Currently cgroup_writeback_by_id calls mem_cgroup_wb_stats() to get dirty
pages for a memcg. However mem_cgroup_wb_stats() does a lot more than
just get the number of dirty pages. Just directly get the number of dirty
pages instead of calling mem_cgroup_wb_stats(). Also
cgroup_writeback_by_id() is only called for best-effort dirty flushing, so
remove the unused 'nr' parameter and no need to explicitly flush memcg
stats.
Link: https://lkml.kernel.org/r/20210722182627.2267368-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we trigger writeback bandwidth estimation from
balance_dirty_pages() and from wb_writeback(). However neither of these
need to trigger when the system is relatively idle and writeback is
triggered e.g. from fsync(2). Make sure writeback estimates happen
reliably by triggering them from do_writepages().
Link: https://lkml.kernel.org/r/20210713104716.22868-2-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Michael Stapelberg <stapelberg+linux@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "writeback: Fix bandwidth estimates", v4.
Fix estimate of writeback throughput when device is not fully busy doing
writeback. Michael Stapelberg has reported that such workload (e.g.
generated by linking) tends to push estimated throughput down to 0 and as
a result writeback on the device is practically stalled.
The first three patches fix the reported issue, the remaining two patches
are unrelated cleanups of problems I've noticed when reading the code.
This patch (of 4):
Track number of inodes under writeback for each bdi_writeback structure.
We will use this to decide whether wb does any IO and so we can estimate
its writeback throughput. In principle we could use number of pages under
writeback (WB_WRITEBACK counter) for this however normal percpu counter
reads are too inaccurate for our purposes and summing the counter is too
expensive.
Link: https://lkml.kernel.org/r/20210713104519.16394-1-jack@suse.cz
Link: https://lkml.kernel.org/r/20210713104716.22868-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Michael Stapelberg <stapelberg+linux@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmDcl7AACgkQnJ2qBz9k
QNnsBQf+LBAPsfykQ/f8EdHErO1lfbVTmwf2g/JzTkjrIVZTZ6Ic47aCIiFxgHU2
Js9ufaPxpsbbopzpn2PAoCUzxNsZDqgXtnC03MOUAqoSFbAvgLHz2sQwjqeYJUGQ
P6n7VipEA/qBVpQI5zeCUhHYcahoNrRjSLzaFnE2Z8CrQYQ6Ry9gVEhduvu2OTru
62cWlAWlTJfx/FcR1Y0F/ZznnNSKMiAHcEe3F6Beztplg2ooq+z6FclJYrkmnxMq
SXSOsqTCdi1/oFx36NpvLkykrIS9I7N/iqCnKwbm6X+nyZZKyAwYZhWVqkbozPPu
+u1Ppq8o0IuWwEA6/UAmxgAO3m/Gkw==
=tn0h
-----END PGP SIGNATURE-----
Merge tag 'fs_for_v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull misc fs updates from Jan Kara:
"The new quotactl_fd() syscall (remake of quotactl_path() syscall that
got introduced & disabled in 5.13 cycle), and couple of udf, reiserfs,
isofs, and writeback fixes and cleanups"
* tag 'fs_for_v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
writeback: fix obtain a reference to a freeing memcg css
quota: remove unnecessary oom message
isofs: remove redundant continue statement
quota: Wire up quotactl_fd syscall
quota: Change quotactl_path() systcall to an fd-based one
reiserfs: Remove unneed check in reiserfs_write_full_page()
udf: Fix NULL pointer dereference in udf_symlink function
reiserfs: add check for invalid 1st journal block
Asynchronously try to release dying cgwbs by switching attached inodes to
the nearest living ancestor wb. It helps to get rid of per-cgroup
writeback structures themselves and of pinned memory and block cgroups,
which are significantly larger structures (mostly due to large per-cpu
statistics data). This prevents memory waste and helps to avoid different
scalability problems caused by large piles of dying cgroups.
Reuse the existing mechanism of inode switching used for foreign inode
detection. To speed things up batch up to 115 inode switching in a single
operation (the maximum number is selected so that the resulting struct
inode_switch_wbs_context can fit into 1024 bytes). Because every
switching consists of two steps divided by an RCU grace period, it would
be too slow without batching. Please note that the whole batch counts as
a single operation (when increasing/decreasing isw_nr_in_flight). This
allows to keep umounting working (flush the switching queue), however
prevents cleanups from consuming the whole switching quota and effectively
blocking the frn switching.
A cgwb cleanup operation can fail due to different reasons (e.g. not
enough memory, the cgwb has an in-flight/pending io, an attached inode in
a wrong state, etc). In this case the next scheduled cleanup will make a
new attempt. An attempt is made each time a new cgwb is offlined (in
other words a memcg and/or a blkcg is deleted by a user). In the future
an additional attempt scheduled by a timer can be implemented.
[guro@fb.com: replace open-coded "115" with arithmetic]
Link: https://lkml.kernel.org/r/YMEcSBcq/VXMiPPO@carbon.dhcp.thefacebook.com
[guro@fb.com: add smp_mb() to inode_prepare_wbs_switch()]
Link: https://lkml.kernel.org/r/YMFa+guFw7OFjf3X@carbon.dhcp.thefacebook.com
[willy@infradead.org: fix documentation]
Link: https://lkml.kernel.org/r/20210615200242.1716568-2-willy@infradead.org
Link: https://lkml.kernel.org/r/20210608230225.2078447-9-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently only a single inode can be switched to another writeback
structure at once. That means to switch an inode a separate
inode_switch_wbs_context structure must be allocated, and a separate rcu
callback and work must be scheduled.
It's fine for the existing ad-hoc switching, which is not happening that
often, but sub-optimal for massive switching required in order to release
a writeback structure. To prepare for it, let's add a support for
switching multiple inodes at once.
Instead of containing a single inode pointer, inode_switch_wbs_context
will contain a NULL-terminated array of inode pointers.
inode_do_switch_wbs() will be called for each inode.
To optimize the locking bdi->wb_switch_rwsem, old_wb's and new_wb's
list_locks will be acquired and released only once altogether for all
inodes. wb_wakeup() will be also be called only once. Instead of calling
wb_put(old_wb) after each successful switch, wb_put_many() is introduced
and used.
Link: https://lkml.kernel.org/r/20210608230225.2078447-8-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Dennis Zhou <dennis@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split out the functional part of the inode_switch_wbs_work_fn() function
as inode_do switch_wbs() to reuse it later for switching inodes attached
to dying cgwbs.
This commit doesn't bring any functional changes.
Link: https://lkml.kernel.org/r/20210608230225.2078447-7-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Zhou <dennis@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently there is no way to iterate over inodes attached to a specific
cgwb structure. It limits the ability to efficiently reclaim the
writeback structure itself and associated memory and block cgroup
structures without scanning all inodes belonging to a sb, which can be
prohibitively expensive.
While dirty/in-active-writeback an inode belongs to one of the
bdi_writeback's io lists: b_dirty, b_io, b_more_io and b_dirty_time. Once
cleaned up, it's removed from all io lists. So the inode->i_io_list can
be reused to maintain the list of inodes, attached to a bdi_writeback
structure.
This patch introduces a new wb->b_attached list, which contains all inodes
which were dirty at least once and are attached to the given cgwb. Inodes
attached to the root bdi_writeback structures are never placed on such
list. The following patch will use this list to try to release cgwbs
structures more efficiently.
Link: https://lkml.kernel.org/r/20210608230225.2078447-6-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Zhou <dennis@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Inode's wb switching requires two steps divided by an RCU grace period.
It's currently implemented as an RCU callback inode_switch_wbs_rcu_fn(),
which schedules inode_switch_wbs_work_fn() as a work.
Switching to the rcu_work API allows to do the same in a cleaner and
slightly shorter form.
Link: https://lkml.kernel.org/r/20210608230225.2078447-5-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Zhou <dennis@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
isw_nr_in_flight is used to determine whether the inode switch queue
should be flushed from the umount path. Currently it's increased after
grabbing an inode and even scheduling the switch work. It means the
umount path can walk past cleanup_offline_cgwb() with active inode
references, which can result in a "Busy inodes after unmount." message and
use-after-free issues (with inode->i_sb which gets freed).
Fix it by incrementing isw_nr_in_flight before doing anything with the
inode and decrementing in the case when switching wasn't scheduled.
The problem hasn't yet been seen in the real life and was discovered by
Jan Kara by looking into the code.
Link: https://lkml.kernel.org/r/20210608230225.2078447-4-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Jan Kara <jack@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A full memory barrier is required between clearing SB_ACTIVE flag in
generic_shutdown_super() and checking isw_nr_in_flight in
cgroup_writeback_umount(), otherwise a new switch operation might be
scheduled after atomic_read(&isw_nr_in_flight) returned 0. This would
result in a non-flushed isw_wq, and a potential crash.
The problem hasn't yet been seen in the real life and was discovered by
Jan Kara by looking into the code.
Link: https://lkml.kernel.org/r/20210608230225.2078447-3-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "cgroup, blkcg: prevent dirty inodes to pin dying memory cgroups", v9.
When an inode is getting dirty for the first time it's associated with a
wb structure (see __inode_attach_wb()). It can later be switched to
another wb (if e.g. some other cgroup is writing a lot of data to the
same inode), but otherwise stays attached to the original wb until being
reclaimed.
The problem is that the wb structure holds a reference to the original
memory and blkcg cgroups. So if an inode has been dirty once and later is
actively used in read-only mode, it has a good chance to pin down the
original memory and blkcg cgroups forever. This is often the case with
services bringing data for other services, e.g. updating some rpm
packages.
In the real life it becomes a problem due to a large size of the memcg
structure, which can easily be 1000x larger than an inode. Also a really
large number of dying cgroups can raise different scalability issues, e.g.
making the memory reclaim costly and less effective.
To solve the problem inodes should be eventually detached from the
corresponding writeback structure. It's inefficient to do it after every
writeback completion. Instead it can be done whenever the original memory
cgroup is offlined and writeback structure is getting killed. Scanning
over a (potentially long) list of inodes and detach them from the
writeback structure can take quite some time. To avoid scanning all
inodes, attached inodes are kept on a new list (b_attached). To make it
less noticeable to a user, the scanning and switching is performed from a
work context.
Big thanks to Jan Kara, Dennis Zhou, Hillf Danton and Tejun Heo for their
ideas and contribution to this patchset.
This patch (of 8):
If an inode's state has I_WILL_FREE flag set, the inode will be freed
soon, so there is no point in trying to switch the inode to a different
cgwb.
I_WILL_FREE was ignored since the introduction of the inode switching, so
it looks like it doesn't lead to any noticeable issues for a user. This
is why the patch is not intended for a stable backport.
Link: https://lkml.kernel.org/r/20210608230225.2078447-1-guro@fb.com
Link: https://lkml.kernel.org/r/20210608230225.2078447-2-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Jan Kara <jack@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Dennis Zhou <dennis@kernel.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The caller of wb_get_create() should pin the memcg, because
wb_get_create() relies on this guarantee. The rcu read lock
only can guarantee that the memcg css returned by css_from_id()
cannot be released, but the reference of the memcg can be zero.
rcu_read_lock()
memcg_css = css_from_id()
wb_get_create(memcg_css)
cgwb_create(memcg_css)
// css_get can change the ref counter from 0 back to 1
css_get(memcg_css)
rcu_read_unlock()
Fix it by holding a reference to the css before calling
wb_get_create(). This is not a problem I encountered in the
real world. Just the result of a code review.
Fixes: 682aa8e1a6 ("writeback: implement unlocked_inode_to_wb transaction and use it for stat updates")
Link: https://lore.kernel.org/r/20210402091145.80635-1-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
block_dump is an old debugging interface, one of it's functions is used
to print the information about who write which file on disk. If we
enable block_dump through /proc/sys/vm/block_dump and turn on debug log
level, we can gather information about write process name, target file
name and disk from kernel message. This feature is realized in
block_dump___mark_inode_dirty(), it print above information into kernel
message directly when marking inode dirty, so it is noisy and can easily
trigger log storm. At the same time, get the dentry refcount is also not
safe, we found it will lead to deadlock on ext4 file system with
data=journal mode.
After tracepoints has been introduced into the kernel, we got a
tracepoint in __mark_inode_dirty(), which is a better replacement of
block_dump___mark_inode_dirty(). The only downside is that it only trace
the inode number and not a file name, but it probably doesn't matter
because the original printed file name in block_dump is not accurate in
some cases, and we can still find it through the inode number and device
id. So this patch delete the dirting inode part of block_dump feature.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210313030146.2882027-2-yi.zhang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some comments for writeback_single_inode() and
__writeback_single_inode() are outdated or not very helpful, especially
with regards to writeback list handling. Update them.
Link: https://lore.kernel.org/r/20210112190253.64307-10-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
wbc->for_sync implies wbc->sync_mode == WB_SYNC_ALL, so there's no need
to check for both. Just check for WB_SYNC_ALL.
Link: https://lore.kernel.org/r/20210112190253.64307-9-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Improve some comments, and don't bother checking for the I_DIRTY_TIME
flag in the case where we just cleared it.
Also, warn if I_DIRTY_TIME and I_DIRTY_PAGES are passed to
__mark_inode_dirty() at the same time, as this case isn't handled.
Link: https://lore.kernel.org/r/20210112190253.64307-8-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
->dirty_inode is now only called when I_DIRTY_INODE (I_DIRTY_SYNC and/or
I_DIRTY_DATASYNC) is set. However it may still be passed other dirty
flags at the same time, provided that these other flags happened to be
passed to __mark_inode_dirty() at the same time as I_DIRTY_INODE.
This doesn't make sense because there is no reason for filesystems to
care about these extra flags. Nor are filesystems notified about all
updates to these other flags.
Therefore, mask the flags before passing them to ->dirty_inode.
Also properly document ->dirty_inode in vfs.rst.
Link: https://lore.kernel.org/r/20210112190253.64307-7-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
There is no need to call ->dirty_inode for lazytime timestamp updates
(i.e. for __mark_inode_dirty(I_DIRTY_TIME)), since by the definition of
lazytime, filesystems must ignore these updates. Filesystems only need
to care about the updated timestamps when they expire.
Therefore, only call ->dirty_inode when I_DIRTY_INODE is set.
Based on a patch from Christoph Hellwig:
https://lore.kernel.org/r/20200325122825.1086872-4-hch@lst.de
Link: https://lore.kernel.org/r/20210112190253.64307-6-ebiggers@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
Cc: stable@vger.kernel.org
Depends-on: 5afced3bf2 ("writeback: Avoid skipping inode writeback")
Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
BDIs get unregistered during device removal, and this WARN can be
trivially triggered by hot-removing a NVMe device while running fsx
It is otherwise harmless as we still hold a BDI reference, and the
writeback has been shut down already.
Link: https://lore.kernel.org/r/20200928122613.434820-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
Replace the two negative flags that are always used together with a
single positive flag that indicates the writeback capability instead
of two related non-capabilities. Also remove the pointless wrappers
to just check the flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
definition of dirtytime_interval_handler to match its prototype in
linux/writeback.h which fixes the following sparse error/warning:
fs/fs-writeback.c:2189:50: warning: incorrect type in argument 3 (different address spaces)
fs/fs-writeback.c:2189:50: expected void *
fs/fs-writeback.c:2189:50: got void [noderef] __user *buffer
fs/fs-writeback.c:2184:5: error: symbol 'dirtytime_interval_handler' redeclared with different type (incompatible argument 3 (different address spaces)):
fs/fs-writeback.c:2184:5: int extern [addressable] [signed] [toplevel] dirtytime_interval_handler( ... )
fs/fs-writeback.c: note: in included file:
./include/linux/writeback.h:374:5: note: previously declared as:
./include/linux/writeback.h:374:5: int extern [addressable] [signed] [toplevel] dirtytime_interval_handler( ... )
Fixes: 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200907093140.13434-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only use of I_DIRTY_TIME_EXPIRE is to detect in
__writeback_single_inode() that inode got there because flush worker
decided it's time to writeback the dirty inode time stamps (either
because we are syncing or because of age). However we can detect this
directly in __writeback_single_inode() and there's no need for the
strange propagation with I_DIRTY_TIME_EXPIRE flag.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
When we are processing writeback for sync(2), move_expired_inodes()
didn't set any inode expiry value (older_than_this). This can result in
writeback never completing if there's steady stream of inodes added to
b_dirty_time list as writeback rechecks dirty lists after each writeback
round whether there's more work to be done. Fix the problem by using
sync(2) start time is inode expiry value when processing b_dirty_time
list similarly as for ordinarily dirtied inodes. This requires some
refactoring of older_than_this handling which simplifies the code
noticeably as a bonus.
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
CC: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Inode's i_io_list list head is used to attach inode to several different
lists - wb->{b_dirty, b_dirty_time, b_io, b_more_io}. When flush worker
prepares a list of inodes to writeback e.g. for sync(2), it moves inodes
to b_io list. Thus it is critical for sync(2) data integrity guarantees
that inode is not requeued to any other writeback list when inode is
queued for processing by flush worker. That's the reason why
writeback_single_inode() does not touch i_io_list (unless the inode is
completely clean) and why __mark_inode_dirty() does not touch i_io_list
if I_SYNC flag is set.
However there are two flaws in the current logic:
1) When inode has only I_DIRTY_TIME set but it is already queued in b_io
list due to sync(2), concurrent __mark_inode_dirty(inode, I_DIRTY_SYNC)
can still move inode back to b_dirty list resulting in skipping
writeback of inode time stamps during sync(2).
2) When inode is on b_dirty_time list and writeback_single_inode() races
with __mark_inode_dirty() like:
writeback_single_inode() __mark_inode_dirty(inode, I_DIRTY_PAGES)
inode->i_state |= I_SYNC
__writeback_single_inode()
inode->i_state |= I_DIRTY_PAGES;
if (inode->i_state & I_SYNC)
bail
if (!(inode->i_state & I_DIRTY_ALL))
- not true so nothing done
We end up with I_DIRTY_PAGES inode on b_dirty_time list and thus
standard background writeback will not writeback this inode leading to
possible dirty throttling stalls etc. (thanks to Martijn Coenen for this
analysis).
Fix these problems by tracking whether inode is queued in b_io or
b_more_io lists in a new I_SYNC_QUEUED flag. When this flag is set, we
know flush worker has queued inode and we should not touch i_io_list.
On the other hand we also know that once flush worker is done with the
inode it will requeue the inode to appropriate dirty list. When
I_SYNC_QUEUED is not set, __mark_inode_dirty() can (and must) move inode
to appropriate dirty list.
Reported-by: Martijn Coenen <maco@android.com>
Reviewed-by: Martijn Coenen <maco@android.com>
Tested-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Currently, operations on inode->i_io_list are protected by
wb->list_lock. In the following patches we'll need to maintain
consistency between inode->i_state and inode->i_io_list so change the
code so that inode->i_lock protects also all inode's i_io_list handling.
Reviewed-by: Martijn Coenen <maco@android.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: stable@vger.kernel.org # Prerequisite for "writeback: Avoid skipping inode writeback"
Signed-off-by: Jan Kara <jack@suse.cz>
* Fix performance problems found in dioread_nolock now that it is the
default, caused by transaction leaks.
* Clean up fiemap handling in ext4
* Clean up and refactor multiple block allocator (mballoc) code
* Fix a problem with mballoc with a smaller file systems running out
of blocks because they couldn't properly use blocks that had been
reserved by inode preallocation.
* Fixed a race in ext4_sync_parent() versus rename()
* Simplify the error handling in the extent manipulation code
* Make sure all metadata I/O errors are felected to ext4_ext_dirty()'s and
ext4_make_inode_dirty()'s callers.
* Avoid passing an error pointer to brelse in ext4_xattr_set()
* Fix race which could result to freeing an inode on the dirty last
in data=journal mode.
* Fix refcount handling if ext4_iget() fails
* Fix a crash in generic/019 caused by a corrupted extent node
-----BEGIN PGP SIGNATURE-----
iQEyBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl7Ze8kACgkQ8vlZVpUN
gaNChAf4xn0ytFSrweI/S2Sp05G/2L/ocZ2TZZk2ZdGeN1E+ABdSIv/zIF9zuFgZ
/pY/C+fyEZWt4E3FlNO8gJzoEedkzMCMnUhSIfI+wZbcclyTOSNMJtnrnJKAEtVH
HOvGZJmg357jy407RCGhZpJ773nwU2xhBTr5OFxvSf9mt/vzebxIOnw5D7HPlC1V
Fgm6Du8q+tRrPsyjv1Yu4pUEVXMJ7qUcvt326AXVM3kCZO1Aa5GrURX0w3J4mzW1
tc1tKmtbLcVVYTo9CwHXhk/edbxrhAydSP2iACand3tK6IJuI6j9x+bBJnxXitnr
vsxsfTYMG18+2SxrJ9LwmagqmrRq
=HMTs
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"A lot of bug fixes and cleanups for ext4, including:
- Fix performance problems found in dioread_nolock now that it is the
default, caused by transaction leaks.
- Clean up fiemap handling in ext4
- Clean up and refactor multiple block allocator (mballoc) code
- Fix a problem with mballoc with a smaller file systems running out
of blocks because they couldn't properly use blocks that had been
reserved by inode preallocation.
- Fixed a race in ext4_sync_parent() versus rename()
- Simplify the error handling in the extent manipulation code
- Make sure all metadata I/O errors are felected to
ext4_ext_dirty()'s and ext4_make_inode_dirty()'s callers.
- Avoid passing an error pointer to brelse in ext4_xattr_set()
- Fix race which could result to freeing an inode on the dirty last
in data=journal mode.
- Fix refcount handling if ext4_iget() fails
- Fix a crash in generic/019 caused by a corrupted extent node"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (58 commits)
ext4: avoid unnecessary transaction starts during writeback
ext4: don't block for O_DIRECT if IOCB_NOWAIT is set
ext4: remove the access_ok() check in ext4_ioctl_get_es_cache
fs: remove the access_ok() check in ioctl_fiemap
fs: handle FIEMAP_FLAG_SYNC in fiemap_prep
fs: move fiemap range validation into the file systems instances
iomap: fix the iomap_fiemap prototype
fs: move the fiemap definitions out of fs.h
fs: mark __generic_block_fiemap static
ext4: remove the call to fiemap_check_flags in ext4_fiemap
ext4: split _ext4_fiemap
ext4: fix fiemap size checks for bitmap files
ext4: fix EXT4_MAX_LOGICAL_BLOCK macro
add comment for ext4_dir_entry_2 file_type member
jbd2: avoid leaking transaction credits when unreserving handle
ext4: drop ext4_journal_free_reserved()
ext4: mballoc: use lock for checking free blocks while retrying
ext4: mballoc: refactor ext4_mb_good_group()
ext4: mballoc: introduce pcpu seqcnt for freeing PA to improve ENOSPC handling
ext4: mballoc: refactor ext4_mb_discard_preallocations()
...
Ext4 needs to remove inode from writeback lists after it is out of
visibility of its journalling machinery (which can still dirty the
inode). Export inode_io_list_del() for it.
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200421085445.5731-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
-----BEGIN PGP SIGNATURE-----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=HYf4
-----END PGP SIGNATURE-----
Merge tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Core block changes that have been queued up for this release:
- Remove dead blk-throttle and blk-wbt code (Guoqing)
- Include pid in blktrace note traces (Jan)
- Don't spew I/O errors on wouldblock termination (me)
- Zone append addition (Johannes, Keith, Damien)
- IO accounting improvements (Konstantin, Christoph)
- blk-mq hardware map update improvements (Ming)
- Scheduler dispatch improvement (Salman)
- Inline block encryption support (Satya)
- Request map fixes and improvements (Weiping)
- blk-iocost tweaks (Tejun)
- Fix for timeout failing with error injection (Keith)
- Queue re-run fixes (Douglas)
- CPU hotplug improvements (Christoph)
- Queue entry/exit improvements (Christoph)
- Move DMA drain handling to the few drivers that use it (Christoph)
- Partition handling cleanups (Christoph)"
* tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block: (127 commits)
block: mark bio_wouldblock_error() bio with BIO_QUIET
blk-wbt: rename __wbt_update_limits to wbt_update_limits
blk-wbt: remove wbt_update_limits
blk-throttle: remove tg_drain_bios
blk-throttle: remove blk_throtl_drain
null_blk: force complete for timeout request
blk-mq: drain I/O when all CPUs in a hctx are offline
blk-mq: add blk_mq_all_tag_iter
blk-mq: open code __blk_mq_alloc_request in blk_mq_alloc_request_hctx
blk-mq: use BLK_MQ_NO_TAG in more places
blk-mq: rename BLK_MQ_TAG_FAIL to BLK_MQ_NO_TAG
blk-mq: move more request initialization to blk_mq_rq_ctx_init
blk-mq: simplify the blk_mq_get_request calling convention
blk-mq: remove the bio argument to ->prepare_request
nvme: force complete cancelled requests
blk-mq: blk-mq: provide forced completion method
block: fix a warning when blkdev.h is included for !CONFIG_BLOCK builds
block: blk-crypto-fallback: remove redundant initialization of variable err
block: reduce part_stat_lock() scope
block: use __this_cpu_add() instead of access by smp_processor_id()
...
After an NFS page has been written it is considered "unstable" until a
COMMIT request succeeds. If the COMMIT fails, the page will be
re-written.
These "unstable" pages are currently accounted as "reclaimable", either
in WB_RECLAIMABLE, or in NR_UNSTABLE_NFS which is included in a
'reclaimable' count. This might have made sense when sending the COMMIT
required a separate action by the VFS/MM (e.g. releasepage() used to
send a COMMIT). However now that all writes generated by ->writepages()
will automatically be followed by a COMMIT (since commit 919e3bd9a8
("NFS: Ensure we commit after writeback is complete")) it makes more
sense to treat them as writeback pages.
So this patch removes NR_UNSTABLE_NFS and accounts unstable pages in
NR_WRITEBACK and WB_WRITEBACK.
A particular effect of this change is that when
wb_check_background_flush() calls wb_over_bg_threshold(), the latter
will report 'true' a lot less often as the 'unstable' pages are no
longer considered 'dirty' (as there is nothing that writeback can do
about them anyway).
Currently wb_check_background_flush() will trigger writeback to NFS even
when there are relatively few dirty pages (if there are lots of unstable
pages), this can result in small writes going to the server (10s of
Kilobytes rather than a Megabyte) which hurts throughput. With this
patch, there are fewer writes which are each larger on average.
Where the NR_UNSTABLE_NFS count was included in statistics
virtual-files, the entry is retained, but the value is hard-coded as
zero. static trace points and warning printks which mentioned this
counter no longer report it.
[akpm@linux-foundation.org: re-layout comment]
[akpm@linux-foundation.org: fix printk warning]
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Acked-by: Michal Hocko <mhocko@suse.com> [mm]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Link: http://lkml.kernel.org/r/87d06j7gqa.fsf@notabene.neil.brown.name
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name is only printed for a not registered bdi in writeback. Use the
device name there as is more useful anyway for the unlike case that the
warning triggers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Without memcg, there is a one-to-one mapping between the bdi and
bdi_writeback structures. In this world, things are fairly
straightforward; the first thing bdi_unregister() does is to shutdown
the bdi_writeback structure (or wb), and part of that writeback ensures
that no other work queued against the wb, and that the wb is fully
drained.
With memcg, however, there is a one-to-many relationship between the bdi
and bdi_writeback structures; that is, there are multiple wb objects
which can all point to a single bdi. There is a refcount which prevents
the bdi object from being released (and hence, unregistered). So in
theory, the bdi_unregister() *should* only get called once its refcount
goes to zero (bdi_put will drop the refcount, and when it is zero,
release_bdi gets called, which calls bdi_unregister).
Unfortunately, del_gendisk() in block/gen_hd.c never got the memo about
the Brave New memcg World, and calls bdi_unregister directly. It does
this without informing the file system, or the memcg code, or anything
else. This causes the root wb associated with the bdi to be
unregistered, but none of the memcg-specific wb's are shutdown. So when
one of these wb's are woken up to do delayed work, they try to
dereference their wb->bdi->dev to fetch the device name, but
unfortunately bdi->dev is now NULL, thanks to the bdi_unregister()
called by del_gendisk(). As a result, *boom*.
Fortunately, it looks like the rest of the writeback path is perfectly
happy with bdi->dev and bdi->owner being NULL, so the simplest fix is to
create a bdi_dev_name() function which can handle bdi->dev being NULL.
This also allows us to bulletproof the writeback tracepoints to prevent
them from dereferencing a NULL pointer and crashing the kernel if one is
tracing with memcg's enabled, and an iSCSI device dies or a USB storage
stick is pulled.
The most common way of triggering this will be hotremoval of a device
while writeback with memcg enabled is going on. It was triggering
several times a day in a heavily loaded production environment.
Google Bug Id: 145475544
Link: https://lore.kernel.org/r/20191227194829.150110-1-tytso@mit.edu
Link: http://lkml.kernel.org/r/20191228005211.163952-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Chris Mason <clm@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
* https://lore.kernel.org/linux-mm/20190513183053.GA73423@dennisz-mbp/
* http://lkml.kernel.org/r/156355839560.2063.5265687291430814589.stgit@buzz
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: e8a7abf5a5 ("writeback: disassociate inodes from dying bdi_writebacks")
Acked-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
cgroup foreign inode handling has quite a bit of heuristics and
internal states which sometimes makes it difficult to understand
what's going on. Add tracepoints to improve visibility.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Implement cgroup_writeback_by_id() which initiates cgroup writeback
from bdi and memcg IDs. This will be used by memcg foreign inode
flushing.
v2: Use wb_get_lookup() instead of wb_get_create() to avoid creating
spurious wbs.
v3: Interpret 0 @nr as 1.25 * nr_dirty to implement best-effort
flushing while avoding possible livelocks.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
wb_completion is used to track writeback completions. We want to use
it from memcg side for foreign inode flushes. This patch updates it
to remember the target waitq instead of assuming bdi->wb_waitq and
expose it outside of fs-writeback.c.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As inode wb switching may make sync(2) miss some inodes, they're
synchronized using wb_switch_rwsem so that no wb switching happens
while sync(2) is in progress. In addition to synchronizing the actual
switching, the rwsem is also used to prevent queueing new switch
attempts while sync(2) is in progress. This is to avoid queueing too
many instances while the rwsem is held by sync(2). Unfortunately,
this is too agressive and can block wb switching for a long time if
sync(2) is frequent.
The goal is avoiding expolding the number of scheduled switches, not
avoiding scheduling anything. Let's use wb_switch_rwsem only for
synchronizing the actual switching and sync(2) and use
isw_nr_in_flight instead for limiting the maximum number of scheduled
switches. The limit is set to 1024 which should be more than enough
while still avoiding extreme situations.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WB_FRN_TIME_CUT_DIV is used to tell the foreign inode detection logic
to ignore short writeback rounds to prevent getting confused by a
burst of short writebacks. The parameter is currently 2 meaning that
anything smaller than half of the running average writback duration
will be ignored.
This is unnecessarily aggressive. The detection logic uses 16 history
slots and is already reasonably protected against some short bursts
confusing it and the current parameter can lead to tens of seconds of
missed detection depending on the writeback pattern.
Let's change the parameter to 8, so that it only ignores writeback
with are smaller than 12.5% of the current running average.
v2: Add comment explaining what's going on with the foreign detection
parameters.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When writeback IOs are bounced through async layers, the IOs should
only be accounted against the wbc from the original bdi writeback to
avoid confusing cgroup inode ownership arbitration. Add
wbc->no_cgroup_owner to allow disabling wbc cgroup owner accounting.
This will be used make btrfs compression work well with cgroup IO
control.
v2: Renamed from no_wbc_acct to no_cgroup_owner and added comment as
per Jan.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
wbc_account_io() does a very specific job - try to see which cgroup is
actually dirtying an inode and transfer its ownership to the majority
dirtier if needed. The name is too generic and confusing. Let's
rename it to something more specific.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
btrfs is going to use css_put() and wbc helpers to improve cgroup
writeback support. Add dummy css_get() definition and export wbc
helpers to prepare for module and !CONFIG_CGROUP builds.
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
wbc_account_io() collects information on cgroup ownership of writeback
pages to determine which cgroup should own the inode. Pages can stay
associated with dead memcgs but we want to avoid attributing IOs to
dead blkcgs as much as possible as the association is likely to be
stale. However, currently, pages associated with dead memcgs
contribute to the accounting delaying and/or confusing the
arbitration.
Fix it by ignoring pages associated with dead memcgs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
synchronize_rcu() didn't wait for call_rcu() callbacks, so inode wb
switch may not go to the workqueue after synchronize_rcu(). Thus
previous scheduled switches was not finished even flushing the
workqueue, which will cause a NULL pointer dereferenced followed below.
VFS: Busy inodes after unmount of vdd. Self-destruct in 5 seconds. Have a nice day...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000278
evict+0xb3/0x180
iput+0x1b0/0x230
inode_switch_wbs_work_fn+0x3c0/0x6a0
worker_thread+0x4e/0x490
? process_one_work+0x410/0x410
kthread+0xe6/0x100
ret_from_fork+0x39/0x50
Replace the synchronize_rcu() call with a rcu_barrier() to wait for all
pending callbacks to finish. And inc isw_nr_in_flight after call_rcu()
in inode_switch_wbs() to make more sense.
Link: http://lkml.kernel.org/r/20190429024108.54150-1-jiufei.xue@linux.alibaba.com
Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Acked-by: Tejun Heo <tj@kernel.org>
Suggested-by: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
