GFX has a reset status register (PRM_GFX.RM_GFX_RSTST),
so update the GFX hwmod data with .rstst_off and .st_shift
information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This branch contains platform updates for 3.10. Among the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HXX3
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"This branch contains part 1 of the platform updates for 3.10. Among
the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
ARM: tegra: pm: fix build error w/o PM_SLEEP
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
ARM: socfpga: Add clock entries into device tree
ARM: socfpga: Enable soft reset
ARM: EXYNOS: replace cpumask by the corresponding macro
ARM: EXYNOS: handle properly the return values
ARM: EXYNOS: factor out the idle states
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
ARM: tegra: pm: remove duplicated include from pm.c
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: SAMSUNG: check processor type before cache restoration in resume
...
This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn
makes sure that sysc idle bit-fields are configured to valid state on
enable/disable callbacks.
With the recent submitted patch from Santosh Shilimkar,
"ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc"
(commit: 4a98c2d89), it is required to add sysconf
information to each valid hwmod entry, else device will not be
come out from idle state properly and leads to below kernel
crash -
[2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at
0xf9e35034
[2.198325] Internal error: : 1028 [#1] SMP ARM
[2.203101] Modules linked in:
[2.206334] CPU: 0 Not tainted (3.9.0-rc3-00059-gd114294#1)
[2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60
[2.218090] LR is at omap_wdt_probe+0x184/0x1fc
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Update the AES0 HIB2 module's hwmod data for the am33xx SoC.
Also, remove it from the '#if 0' block that its currently
inside so the data is actually available for use.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the SHA0 HIB2 module's hwmod data for the am33xx SoC.
Also, remove it from the '#if 0' block that its currently
inside so the data is actually available for use.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
struct omap_hwmod records belonging to wkup m3 domain is missing
HWMOD_NO_IDLEST flags; add them.
This patch is a prerequisite for a subsequent patch, 'ARM: OMAP2:
am33xx-hwmod: Fix "register offset NULL check" bug'. That patch would
otherwise attempt to read from reserved bits.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
[paul@pwsan.com: add some more explanation in the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As part of PWM subsystem integration, PWM subsystem are sharing
resources like clock across submodules (ECAP, EQEP & EHRPWM). To handle
resource sharing & IP integration rework on parent child relation
between PWMSS and ECAP, EQEP & EHRPWM child devices to support runtime PM.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
EQEP IP block integration data is not present in HWMOD data. Also
address ranges specified for EACP & EHRPWM are not correct & HWMOD
flags of ADDR_TYPE_RT are added to PWM subsystem register address
space. This patch:
1. Corrects register address mapping for ECAP & EHRPWM
2. Removes HWMOD flags in PWM submodule register address space.
3. Adds EQEP HWMOD entries.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
WKUP-M3 has a reset status bit (RM_WKUP_STST.WKUP_M3_LRST)
Update the WKUP-M3 hwmod data to reflect the same.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The current HWMOD code expects the memory region with
the IP's SYSCONFIG register to be marked with ADDR_TYPE_RT
flag.
CPGMAC0 hwmod entry specifies two memory regions and marks
both with the flag ADDR_TYPE_RT although only the 2nd region
has the SYSCONFIG register. This leads to the HWMOD code
accessing the wrong memory address for idle and standby
operations. Fix this by removing the ADDR_TYPE_RT flag from
the 1st memory region in CPGMAC0 hwmod entry.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Third Party Transfer Controller (TPTC0) needs to be idled and
put to standby under SW control. Add the appropriate flags in
the TPTC0 hwmod entry.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OCMC RAM lies in the PER power domain and this memory
support retention.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START
This led to having a resource list of 100s of IRQs.
Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add
AM33XX HWMOD data) that probably had some search and replace updates
done for the patch for sparse irq support.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated wit information about the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 70384a6af0 ("ARM: OMAP3+:
hwmod: Add AM33XX HWMOD data for davinci_mdio module") adds two
new sparse warnings:
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2518:30: warning: symbol 'am33xx_mdio_addr_space' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2526:26: warning: symbol 'am33xx_cpgmac0__mdio' was not declared. Should it be static?
Fix by marking the two new records as static.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds hwmod entry for davinci MDIO module,
creating parent<->child relationship between CPSW and MDIO module.
This Parent-child relation is required in order to use common resources
like, clock, but still maintaining the logical separation between them.
CPGMAC SubSystem consist of various sub-modules, like, mdio, cpdma,
cpsw, etc... These sub-modules are also used in some of Davinci
family of devices, so separate and independent platform devices &
drivers for CPSW and MDIO is implemented.
In case of AM33XX, the resources are shared and common register
bit-field is provided to control module/clock enable/disable,
makes it difficult to handle common resources from both drivers.
So the solution is, create parent<->child relationship between
CPGMAC & MDIO modules.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to remove this from plat for ARM common zImage
support.
Also remove includes not needed by the omap_hsmmc.c driver.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Venkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM33xx hwmod data includes "mcspi.h" which has now been moved after
the platform_data move. Fix it.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
should now boot on mainline after this is applied, according to
Vaibhav.
This second version includes trailing commas at the end of structure
records at Tony's request. It also adds a OMAP_INTC_START macro
expansion to each IRQ number to make the sparseirq conversion easier.
Basic build, boot, and PM test transcripts are here:
http://www.pwsan.com/omap/testlogs/am33xx_hwmod_clock_devel_3.7/20120912165952/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yRjp
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-a2-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-am33xx
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
This second version includes trailing commas at the end of structure
records at Tony's request. It also adds a OMAP_INTC_START macro
expansion to each IRQ number to make the sparseirq conversion easier.
Basic build, boot, and PM test transcripts are here:
http://www.pwsan.com/omap/testlogs/am33xx_hwmod_clock_devel_3.7/20120912165952/
This patch adds HWMOD data for all the peripherals of
AM335X device and also hooks up to the existing OMAP framework.
hwmod data has been already been cleaned up for the recent
changes in clocktree, where all leaf nodes have been removed,
since with modulemode based control, both clock and hwmod
interface does same thing. This reduces the code size to large
extent and also avoids duplication of same control.
So instead of specifying module's leaf node as a main_clk,
now we are relying on parent clock of module's functional clock.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: removed period in hwmod device names; changed mmc2 main_clk
to mmc_clk at Vaibhav's request; added trailing commas to structure
records at Tony's request to deal with some rmk parsing issues; added
OMAP_INTC_START to facilitate sparse-IRQ conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
