created for CPUs when CONFIG_NUMA is set.
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c04fc586c (mm: show node to memory section relationship with
symlinks in sysfs) created symlinks from nodes to memory sections, e.g.
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
If you're examining the memory section though and are wondering what node
it might belong to, you can find it by grovelling around in sysfs, but
it's a little cumbersome.
Add a reverse symlink for each memory section that points back to the
node to which it belongs.
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register per node hstate attributes only for nodes with memory. As
suggested by David Rientjes.
With Memory Hotplug, memory can be added to a memoryless node and a node
with memory can become memoryless. Therefore, add a memory on/off-line
notifier callback to [un]register a node's attributes on transition
to/from memoryless state.
N.B., Only tested build, boot, libhugetlbfs regression.
i.e., no memory hotplug testing.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register per node hstate sysfs attributes only for nodes with memory.
Global replacement of 'all online nodes" with "all nodes with memory" in
mm/hugetlb.c. Suggested by David Rientjes.
A subsequent patch will handle adding/removing of per node hstate sysfs
attributes when nodes transition to/from memoryless state via memory
hotplug.
NOTE: this patch has not been tested with memoryless nodes.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the kernel huge tlb documentation to describe the numa memory
policy based huge page management. Additionaly, the patch includes a fair
amount of rework to improve consistency, eliminate duplication and set the
context for documenting the memory policy interaction.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system with large amount of memory (256GB), invoking page-types can
take quite a long time, which is unreasonable considering the user only
wants a description of the flags:
# time ./page-types -d 0x10
0x0000000000000010 ____D_____________________________ dirty
real 0m34.285s
user 0m1.966s
sys 0m32.313s
This is because we still walk the entire address range.
Exiting early seems like a reasonble solution:
# time ./page-types -d 0x10
0x0000000000000010 ____D_____________________________ dirty
real 0m0.007s
user 0m0.001s
sys 0m0.005s
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Haicheng Li <haicheng.li@intel.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align the output when page-type -h is invoked.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach page-types to describe page flags directly from the command line.
Why is this useful? For instance, if you're using memory hotplug and see
this in /var/log/messages:
kernel: removing from LRU failed 3836dd0/1/1e00000000000010
It would be nice to decode those page flags without staring at the source.
Example usage and output:
# Documentation/vm/page-types -d 0x10
0x0000000000000010 ____D_____________________________ dirty
# Documentation/vm/page-types -d anon
0x0000000000001000 ____________a_____________________ anonymous
# Documentation/vm/page-types -d anon,0x10
0x0000000000001010 ____D_______a_____________________ dirty,anonymous
[achiang@hp.com: documentation]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Haicheng Li <haicheng.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If not signed, testing of the read() return value in this function
will not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
