NX3031 hardware requires local IP addresses for packet
accumulation (LRO). IP address hashing is required to
distinguish a local TCP flow from others (forwarded or
guest).
This patch adds listener for IP and netdev events and
configures IP address in the firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move dma mask update to netxen_start_firmware() so that
if firmware changes across suspend (e.g. file -> flash)
it reflects right dma mask.
o re-read firmware capabilities after firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset consumer of status rings to 0 when cleaning
up sw resources. Status rings are not deleted
during suspend since they have napi objects.
This ensures correct rx processing across suspen-resume.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: fix deadlock on dev close
The tx ring accounting fix in commit cb2107be43
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict firmware reset to following cases -
o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.
This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.
Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all functions run firmware init handshake.
If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This forces every update of tx ring producer to check for
availability of space for next full TSO command. Earlier
firmware control commands didn't care to pause tx queue.
Stop the tx queue if there's not enough space to transmit one full
LSO command left on the tx ring after current transmit. This avoids
returning NETDEV_TX_BUSY after checking distance between producer
and consumer on every cpu.
Restart the tx queue only if we have cleaned up enough tx
descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Pause traffic during mac addr change.
o Enable setting mac address for NX3031.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the distance check between tx ring producer and consumer that
could lead to tx ring wrap around.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o hold the firmware in memory across suspend, since filesystem
may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
for NC-SI.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unnecessary length parameter since register access
width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
functions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for asynchronous events from firmware,
received over one of the rx rings.
Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicate firmware handshake, defer it until first
port (interface) is brought up.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move tx stuff into nx_host_tx_ring structure, this will
help managing multiple tx rings in future.
o sanitize some variable names
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.
The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove max_ prefix from ring sizes, since they don't really
represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
rx ring of 10 gig ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove huge board config structure from each instance, read
only necessary fields from flash.
Replace board_type with port_type (1G/10G), there's another
board_type field describing card type (SFP/XFP/CX4).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_RCV_CTX was set to 1, there's only rx context per
PCI function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend copyright into 2009 and update address.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bail out if pci_map_single() fails while replenishing rx ring.
o Drop packet if pci_map_{single,page}() fail in tx.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix order or rom register writes.
o Reduce udelays when writing rom registers.
This cuts the firmware init time by 40%.
o Do not reset core/memory clocks when reinitializing driver.
Firmware willl handle this when initialized.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set restricted (little endian) data types in firmware command
requests and responses.
o Remove unnecessary conversion to LE when writing registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
NX3031 does not require driver to kill dma watchdog.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, multicast filtering, promisc mode, and max frame size
setting is handled by firmware, driver needs to send request to
enable/disable it.
For old chip revisions / firmware, driver still sets it directly.
Added function pointer to set mtu according to chip revision.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.
This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It had only couple of functions which are moved to main.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add macros for new chip revision and board configurations.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Don't count rx dropped packets based on return value of netif_receive_skb(),
which is misleading.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o eliminate tx lock in netxen adapter struct, instead pound on netdev
tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
reacquires tx lock in hard_xmit_frame(), this is already serialized
the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
different section of the ring than transmitting cpus and is
guarded by producer and consumer indices. This fixes a race
caused by rx softirq preemption on realtime kernels.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o separate and simpler irq handler for msi interrupts, avoids few checks
than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
and napi, which can uncork irq based on racy (lockless) access to tx
and rx ring indices. If we get interrupt, there's sufficient reason to
schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
that prevents posting rx desc to card. This improves performance in
low memory.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.
The driver will be able to deal with older firmware as well.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Here's the reworked patch.
This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.
This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().
This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resending patch 3/3 only.
These changes allow driver close routine to be called during module unload,
to clean-up buffers and other software resources, flush queues etc. Also,
hardware is reset to pristine state.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the various access routines to access different
control and status settings present in different register locations.
This will fix problems related to working of different ports in
multi Port card.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Add NETXEN prefixes to macros to clean them up.
This is a cleanup patch which adds NETXEN prefix to some stand
alone macro names.
These posed compile errors when NetXen driver was backported to 2.6.9
on PPC architecture as macros like USER_START are defined in file
arch/ppc64/mm/hash_utils.c
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Acked-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix PPC architecture specific bugs
Fixes some issues seen on Big endian machines.
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Port Swap feature
This patch will allow a port numbers on the card to be swapped in
host driver. This feature is applicable to cards having more than
1 port.
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix the multi PCI function for cards with more than 2 ports.
This patch fixes the working of multi PCI capable driver on cards with
more than 2 ports by adding the addresses for their rings and sizes.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Removal of redundant function call parameters and bug fixes.
This patch will remove the redundant paramters which were being passed to
many functions since now adapter->portnum can be used.
Signed-off-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Make driver use multiple PCI functions.
This patch will make NetXen driver work with multiple PCI functions. This will
make the usage of memory resources as well as interrupts more independent
among different functions which results in better throughput. This change has
been done after the multiport support is added in firmware.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetXen: This will fix a softlock seen on some machines.
The reason was too much time was spent waiting for hardware access
to go through.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Compiler warning spots real error!
The function do_rom_fast_read called in do_rom_fast_write can fail
and leave data1 unset. This causes a compile warning.
The correct thing is to propagate the error out.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Added ethtool support for user level firmware management utilities.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (42 commits)
r8169: extraneous Cmd{Tx/Rx}Enb write
forcedeth: modified comment header
NetXen: Reducing ring sizes for IOMMU issue.
NetXen: Fix for PPC machines.
NetXen: work queue fixes.
NetXen: Link status message correction for quad port cards.
NetXen: Multiple adapter fix.
NetXen: Using correct CHECKSUM flag.
NetXen: driver reload fix for newer firmware.
NetXen: Adding new device ids.
PHY probe not working properly for ibm_emac (PPC4xx)
ep93xx: some minor cleanups to the ep93xx eth driver
sky2: phy power down needs PCI config write enabled
sky2: power management/MSI workaround
sky2: dual port NAPI problem
via-velocity uses INET interfaces
e1000: Do not truncate TSO TCP header with 82544 workaround
myri10ge: handle failures in suspend and resume
myri10ge: no need to save MSI and PCIe state in the driver
myri10ge: make msi configurable at runtime through sysfs
...
The netxen driver includes a private ioctl that provides access
to functionality that is already available in other ways. The PCI
layer has application access hooks (see setpci), and the statistics
are available in ethtool/netstats.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
