The error_debugfs label is only used when either
CONFIG_USB_DWC2_PERIPHERAL or CONFIG_USB_DWC2_DUAL_ROLE is enabled. Add
the same #if to the error_debugfs label itself as the code which uses
this label already has.
This avoids the following compiler warning:
warning: label ‘error_debugfs’ defined but not used [-Wunused-label]
Fixes: e1c08cf231 ("usb: dwc2: Add missing cleanups when usb_add_gadget_udc() fails")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit bc0f0d4a58.
It was not meant to be applied yet.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To avoid lot of interrupts from dwc2 core, which can be asserted in
specific conditions need to disable interrupts on HW level instead of
disable IRQs on Kernel level, because of IRQ can be shared between
drivers.
Cc: stable@vger.kernel.org
Fixes: a40a00318c ("usb: dwc2: add shutdown callback to platform variant")
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3 ("usb: dwc2: Move gadget probe function into platform code")
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from core version 4.20a Core Reset flow is changed.
Introduced new bit in GRSTCTL register - GRSTCTL_CSFTRST_DONE.
Core Reset new programming flow steps are follow:
1. Set GRSTCTL_CSFTRST bit.
2. Wait for bit GRSTCTL_CSFTRST_DONE is set.
3. Clear GRSTCTL_CSFTRST and GRSTCTL_CSFTRST_DONE bits.
Check core version functionality separated from dwc2_get_hwparams() to
new dwc2_check_core_version() function because Core Reset flow depend
on SNPSID.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200323160612.17277-5-zhengdejin5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't confuse user with meaningless warning about the failure in getting
supplies in case of deferred probe.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a new parameter to activate external ID pin and valid
vbus level detection, required on STM32MP15 SoC to support dual role,
either in HS or FS.
The STM32MP15 SoC uses the GGPIO register to enable the level detection.
The level detector requires to be powered.
Also adds the params structures for STM32MP15 OTG HS and STM32MP1 OTG FS.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
-----BEGIN PGP SIGNATURE-----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=3HLl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
If the 'snps,need-phy-for-wake' is set in the device tree then:
- We know that we can wakeup, so call device_set_wakeup_capable().
The USB core will use this knowledge to enable wakeup by default.
- We know that we should keep the PHY on during suspend if something
on our root hub needs remote wakeup. This requires the patch (USB:
Export usb_wakeup_enabled_descendants()). Note that we don't keep
the PHY on at suspend time if it's not needed because it would be a
power draw.
If we later find some users of dwc2 that can support wakeup without
keeping the PHY on we may want to add a way to call
device_set_wakeup_capable() without keeping the PHY on at suspend
time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting params.phy_utmi_width in dwc2_lowlevel_hw_init() is pointless since
it's value will be overwritten by dwc2_init_params().
This change make sure to take in account the generic PHY width information
during paraminitialisation, done in dwc2_set_param_phy_utmi_width().
By doing so, the phy_utmi_width params can still be overrided by
devicetree specific params and will also be checked against hardware
capabilities.
Fixes: 707d80f0a3 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.
Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On the rk3288 USB host-only port (the one that's not the OTG-enabled
port) the PHY can get into a bad state when a wakeup is asserted (not
just a wakeup from full system suspend but also a wakeup from
autosuspend).
We can get the PHY out of its bad state by asserting its "port reset",
but unfortunately that seems to assert a reset onto the USB bus so it
could confuse things if we don't actually deenumerate / reenumerate the
device.
We can also get the PHY out of its bad state by fully resetting it using
the reset from the CRU (clock reset unit), which does a more full
reset. The CRU-based reset appears to actually cause devices on the bus
to be removed and reinserted, which fixes the problem (albeit in a hacky
way).
It's unfortunate that we need to do a full re-enumeration of devices at
wakeup time, but this is better than alternative of letting the bus get
wedged.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.
The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.
If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.
Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.
Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().
Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added a flag to indicate that core is in hibernation,
it is used to determine the hibernation state of the core.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We better print an error in case probing of dwc2 fails on
setting the DMA coherent mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* Remove braces for one-line statements
* Add missing braces where another arm in if-statement uses braces
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replace this by statically defining a function with defaults, and just
assigning it. This will allow us to use parameters of any type and any
default value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Consolidate and move all the parameter initialization code from the
probe function to params.c.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a params.c file and move all driver parameter code there, including
all the static parameter definitions.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Allow for platforms that have a reset controller driver in place to bring
the USB IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleanup in probe if we fail to get dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As documented in dwc2_calculate_dynamic_fifo(), host_rx_fifo_size should
really be:
2 * ((Largest Packet size / 4) + 1 + 1) + n
with n = number of host channel.
We have 9 host channels, so
2 * ((1024/4) + 2) + 9 = 516 + 9 = 525
We've got 960 / 972 total_fifo_size on rk3288 (and presumably on
rk3066) and 525 + 128 + 256 = 909 so we're still under on both ports
even when we increment by 5.
In the future, it would be nice if dwc2_calculate_dynamic_fifo() could
handle the "too small" FIFO case and come up with something more
dynamically. When we do that we can figure out how to allocate the
extra 48 / 60 bytes of FIFO that we're currently wasting.
NOTE: no known bugs are fixed by this patch, but it seems like a simple
fix and ought to fix someone.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously we needed to set the max_transfer_size to explicitly be 65535
because the old driver would detect that our hardware could support much
bigger transfers and then would try to do them. This wouldn't work
since the DMA alignment code couldn't support it.
Later in commit e8f8c14d9d ("usb: dwc2: clip max_transfer_size to
65535") upstream added support for clipping this automatically. Since
that commit it has been OK to just use "-1" (default), but nobody
bothered to change it.
Let's change it to default now for two reasons:
- It's nice to use autodetected params.
- If we can remove the 65535 limit, we can transfer more!
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 263b7fb557 ("usb: dwc2: Move reset into
dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB
ethernet fails, due to being unable to pick up proper parameters when
performing a plain reset before reading hw params.
Below shows the results of the gnptxfsiz and hptxfsiz with and before
and after reverting this (from Stefan Wahren):
So here is the probe result before Patch 1 is applied:
[ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000
[ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000
[ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 1.394249] dwc2 20980000.usb: DWC OTG Controller
[ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000
And here is the probe result after Patch 1 is applied:
[ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000
[ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000
[ 1.434301] dwc2 20980000.usb: DWC OTG Controller
[ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset already happens before this so just force the dr_mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The reset is required to get reset values of the hardware parameters but
the force mode is not. Move the base reset into dwc2_get_hwparams() and
do the reset and force mode afterwards.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dr_mode parameter was being checked against how the dwc2 module
was being configured at compile time. But it wasn't checked against
the hardware capabilities, nor were the hardware capabilities checked
against the compilation parameters.
This commit adds those checks and adjusts dr_mode to an appropriate
value, if needed. If the hardware capabilities and module compilation
do not match then we fail as it wouldn't be possible to run properly.
The hardware, module, and dr_mode, can each be set to host, device,
or otg. Check that all these values are compatible and adjust the
value of dr_mode if possible.
The following table summarizes the behavior:
actual
HW MOD dr_mode dr_mode
------------------------------
HST HST any : HST
HST DEV any : ---
HST OTG any : HST
DEV HST any : ---
DEV DEV any : DEV
DEV OTG any : DEV
OTG HST any : HST
OTG DEV any : DEV
OTG OTG any : dr_mode
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
