Historically this was set to "keep_firmware_settings" to prevent problems
with power management on very old drives. However it's been observed that
almost all modern Linux distributions either set the policy to
"med_power_with_dipm" in the kernel configuration or update it to this via
userspace policy changes. Update the policy default in the kernel to
"med_power_with_dipm" to match that behavior as well.
Changing the default was previously not a good idea, because LPM disables
detection of hot plug removals, however, since commit ae1f3db006 ("ata:
ahci: do not enable LPM on external ports"), a port marked as external
will always be initialized to "keep_firmware_settings", regardless of the
SATA_MOBILE_LPM_POLICY Kconfig value. Therefore, changing the default is
now considered safe (external ports included).
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[cassel: rebased and reworded commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The low power policy board type was introduced to allow systems
to get into deep states reliably. Before it was introduced `min_power`
was causing problems for a number of drives. New power policies
`min_power_with_partial` and `med_power_with_dipm` have been introduced
which provide a more stable baseline for systems.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[cassel: rebase patch and fix trivial conflicts]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The Freescale QorIQ AHCI SATA controller is only present on Freescale
Layerscape SoCs. Add platform dependencies to the AHCI_QORIQ config
symbol, to avoid asking the user about it when configuring a kernel
without Layerscape support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
* Small cleanup of the pata_octeon driver to drop a useless platform
callback, from Uwe.
* Simplify ata_scsi_cmd_error_handler() code using the fact that
ap->ops->error_handler is NULL most of the time, from Wenchao.
* Several patches improving libata error handling. This is in
preparation for supporting the command duration limits (CDL)
feature. The changes allow handling corner cases of ATA NCQ errors
which do not happen with regular drives but will be triggered with
CDL drives. From Niklas.
* Simplify the qc_fill_rtf operation, from me.
* Improve SCSI command translation for the
REPORT_SUPPORTED_OPERATION_CODES command, from me.
* Cleanup of libata FUA handling. This falls short of enabling FUA for
ATA drives that support it by default as there were concerns that
old drives would break. The series howeverfixes several issues with
the FUA support to ensure that FUA is reported as being supported
only for drives that can handle all possible write cases (NCQ and
non-NCQ). A check in the block layer is also added to ensure that we
never see read FUA commands (current behavior). From me.
* Several patches to move the old PARIDE (parallel port IDE) driver to
libata as pata_parport. Given that this driver also needs protocol
modules, the driver code resides in its own pata_parport directoy
under drivers/ata. From Ondrej.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCY/VTnQAKCRDdoc3SxdoY
dk77AQCA1frczKhcOFe2PK/FsFAiO9Nlx/snk7V95JdjVG8GlwEAkey7mvbXMfX0
fDbqpaCkWFb6SvwxdMSATlqUvwEpSQ8=
=tqQP
-----END PGP SIGNATURE-----
Merge tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
- Small cleanup of the pata_octeon driver to drop a useless platform
callback (Uwe)
- Simplify ata_scsi_cmd_error_handler() code using the fact that
ap->ops->error_handler is NULL most of the time (Wenchao)
- Several patches improving libata error handling. This is in
preparation for supporting the command duration limits (CDL) feature.
The changes allow handling corner cases of ATA NCQ errors which do
not happen with regular drives but will be triggered with CDL drives
(Niklas)
- Simplify the qc_fill_rtf operation (me)
- Improve SCSI command translation for REPORT_SUPPORTED_OPERATION_CODES
command (me)
- Cleanup of libata FUA handling.
This falls short of enabling FUA for ATA drives that support it by
default as there were concerns that old drives would break. The
series however fixes several issues with the FUA support to ensure
that FUA is reported as being supported only for drives that can
handle all possible write cases (NCQ and non-NCQ). A check in the
block layer is also added to ensure that we never see read FUA
commands (current behavior) (me)
- Several patches to move the old PARIDE (parallel port IDE) driver to
libata as pata_parport. Given that this driver also needs protocol
modules, the driver code resides in its own pata_parport directoy
under drivers/ata (Ondrej)
* tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_parport: Fix ida_alloc return value error check
drivers/block: Move PARIDE protocol modules to drivers/ata/pata_parport
drivers/block: Remove PARIDE core and high-level protocols
ata: pata_parport: add driver (PARIDE replacement)
ata: libata: exclude FUA support for known buggy drives
ata: libata: Fix FUA handling in ata_build_rw_tf()
ata: libata: cleanup fua support detection
ata: libata: Rename and cleanup ata_rwcmd_protocol()
ata: libata: Introduce ata_ncq_supported()
block: add a sanity check for non-write flush/fua bios
ata: libata-scsi: improve ata_scsiop_maint_in()
ata: libata-scsi: do not overwrite SCSI ML and status bytes
ata: libata: move NCQ related ATA_DFLAGs
ata: libata: respect successfully completed commands during errors
ata: libata: read the shared status for successful NCQ commands once
ata: libata: simplify qc_fill_rtf port operation interface
ata: scsi: rename flag ATA_QCFLAG_FAILED to ATA_QCFLAG_EH
ata: libata-eh: Cleanup ata_scsi_cmd_error_handler()
ata: octeon: Drop empty platform remove function
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
Move PARIDE protocol modules out of drivers/block into
drivers/ata/pata_parport and update the CONFIG_ symbol names to
PATA_PARPORT.
[Damien]
The pata_parport driver file itsef is also moved together with the
protocol modules in drivers/ata/pata_parport.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Remove PARIDE core and high level protocols, taking care not to break
low-level drivers (used by pata_parport). Also update documentation.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The pata_parport is a libata-based replacement of the old PARIDE
subsystem - driver for parallel port IDE devices.
It uses the original paride low-level protocol drivers but does not
need the high-level drivers (pd, pcd, pf, pt, pg). The IDE devices
behind parallel port adapters are handled by the ATA layer.
This will allow paride and its high-level drivers to be removed.
Unfortunately, libata drivers cannot sleep so pata_parport claims
parport before activating the ata host and keeps it claimed (and
protocol connected) until the ata host is removed. This means that
no devices can be chained (neither other pata_parport devices nor
a printer).
paride and pata_parport are mutually exclusive because the compiled
protocol drivers are incompatible.
Tested with:
- Imation SuperDisk LS-120 and HP C4381A (EPAT)
- Freecom Parallel CD (FRPW)
- Toshiba Mobile CD-RW 2793008 w/Freecom Parallel Cable rev.903 (FRIQ)
- Backpack CD-RW 222011 and CD-RW 19350 (BPCK6)
The following bugs in low-level protocol drivers were found and will
be fixed later:
Note: EPP-32 mode is buggy in EPAT - and also in all other protocol
drivers - they don't handle non-multiple-of-4 block transfers
correctly. This causes problems with LS-120 drive.
There is also another bug in EPAT: EPP modes don't work unless a 4-bit
or 8-bit mode is used first (probably some initialization missing?).
Once the device is initialized, EPP works until power cycle.
So after device power on, you have to:
echo "parport0 epat 0" >/sys/bus/pata_parport/new_device
echo pata_parport.0 >/sys/bus/pata_parport/delete_device
echo "parport0 epat 4" >/sys/bus/pata_parport/new_device
(autoprobe will initialize correctly as it tries the slowest modes
first but you'll get the broken EPP-32 mode)
Note: EPP modes are buggy in FRPW, only modes 0 and 1 work.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The PXA palmld machine was removed, so the pata driver is no
longer used and can be removed. There is a chance that some of
this code might be useful for turning some of the other PXA
PCMCIA host drivers into PATA drivers, but it's clear that
it would not work unmodified, and it seems unlikely that
someone would do this work.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This device was only used by the smdk6410 board file that is now
gone, so the driver can be removed as well.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This driver uses MSR functions that aren't implemented under UML.
Avoid building it to prevent tripping up allyesconfig.
e.g.
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x3a3): undefined reference to `__tracepoint_read_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x3d2): undefined reference to `__tracepoint_write_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x457): undefined reference to `__tracepoint_write_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x481): undefined reference to `do_trace_write_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x4d5): undefined reference to `do_trace_write_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x4f5): undefined reference to `do_trace_read_msr'
/usr/lib/gcc/x86_64-pc-linux-gnu/12/../../../../x86_64-pc-linux-gnu/bin/ld: pata_cs5535.c:(.text+0x51c): undefined reference to `do_trace_write_msr'
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
This device was used only on the davinci dm644x platform that
is now gone, and no references to the device remain in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The pata_ftide010 can be built without CONFIG_OF being enabled, as long
as the macro of_match_ptr() is not used when initializing the platform
driver .of_match_table field.
Remove the use of this macro and the build dependency on OF.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
If CONFIG_OF is disabled, then using the macro of_match_ptr() results
in the gemini_sata_of_match variable being unused, which generates a
compilation warning and a compilation error if CONFIG_WERROR is enabled.
Removing the use of this macro by directly assigning the
gemini_sata_of_match match table to the .of_match_table field in the
platform driver definition allows removing the dependency on OF for
compile tests, thus improving compile test coverage.
Fixes: f7220eac75 ("ata: Kconfig: fix sata gemini compile test condition")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
It's almost fully compatible DWC AHCI SATA IP-core derivative except the
reference clocks source, which need to be very carefully selected. In
particular the DWC AHCI SATA PHY can be clocked either from the pads
ref_pad_clk_{m,p} or from the internal wires ref_alt_clk_{m,n}. In the
later case the clock signal is generated from the Baikal-T1 CCU SATA PLL.
The clocks source is selected by means of the ref_use_pad wire connected
to the CCU SATA reference clock CSR.
In normal situation it would be much more handy to use the internal
reference clock source, but alas we haven't managed to make the AHCI
controller working well with it so far. So it's preferable to have the
controller clocked from the external clock generator and fallback to the
internal clock source only as a last resort. Other than that the
controller is full compatible with the DWC AHCI SATA IP-core.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Synopsys AHCI SATA controller can work pretty under with the generic
AHCI-platform driver control. But there are vendor-specific peculiarities
which can tune the device performance up and which may need to be fixed up
for proper device functioning. In addition some DWC AHCI-based controllers
may require small platform-specific fixups, so adding them in the generic
AHCI driver would have ruined the code simplicity. Shortly speaking in
order to keep the generic AHCI-platform code clean and have DWC AHCI
SATA-specific features supported we suggest to add a dedicated DWC AHCI
SATA device driver. Aside with the standard AHCI-platform resources
getting, enabling/disabling and the controller registration the new driver
performs the next actions.
First of all there is a way to verify whether the HBA/ports capabilities
activated in OF are correct. Almost all features availability is reflected
in the vendor-specific parameters registers. So the DWC AHCI driver does
the capabilities sanity check based on the corresponding fields state.
Secondly if either the Command Completion Coalescing or the Device Sleep
feature is enabled the DWC AHCI-specific internal 1ms timer must be fixed
in accordance with the application clock signal frequency. In particular
the timer value must be set to be Fapp * 1000. Normally the SoC designers
pre-configure the TIMER1MS register to contain a correct value by default.
But the platforms can support the application clock rate change. If that
happens the 1ms timer value must be accordingly updated otherwise the
dependent features won't work as expected. In the DWC AHCI driver we
suggest to rely on the "aclk" reference clock rate to set the timer
interval up. That clock source is supposed to be the AHCI SATA application
clock in accordance with the DT bindings.
Finally DWC AHCI SATA controller AXI/AHB bus DMA-engine can be tuned up to
transfer up to 1024 * FIFO words at a time by setting the Tx/Rx
transaction size in the DMA control register. The maximum value depends on
the DMA data bus and AXI/AHB bus maximum burst length. In most of the
cases it's better to set the maximum possible value to reach the best AHCI
SATA controller performance. But sometimes in order to improve the system
interconnect responsiveness, transferring in smaller data chunks may be
more preferable. For such cases and for the case when the default value
doesn't provide the best DMA bus performance we suggest to use the new
HBA-port specific DT-properties "snps,{tx,rx}-ts-max" to tune the DMA
transactions size up.
After all the settings denoted above are handled the DWC AHCI SATA driver
proceeds further with the standard AHCI-platform host initializations.
Note since DWC AHCI controller is now have a dedicated driver we can
discard the corresponding compatible string from the ahci-platform.c
module. The same concerns "snps,spear-ahci" compatible string, which is
also based on the DWC AHCI IP-core.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
It is currently possible to select "Generic platform device PATA support"
in two situations:
- architecture allows the generic platform device PATA support and
indicates that with "select HAVE_PATA_PLATFORM".
- if the user claims to be an EXPERT by setting CONFIG_EXPERT to yes
However, there is no use case to have Generic platform device PATA support
in a kernel build if the architecture definition, i.e., the selection of
configs by an architecture, does not support it.
If the architecture definition is wrong, i.e., it just misses a 'select
HAVE_PATA_PLATFORM', then even an expert that configures the kernel build
should not just fix that by overruling the claimed support by an
architecture. If the architecture definition is wrong, the expert should
just provide a patch to correct the architecture definition instead---in
the end, if the user is an expert, sending a quick one-line patch should
not be an issue.
In other words, I do not see the deeper why an expert can overrule the
architecture definition in this case, as the expert may not overrule the
config selections defined by the architecture in the large majority
---or probably all other (modulo some mistakes)---of similar cases.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
There are two options for platform device PATA support:
PATA_PLATFORM: Generic platform device PATA support
PATA_OF_PLATFORM: OpenFirmware platform device PATA support
If an architecture allows the generic platform device PATA support, it
shall select HAVE_PATA_PLATFORM. Then, Generic platform device PATA support
is available and can be selected.
If an architecture has OpenFirmware support, which it indicates by
selecting OF, OpenFirmware platform device PATA support is available
and can be selected.
If OpenFirmware platform device PATA support is selected, then the
functionality (code files) from Generic platform device PATA support needs
to be integrated in the kernel build for the OpenFirmware platform device
PATA support to work. Select PATA_PLATFORM in PATA_OF_PLATFORM to make sure
the needed files are added in the build.
So, architectures with OpenFirmware support, do not need to additionally
select HAVE_PATA_PLATFORM. It is only needed by architecture that want the
non-OF pata-platform module.
Reflect this way of intended use of config symbols in the ata Kconfig and
adjust all architecture definitions.
This follows the suggestion from Arnd Bergmann (see Link).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/all/4b33bffc-2b6d-46b4-9f1d-d18e55975a5a@www.fastmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
AHCI_BRCM depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
CONFIG_SATA_LPM_MOBILE_POLICY was renamed to CONFIG_SATA_LPM_POLICY in
commit 4dd4d3deb5 ("ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY
configuration item").
This can potentially cause problems as users would invisibly lose
configuration policy defaults when they built the new kernel. To
avoid such problems, switch back to the old name (even if it's wrong).
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
`CONFIG_SATA_LPM_MOBILE_POLICY` reflects a configuration to apply only to
mobile chipsets. As some desktop boards may want to use this policy by
default as well, rename the configuration item to `SATA_LPM_POLICY`.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
When compile testing the sata gemini driver, CONFIG_OF is required to
avoid the warning:
drivers/ata/sata_gemini.c:421:34: error: ‘gemini_sata_of_match’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable SAMSUNG_DEV_IDE.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_PXA.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_MXC.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARM.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on X86_64 && COMPILE_TEST to allow compile tests
with configs that do not have X86_32 enabled on X86_64 hosts.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_DAVINCI.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_SEATTLE.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable PHY_XGENE.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_TEGRA.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_SUNXI.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_MVEBU.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_MEDIATEK.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_OMAP2PLUS.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_DAVINCI_DA850.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add Kconfig dependendy on COMPILE_TEST to allow compile tests with
configs that do not enable ARCH_BRCMSTB, BMIPS_GENERIC or ARCH_BCM_XXX.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add dependendy on COMPILE_TEST to allow compile tests with configs that
do not enable FSL_SOC.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Driver has been converted to dynamic debugging, so the compile-time
options don't have any functionality left.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
Portable drivers cannot use mach/platform.h, so move the
structure into its own header. With this, compile testing
can be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows m68k q40 systems to switch from the deprecated IDE subsystem
to libata.
Enhance the byte-swapping falconide and pata_falcon platform drivers to
accept an irq resource, for use on q40. Atari ST-DMA IRQ arrangements seem
to co-exist with q40 IRQ arrangements without too much mess.
The new IO resources were added solely for the purpose of making
request_region() reservations identical to those made by q40ide: these
regions aren't used for actual IO.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/eefb7e9c2291e09fb4e065ce06bc105f05bb9e06.1623287706.git.fthain@linux-m68k.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Separate PATA timings code from libata-core.c:
* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) select it
* move following PATA timings code to libata-pata-timings.c:
- ata_timing_quantize()
- ata_timing_merge()
- ata_timing_find_mode()
- ata_timing_compute()
* group above functions together in <linux/libata.h>
* include libata-pata-timings.c in the build when PATA_TIMINGS
config option is enabled
* cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it
depends on code from libata-core.c and libata-pata-timings.c
while its only user is ATA ACPI)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
after:
37820 572 40 38432 9620 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no reason to expose SATA_PMP config option when no SATA
host drivers are enabled. To fix it add SATA_HOST config option,
make all SATA host drivers select it and finally make SATA_PMP
config options depend on it.
This also serves as preparation for the future changes which
optimize libata core code size on PATA only setups.
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # for SCSI bits
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add Buddha PATA controller driver. It enables libata support for
the Buddha, Catweasel and X-Surf expansion boards on the Zorro
expansion bus.
Module removal is currently unsupported (the old IDE's buddha
driver also doesn't support it).
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After commit 5d32a66541 (PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set) dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly. PATA_ACPI is a PCI device driver but the PCI
dependency has not been explicitly called out.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
