It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a Setup packet is received but yet to DMA out, the controller will
not process the End Transfer command of any endpoint. Polling of its
DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
command timeout.
This may occur if the driver doesn’t service the completion interrupt of
the control status stage yet due to system latency, then it won’t
prepare TRB and start the transfer for the next Setup Stage. To the host
side, the control transfer had completed, and the host can send a new
Setup packet at this point.
In the meanwhile, if the driver receives an async call to dequeue a
request (triggering End Transfer) to any endpoint, then the driver will
service that End transfer first, blocking the control status stage
completion handler. Since no TRB is available for the Setup stage, the
Setup packet can’t be DMA’ed out and the End Transfer gets hung.
The driver must not block setting up of the Setup stage. So track and
only issue the End Transfer command only when there’s Setup TRB prepared
so that the controller can DMA out the Setup packet. Delay the End
transfer command if there's no Setup TRB available. This is applicable to
all DWC_usb3x IPs.
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220309205402.4467-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To improve reading the code this patch moves the cases to start_isoc or
return the function under one common condition check.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220306211251.2281335-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the PCI device ID and update the dwc3_pci_id_table
for Intel Alder Lake SoC.
The DWC3 controllor in the CPU block handles the USB3 traffic
and the device ID is common across the Alder Lake platforms.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20220308170848.30722-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver will schedule isoc transfers immediately on the
next interval, which is quite aggressive when the interval is 125us.
There's report that some platforms may need more time to process the
transfer, otherwise the controller may miss the first interval. Let's
keep it simple and give the controller at least 500us to schedule the
isoc transfer.
Link: https://lore.kernel.org/linux-usb/20220302143539.GI11577@pengutronix.de/
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/deb8146b8e1f7f8495ef2d5647017270934cb2d8.1646708142.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the 3.0 device core, if the core is programmed to operate in
2.0 only, then setting the GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK makes
the internal 2.0(utmi/ulpi) clock to be routed as the 3.0 (pipe)
clock. Enabling this feature allows the pipe3 clock to be not-running
when forcibly operating in 2.0 device mode.
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Bin Yang <yangbin@rock-chips.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220228135700.1089526-6-pgwipeout@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX8MP glue layer has support for the following flags:
* over-current polarity
* PWR pad polarity
* controlling PPC flag in HCCPARAMS register
* permanent port attach for usb2 & usb3 port
Allow setting these flags by supporting specific flags in the glue node.
In order to get this to work an additional IORESOURCE_MEM and clock is
necessary. For backward compatibility this is purely optional.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220218152707.2198357-4-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now the iomem used is not USB glue as the name suggests, but
HSIO BLK_CTL. Rename the struct member accordingly. This is a preparing
patch for when USB glue is actually used.
Reviewed-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220218152707.2198357-2-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify the drvdata structs. This also matches the definition of
member drvdata in dwc3_meson_g12a.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a3c178c9-7c33-d7b8-9f6e-734dc28728ab@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the phy driver to be able to actually get and control
the cs and reset GPIOs the dev_id member of the gpiod_lookup table must
be set to point to the dev_name() of the ulpi-device instantiated by
dwc3_ulpi_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-6-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on the TUSB1211 phy
for charger-detection.
Windows tablets with the same SoC + PMIC often use an extra chip for
charger-detection like the FSA831A. But since on Android tablets
the designers already need to add a TUSB1211 phy to support device/gadget
mode the phy is used to do charger-detection instead.
These Android x86 tablets can be identified by the unique combination of
a Bay Trail SoC (already checked for by PCI-ids) + a Crystal Cove PMIC +
not using the standard ACPI battery and ac drivers. Where as on Windows
tablets the standard ACPI battery and ac drivers will be used on BYT
boards with a Crystal Cove PMIC.
Set a special kernel-internal (so not part of the dt-bindings)
"linux,phy_charger_detect" property on these boards, which tells the
tusb1210 driver to enable charger-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk handling may need to set some different properties
which means using a different swnode, move the setting of the swnode
to inside dwc3_pci_quirks() so that the quirk handling can choose
a different swnode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_OF maybe set, but it may not be applicable to a device. In
such case, checking against that can cause the device fail to
initialize. Check against the device node (device->of_node) instead.
Fixes: a102f07e4e ("usb: dwc3: drd: Add support for usb-conn-gpio based usb-role-switch")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f15580ad5810b1e5f31c241b35ebedfbfc30a3f.1644964864.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.
Commit e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.
But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[ 28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[ 28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUCTL.REFCLKPER can only account for clock frequencies with integer
periods. To address this, program REFCLK_FLADJ with the relative error
caused by period truncation. The formula given in the register reference
has been rearranged to allow calculation based on rate (instead of
period), and to allow for fixed-point arithmetic.
Additionally, calculate a value for 240MHZDECR. This configures a
simulated 240Mhz clock using a counter with one fractional bit (PLS1).
This register is programmed only for versions >= 2.50a, since this is
the check also used by commit db2be4e9e3 ("usb: dwc3: Add frame length
adjustment quirk").
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-5-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a special property to determine the reference clock
period, use the rate of the reference clock. When we have a legacy
snps,ref-clock-period-ns property and no reference clock, use it
instead. Fractional clocks are not currently supported, and will be
dealt with in the next commit.
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-4-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of grabbing all clocks in bulk, grab them individually. This will
allow us to get the frequency or otherwise deal with discrete clocks. This
may break some platforms if they use a clock which doesn't use one of the
documented names.
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch to skip part of the initialization when a USB3 PHY was
not present could result in the return value being uninitialized in that
case, causing spurious probe failures. Initialize ret to 0 to avoid this.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220127221500.177021-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-conn-gpio devices are a subnode of the USB interface controller, which
needs to be populated.
This allows having a non-type-c connector providing dual-role.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220105071407.2240302-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the acpi_create_platform_device() function may return error
pointers, dwc3_qcom_create_urs_usb_platdev() function may return error
pointers too. Using IS_ERR_OR_NULL() to check the return value to fix this.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211222111823.22887-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_device_put() before return from
dwc3_qcom_acpi_register_core in the error handling case.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211231113641.31474-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop unneeded calls to platform_get_resource_byname() from
dwc3_host_init(). dwc3_host_init() already calls dwc3_host_get_irq()
which gets the irq number, just use this to get the IRQ resource data
and fill the xhci_resources[1]
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys introduced a new enhancement to DWC_usb32 called Multi-Stream
Transfer (MST) to improve bulk streams performance for SuperSpeed and
SuperSpeed Plus. This enhancement allows the controller to look ahead
and process multiple bulk streams.
Previously, to initiate a bulk stream transfer, the driver has to issue
Start Transfer command and wait for the stream to complete before
initiating a new stream. As a result, the controller does not process
TRBs beyond a single stream. With the enhancement, as long as there are
new requests, the dwc3 driver can keep preparing new TRBs and the
controller can keep caching and processing them without waiting for the
transfer completion.
The programming flow is similar to regular bulk endpoint with a few
additional rules:
1) Chained TRBs of the same stream must have a matching stream ID
2) The last TRB of a stream must have CHN=0
3) All the TRBs with LST=0 must have CSP=1
Depends on the application and usage, internal tests show significant
performance improvement in UASP transfers with this enhancement.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cd9c7a8bf11f790983ac546222dd114893f16b3a.1638242424.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cefdd52fa0.
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver knows what it needs to set for GEVNTSIZn, and the controller
doesn't modify this register unless there's a hard reset. To save a few
microseconds of register read in read-modify-write operation, simply do
register write with the expected values. This can improve performance
when there are many interrupts generated, which the driver needs to
check and handle.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/efddf4ee5821c4bc5ae7ad90d629ec7a0ebcbf9a.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller doesn't check for Update Transfer command parameters
DEPCMDPAR{0,1,2}. Writing to these registers is unnecessary. Ignoring
this improves performance slightly by removing the register write
delay.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/997d9ebf38c6bba920d4ee77bd8c77bf81978a55.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're not setting CMDACT (from "No Response" Update Transfer
command), then there's no point in checking for the command status. So
skip it. This can reduce a register read delay and improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3dc31cf11581ae3ee82d9202dda3fc17d897d786.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in case of a PCI dwc3 controller, leave the default DMA
mask. Calling of a 64 bit DMA mask breaks the driver on
cherrytrail based tablets like Cyberbook T116.
Fixes: 45d39448b4 ("usb: dwc3: support 64 bit DMA in platform driver")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hans De Goede <hdegoede@redhat.com>
Tested-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/20211113142959.27191-1-fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the endpoint interrupt functions
dwc3_gadget_endpoint_transfer_in_progress() and
dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint
descriptor. But it could be cleared in __dwc3_gadget_ep_disable()
when accessory disconnected. So we need to check whether it is null
or not before dereferencing it.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The End Transfer command from a stream endpoint will generate a NoStream
event, and we should ignore it. Currently we set the flag
DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command,
and it will be cleared on the next stream event. However, a stream event
may be generated before the End Transfer command completion and
prematurely clear the flag. Fix this by setting the flag on End Transfer
completion instead.
Fixes: 140ca4cfea ("usb: dwc3: gadget: Handle stream transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During our predesign phase for DWC_usb32, the GHWPARAMS9 register offset
was 0xc680. We revised our final design, and the GHWPARAMS9 offset is
now moved to 0xc6e8 on release.
Fixes: 16710380d3 ("usb: dwc3: Capture new capability register GHWPARAMS9")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1541737108266a97208ff827805be1f32852590c.1635202893.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
reset_control_(de)assert() calls are called on a shared reset line when
reset_control_reset has been used. This is not allowed by the reset
framework.
Use reset_control_rearm() call in suspend() and remove() as a way to state
that the resource is no longer used, hence the shared reset line
may be triggered again by other devices. Use reset_control_rearm() also in
case probe fails after reset() has been called.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should be
balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211112162827.128319-3-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the DWC3_EP_* flag macros so that the definitions are all
lined up on the same tab column for consistent style.
No functional change.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20211021180129.27938-2-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions may dynamically enable and disable their endpoints
regularly throughout their operation, particularly when Set Interface
is employed to switch between Alternate Settings. For instance the
UAC2 function has its respective endpoints for playback & capture
associated with AltSetting 1, in which case those endpoints would not
get enabled until the host activates the AltSetting. And they
conversely become disabled when the interfaces' AltSetting 0 is
chosen.
With the DWC3 FIFO resizing algorithm recently added, every
usb_ep_enable() call results in a call to resize that EP's TXFIFO,
but if the same endpoint is enabled again and again, this incorrectly
leads to FIFO RAM allocation exhaustion as the mechanism did not
account for the possibility that endpoints can be re-enabled many
times.
Example log splat:
dwc3 a600000.dwc3: Fifosize(3717) > RAM size(3462) ep3in depth:217973127
configfs-gadget gadget: u_audio_start_capture:521 Error!
dwc3 a600000.dwc3: request 000000000be13e18 was not queued to ep3in
Add another bit DWC3_EP_TXFIFO_RESIZED to dep->flags to keep track of
whether an EP had already been resized in the current configuration.
If so, bail out of dwc3_gadget_resize_tx_fifos() to avoid the
calculation error resulting from accumulating the EP's FIFO depth
repeatedly. This flag is retained across multiple ep_disable() and
ep_enable() calls and is cleared when GTXFIFOSIZn is reset in
dwc3_gadget_clear_tx_fifos() upon receiving the next Set Config.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20211021180129.27938-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since function drivers will still be active until dwc3_disconnect_gadget()
is called, some applications will continue to queue packets to DWC3
gadget. This can lead to a flood of messages regarding failed ep queue,
as the endpoint is in the process of being disabled. Change the log
level to debug, so that it can be enabled when debugging issues.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20211018192647.32121-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>