On some cases, xc2028/xc3028 wents into "turn off" mode. It seems that this
happens when very weak signals are tuned. To solve this, specific standard
reaload were done previously. Christopher patches changed this behavior to a
complete firmware reload.
This patch removes the hack. A much cleaner solution for this trouble is just
to sent a xc2028/3028 software reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc3028 can be used on some DTV only designs (for example, DVB-S boards). Before
this patch, a DTV only board would need to call set_tuner_config callback.
This patch allows to optionally pass a xc3028_ctrl parameter, via xc3028_config
struct, fully initializing the driver for DTV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.
It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.
Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV. Mask them off when finding
the firmware to load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading BASE firmware, we must use std = 0.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In practice, the tuner occasionally fails to respond correctly after a
firmware load. Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs. By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware. This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.
Add a structure to remember what firmware properties we have. This
contains the currently loaded/wanted base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.
Incorporate said structure into the tuner private data.
When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible. This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no need to duplicate the max_len field from the ctrl structure
in the private data. If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.
Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.
Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops. Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The frequency divisor should only be four bytes long. Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hold the private lock over set_config and set priv->firm_size to 0 after a
failed firmware load to prevent firmware accidentally being freed on us.
Clean up the firmware load/error messages somewhat and rename priv->version
to priv->firm_version to make it clear which "version" it is.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add break to stop us from following the default failure path even upon success.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Protect refcount changes and modifications to xc2028_list with a mutex.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cast v4l2_std_id variables to unsigned long long so they will printk properly.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix some missing spaces in errors that may be emitted during attach failure.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Issuing register reads as a separate address write and data read transactions
means that other I2C activity could occur in between and state could get out
of sync. Issue both the write and read in a single transaction so that the
i2c layer can prevent other users accessing the bus until we are complete.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The I2C macros have side effects and send_seq could cause a return from
a function with a mutex held. Change them to behave like real functions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134-oss is deprecated for quite some time, it's the only remaining OSS
user outside of sound/oss/, and considering how few and what kind of
soundcards are left supported by OSS I hardly see any use cases left.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to read Hauppauge eeprom's was recently added to saa7134,
so we must build the tveeprom module.
Thanks to Matthias Schwarzott for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-900 requires the MTS version of the xc3028 firmware in order
to get any sound. The below patch selects this firmware variant on
HVR-900 cards, as well as splitting the HVR-950 into its own entry
(since I don't know if it uses the MTS variant and it will have to be
split off eventually anyway).
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TM5600/TM6000 needs clock reset during firmware load. This patch adds the
capability of caling a callback method for this.
Also, avoids uneeded firmware loads.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes uneeded parameters and adds an structure for passing the parameters
This patch is co-authored by Mauro Carvalho Chehab.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Increased size of dev->eedata from 128 to 256, since the Hauppauge data begins
at byte 128. This has been tested on boards with smaller eeproms, and caused
no problems.
Added comments to distinguish between the various versions of the HVR1110.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While there's no public API to define audio standard, adds a hack option for
select them. This is needed only for NICAM and A2 firmwares, since AM, BTSC and
EAIJ are already properly handled, on firmware version 2.7.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make the driver less verbose by default. It adds a debug parameter to make the
driver more verbose.
Also, error messages were using KERN_ERR level, instead of KERN_INFO.
A few printk messages were reviewed to make them more clear.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners, like xc3028, need to print error messages. Instead of declaring
local macros, create a tuner global macro for printing tuner errors.
To preserve CodingStyle on all tuner_macros, a few CodingStyle violations were
fixed at the other macros:
- lines with more than 80 columns
- two statements at the same line
The patch also removes the CodingStyle violation of having emacs declarations
inside de source code (CodingStyle chapter 18).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xceive 2028/3028 has a concept of scode/dcode.
Scode is a table of 16 values (each with 12 bytes i2c sequence).
Dcode is the entry of Scode table that should be used, given a certain
frequency.
The idea is that, depending on what frequency is selected, and according with a
country-based (or standard-based?) table, the Xceive should be "hacked" to
fine-tune that specific frequency.
By default, Scode=0 is used, for undefined frequencies. Also, Scode=0 seems to
be the most used value.
This patch adds the capability of selecting a scode. However, extra work will
be needed to allow auto-selecting the proper scode, for a given set of
frequencies.
I'm not sure what would be the proper way for implementing the dcode selection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Firmware version 2.7 has other firmware types. This patch adds the capability
for the driver to work with those newer types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a new image sensor to the sn9c102 driver.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.
Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were some vestiges of an old V4L1 I2C driver that were called by em28xx.
This patch removes this dead code, and replaces videodev.h to videodev2.h
Now, this driver doesn't require V4L1 anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uses the newer ioctl handler at videodev. This patch also cleans up some
bad logic at the driver and do CodingStyle and other cleanups at the
resulting driver.
Also, since VIDIOCMBUF were not working, the V4L1 compat code were removed.
The compat code will eventually be re-inserted, if we find a clean way for
implementing compatibility with the old API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On some situations, closing an streaming application and re-opening were
returning -EBUSY.
Uses the same locking schema also present on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
