Steffen Klassert says:
====================
pull request (net): ipsec 2019-04-30
1) Fix an out-of-bound array accesses in __xfrm_policy_unlink.
From YueHaibing.
2) Reset the secpath on failure in the ESP GRO handlers
to avoid dereferencing an invalid pointer on error.
From Myungho Jung.
3) Add and revert a patch that tried to add rcu annotations
to netns_xfrm. From Su Yanjun.
4) Wait for rcu callbacks before freeing xfrm6_tunnel_spi_kmem.
From Su Yanjun.
5) Fix forgotten vti4 ipip tunnel deregistration.
From Jeremy Sowden:
6) Remove some duplicated log messages in vti4.
From Jeremy Sowden.
7) Don't use IPSEC_PROTO_ANY when flushing states because
this will flush only IPsec portocol speciffic states.
IPPROTO_ROUTING states may remain in the lists when
doing net exit. Fix this by replacing IPSEC_PROTO_ANY
with zero. From Cong Wang.
8) Add length check for UDP encapsulation to fix "Oversized IP packet"
warnings on receive side. From Sabrina Dubroca.
9) Fix xfrm interface lookup when the interface is associated to
a vrf layer 3 master device. From Martin Willi.
10) Reload header pointers after pskb_may_pull() in _decode_session4(),
otherwise we may read from uninitialized memory.
11) Update the documentation about xfrm[46]_gc_thresh, it
is not used anymore after the flowcache removal.
From Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no route to an IPv6 dest addr, skb_dst(skb) points
to loopback dev in the case of that the IP6CB(skb)->iif is
enslaved to a vrf. This causes Ip6InNoRoutes to be incremented on the
loopback dev. This also causes the lookup to fail on icmpv6_send() and
the dest unreachable to not sent and Ip6OutNoRoutes gets incremented on
the loopback dev.
To reproduce:
* Gateway configuration:
ip link add dev vrf_258 type vrf table 258
ip link set dev enp0s9 master vrf_258
ip addr add 66:1/64 dev enp0s9
ip -6 route add unreachable default metric 8192 table 258
sysctl -w net.ipv6.conf.all.forwarding=1
sysctl -w net.ipv6.conf.enp0s9.forwarding=1
* Sender configuration:
ip addr add 66::2/64 dev enp0s9
ip -6 route add default via 66::1
and ping 67::1 for example from the sender.
Fix this by counting on the original netdev and reset the skb dst to
force a fresh lookup.
v2: Fix typo of destination address in the repro steps.
v3: Simplify the loopback check (per David Ahern) and use reverse
Christmas tree format (per David Miller).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A request for a flowlabel fails in process or user exclusive mode must
fail if the caller pid or uid does not match. Invert the test.
Previously, the test was unsafe wrt PID recycling, but indeed tested
for inequality: fl1->owner != fl->owner
Fixes: 4f82f45730 ("net ip6 flowlabel: Make owner a union of struct pid* and kuid_t")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arg.result is sometimes used as fib6_result and sometimes used to
hold the rt6_info. Add rt6_info to fib6_result and make the use
of arg.result consistent through ipv6 rules.
The rt6 entry is filled in for lookups returning a dst_entry, but not
for direct fib_lookups that just want a fib6_info.
Fixes: effda4dd97 ("ipv6: Pass fib6_result to fib lookups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib rule actions should return -EAGAIN for the rules to continue to the
next one. A recent change overwrote err with the lookup always returning
0 (future change will make it more like IPv4) which means the rules
stopped at the first (e.g., local table lookup only). Catch and reset err
to -EAGAIN.
Fixes: effda4dd97 ("ipv6: Pass fib6_result to fib lookups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nhc_flags holds the RTNH_F flags for a given nexthop (fib{6}_nh).
All of the RTNH_F_ flags fit in an unsigned char, and since the API to
userspace (rtnh_flags and lower byte of rtm_flags) is 1 byte it can not
grow. Make nhc_flags in fib_nh_common an unsigned char and shrink the
size of the struct by 8, from 56 to 48 bytes.
Update the flags arguments for up netdevice events and fib_nexthop_info
which determines the RTNH_F flags to return on a dump/event. The RTNH_F
flags are passed in the lower byte of rtm_flags which is an unsigned int
so use a temp variable for the flags to fib_nexthop_info and combine
with rtm_flags in the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We suspect some issues involving fib6_ref 0 -> 1 transitions might
cause strange syzbot reports.
Lets convert fib6_ref to refcount_t to catch them earlier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using atomic_inc(), prefer fib6_info_hold()
so that upcoming refcount_t conversion is simpler.
Only fib6_info_alloc() is using atomic_set() since we
just allocated a new object.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to clear f6i->rt6i_exception_bucket right before
freeing f6i.
Note that f6i->rt6i_exception_bucket is properly protected by
f6i->exception_bucket_flushed being set to one in rt6_flush_exceptions()
under the protection of rt6_exception_lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of them have any external callers, make them static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies, might as well handle this directly.
xfrm_afinfo_policy is now 40 bytes on x86_64.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
handle this directly, its only used by ipv6.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Only used by ipv4, we can read the fl4 tos value directly instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The header contains rtnh_ macros so rename the file accordingly.
Allows a later patch to use the nexthop.h name for the new
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIOCGSTAMP/SIOCGSTAMPNS ioctl commands are implemented by many
socket protocol handlers, and all of those end up calling the same
sock_get_timestamp()/sock_get_timestampns() helper functions, which
results in a lot of duplicate code.
With the introduction of 64-bit time_t on 32-bit architectures, this
gets worse, as we then need four different ioctl commands in each
socket protocol implementation.
To simplify that, let's add a new .gettstamp() operation in
struct proto_ops, and move ioctl implementation into the common
sock_ioctl()/compat_sock_ioctl_trans() functions that these all go
through.
We can reuse the sock_get_timestamp() implementation, but generalize
it so it can deal with both native and compat mode, as well as
timeval and timespec structures.
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/lkml/CAK8P3a038aDQQotzua_QtKGhq8O9n+rdiz2=WDCp82ys8eUT+A@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.
There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().
Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.
v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
isn't defined, expand the description in ip-sysctl.txt and remove
unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
pointer to it is needed because of the way proc_do_large_bitmap work.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a NL_SET_ERR_MSG_MOD error message,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling IPv6 on an interface removes existing entries but nothing prevents
new entries from being manually added. To that end, add a new neigh_table
operation, allow_add, that is called on RTM_NEWNEIGH to see if neighbor
entries are allowed on a given device. If IPv6 is disabled on the device,
allow_add returns false and passes a message back to the user via extack.
$ echo 1 > /proc/sys/net/ipv6/conf/eth1/disable_ipv6
$ ip -6 neigh add fe80::4c88:bff:fe21:2704 dev eth1 lladdr de:ad:be:ef:01:01
Error: IPv6 is disabled on this device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_lookup and fib6_table_lookup to take a fib6_result and set
f6i and nh rather than returning a fib6_info. For now both always
return 0.
A later patch set can make these more like the IPv4 counterparts and
return EINVAL, EACCESS, etc based on fib6_type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_table_lookup tracepoint to take the fib6_result and use
the fib6_info and fib6_nh from it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass fib6_result to rt6_select. Instead of returning the fib entry, it
will set f6i and nh based on the lookup.
find_rr_leaf is changed to remove the match option in favor of taking
fib6_result and having __find_rr_leaf set f6i in the result.
In the process, update fib6_info references in __find_rr_leaf to f6i names.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass fib6_result to rt6_device_match with f6i set. rt6_device_match
updates f6i in the result if it finds a better match and sets nh.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_mtu_from_fib6 and fib6_mtu to take a fib6_result over a
fib6_info. Update both to use the fib6_nh from fib6_result.
Since the signature of ip6_mtu_from_fib6 is already changing, add const
to daddr and saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rt6_insert_exception to take a fib6_result over a fib6_info.
Change ort to f6i from the fib6_result and rename to better reflect
what it references (a fib6_info).
Since this function is already getting changed, update the comments
to reference fib6_info variables rather than the older rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all callers are update to have a fib6_result, pass it down
to ip6_rt_get_dev_rcu, ip6_rt_copy_init, and ip6_rt_init_dst.
In the process, change ort to f6i in ip6_rt_copy_init to make it
clear it is a reference to a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ip6_rt_pcpu_alloc, rt6_get_pcpu_route and rt6_make_pcpu_route
to a fib6_result over a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_create_rt_rcu to take fib6_result over a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_rt_cache_alloc to take a fib6_result over a fib6_info.
Since ip6_rt_cache_alloc is only the caller, update the
rt6_is_gw_or_nonexthop helper to take fib6_result.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify rt6_find_cached_rt for the fast path cases and pass fib6_result
to rt6_find_cached_rt. Rename the local return variable to ret to maintain
consisting with fib6_result name.
Update the comment in rt6_find_cached_rt to reference the new names in
a fib6_info vs the old name when fib entries were an rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.
Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.
Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.
This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the review of 0b34eb0043 ("ipv6: Refactor __ip6_route_redirect"),
Martin noted that the flowi6_oif compare is moved to the new helper and
should be removed from __ip6_route_redirect. Fix the oversight.
Fixes: 0b34eb0043 ("ipv6: Refactor __ip6_route_redirect")
Reported-by: Martin Lau <kafai@fb.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to udpv6_pre_connect()
is shorter than sizeof("struct sockaddr"->sa_family) bytes.
(This patch is bogus if it is guaranteed that udpv6_pre_connect() is
always called after checking "struct sockaddr"->sa_family. In that case,
we want a comment why we don't need to check valid address length here.)
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the nexthop evaluation of a fib entry to a helper that can be
leveraged for each fib6_nh in a multipath nexthop object.
In the move, 'continue' statements means the helper returns false
(loop should continue) and 'break' means return true (found the entry
of interest).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the device and gateway checks in the fib6_next loop to a helper
that can be called per fib6_nh entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the siblings and fib6_multipath_select after the null entry check
since a null entry can not have siblings.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the fib6_null_entry handling in ip6_pol_route_lookup.
rt6_device_match can return fib6_null_entry, but fib6_multipath_select
can not. Consolidate the fib6_null_entry handling and on the final
null_entry check set rt and goto out - no need to defer to a second
check after rt6_find_cached_rt.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
find_rr_leaf has 3 loops over fib_entries calling find_match. The loops
are very similar with differences in start point and whether the metric
is evaluated:
1. start at rr_head, no extra loop compare, check fib metric
2. start at leaf, compare rt against rr_head, check metric
3. start at cont (potential saved point from earlier loops), no
extra loop compare, no metric check
Create 1 loop that is called 3 different times. This will make a
later change with multipath nexthop objects much simpler.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
find_match primarily needs a fib6_nh (and fib6_flags which it passes
through to rt6_score_route). Move fib6_check_expired up to the call
sites so find_match is only called for relevant entries. Remove the
match argument which is mostly a pass through and use the return
boolean to decide if match gets set in the call sites.
The end result is a helper that can be called per fib6_nh struct
which is needed once fib entries reference nexthop objects that
have more than one fib6_nh.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_score_route only needs the fib6_flags and nexthop data. Change
it accordingly. Allows re-use later for nexthop based fib6_nh.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_probe sends probes for gateways in a nexthop. As such it really
depends on a fib6_nh, not a fib entry. Move last_probe to fib6_nh and
update rt6_probe to a fib6_nh struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_check_dev is a simpler helper with only 1 caller. Fold the code
into rt6_score_route.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change rt6_check_neigh to take a fib6_nh instead of a fib entry.
Move the check on fib_flags and whether the nexthop has a gateway
up to the one caller.
Remove the inline from the definition as well. Not necessary.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have separate modules for this.
before:
text data bss dec filename
2038 1168 0 3206 net/ipv4/netfilter/ipt_MASQUERADE.ko
1526 1024 0 2550 net/ipv6/netfilter/ip6t_MASQUERADE.ko
after:
text data bss dec filename
2521 1296 0 3817 net/netfilter/xt_MASQUERADE.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Both are now implemented by nf_nat_masquerade.c, so no need to keep
different headers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove
erspan header. This can determine a possible use-after-free accessing
pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header
Fixes: 1d7e2ed22f ("net: erspan: refactor existing erspan code")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch allows an IPv6 gateway with an IPv4 route. The neighbor
entry will exist in the v6 ndisc table and the cached header will contain
the ipv6 protocol which is wrong for an IPv4 packet. For an IPv4 packet to
use the v6 neighbor entry, neigh_output needs to skip the cached header
and just use the output callback for the neigh entry.
A future patchset can look at expanding the hh_cache to handle 2
protocols. For now, IPv6 gateways with an IPv4 route will take the
extra overhead of generating the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the gateway in a fib_nh_common to be from a different address
family than the outer fib{6}_nh. To that end, replace nhc_has_gw with
nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family.
Now nhc_family is used to know if the nh_common is part of a fib_nh
or fib6_nh (used for container_of to get to route family specific data),
and nhc_gw_family represents the address family for the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_nh_init and fib6_nh_release to ipv6_stubs. If fib6_nh_init fails,
callers should not invoke fib6_nh_release, so there is no reason to have
a dummy stub for the IPv6 is not enabled case.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
very little code, so it really doesn't make sense to have extra
modules or even a kconfig knob for this.
Merge them and make functionality available unconditionally.
The merge makes inet family route support trivial, so add it
as well here.
Before:
text data bss dec hex filename
835 832 0 1667 683 nft_chain_route_ipv4.ko
870 832 0 1702 6a6 nft_chain_route_ipv6.ko
111568 2556 529 114653 1bfdd nf_tables.ko
After:
text data bss dec hex filename
113133 2556 529 116218 1c5fa nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After commit a297569fe0 ("net/udp: do not touch skb->peeked unless
really needed") the 'peeked' argument of __skb_try_recv_datagram()
and friends is always equal to !!'flags & MSG_PEEK'.
Since such argument is really a boolean info, and the callers have
already 'flags & MSG_PEEK' handy, we can remove it and clean-up the
code a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is now only 4 bytes, so its more efficient
to cache a copy rather than its address.
No significant size difference in allmodconfig vmlinux.
With non-modular kernel that has all XFRM options enabled, this
series reduces vmlinux image size by ~11kb. All xfrm_mode
indirections are gone and all modes are built-in.
before (ipsec-next master):
text data bss dec filename
21071494 7233140 11104324 39408958 vmlinux.master
after this series:
21066448 7226772 11104324 39397544 vmlinux.patched
With allmodconfig kernel, the size increase is only 362 bytes,
even all the xfrm config options removed in this series are
modular.
before:
text data bss dec filename
15731286 6936912 4046908 26715106 vmlinux.master
after this series:
15731492 6937068 4046908 26715468 vmlinux
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
after previous changes, xfrm_mode contains no function pointers anymore
and all modules defining such struct contain no code except an init/exit
functions to register the xfrm_mode struct with the xfrm core.
Just place the xfrm modes core and remove the modules,
the run-time xfrm_mode register/unregister functionality is removed.
Before:
text data bss dec filename
7523 200 2364 10087 net/xfrm/xfrm_input.o
40003 628 440 41071 net/xfrm/xfrm_state.o
15730338 6937080 4046908 26714326 vmlinux
7389 200 2364 9953 net/xfrm/xfrm_input.o
40574 656 440 41670 net/xfrm/xfrm_state.o
15730084 6937068 4046908 26714060 vmlinux
The xfrm*_mode_{transport,tunnel,beet} modules are gone.
v2: replace CONFIG_INET6_XFRM_MODE_* IS_ENABLED guards with CONFIG_IPV6
ones rather than removing them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Adds an EXPORT_SYMBOL for afinfo_get_rcu, as it will now be called from
ipv6 in case of CONFIG_IPV6=m.
This change has virtually no effect on vmlinux size, but it reduces
afinfo size and allows followup patch to make xfrm modes const.
v2: mark if (afinfo) tests as likely (Sabrina)
re-fetch afinfo according to inner_mode in xfrm_prepare_input().
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
similar to previous patch: no external module dependencies,
so we can avoid the indirection by placing this in the core.
This change removes the last indirection from xfrm_mode and the
xfrm4|6_mode_{beet,tunnel}.c modules contain (almost) no code anymore.
Before:
text data bss dec hex filename
3957 136 0 4093 ffd net/xfrm/xfrm_output.o
587 44 0 631 277 net/ipv4/xfrm4_mode_beet.o
649 32 0 681 2a9 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 29d net/ipv6/xfrm6_mode_beet.o
599 32 0 631 277 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec hex filename
5359 184 0 5543 15a7 net/xfrm/xfrm_output.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_beet.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_tunnel.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_beet.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_tunnel.o
v2: fold the *encap_add functions into xfrm*_prepare_output
preserve (move) output2 comment (Sabrina)
use x->outer_mode->encap, not inner
fix a build breakage on ppc (kbuild robot)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies on any module, place this in the core.
Increase is about 1800 byte for xfrm_input.o.
The beet helpers get added to internal header, as they can be reused
from xfrm_output.c in the next patch (kernel contains several
copies of them in the xfrm{4,6}_mode_beet.c files).
Before:
text data bss dec filename
5578 176 2364 8118 net/xfrm/xfrm_input.o
1180 64 0 1244 net/ipv4/xfrm4_mode_beet.o
171 40 0 211 net/ipv4/xfrm4_mode_transport.o
1163 40 0 1203 net/ipv4/xfrm4_mode_tunnel.o
1083 52 0 1135 net/ipv6/xfrm6_mode_beet.o
172 40 0 212 net/ipv6/xfrm6_mode_ro.o
172 40 0 212 net/ipv6/xfrm6_mode_transport.o
1056 40 0 1096 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec filename
7373 200 2364 9937 net/xfrm/xfrm_input.o
587 44 0 631 net/ipv4/xfrm4_mode_beet.o
171 32 0 203 net/ipv4/xfrm4_mode_transport.o
649 32 0 681 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 net/ipv6/xfrm6_mode_beet.o
172 32 0 204 net/ipv6/xfrm6_mode_ro.o
172 32 0 204 net/ipv6/xfrm6_mode_transport.o
599 32 0 631 net/ipv6/xfrm6_mode_tunnel.o
v2: pass inner_mode to xfrm_inner_mode_encap_remove to fix
AF_UNSPEC selector breakage (bisected by Benedict Wong)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There are only two versions (tunnel and transport). The ip/ipv6 versions
are only differ in sizeof(iphdr) vs ipv6hdr.
Place this in the core and use x->outer_mode->encap type to call the
correct adjustment helper.
Before:
text data bss dec filename
15730311 6937008 4046908 26714227 vmlinux
After:
15730428 6937008 4046908 26714344 vmlinux
(about 117 byte increase)
v2: use family from x->outer_mode, not inner
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Same is input indirection. Only exception: we need to export
xfrm_outer_mode_output for pktgen.
Increases size of vmlinux by about 163 byte:
Before:
text data bss dec filename
15730208 6936948 4046908 26714064 vmlinux
After:
15730311 6937008 4046908 26714227 vmlinux
xfrm_inner_extract_output has no more external callers, make it static.
v2: add IS_ENABLED(IPV6) guard in xfrm6_prepare_output
add two missing breaks in xfrm_outer_mode_output (Sabrina Dubroca)
add WARN_ON_ONCE for 'call AF_INET6 related output function, but
CONFIG_IPV6=n' case.
make xfrm_inner_extract_output static
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No need for any indirection or abstraction here, both functions
are pretty much the same and quite small, they also have no external
dependencies.
xfrm_prepare_input can then be made static.
With allmodconfig build, size increase of vmlinux is 25 byte:
Before:
text data bss dec filename
15730207 6936924 4046908 26714039 vmlinux
After:
15730208 6936948 4046908 26714064 vmlinux
v2: Fix INET_XFRM_MODE_TRANSPORT name in is-enabled test (Sabrina Dubroca)
change copied comment to refer to transport and network header,
not skb->{h,nh}, which don't exist anymore. (Sabrina)
make xfrm_prepare_input static (Eyal Birger)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Now that we have the family available directly in the
xfrm_mode struct, we can use that and avoid one extra dereference.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be useful to know if we're supposed to decode ipv4 or ipv6.
While at it, make the unregister function return void, all module_exit
functions did just BUG(); there is never a point in doing error checks
if there is no way to handle such error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch changes rhashtables to use a bit_spin_lock on BIT(1) of the
bucket pointer to lock the hash chain for that bucket.
The benefits of a bit spin_lock are:
- no need to allocate a separate array of locks.
- no need to have a configuration option to guide the
choice of the size of this array
- locking cost is often a single test-and-set in a cache line
that will have to be loaded anyway. When inserting at, or removing
from, the head of the chain, the unlock is free - writing the new
address in the bucket head implicitly clears the lock bit.
For __rhashtable_insert_fast() we ensure this always happens
when adding a new key.
- even when lockings costs 2 updates (lock and unlock), they are
in a cacheline that needs to be read anyway.
The cost of using a bit spin_lock is a little bit of code complexity,
which I think is quite manageable.
Bit spin_locks are sometimes inappropriate because they are not fair -
if multiple CPUs repeatedly contend of the same lock, one CPU can
easily be starved. This is not a credible situation with rhashtable.
Multiple CPUs may want to repeatedly add or remove objects, but they
will typically do so at different buckets, so they will attempt to
acquire different locks.
As we have more bit-locks than we previously had spinlocks (by at
least a factor of two) we can expect slightly less contention to
go with the slightly better cache behavior and reduced memory
consumption.
To enhance type checking, a new struct is introduced to represent the
pointer plus lock-bit
that is stored in the bucket-table. This is "struct rhash_lock_head"
and is empty. A pointer to this needs to be cast to either an
unsigned lock, or a "struct rhash_head *" to be useful.
Variables of this type are most often called "bkt".
Previously "pprev" would sometimes point to a bucket, and sometimes a
->next pointer in an rhash_head. As these are now different types,
pprev is NULL when it would have pointed to the bucket. In that case,
'blk' is used, together with correct locking protocol.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Export fib_nexthop_info and fib_add_nexthop for use by IPv6 code.
Remove rt6_nexthop_info and rt6_add_nexthop in favor of the IPv4
versions. Update fib_nexthop_info for IPv6 linkdown check and
RTA_GATEWAY for AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a5 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device type for ip6 tunnels is set to
ARPHRD_TUNNEL6. However, the ip4ip6_err function
is expecting the device type of the tunnel to be
ARPHRD_TUNNEL. Since the device types do not
match, the function exits and the ICMP error
packet is not sent to the originating host. Note
that the device type for IPv4 tunnels is set to
ARPHRD_TUNNEL.
Fix is to expect a tunnel device type of
ARPHRD_TUNNEL6 instead. Now the tunnel device
type matches and the ICMP error packet is sent
to the originating host.
Signed-off-by: Sheena Mira-ato <sheena.mira-ato@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that struct ipv6_pinfo is not located as we think.
inet6_sk_generic() and tcp_inet6_sk() disagree on 32bit kernels by 4-bytes,
because struct tcp_sock has 8-bytes alignment,
but ipv6_pinfo size is not a multiple of 8.
sizeof(struct ipv6_pinfo): 116 (not padded to 8)
I actually first coded tcp_inet6_sk() as this patch does, but thought
that "container_of(tcp_sk(sk), struct tcp6_sock, tcp)" was cleaner.
As Julian told me : Nobody should use tcp6_sock.inet6
directly, it should be accessed via tcp_inet6_sk() or inet6_sk().
This happened when we added the first u64 field in struct tcp_sock.
Fixes: 93a77c11ae ("tcp: add tcp_inet6_sk() helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With fib_nh_common in place, move common initialization and release
code into helpers used by both ipv4 and ipv6. For the moment, the init
is just the lwt encap and the release is both the netdev reference and
the the lwt state reference. More will be added later.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib_nh_common struct with common nexthop attributes. Convert
fib_nh and fib6_nh to use it. Use macros to move existing
fib_nh_* references to the new nh_common.nhc_*.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_add_nexthop and rt6_nexthop_info only need the fib6_info for the
gateway flag and the nexthop weight, and the presence of a gateway is now
per-nexthop. Update the signatures to take a fib6_nh and nexthop weight
and better align with the ipv4 versions.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_ignore_linkdown takes a fib6_info but only looks at the net_device
and its IPv6 config. Change it to take a net_device over a fib6_info as
its input argument.
In addition, move it to a header file to make the check inline and usable
later with IPv4 code without going through the ipv6 stub, and rename to
ip6_ignore_linkdown since it is only checking the setting based on the
ipv6 struct on a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new
fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to
the new flag. For IPv6 address the flag is cheaper than checking that
nh_gw is non-0 like IPv4 does.
While this increases fib6_nh by 8-bytes, the effective allocation size of
a fib6_info is unchanged. The 8 bytes is recovered later with a
fib_nh_common change.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fib6_nh cleanup code to a new helper, fib6_nh_release.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, consolidate the fib6_nh initialization into a helper.
As a new standalone function, add a cleanup path to put lwtstate on
error.
To avoid modifying fib6_config flags, move the reject check to a helper
that is invoked once by fib6_nh_init to reset the device and then
again in ip6_route_info_create to set the fib6_flags.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ila_xlat_nl_cmd_flush uses rhashtable walkers allocated from the
stack but it never frees them. This corrupts the walker list of
the hash table.
This patch fixes it.
Reported-by: syzbot+dae72a112334aa65a159@syzkaller.appspotmail.com
Fixes: b6e71bdebb ("ila: Flush netlink command to clear xlat...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Amit Klein and Benny Pinkas, IP ID generation is too weak
and might be used by attackers.
Even with recent net_hash_mix() fix (netns: provide pure entropy for net_hash_mix())
having 64bit key and Jenkins hash is risky.
It is time to switch to siphash and its 128bit keys.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
I introduced a check for xfrm protocol, but according to Herbert
IPSEC_PROTO_ANY should only be used as a wildcard for lookup, so
it should be removed from validate_tmpl().
And, IPSEC_PROTO_ANY is expected to only match 3 IPSec-specific
protocols, this is why xfrm_state_flush() could still miss
IPPROTO_ROUTING, which leads that those entries are left in
net->xfrm.state_all before exit net. Fix this by replacing
IPSEC_PROTO_ANY with zero.
This patch also extracts the check from validate_tmpl() to
xfrm_id_proto_valid() and uses it in parse_ipsecrequest().
With this, no other protocols should be added into xfrm.
Fixes: 6a53b75932 ("xfrm: check id proto in validate_tmpl()")
Reported-by: syzbot+0bf0519d6e0de15914fe@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Often times, recvmsg() system calls and BH handling for a particular
TCP socket are done on different cpus.
This means the incoming skb had to be allocated on a cpu,
but freed on another.
This incurs a high spinlock contention in slab layer for small rpc,
but also a high number of cache line ping pongs for larger packets.
A full size GRO packet might use 45 page fragments, meaning
that up to 45 put_page() can be involved.
More over performing the __kfree_skb() in the recvmsg() context
adds a latency for user applications, and increase probability
of trapping them in backlog processing, since the BH handler
might found the socket owned by the user.
This patch, combined with the prior one increases the rpc
performance by about 10 % on servers with large number of cores.
(tcp_rr workload with 10,000 flows and 112 threads reach 9 Mpps
instead of 8 Mpps)
This also increases single bulk flow performance on 40Gbit+ links,
since in this case there are often two cpus working in tandem :
- CPU handling the NIC rx interrupts, feeding the receive queue,
and (after this patch) freeing the skbs that were consumed.
- CPU in recvmsg() system call, essentially 100 % busy copying out
data to user space.
Having at most one skb in a per-socket cache has very little risk
of memory exhaustion, and since it is protected by socket lock,
its management is essentially free.
Note that if rps/rfs is used, we do not enable this feature, because
there is high chance that the same cpu is handling both the recvmsg()
system call and the TCP rx path, but that another cpu did the skb
allocations in the device driver right before the RPS/RFS logic.
To properly handle this case, it seems we would need to record
on which cpu skb was allocated, and use a different channel
to give skbs back to this cpu.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net and null_fallback are redundant. Remove null_fallback in favor of
!net check.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change addrconf_f6i_alloc to generate a fib6_config and call
ip6_route_info_create. addrconf_f6i_alloc is the last caller to
fib6_info_alloc besides ip6_route_info_create, and there is no
reason for it to do its own initialization on a fib6_info.
Host routes need to be created even if the device is down, so add a
new flag, fc_ignore_dev_down, to fib6_config and update fib6_nh_init
to not error out if device is not up.
Notes on the conversion:
- ip_fib_metrics_init is the same as fib6_config has fc_mx set to NULL
and fc_mx_len set to 0
- dst_nocount is handled by the RTF_ADDRCONF flag
- dst_host is handled by fc_dst_len = 128
nh_gw does not get set after the conversion to ip6_route_info_create
but it should not be set in addrconf_f6i_alloc since this is a host
route not a gateway route.
Everything else is a straight forward map between fib6_info and
fib6_config.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_info_create is a low level function for ensuring fc_metric is
set. Move the check and default setting to the 2 locations that do not
already set fc_metric before calling ip6_route_info_create. This is
required for the next patch which moves addrconf allocations to
ip6_route_info_create and want the metric for host routes to be 0.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) Remove a direct dependency with IPv6 introduced by the
sip_external_media feature, from Alin Nastac.
2) Fix bogus ENOENT when removing interval elements from set.
3) Set transport_header from br_netfilter to mimic the stack
behaviour, this partially fixes a checksum validation bug
from the SCTP connection tracking, from Xin Long.
4) Fix undefined reference to symbol in xt_TEE, due to missing
Kconfig dependencies, from Arnd Bergmann.
5) Check for NULL in skb_header_pointer() calls in ip6t_shr,
from Kangjie Lu.
6) Fix bogus EBUSY when removing an existing conntrack helper from
a transaction.
7) Fix module autoload of the redirect extension.
8) Remove duplicated transition in flowtable diagram in the existing
documentation.
9) Missing .release_ops call from error path in newrule() which
results module refcount leak, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to icmp_echo_ignore_multicast, there is a need to also
prevent responding to pings to anycast addresses for security.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianlin reported a crash:
[ 381.484332] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
[ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160
[ 382.009615] Call Trace:
[ 382.020762] <IRQ>
[ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0
[ 382.050984] ip6_redirect+0xb6/0xf0
[ 382.066731] icmpv6_notify+0xca/0x190
[ 382.083185] ndisc_redirect_rcv+0x10f/0x160
[ 382.102569] ndisc_rcv+0xfb/0x100
[ 382.117725] icmpv6_rcv+0x3f2/0x520
[ 382.133637] ip6_input_finish+0xbf/0x460
[ 382.151634] ip6_input+0x3b/0xb0
[ 382.166097] ipv6_rcv+0x378/0x4e0
It was caused by the lookup function __ip6_route_redirect() returns NULL in
fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL.
So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry
instead of NULL.
v1->v2:
- move down 'fallback:' to make it more readable.
Fixes: e873e4b9cc ("ipv6: use fib6_info_hold_safe() when necessary")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 has icmp_echo_ignore_broadcast to prevent responding to broadcast pings.
IPv6 needs a similar mechanism.
v1->v2:
- Remove NET_IPV6_ICMP_ECHO_IGNORE_MULTICAST.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
