When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While removing the need to have pin_base defined in meson pinctrl
drivers, I forgot to remove the corresponding field from the
pinctrl_data structure.
Fixing this now.
Fixes: 70e5ecb1b9 ("pinctrl: meson: get rid of pin_base")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the Amlogic Meson8 / Meson8b platforms we have two different buses:
cbus and aobus, corresponding to 2 different power domains (regular and
always-on). On each bus a different set of registers is mapped to manage
muxes, GPIOs and in general to control a clear subset of the pins.
Considering this architecture, having two different pinctrl devices, one
for each bus / power domain, makes much more sense than just having one
single device.
Right now we have one single pin controller driver that uses two
different domains (represented by 'gpio' and 'gpio-ao' sub-nodes in the
DTS) to manage the set of registers on the two buses. This dual-domain
configuration is hardcoded into the driver that strictly requires one
domain for each bus in the same pin controller device.
With this patch we refactor the driver to allow splitting the driver in
two parts. This change is needed to have a proper description of the HW
in the device-tree where we want to introduce aobus and cbus.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the AmLogic Meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a new PIN macro and few small modifications to
simplify and shorten the Meson pinctrl drivers and cleanup the support
file for the AmLogic Meson8 SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
