This makes a HPTE removal function, kvmppc_do_h_remove(), available
outside book3s_hv_rm_mmu.c. This will be used by the HPT writing
code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This uses a bit in our record of the guest view of the HPTE to record
when the HPTE gets modified. We use a reserved bit for this, and ensure
that this bit is always cleared in HPTE values returned to the guest.
The recording of modified HPTEs is only done if other code indicates
its interest by setting kvm->arch.hpte_mod_interest to a non-zero value.
The reason for this is that when later commits add facilities for
userspace to read the HPT, the first pass of reading the HPT will be
quicker if there are no (or very few) HPTEs marked as modified,
rather than having most HPTEs marked as modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug where adding a new guest HPT entry via the H_ENTER
hcall would lose the "changed" bit in the reverse map information
for the guest physical page being mapped. The result was that the
KVM_GET_DIRTY_LOG could return a zero bit for the page even though
the page had been modified by the guest.
This fixes it by only modifying the index and present bits in the
reverse map entry, thus preserving the reference and change bits.
We were also unnecessarily setting the reference bit, and this
fixes that too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This restructures the code that creates HPT (hashed page table)
entries so that it can be called in situations where we don't have a
struct vcpu pointer, only a struct kvm pointer. It also fixes a bug
where kvmppc_map_vrma() would corrupt the guest R4 value.
Most of the work of kvmppc_virtmode_h_enter is now done by a new
function, kvmppc_virtmode_do_h_enter, which itself calls another new
function, kvmppc_do_h_enter, which contains most of the old
kvmppc_h_enter. The new kvmppc_do_h_enter takes explicit arguments
for the place to return the HPTE index, the Linux page tables to use,
and whether it is being called in real mode, thus removing the need
for it to have the vcpu as an argument.
Currently kvmppc_map_vrma creates the VRMA (virtual real mode area)
HPTEs by calling kvmppc_virtmode_h_enter, which is designed primarily
to handle H_ENTER hcalls from the guest that need to pin a page of
memory. Since H_ENTER returns the index of the created HPTE in R4,
kvmppc_virtmode_h_enter updates the guest R4, corrupting the guest R4
in the case when it gets called from kvmppc_map_vrma on the first
VCPU_RUN ioctl. With this, kvmppc_map_vrma instead calls
kvmppc_virtmode_do_h_enter with the address of a dummy word as the
place to store the HPTE index, thus avoiding corrupting the guest R4.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In order to support the generic eventfd infrastructure on PPC, we need
to call into the generic KVM in-kernel device mmio code.
Signed-off-by: Alexander Graf <agraf@suse.de>
If the DIU framebuffer driver is not enabled, then there's no point in
compiling any platform DIU code, because it will never be used. Most of
the platform code was protected in the appropriate #ifdef, but not all.
This caused a break in some randconfig builds.
This is only a problem on the 512x platforms. The P1022DS and MPC8610HPCD
platforms are already correct.
This patch reverts commit 12e36309f8 ("powerpc:
Option FB_FSL_DIU is not really optional for mpc512x") and restores the
ability to configure DIU support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* pm-cpuidle:
cpuidle: Measure idle state durations with monotonic clock
cpuidle: fix a suspicious RCU usage in menu governor
cpuidle: support multiple drivers
cpuidle: prepare the cpuidle core to handle multiple drivers
cpuidle: move driver checking within the lock section
cpuidle: move driver's refcount to cpuidle
cpuidle: fixup device.h header in cpuidle.h
cpuidle / sysfs: move structure declaration into the sysfs.c file
cpuidle: Get typical recent sleep interval
cpuidle: Set residency to 0 if target Cstate not enter
cpuidle: Quickly notice prediction failure in general case
cpuidle: Quickly notice prediction failure for repeat mode
cpuidle / sysfs: move kobj initialization in the syfs file
cpuidle / sysfs: change function parameter
Commit c22618a1, "drivers/of: Constify device_node->name and
->path_component_name" changes device_node name to a const value, but
the PowerPC scom code still assigns it to a non-void field in
debugfs_blob_wrapper. The /right/ solution might be to change the
debugfs_blob_wrapper->data to also be const, but that is a bit
risky. Instead, cast the value to (void*). It is a bit ugly, but it
is the safest change until it can be investigated where
debugfs_blob_wrapper can be modified.
Reported-by: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Many cpuidle drivers measure their time spent in an idle state by
reading the wallclock time before and after idling and calculating the
difference. This leads to erroneous results when the wallclock time gets
updated by another processor in the meantime, adding that clock
adjustment to the idle state's time counter.
If the clock adjustment was negative, the result is even worse due to an
erroneous cast from int to unsigned long long of the last_residency
variable. The negative 32 bit integer will zero-extend and result in a
forward time jump of roughly four billion milliseconds or 1.3 hours on
the idle state residency counter.
This patch changes all affected cpuidle drivers to either use the
monotonic clock for their measurements or make use of the generic time
measurement wrapper in cpuidle.c, which was already working correctly.
Some superfluous CLIs/STIs in the ACPI code are removed (interrupts
should always already be disabled before entering the idle function, and
not get reenabled until the generic wrapper has performed its second
measurement). It also removes the erroneous cast, making sure that
negative residency values are applied correctly even though they should
not appear anymore.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge my own merge branch to get various fixes from there
and upstream, especially the hvc console tty refcouting fixes
which which testing is quite a bit harder...
While the EEH does recovery on the specific PE that has PCI errors,
the PCI devices belonging to the PE will be removed and the PE will
be marked as invalid since we still need the information stored in
the PE. We only invalidate the PE when it doesn't have associated
EEH devices and valid child PEs. However, the code used to check
that is wrong. The patch fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PAMU bypass enable register added to the ccsr_guts structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ePAPR v1.1 requires the spin table to be in cached memory. So we need
to change the call argument of ioremap to enable cache and coherence.
We also flush the cache after writing to spin table to keep it compatible
with previous cache-inhibit spin table. Flushing before and after
accessing spin table is recommended by ePAPR.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Power supply for PCI controller ATMU registers is off when system go to
deep-sleep state. So ATMU registers should be re-setup during PCI
controllers resume from sleep.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function fsl_pcibios_fixup_bus() is available only if PCI is enabled. The
MPC8610 HPCD platform file was not protecting the assigned with an #ifdef,
which results in a link failure when PCI is disabled. Every other platform
already has this #ifdef.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new EEH code introduced a small regression, if the EEH PEs
are missin (which happens currently in qemu for example), it
will deref a NULL pointer in the MSI code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
System time accounting APIs such as vtime_account_system() and
vtime_account_idle() need to be irqsafe. Current callers include
irq entry, exit and kvm, all of which have been checked against that
requirement. Now it's better to grow that with an automatic check
in case we have further callers or we missed something.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
On ia64 and powerpc, vtime context switch only consists
in flushing system and user pending time, plus a few
arch housekeeping.
Consolidate that into a generic implementation. s390 is
a special case because pending user and system time accounting
there is hard to dissociate. So it's keeping its own implementation.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
All vtime implementations just flush the user time on process
tick. Consolidate that in generic code by calling a user time
accounting helper. This avoids an indirect call in ia64 and
prepare to also consolidate vtime context switch code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Prepending irq-unsafe vtime APIs with underscores was actually
a bad idea as the result is a big mess in the API namespace that
is even waiting to be further extended. Also these helpers
are always called from irq safe callers except kvm. Just
provide a vtime_account_system_irqsafe() for this specific
case so that we can remove the underscore prefix on other
vtime functions.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
The expressions tsk->nsproxy->pid_ns and task_active_pid_ns
aka ns_of_pid(task_pid(tsk)) should have the same number of
cache line misses with the practical difference that
ns_of_pid(task_pid(tsk)) is released later in a processes life.
Furthermore by using task_active_pid_ns it becomes trivial
to write an unshare implementation for the the pid namespace.
So I have used task_active_pid_ns everywhere I can.
In fork since the pid has not yet been attached to the
process I use ns_of_pid, to achieve the same effect.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF PowerPC JIT parts for the BPF XOR operation.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither of these should ever be changed once set. Make them const and
fix up the users that try to modify it in-place. In one case
kmalloc+memcpy is replaced with kstrdup() to avoid modifying the string.
Build tested with defconfigs on ARM, PowerPC, Sparc, MIPS, x86 among
others.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Julian Calaby <julian.calaby@gmail.com>
Since we don't know if they new kernel we are kexecing into has been
built to support relocation on exceptions, we disable them before we
kexec.
We do NOT disable them if we are execing a kdump kernel, because we
want to change as little state as possible and it is likely that we are
execing ourselves and will be able to handle them anyway.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently do this synchronously at boot from setup_arch. On a large
system this could hypothetically take a little while to complete, so
currently we will give up if we are asked to wait for more than a second
in total.
If we actually start hitting that timeout in practice we can always move
this code into a kernel thread to take care of it in the background.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I am going to use this in the next patch, better to have this code in
one place rather than three.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These wrappers hide the parameters that have to be passed to H_SET_MODE
to enable/disable relocation on during exceptions.
As noted in the comments, since these have partition wide scope, they
may take some time to complete and must be periodically retried until
H_SUCCESS is returned.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This new hcall in POWER8 is used to set various resource mode registers.
eg. it can set address translation mode on interrupt (note: partition wide
scope)
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This turns on MMU on execptions via AIL field in the LPCR.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want to change what's initially set in the LPCR, so start by taking the move
from LPCR out of the function and into the caller.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8/v2.07 allows exceptions to be taken with the MMU still on.
A new set of exception vectors is added at 0xc000_0000_0000_4xxx. When the HW
takes us here, MSR IR/DR will be set already and we no longer need a costly
RFID to turn the MMU back on again.
The original 0x0 based exception vectors remain for when the HW can't leave the
MMU on. Examples of this are when we can't trust the current MMU mappings,
like when we are changing from guest to hypervisor (HV 0 -> 1) or when the MMU
was off already. In these cases the HW will take us to the original 0x0 based
exception vectors with the MMU off as before.
This uses the new macros added previously too implement these new execption
vectors at 0xc000_0000_0000_4xxx. We exit these exception vectors using
mflr/blr (rather than mtspr SSR0/RFID), since we don't need the costly MMU
switch anymore.
This moves the __end_interrupts marker down past these new 0x4000 vectors since
they will need to be copied down to 0x0 when the kernel is not at 0x0.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8/v2.07 allows exceptions to be taken with the MMU still on.
A new set of exception vectors is added at 0xc000_0000_0000_4xxx. When the HW
takes us here, MSR IR/DR will be set already and we no longer need a costly
RFID to turn the MMU back on again.
The original 0x0 based exception vectors remain for when the HW can't leave the
MMU on. Examples of this are when we can't trust the current the MMU mappings,
like when we are changing from guest to hypervisor (HV 0 -> 1) or when the MMU
was off already. In these cases the HW will take us to the original 0x0 based
exception vectors with the MMU off as before.
The below macros are copies of the macros used at the 0x0 offset but modified
to handle the MMU being on. In these macros we use the link register to jump
to the secondary handlers rather than using RFID (RFID was also use to turn on
the MMU).
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This turns the syscall handler into macros as we are going to want to reuse
them again later.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we change load_hander() to use an ori instead of addi, we can load handlers
upto 64k away provided we are still 64k aligned.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes the large gap between 0x1800 and 0x3000.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove redundancy spaces and make tab usage consistent.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we build a kernel with CONFIG_RELOCATABLE=y CONFIG_CRASH_DUMP=n,
the kernel fails when we run at a non zero offset. It turns out
we were incorrectly wrapping some of the relocatable kernel code
with CONFIG_CRASH_DUMP.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A PVR of 0x0F000004 means we are arch v2.07 complicate ie, POWER8.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ibm,architecture.vec for POWER8 and allows us to support more
than one parition per core.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit ea96025a('Don't use alloc_bootmem() in init_IRQ() path')
changed alloc_bootmem() to kzalloc(),
but missed to change free_bootmem() to kfree().
So correct it.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On powerpc, ptrace will disable hardware breakpoint request once the
breakpoint is hit. It is the responsibility of the caller to set it
again. However, when the caller sets the hardware breakpoint again
using ptrace(PTRACE_SET_DEBUGREG, child_pid, 0, addr), the hardware
breakpoint is not enabled.
While gdb's approach is to unregister and re-register the hardware
breakpoint every time the breakpoint is hit - which is working fine,
this could affect other programs trying to re-register hardware
breakpoint without unregistering.
This patch enables hardware breakpoint if the caller is re-registering.
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only difference between powerpc and asm-generic le-bitops is
test_bit_le(). Usually all bitops require a long aligned bitmap.
But powerpc test_bit_le() can take an unaligned address.
There is no special callsite of test_bit_le() that needs unaligned
access in powerpc as far as I can see. So convert to use
asm-generic/bitops/le.h for powerpc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace BITOP_MASK and BITOP_WORD with BIT_MASK and BIT_WORD defined
in linux/bitops.h and remove BITOP_* which are not used anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Caluculate the bitmap size with BITS_TO_LONGS()
- Use bitmap_empty() to verify that all bits are cleared
This also includes a printk to pr_warn() conversion.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are many cases that Semiconductor is misspelled. The patch
fix these typos.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed a couple of function prototypes for functions that
no longer exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Most of setup.h should not be exported to userspace, so move it
back. All we are left with is the asm-generic include to pick
up the COMMAND_LINE_SIZE define.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix global symbol name to match actual denorm_exception_hv label.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Just a copy of POWER7 for now. Will update with new code later.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are going to reuse this in POWER8 so make the name generic.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we have two cache events that require different settings of the L2SEL
bits in MMCR1 then we can not schedule those events simultaneously. Add
logic to the constraint handling to express that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The transition time for the 7447A is around 8ms which makes it possible
to use the ondemand governor. This has been tested on the iBook G4
(PowerBook6,7).
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PPC_PTRACE_GETHWDBGINFO, PPC_PTRACE_SETHWDEBUG and PPC_PTRACE_DELHWDEBUG are
PowerPC specific ptrace flags that use the watchpoint register. While they are
targeted primarily towards BookE users, user-space applications such as GDB
have started using them for BookS too. This patch enables the use of generic
hardware breakpoint interfaces for these new flags.
Apart from the usual benefits of using generic hw-breakpoint interfaces, these
changes allow debuggers (such as GDB) to use a common set of ptrace flags for
their watchpoint needs and allow more precise breakpoint specification (length
of the variable can be specified).
Mikey added: rebased and added dbginfo.features around #ifdef
CONFIG_HAVE_HW_BREAKPOINT
Signed-off-by: K.Prasad <prasad@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The last user of ppc_md.idle_loop() was removed when we dropped the
legacy iSeries code, in commit 8ee3e0d.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL provides the firmware base/entry in registers at boot time
for debugging purposes. We had a bug in the code trying to stash
these into the appropriate kernel globals (a line of code was
probably dropped by accident back when this was merged)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function initialize_flash_pde_data is only called four times. All four
calls are in the function rtas_flash_init, and on the failure of any of the
calls, remove_flash_pde is called on the third argument of each of the
calls. There is thus no need for initialize_flash_pde_data to call
remove_flash_pde on the same argument. remove_flash_pde kfrees the data
field of its argument, and does not clear that field, so this amounts ot a
possible double free.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're couples of functions defined to print debugging messages
during initializing P7IOC. However, we got bogus output from those
functions like pe_info(). The problem here is that the message
level (the first parameter to printk()) isn't printable and that
caused the bogus output.
The patch fixes the issue by merging __pe_printk() to the macro
define_pe_printk_level() so that we can pass the message level
directly to printk().
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It is possible to configure a kernel which has xmon enabled, but has no
udbg backend to provide IO. This can make xmon rather confusing, as it
produces no output, blocks for two seconds, and then returns.
As a last resort we can instead try to printk(), which may deadlock or
otherwise crash, but tries quite hard not to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently xmon_depth_to_print is static and global, but it's only
ever used in xmon_show_stack().
At least with a modern compiler it's inlined, so there's no point
in it being static, we could #define it but it's only used in one
place.
By reworking the logic we can drop count and just decrement the
max value as a loop counter. Also switch to a while loop so we
actually print no more than 64 frames as you'd expect based on the
variable name.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use STACK_FRAME_OVERHEAD in the exception vectors to establish
the exception frame, so it should be good enough to use here.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Neither REGS_PER_LINE or LAST_VOLATILE are used, nor have they ever
been as far back as I can see.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two #defines that rename scanhex() and skipbl() to
xmon_scanhex() and xmon_skipbl() - but no one ever uses those
names.
So the only effect is to rename the actual symbols in the generated
code, and AFACIS there is no reason to do that, so drop them.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The routines in start.c are only ever called from nonstdio.c, so if we
move them in there they can become static which is nice.
I suspect the idea behind the separation was that start.c could be
replaced in order to build xmon in userland. If anyone still cares about
doing that we could handle that with an ifdef or two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xmon_getchar() is only called from within nonstdio.c, so make it static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This has been empty since 2005, commit 51d3082 "Unify udbg (#2)".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It looks like xmon_expect() was used for doing xmon over a modem (!?),
that code was dropped in 2005 in commit 51d3082 "Unify udbg (#2)".
Once xmon_expect() is gone xmon_read_poll() is unused, drop it too.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The last user of udbg_read() was removed in 2005, in commit fca5dcd
"Simplify and clean up the xmon terminal I/O".
Given we haven't needed it for 7 years we can probably drop it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the "Disintegrate asm/system.h for PowerPC"
(ae3a197e3d) This has been failing when
DEBUG is #defined.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't use 47x only #defines for TLBIVAX or ICBT, supply and use helpers
in ppc-opcode.h
This fixes a compile breakage.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anticipating growth in coming years, we should ensure we are getting a
good lead on testing.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the pSeries_reconfig.h header file. At this point there is only one
definition in the file, pSeries_coalesce_init(), which can be
moved to rtas.h.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rename the prom_*_property routines of the generic OF code to of_*_property.
This brings them in line with the naming used by the rest of the OF code.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch moves the notification chain for updates to the device tree
from the powerpc/pseries code to the base OF code. This makes this
functionality available to all architectures.
Additionally the notification chain is updated to allow notifications
for property add/remove/update. To make this work a pointer to a new
struct (of_prop_reconfig) is passed to the routines in the notification chain.
The of_prop_reconfig property contains a pointer to the node containing the
property and a pointer to the property itself. In the case of property
updates, the property pointer refers to the new property.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch moves the definition of the of_drconf_cell struct to asm/prom.h
to make it available for all powerpc/pseries code.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When adding or removing a device tree node we should also update
the device tree in /proc/device-tree. This action is already done in the
generic OF code for adding/removing properties of a node. This patch adds
this functionality for nodes.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In order to promote interoperability between userspace tracers and ftrace,
add a trace_clock that reports raw TSC values which will then be recorded
in the ring buffer. Userspace tracers that also record TSCs are then on
exactly the same time base as the kernel and events can be unambiguously
interlaced.
Tested: Enabled a tracepoint and the "tsc" trace_clock and saw very large
timestamp values.
v2:
Move arch-specific bits out of generic code.
v3:
Rename "x86-tsc", cleanups
v7:
Generic arch bits in Kbuild.
Google-Bug-Id: 6980623
Link: http://lkml.kernel.org/r/1352837903-32191-1-git-send-email-dhsharp@google.com
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Signed-off-by: David Sharp <dhsharp@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional changes.
powerpc is the only user of arch_uprobe_enable/disable_step() helpers,
but they should die. They can not be used correctly, every arch needs
its own implementation (like x86 does). And they do not really help
even as initial-and-almost-working code, arch_uprobe_*_xol() hooks can
easily use user_enable/disable_single_step() directly.
Change arch_uprobe_*_step() to do nothing, and convert powerpc to use
ptrace helpers. This is equally wrong, powerpc needs the arch-specific
fixes.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cleanup. No need to clear TIF_UPROBE, uprobe_notify_resume() does this.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new uapi framework splits kernel internal and user space exported
bits of header files more cleanly. Adjust the ePAPR header accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes an error in the inline asm in try_lock_hpte() where we
were erroneously using a register number as an immediate operand.
The bug only affects an error path, and in fact the code will still
work as long as the compiler chooses some register other than r0
for the "bits" variable. Nevertheless it should still be fixed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 55b665b026 ("KVM: PPC: Book3S HV: Provide a way for userspace
to get/set per-vCPU areas") includes a check on the length of the
dispatch trace log (DTL) to make sure the buffer is at least one entry
long. This is appropriate when registering a buffer, but the
interface also allows for any existing buffer to be unregistered by
specifying a zero address. In this case the length check is not
appropriate. This makes the check conditional on the address being
non-zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the code that accounts stolen time tends to overestimate the
stolen time, and will sometimes report more stolen time in a DTL
(dispatch trace log) entry than has elapsed since the last DTL entry.
This can cause guests to underflow the user or system time measured
for some tasks, leading to ridiculous CPU percentages and total runtimes
being reported by top and other utilities.
In addition, the current code was designed for the previous policy where
a vcore would only run when all the vcpus in it were runnable, and so
only counted stolen time on a per-vcore basis. Now that a vcore can
run while some of the vcpus in it are doing other things in the kernel
(e.g. handling a page fault), we need to count the time when a vcpu task
is preempted while it is not running as part of a vcore as stolen also.
To do this, we bring back the BUSY_IN_HOST vcpu state and extend the
vcpu_load/put functions to count preemption time while the vcpu is
in that state. Handling the transitions between the RUNNING and
BUSY_IN_HOST states requires checking and updating two variables
(accumulated time stolen and time last preempted), so we add a new
spinlock, vcpu->arch.tbacct_lock. This protects both the per-vcpu
stolen/preempt-time variables, and the per-vcore variables while this
vcpu is running the vcore.
Finally, we now don't count time spent in userspace as stolen time.
The task could be executing in userspace on behalf of the vcpu, or
it could be preempted, or the vcpu could be genuinely stopped. Since
we have no way of dividing up the time between these cases, we don't
count any of it as stolen.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the Book3S HV code implements a policy on multi-threaded
processors (i.e. POWER7) that requires all of the active vcpus in a
virtual core to be ready to run before we run the virtual core.
However, that causes problems on reset, because reset stops all vcpus
except vcpu 0, and can also reduce throughput since all four threads
in a virtual core have to wait whenever any one of them hits a
hypervisor page fault.
This relaxes the policy, allowing the virtual core to run as soon as
any vcpu in it is runnable. With this, the KVMPPC_VCPU_STOPPED state
and the KVMPPC_VCPU_BUSY_IN_HOST state have been combined into a single
KVMPPC_VCPU_NOTREADY state, since we no longer need to distinguish
between them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a thread in a virtual core becomes runnable while other threads
in the same virtual core are already running in the guest, it is
possible for the latecomer to join the others on the core without
first pulling them all out of the guest. Currently this only happens
rarely, when a vcpu is first started. This fixes some bugs and
omissions in the code in this case.
First, we need to check for VPA updates for the latecomer and make
a DTL entry for it. Secondly, if it comes along while the master
vcpu is doing a VPA update, we don't need to do anything since the
master will pick it up in kvmppc_run_core. To handle this correctly
we introduce a new vcore state, VCORE_STARTING. Thirdly, there is
a race because we currently clear the hardware thread's hwthread_req
before waiting to see it get to nap. A latecomer thread could have
its hwthread_req cleared before it gets to test it, and therefore
never increment the nap_count, leading to messages about wait_for_nap
timeouts.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There were a few places where we were traversing the list of runnable
threads in a virtual core, i.e. vc->runnable_threads, without holding
the vcore spinlock. This extends the places where we hold the vcore
spinlock to cover everywhere that we traverse that list.
Since we possibly need to sleep inside kvmppc_book3s_hv_page_fault,
this moves the call of it from kvmppc_handle_exit out to
kvmppc_vcpu_run, where we don't hold the vcore lock.
In kvmppc_vcore_blocked, we don't actually need to check whether
all vcpus are ceded and don't have any pending exceptions, since the
caller has already done that. The caller (kvmppc_run_vcpu) wasn't
actually checking for pending exceptions, so we add that.
The change of if to while in kvmppc_run_vcpu is to make sure that we
never call kvmppc_remove_runnable() when the vcore state is RUNNING or
EXITING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Subsequent patches implementing in-kernel XICS emulation will make it
possible for IPIs to arrive at secondary threads at arbitrary times.
This fixes some races in how we start the secondary threads, which
if not fixed could lead to occasional crashes of the host kernel.
This makes sure that (a) we have grabbed all the secondary threads,
and verified that they are no longer in the kernel, before we start
any thread, (b) that the secondary thread loads its vcpu pointer
after clearing the IPI that woke it up (so we don't miss a wakeup),
and (c) that the secondary thread clears its vcpu pointer before
incrementing the nap count. It also removes unnecessary setting
of the vcpu and vcore pointers in the paca in kvmppc_core_vcpu_load.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a Book3S HV KVM guest is running, we need the host to be in
single-thread mode, that is, all of the cores (or at least all of
the cores where the KVM guest could run) to be running only one
active hardware thread. This is because of the hardware restriction
in POWER processors that all of the hardware threads in the core
must be in the same logical partition. Complying with this restriction
is much easier if, from the host kernel's point of view, only one
hardware thread is active.
This adds two hooks in the SMP hotplug code to allow the KVM code to
make sure that secondary threads (i.e. hardware threads other than
thread 0) cannot come online while any KVM guest exists. The KVM
code still has to check that any core where it runs a guest has the
secondary threads offline, but having done that check it can now be
sure that they will not come online while the guest is running.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The new uapi framework splits kernel internal and user space exported
bits of header files more cleanly. Adjust the ePAPR header accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
The mtspr/mfspr emulation code became quite big over time. Move it
into its own function so things stay more readable.
Signed-off-by: Alexander Graf <agraf@suse.de>
When remembering the direction of a DCR transaction, we should write
to the same variable that we interpret on later when doing vcpu_run
again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Cc: stable@vger.kernel.org
This patch filters noslot pfn out from error pfns based on Marcelo comment:
noslot pfn is not a error pfn
After this patch,
- is_noslot_pfn indicates that the gfn is not in slot
- is_error_pfn indicates that the gfn is in slot but the error is occurred
when translate the gfn to pfn
- is_error_noslot_pfn indicates that the pfn either it is error pfns or it
is noslot pfn
And is_invalid_pfn can be removed, it makes the code more clean
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
arch/powerpc/include/asm/Kbuild
arch/powerpc/include/asm/kvm_para.h
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
vtime_account_system() currently has only one caller with
vtime_account() which is irq safe.
Now we are going to call it from other places like kvm where
irqs are not always disabled by the time we account the cputime.
So let's make it irqsafe. The arch implementation part is now
prefixed with "__".
vtime_account_idle() arch implementation is prefixed accordingly
to stay consistent.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Currently, when booting MPC52xx based platforms, we get:
mpc52xx_irqhost_map: invalid irq: virq=16, l1=0, l2=3
irq: irq-16==>hwirq-0x3 mapping failed: -22
[WARNing skipped]
The warning is wrong since the mapping itself is valid. However, there is no
support for that type of IRQ currently. Print a proper warning and bind the irq
to a no_irq chip.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: John Bonesio <bones@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add a node for the pcm030-audio-fabric ASoC driver
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch defines new ioctl codes TIOCGPKT, TIOCGPTLCK,
TIOCGEXCL for fetching pty's packet mode and locking state,
and exclusive mode of tty.
[ No real handlers for the codes though, this will be
addressed in another patch for easier review and
bisectability ]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmu_notifier_retry is not specific to any vcpu (and never will be)
so only take struct kvm as a parameter.
The motivation is the ARM mmu code that needs to call this from
somewhere where we long let go of the vcpu pointer.
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Earlier without cpuidle framework on pseries, the native arch
idle routine comprised of both snooze and nap
states. smt_snooze_delay variable was used to delay
the idle process entry to deeper idle state like nap.
With the coming of cpuidle, this arch specific idle was replaced
by two different idle routines, one for supporting snooze and other
for nap. This enabled addition of more
low level idle states on pseries in the future.
On adopting the generic cpuidle framework for POWER systems,
the decision of which idle state to choose from, given a predicted
idle time is taken by the menu governor based on
target_residency and exit_latency of the idle states.
target_residency is the minimum time to be resident in that idle state.
Exit_latency is time taken to exit out of idle state.
Deeper the idle state, both the target residency and exit latency
would be higher.
In the current design, smt_snooze_delay is used as target_residency
for the snooze state which is incorrect, as it is not the
minimum but the maximum duration to be in snooze state.
This would result in the governor in taking bad decision,
as presently target_residency of nap < target_residency of snooze
inspite of nap being deeper idle state.
This patch aims to fix this problem by replacing the smt_snooze_delay loop
in snooze state, with the need_resched() as the governor is aware of
entry and exit of various idle transitions based on which
next idle time prediction.
The governor is intelligent enough to determine the idle state the needs to
be transitioned to and maintains a whole of heuristics including
io load, previous idle states predictions etc for the same, based on
which idle state entry decision is taken.
With this fix, of setting target_residency of snooze to 0
nap to smt_snooze_delay
if the predicted idle time is less
than smt_snooze_delay (target_residency of nap)
value governor would pick snooze state, else nap. This adhers to the
previous native idle design.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
smt_snooze_delay was designed to delay idle loop's nap entry
in the native idle code before it got ported over to use as part of
the cpuidle framework.
A -ve value assigned to smt_snooze_delay should result in
busy looping, in other words disabling the entry to nap state.
- https://lists.ozlabs.org/pipermail/linuxppc-dev/2010-May/082450.html
This particular functionality can be achieved currently by
echo 1 > /sys/devices/system/cpu/cpu*/state1/disable
but it is broken when one assigns -ve value to the smt_snooze_delay
variable either via sysfs entry or ppc64_cpu util.
This patch aims to fix this, by disabling nap state when smt_snooze_delay
variable is set to -ve value.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the redundant target residency initialisation in pseries_cpuidle_driver_init().
This is currently over-writing the residency time updated as part of the static
table, resulting in all the idle states having the same target
residency of 100us which is incorrect. This may result in the menu governor making
wrong state decisions.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix build failure for powerpc KVM by adding missing VPN_SHIFT definition
and the ';'
arch/powerpc/kvm/book3s_32_mmu_host.c: In function 'kvmppc_mmu_map_page':
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: 'VPN_SHIFT' undeclared (first use in this function)
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: (Each undeclared identifier is reported only once
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: for each function it appears in.)
arch/powerpc/kvm/book3s_32_mmu_host.c:178: error: expected ';' before 'next_pteg'
arch/powerpc/kvm/book3s_32_mmu_host.c:190: error: label 'next_pteg' used but not defined
make[1]: *** [arch/powerpc/kvm/book3s_32_mmu_host.o] Error 1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kernel_thread() callbacks are *not* in modules and are not going to
be there. And it's not even read in ppc32 ret_from_kernel_thread(),
so no need to bother with it there either.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull powerpc uapi disintegration from Benjamin Herrenschmidt.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
UAPI: (Scripted) Disintegrate arch/powerpc/include/asm
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
Merge misc fixes from Andrew Morton:
"Followups, fixes and some random stuff I found on the internet."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (11 patches)
perf: fix duplicate header inclusion
memcg, kmem: fix build error when CONFIG_INET is disabled
rtc: kconfig: fix RTC_INTF defaults connected to RTC_CLASS
rapidio: fix comment
lib/kasprintf.c: use kmalloc_track_caller() to get accurate traces for kvasprintf
rapidio: update for destination ID allocation
rapidio: update asynchronous discovery initialization
rapidio: use msleep in discovery wait
mm: compaction: fix bit ranges in {get,clear,set}_pageblock_skip()
arch/powerpc/platforms/pseries/hotplug-memory.c: section removal cleanups
arch/powerpc/platforms/pseries/hotplug-memory.c: fix section handling code
Followups to d760afd4d2 ("memory-hotplug: suppress "Trying to free
nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning").
- use unsigned long type, as overflows are conceivable
- rename `i' to the less-misleading and more informative `section'
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Merge patches from Andrew Morton:
"A few misc things and very nearly all of the MM tree. A tremendous
amount of stuff (again), including a significant rbtree library
rework."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (160 commits)
sparc64: Support transparent huge pages.
mm: thp: Use more portable PMD clearing sequenece in zap_huge_pmd().
mm: Add and use update_mmu_cache_pmd() in transparent huge page code.
sparc64: Document PGD and PMD layout.
sparc64: Eliminate PTE table memory wastage.
sparc64: Halve the size of PTE tables
sparc64: Only support 4MB huge pages and 8KB base pages.
memory-hotplug: suppress "Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning
mm: memcg: clean up mm_match_cgroup() signature
mm: document PageHuge somewhat
mm: use %pK for /proc/vmallocinfo
mm, thp: fix mlock statistics
mm, thp: fix mapped pages avoiding unevictable list on mlock
memory-hotplug: update memory block's state and notify userspace
memory-hotplug: preparation to notify memory block's state at memory hot remove
mm: avoid section mismatch warning for memblock_type_name
make GFP_NOTRACK definition unconditional
cma: decrease cc.nr_migratepages after reclaiming pagelist
CMA: migrate mlocked pages
kpageflags: fix wrong KPF_THP on non-huge compound pages
...
When our x86 box calls __remove_pages(), release_mem_region() shows many
warnings. And x86 box cannot unregister iomem_resource.
"Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>"
release_mem_region() has been changed to be called in each
PAGES_PER_SECTION by commit de7f0cba96 ("memory hotplug: release
memory regions in PAGES_PER_SECTION chunks"). Because powerpc registers
iomem_resource in each PAGES_PER_SECTION chunk. But when I hot add
memory on x86 box, iomem_resource is register in each _CRS not
PAGES_PER_SECTION chunk. So x86 box unregisters iomem_resource.
The patch fixes the problem.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x86 implementation of atomic_dec_if_positive is quite generic, so make
it available to all architectures.
This is needed for "swap: add a simple detector for inappropriate swapin
readahead".
[akpm@linux-foundation.org: do the "#define foo foo" trick in the conventional manner]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core page allocator ensures that page flags are zeroed when freeing
pages via free_pages_check. A number of architectures (ARM, PPC, MIPS)
rely on this property to treat new pages as dirty with respect to the data
cache and perform the appropriate flushing before mapping the pages into
userspace.
This can lead to cache synchronisation problems when using hugepages,
since the allocator keeps its own pool of pages above the usual page
allocator and does not reset the page flags when freeing a page into the
pool.
This patch adds a new architecture hook, arch_clear_hugepage_flags, so
that architectures which rely on the page flags being in a particular
state for fresh allocations can adjust the flags accordingly when a page
is freed into the pool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some security modules and oprofile still uses VM_EXECUTABLE for retrieving
a task's executable file. After this patch they will use mm->exe_file
directly. mm->exe_file is protected with mm->mmap_sem, so locking stays
the same.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [arch/tile]
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> [tomoyo]
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce SYSCTL_EXCEPTION_TRACE config option and selec it in the
architectures requiring support for the "exception-trace" debug_table
entry in kernel/sysctl.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_DEBUG_KMEMLEAK config option and select it in corresponding
architecture Kconfig files. DEBUG_KMEMLEAK now only depends on
HAVE_DEBUG_KMEMLEAK.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
other branch as normal asm-generic changes do. One is a fix for a
build warning, the other two are more interesting:
* A patch from Mark Brown to allow using the common clock infrastructure
on all architectures, so we can use the clock API in architecture
independent device drivers.
* The UAPI split patches from David Howells for the asm-generic files.
There are other architecture specific series that are going through
the arch maintainer tree and that depend on this one.
There may be a few small merge conflicts between Mark's patch and
the following arch header file split patches. In each case the solution
will be to keep the new "generic-y += clkdev.h" line, even if it
ends up being the only line in the Kbuild file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Aaki
-----END PGP SIGNATURE-----
Merge tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"This has three changes for asm-generic that did not really fit into
any other branch as normal asm-generic changes do. One is a fix for a
build warning, the other two are more interesting:
* A patch from Mark Brown to allow using the common clock
infrastructure on all architectures, so we can use the clock API in
architecture independent device drivers.
* The UAPI split patches from David Howells for the asm-generic
files. There are other architecture specific series that are going
through the arch maintainer tree and that depend on this one.
There may be a few small merge conflicts between Mark's patch and the
following arch header file split patches. In each case the solution
will be to keep the new "generic-y += clkdev.h" line, even if it ends
up being the only line in the Kbuild file."
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
UAPI: (Scripted) Disintegrate include/asm-generic
asm-generic: Add default clkdev.h
asm-generic: xor: mark static functions as __maybe_unused
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A new label is also added to avoid freeing things that are known to not yet
be allocated.
A simplified version of the semantic match that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alexander Graf <agraf@suse.de>
The PAPR paravirtualization interface lets guests register three
different types of per-vCPU buffer areas in its memory for communication
with the hypervisor. These are called virtual processor areas (VPAs).
Currently the hypercalls to register and unregister VPAs are handled
by KVM in the kernel, and userspace has no way to know about or save
and restore these registrations across a migration.
This adds "register" codes for these three areas that userspace can
use with the KVM_GET/SET_ONE_REG ioctls to see what addresses have
been registered, and to register or unregister them. This will be
needed for guest hibernation and migration, and is also needed so
that userspace can unregister them on reset (otherwise we corrupt
guest memory after reboot by writing to the VPAs registered by the
previous kernel).
The "register" for the VPA is a 64-bit value containing the address,
since the length of the VPA is fixed. The "registers" for the SLB
shadow buffer and dispatch trace log (DTL) are 128 bits long,
consisting of the guest physical address in the high (first) 64 bits
and the length in the low 64 bits.
This also fixes a bug where we were calling init_vpa unconditionally,
leading to an oops when unregistering the VPA.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set all the guest floating-point
state using the KVM_[GS]ET_ONE_REG ioctls. The floating-point state
includes all of the traditional floating-point registers and the
FPSCR (floating point status/control register), all the VMX/Altivec
vector registers and the VSCR (vector status/control register), and
on POWER7, the vector-scalar registers (note that each FP register
is the high-order half of the corresponding VSR).
Most of these are implemented in common Book 3S code, except for VSX
on POWER7. Because HV and PR differ in how they store the FP and VSX
registers on POWER7, the code for these cases is not common. On POWER7,
the FP registers are the upper halves of the VSX registers vsr0 - vsr31.
PR KVM stores vsr0 - vsr31 in two halves, with the upper halves in the
arch.fpr[] array and the lower halves in the arch.vsr[] array, whereas
HV KVM on POWER7 stores the whole VSX register in arch.vsr[].
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix whitespace, vsx compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set various SPRs (special-purpose
registers) using the KVM_[GS]ET_ONE_REG ioctls. With this, userspace
can get and set all the SPRs that are part of the guest state, either
through the KVM_[GS]ET_REGS ioctls, the KVM_[GS]ET_SREGS ioctls, or
the KVM_[GS]ET_ONE_REG ioctls.
The SPRs that are added here are:
- DABR: Data address breakpoint register
- DSCR: Data stream control register
- PURR: Processor utilization of resources register
- SPURR: Scaled PURR
- DAR: Data address register
- DSISR: Data storage interrupt status register
- AMR: Authority mask register
- UAMOR: User authority mask override register
- MMCR0, MMCR1, MMCRA: Performance monitor unit control registers
- PMC1..PMC8: Performance monitor unit counter registers
In order to reduce code duplication between PR and HV KVM code, this
moves the kvm_vcpu_ioctl_[gs]et_one_reg functions into book3s.c and
centralizes the copying between user and kernel space there. The
registers that are handled differently between PR and HV, and those
that exist only in one flavor, are handled in kvmppc_[gs]et_one_reg()
functions that are specific to each flavor.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: minimal style fixes]
Signed-off-by: Alexander Graf <agraf@suse.de>
Avoid a race as described in the code comment.
Also remove a related smp_wmb() from booke's kvmppc_prepare_to_enter().
I can't see any reason for it, and the book3s_pr version doesn't have it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
We were only allocating half the bytes we need, which was made more
obvious by a recent fix to the memset in clear_tlb1_bitmap().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Cc: stable@vger.kernel.org
In the case where the host kernel is using a 64kB base page size and
the guest uses a 4k HPTE (hashed page table entry) to map an emulated
MMIO device, we were calculating the guest physical address wrongly.
We were calculating a gfn as the guest physical address shifted right
16 bits (PAGE_SHIFT) but then only adding back in 12 bits from the
effective address, since the HPTE had a 4k page size. Thus the gpa
reported to userspace was missing 4 bits.
Instead, we now compute the guest physical address from the HPTE
without reference to the host page size, and then compute the gfn
by shifting the gpa right PAGE_SHIFT bits.
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When making a vcpu non-runnable we incorrectly changed the
thread IDs of all other threads on the core, just remove that
code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes the powerpc "generic" updates of vcpu->cpu in load and
put, and moves them to the various backends.
The reason is that "HV" KVM does its own sauce with that field
and the generic updates might corrupt it. The field contains the
CPU# of the -first- HW CPU of the core always for all the VCPU
threads of a core (the one that's online from a host Linux
perspective).
However, the preempt notifiers are going to be called on the
threads VCPUs when they are running (due to them sleeping on our
private waitqueue) causing unload to be called, potentially
clobbering the value.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds an implementation of kvm_arch_flush_shadow_memslot for
Book3S HV, and arranges for kvmppc_core_commit_memory_region to
flush the dirty log when modifying an existing slot. With this,
we can handle deletion and modification of memory slots.
kvm_arch_flush_shadow_memslot calls kvmppc_core_flush_memslot, which
on Book3S HV now traverses the reverse map chains to remove any HPT
(hashed page table) entries referring to pages in the memslot. This
gets called by generic code whenever deleting a memslot or changing
the guest physical address for a memslot.
We flush the dirty log in kvmppc_core_commit_memory_region for
consistency with what x86 does. We only need to flush when an
existing memslot is being modified, because for a new memslot the
rmap array (which stores the dirty bits) is all zero, meaning that
every page is considered clean already, and when deleting a memslot
we obviously don't care about the dirty bits any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have an architecture-specific field in the kvm_memory_slot
structure, we can use it to store the array of page physical addresses
that we need for Book3S HV KVM on PPC970 processors. This reduces the
size of struct kvm_arch for Book3S HV, and also reduces the size of
struct kvm_arch_memory_slot for other PPC KVM variants since the fields
in it are now only compiled in for Book3S HV.
This necessitates making the kvm_arch_create_memslot and
kvm_arch_free_memslot operations specific to each PPC KVM variant.
That in turn means that we now don't allocate the rmap arrays on
Book3S PR and Book E.
Since we now unpin pages and free the slot_phys array in
kvmppc_core_free_memslot, we no longer need to do it in
kvmppc_core_destroy_vm, since the generic code takes care to free
all the memslots when destroying a VM.
We now need the new memslot to be passed in to
kvmppc_core_prepare_memory_region, since we need to initialize its
arch.slot_phys member on Book3S HV.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The generic KVM code uses SRCU (sleeping RCU) to protect accesses
to the memslots data structures against updates due to userspace
adding, modifying or removing memory slots. We need to do that too,
both to avoid accessing stale copies of the memslots and to avoid
lockdep warnings. This therefore adds srcu_read_lock/unlock pairs
around code that accesses and uses memslots.
Since the real-mode handlers for H_ENTER, H_REMOVE and H_BULK_REMOVE
need to access the memslots, and we don't want to call the SRCU code
in real mode (since we have no assurance that it would only access
the linear mapping), we hold the SRCU read lock for the VM while
in the guest. This does mean that adding or removing memory slots
while some vcpus are executing in the guest will block for up to
two jiffies. This tradeoff is acceptable since adding/removing
memory slots only happens rarely, while H_ENTER/H_REMOVE/H_BULK_REMOVE
are performance-critical hot paths.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current form of DO_KVM macro restricts its use to one call per input
parameter set. This is caused by kvmppc_resume_\intno\()_\srr1 symbol
definition.
Duplicate calls of DO_KVM are required by distinct implementations of
exeption handlers which are delegated at runtime. Use a rare label number
to avoid conflicts with the calling contexts.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on HV aware hosts, we can not trap when the guest sets the FP
bit, so we just let it do so when it wants to, because it has full access to
MSR.
For non-HV aware hosts with an FPU (like 440), we need to also adjust the
shadow MSR though. Otherwise the guest gets an FP unavailable trap even when
it really enabled the FP bit in MSR.
Signed-off-by: Alexander Graf <agraf@suse.de>
Since we always mark pages as dirty immediately when mapping them read/write
now, there's no need for the dirty flag in our cache.
Signed-off-by: Alexander Graf <agraf@suse.de>
Exit traces are a lot easier to read when you don't have to remember
cryptic numbers for guest exit reasons. Symbolify them in our trace
output.
Signed-off-by: Alexander Graf <agraf@suse.de>
We need to make sure that vcpu->arch.pvr is initialized to a sane value,
so let's just take the host PVR.
Signed-off-by: Alexander Graf <agraf@suse.de>
IAC/DAC are defined as 32 bit while they are 64 bit wide. So ONE_REG
interface is added to set/get them.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the watchdog emulation in KVM. The watchdog
emulation is enabled by KVM_ENABLE_CAP(KVM_CAP_PPC_BOOKE_WATCHDOG) ioctl.
The kernel timer are used for watchdog emulation and emulates
h/w watchdog state machine. On watchdog timer expiry, it exit to QEMU
if TCR.WRC is non ZERO. QEMU can reset/shutdown etc depending upon how
it is configured.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[bharat.bhushan@freescale.com: reworked patch]
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
[agraf: adjust to new request framework]
Signed-off-by: Alexander Graf <agraf@suse.de>
Requests may want to tell us that we need to go back into host state,
so add a return value for the checks.
Signed-off-by: Alexander Graf <agraf@suse.de>
Our prepare_to_enter helper wants to be able to return in more circumstances
to the host than only when an interrupt is pending. Broaden the interface a
bit and move even more generic code to the generic helper.
Signed-off-by: Alexander Graf <agraf@suse.de>
We don't need to do anything when mode is EXITING_GUEST_MODE, because
we essentially are outside of guest mode and did everything it asked
us to do by the time we check it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Today, we disable preemption while inside guest context, because we need
to expose to the world that we are not in a preemptible context. However,
during that time we already have interrupts disabled, which would indicate
that we are in a non-preemptible context.
The reason the checks for irqs_disabled() fail for us though is that we
manually control hard IRQs and ignore all the lazy EE framework. Let's
stop doing that. Instead, let's always use lazy EE to indicate when we
want to disable IRQs, but do a special final switch that gets us into
EE disabled, but soft enabled state. That way when we get back out of
guest state, we are immediately ready to process interrupts.
This simplifies the code drastically and reduces the time that we appear
as preempt disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
When getting out of __vcpu_run, let's be consistent about the state we
return in. We want to always
* have IRQs enabled
* have called kvm_guest_exit before
Signed-off-by: Alexander Graf <agraf@suse.de>
When going out of guest mode, indicate that we are in vcpu->mode. That way
requests from other CPUs don't needlessly need to kick us to process them,
because it'll just happen next time we enter the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we use our generic exit helper, we can safely drop our previous
kvm_resched that we used to trigger at the beginning of the exit handler
function.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have very simple MMU Notifier support for e500 in place,
also add the same simple support to book3s. It gets us one step closer
to actual fast support.
Signed-off-by: Alexander Graf <agraf@suse.de>
We need to do the same things when preparing to enter a guest for booke and
book3s_pr cores. Fold the generic code into a generic function that both call.
Signed-off-by: Alexander Graf <agraf@suse.de>
We only call kvmppc_check_requests() when vcpu->requests != 0, so drop
the redundant check in the function itself
Signed-off-by: Alexander Graf <agraf@suse.de>
Without trace points, debugging what exactly is going on inside guest
code can be very tricky. Add a few more trace points at places that
hopefully tell us more when things go wrong.
Signed-off-by: Alexander Graf <agraf@suse.de>
The e500 target has lived without mmu notifiers ever since it got
introduced, but fails for the user space check on them with hugetlbfs.
So in order to get that one working, implement mmu notifiers in a
reasonably dumb fashion and be happy. On embedded hardware, we almost
never end up with mmu notifier calls, since most people don't overcommit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Generic KVM code might want to know whether we are inside guest context
or outside. It also wants to be able to push us out of guest context.
Add support to the BookE code for the generic vcpu->mode field that describes
the above states.
Signed-off-by: Alexander Graf <agraf@suse.de>
We need a central place to check for pending requests in. Add one that
only does the timer check we already do in a different place.
Later, this central function can be extended by more checks.
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes breakage introduced by the following commit:
commit 6d2d82627f4f1e96a33664ace494fa363e0495cb
Author: Liu Yu-B13201 <Yu.Liu@freescale.com>
Date: Tue Jul 3 05:48:56 2012 +0000
PPC: Don't use hardcoded opcode for ePAPR hcall invocation
when a driver that uses ePAPR hypercalls is built as a module.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is printed once for every RMA or HPT region that get
preallocated. If one preallocates hundreds of such regions
(in order to run hundreds of KVM guests), that gets rather
painful, so make it a bit quieter.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
