Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we hit this error path we end up returning ERR_PTR(0) which is NULL.
The caller is not expecting that so it results in a NULL dereference.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm reviewing static checker warnings where we do ERR_PTR(0), which is
the same as NULL. I'm pretty sure we intended to return ERR_PTR(-EINVAL)
here. Sometimes these bugs lead to a NULL dereference but I don't
immediately see that problem here.
Fixes: 71d0ed7079 ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 83ada39bb79d ("net: factor out a helper to decrement the
skb refcount") provided and used a helper for decrementing skb usage,
but I missed at least a spot for it.
This change remove some more duplicated code reusing skb_unref() in
napi_consume_skb(), too. The helper uses an additional, unneeded
unlikely(!skb) test - napi_consume_skb() already check it a few lines
above - but the compiler is smart enough to optimize the duplicated
test out.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-06-14
Here's another batch of Bluetooth patches for the 4.13 kernel:
- Fix for Broadcom controllers not supporting Event Mask Page 2
- New QCA ROME USB ID for btusb
- Fix for Security Manager Protocol to use constant-time memcmp
- Improved support for TI WiLink chips
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The p_l2_info->pp_qid_usage[] array has "p_l2_info->queues" elements so
the > here should be a >= or we write beyond the end of the array.
Fixes: bbe3f233ec ("qed: Assign a unique per-queue index to queue-cid")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Add support for cable info access
Add support for cable info access via ethtool. This is done by accessing
the SFP+/QSFP internal EEPROM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for access cable info via ethtool.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCIA register is used to access the SFP+ and QSFP connector's
EPROM. It will be used to query the cable info.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ->ndo_change_mtu() callback comment to remove text
about returning error in case of undefined callback. This
change makes the comment match the existing code behavior.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney says:
====================
bpf: Changes needed (or desired) for MIPS support
This is a grab bag of changes to the bpf testing infrastructure I
developed working on MIPS eBPF JIT support. The change to
bpf_jit_disasm is probably universally beneficial, the others are more
MIPS specific.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems:
1) In MIPS the __NR_* macros expand to an expression, this causes the
sections of the object file to be named like:
.
.
.
[ 5] kprobe/(5000 + 1) PROGBITS 0000000000000000 000160 ...
[ 6] kprobe/(5000 + 0) PROGBITS 0000000000000000 000258 ...
[ 7] kprobe/(5000 + 9) PROGBITS 0000000000000000 000348 ...
.
.
.
The fix here is to use the "asm_offsets" trick to evaluate the macros
in the C compiler and generate a header file with a usable form of the
macros.
2) MIPS syscall numbers start at 5000, so we need a bigger map to hold
the sub-programs.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPS, conditional branches can only span 32k instructions. To
exceed this limit in the JIT with the BPF maximum of 4k insns, we need
to choose eBPF insns that expand to more than 8 machine instructions.
Use BPF_LD_ABS as it is quite complex. This forces the JIT to invert
the sense of the branch to branch around a long jump to the end.
This (somewhat) verifies that the branch inversion logic and target
address calculation of the long jumps are done correctly.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically allocate memory so that JIT images larger than the size of
the statically allocated array can be handled.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song says:
====================
bpf: permit bpf program narrower loads for ctx fields
Today, if users try to access a ctx field through a narrower load, e.g.,
__be16 prot = __sk_buff->protocol, verifier will fail.
This set contains the verifier change to permit such loads for
certain ctx fields as well as the new test cases in selftests/bpf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases in test_verifier and test_progs.
Negative tests are added in test_verifier as well.
The test in test_progs will compare the value of narrower ctx field
load result vs. the masked value of normal full-field load result,
and will fail if they are not the same.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, verifier will reject a program if it contains an
narrower load from the bpf context structure. For example,
__u8 h = __sk_buff->hash, or
__u16 p = __sk_buff->protocol
__u32 sample_period = bpf_perf_event_data->sample_period
which are narrower loads of 4-byte or 8-byte field.
This patch solves the issue by:
. Introduce a new parameter ctx_field_size to carry the
field size of narrower load from prog type
specific *__is_valid_access validator back to verifier.
. The non-zero ctx_field_size for a memory access indicates
(1). underlying prog type specific convert_ctx_accesses
supporting non-whole-field access
(2). the current insn is a narrower or whole field access.
. In verifier, for such loads where load memory size is
less than ctx_field_size, verifier transforms it
to a full field load followed by proper masking.
. Currently, __sk_buff and bpf_perf_event_data->sample_period
are supporting narrowing loads.
. Narrower stores are still not allowed as typical ctx stores
are just normal stores.
Because of this change, some tests in verifier will fail and
these tests are removed. As a bonus, rename some out of bound
__sk_buff->cb access to proper field name and remove two
redundant "skb cb oob" tests.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laura reported a sleep-in-atomic kernel warning inside
tcf_act_police_init() which calls gen_replace_estimator() with
spinlock protection.
It is not necessary in this case, we already have RTNL lock here
so it is enough to protect concurrent writers. For the reader,
i.e. tcf_act_police(), it needs to make decision based on this
rate estimator, in the worst case we drop more/less packets than
necessary while changing the rate in parallel, it is still acceptable.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Nick Huber <nicholashuber@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan dev should propagate the return value of mac address change for
lower device in the passthru mode, instead of always return 0.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-06-13
This series contains updates to ixgbe and ixgbevf only.
Jake completes his fix ups for our drivers with the ixgbe changes to
resolve a race condition in processing timestamp requests. These fixes
are the same fixes Jake applied earlier to the other drivers, including
the added statistic to help administrators know when an application
timestamp request is ignored.
With all the recent ixgbe/ixgbevf changes and fixes, Tony bumps the
the driver versions. Then Tony provides a fix to resolve a static
analysis warning by changing a variable to unsigned integer since the
value can never be negative.
Emil fixes an issue for X550 devices where the qde parameter was being
ignored, so PFQDE.HIDE_VLAN was not being set.
Jeff Mahoney from SuSE fixes a possible kernel crash, where there was
a small window where tasks writing to the sriov_numvfs sysfs attribute
can sneak in after we call register_netdev(). So we need to call
pci_set_drvdata() before and not after register_netdev() to preserve the
intent of commit 0fb6a55cc3 ("ixgbe: fix crash on rmmod after probe
fail").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We call pci_set_drvdata immediately after calling register_netdev,
which leaves a window where tasks writing to the sriov_numvfs sysfs
attribute can sneak in and crash the kernel. register_netdev cleans
up after itself so placing pci_set_drvdata immediately before it
should preserve the intent of commit 0fb6a55cc3 ("ixgbe: fix crash
on rmmod after probe fail").
Fixes: 0fb6a55cc3 ("ixgbe: fix crash on rmmod after probe fail")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck warns that the format string is incorrect in the function
ixgbe_get_strings(). Since the value cannot be negative, change the
variable to unsigned which matches the format specifier.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_write_qde() was ignoring the qde parameter which resulted
in PFQDE.HIDE_VLAN not being set for X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbevf version number.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe version number.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an ixgbe_ptp_tx_hang() function similar to the already existing
ixgbe_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver uses a state bit lock to avoid handling more than one Tx
timestamp request at once. This is required because hardware is limited
to a single set of registers for Tx timestamps.
The state bit lock is not properly cleaned up during
ixgbe_xmit_frame_ring() if the transmit fails such as due to DMA or TSO
failure. In some hardware this results in blocking timestamps until the
service task times out. In other hardware this results in a permanent
lock of the timestamp bit because we never receive an interrupt
indicating the timestamp occurred, since indeed the packet was never
transmitted.
Fix this by checking for DMA and TSO errors in ixgbe_xmit_frame_ring() and
properly cleaning up after ourselves when these occur.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the ixgbe driver is limited to handling a single Tx
timestamp request at a time. Thus, the driver ignores requests for Tx
timestamp while waiting for the current request to finish. It uses
a state bit lock which enforces that only one timestamp request is
honored at a time.
Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying applications
of a new Tx timestamp. Even a well behaved application sending only one
packet at a time and waiting for a response can wake up and send a new
packet before the bit lock is cleared. This results in needlessly
dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Florian Fainelli says:
====================
net: dsa: Multi-CPU ground work (v4)
This patch series prepares the ground for adding mutliple CPU port support to
DSA, and starts by removing redundant pieces of information such as
master_netdev which is cpu_dp->ethernet. Finally drivers are moved away from
directly accessing ds->dst->cpu_dp and use appropriate helper functions.
Note that if you have Device Tree blobs/platform configurations that are
currently listing multiple CPU ports, the proposed behavior in
dsa_ds_get_cpu_dp() will be to return the last bit set in ds->cpu_port_mask.
Future plans include:
- making dst->cpu_dp a flexible data structure (array, list, you name it)
- having the ability for drivers to return a default/preferred CPU port (if
necessary)
Changes in v4:
- fixed build warning with NETPOLL enabled
Changes in v3:
- removed the last patch since it causes problems with bcm_sf2/b53 in a
dual-CPU case (root cause known, proper fix underway)
- removed dsa_ds_get_cpu_dp()
Changes in v2:
- added Reviewed-by tags
- assign port->cpu_dp earlier before ops->setup() has run
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper function which will return a reference to the CPU
port used in a dsa_switch_tree. Right now this is a singleton, but this
will change once we introduce multi-CPU port support, so ease the
transition by converting the affected code paths.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports with DSA, have the
dsa_port structure know which CPU it is associated with. This will be
important in order to make sure the correct CPU is used for transmission
of the frames. If not for functional reasons, for performance (e.g: load
balancing) and forwarding decisions.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate master_ethtool_ops and master_orig_ethtool_ops into struct
dsa_port in order to be both consistent, and make things self contained
within the dsa_port structure.
This is a preliminary change to supporting multiple CPU port interfaces.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in the connect()
handler of the AF_CAIF socket. Since the syscall doesn't enforce a minimum
size of the corresponding memory region, very short sockaddrs (zero or one
byte long) result in operating on uninitialized memory while referencing
sa_family.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SF bit is not cleared in PL_INT_CAUSE, subsequent non-data
interrupts are not raised. Enable SF bit in Global Interrupt
Mask and handle it as non-fatal and hence eventually clear it.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_mdio_parse_addr() helper function is useful to other code, but
the module dependency chain causes issues. To work around this, we can
move of_mdio_parse_addr() to be an inline function in the header file.
This gets rid of the dependencies and still allows for the reuse of
code.
Reported-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 342fa19644 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftests depend on using the shell exit code as a mean of
detecting the success or failure of test-binary executed. The
appropiate output "[PASS]" or "[FAIL]" in generated by
tools/testing/selftests/lib.mk.
Notice that the exit code is masked with 255. Thus, be careful if
using the number of errors as the exit code, as 256 errors would be
seen as a success.
There are two standard defined exit(3) codes:
/usr/include/stdlib.h
#define EXIT_FAILURE 1 /* Failing exit status. */
#define EXIT_SUCCESS 0 /* Successful exit status. */
Fix test_verifier.c to not use the negative value of variable
"results", but instead return EXIT_FAILURE.
Fix test_align.c and test_progs.c to actually use exit codes, before
they were always indicating success regardless of results.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary setting of flag IFF_BROADCAST, since ether_setup
already does this.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* merged net-next back to get a patch from net that another patch
here depends on
* various small improvements/cleanups across the board
* 4-way handshake offload (many thanks to Arend for shepherding that)
* mesh CSA/DFS support in mac80211
* the skb_put_zero() we discussed previously
-----BEGIN PGP SIGNATURE-----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=x2vs
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A couple of weeks worth of updates - looks like things are quiet:
* merged net-next back to get a patch from net that another patch
here depends on
* various small improvements/cleanups across the board
* 4-way handshake offload (many thanks to Arend for shepherding that)
* mesh CSA/DFS support in mac80211
* the skb_put_zero() we discussed previously
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- decrease maximum fragment size, by Matthias Schiffer
- Clean up seqfile writing, by Markus Elfring (2 patches)
- use __func__ in debug messages, by Sven Eckelmann
- Mark tpmeter initializers with __init, by Antonio Quartulli
- ignore loop detection MAC addresses, by Simon Wunderlich
- clean up some return handling, by Simon Wunderlich
- improve ELP throughput value handling for WiFi neighbors
in BATMAN V/ELP, by Sven Eckelmann (2 patches)
-----BEGIN PGP SIGNATURE-----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=i0xq
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20170613' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- decrease maximum fragment size, by Matthias Schiffer
- Clean up seqfile writing, by Markus Elfring (2 patches)
- use __func__ in debug messages, by Sven Eckelmann
- Mark tpmeter initializers with __init, by Antonio Quartulli
- ignore loop detection MAC addresses, by Simon Wunderlich
- clean up some return handling, by Simon Wunderlich
- improve ELP throughput value handling for WiFi neighbors
in BATMAN V/ELP, by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix rx packet counters for local ARP replies, by Sven Eckelmann
- fix memory leaks for unicast packetes received from another gateway
in bridge loop avoidance, by Andreas Pape
-----BEGIN PGP SIGNATURE-----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=AbYj
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20170613' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- fix rx packet counters for local ARP replies, by Sven Eckelmann
- fix memory leaks for unicast packetes received from another gateway
in bridge loop avoidance, by Andreas Pape
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
-----BEGIN PGP SIGNATURE-----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=S5/1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Some fixes:
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db4446 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
