According to SP800-90B, two health failures are allowed: the intermittend
and the permanent failure. So far, only the intermittent failure was
implemented. The permanent failure was achieved by resetting the entire
entropy source including its health test state and waiting for two or
more back-to-back health errors.
This approach is appropriate for RCT, but not for APT as APT has a
non-linear cutoff value. Thus, this patch implements 2 cutoff values
for both RCT/APT. This implies that the health state is left untouched
when an intermittent failure occurs. The noise source is reset
and a new APT powerup-self test is performed. Yet, whith the unchanged
health test state, the counting of failures continues until a permanent
failure is reached.
Any non-failing raw entropy value causes the health tests to reset.
The intermittent error has an unchanged significance level of 2^-30.
The permanent error has a significance level of 2^-60. Considering that
this level also indicates a false-positive rate (see SP800-90B section 4.2)
a false-positive must only be incurred with a low probability when
considering a fleet of Linux kernels as a whole. Hitting the permanent
error may cause a panic(), the following calculation applies: Assuming
that a fleet of 10^9 Linux kernels run concurrently with this patch in
FIPS mode and on each kernel 2 health tests are performed every minute
for one year, the chances of a false positive is about 1:1000
based on the binomial distribution.
In addition, any power-up health test errors triggered with
jent_entropy_init are treated as permanent errors.
A permanent failure causes the entire entropy source to permanently
return an error. This implies that a caller can only remedy the situation
by re-allocating a new instance of the Jitter RNG. In a subsequent
patch, a transparent re-allocation will be provided which also changes
the implied heuristic entropy assessment.
In addition, when the kernel is booted with fips=1, the Jitter RNG
is defined to be part of a FIPS module. The permanent error of the
Jitter RNG is translated as a FIPS module error. In this case, the entire
FIPS module must cease operation. This is implemented in the kernel by
invoking panic().
The patch also fixes an off-by-one in the RCT cutoff value which is now
set to 30 instead of 31. This is because the counting of the values
starts with 0.
Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The jitterentropy's Repetition Count Test (RCT) as well as the Adaptive
Proportion Test (APT) are run unconditionally on any collected samples.
However, their result, i.e. ->health_failure, will only get checked if
fips_enabled is set, c.f. the jent_health_failure() wrapper.
I would argue that a RCT or APT failure indicates that something's
seriously off and that this should always be reported as an error,
independently of whether FIPS mode is enabled or not: it should be up to
callers whether or not and how to handle jitterentropy failures.
Make jent_health_failure() to unconditionally return ->health_failure,
independent of whether fips_enabled is set.
Note that fips_enabled isn't accessed from the jitterentropy code anymore
now. Remove the linux/fips.h include as well as the jent_fips_enabled()
wrapper.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The header file algapi.h includes skbuff.h unnecessarily since
all we need is a forward declaration for struct sk_buff. This
patch removes that inclusion.
Unfortunately skbuff.h pulls in a lot of things and drivers over
the years have come to rely on it so this patch adds a lot of
missing inclusions that result from this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SP800-90B specifies various requirements for the noise source(s) that
may seed any DRNG including SP800-90A DRBGs. In November 2020,
SP800-90B will be mandated for all noise sources that provide entropy
to DRBGs as part of a FIPS 140-[2|3] validation or other evaluation
types. Without SP800-90B compliance, a noise source is defined to always
deliver zero bits of entropy.
This patch ports the SP800-90B compliance from the user space Jitter RNG
version 2.2.0.
The following changes are applied:
- addition of (an enhanced version of) the repetitive count test (RCT)
from SP800-90B section 4.4.1 - the enhancement is due to the fact of
using the stuck test as input to the RCT.
- addition of the adaptive proportion test (APT) from SP800-90B section
4.4.2
- update of the power-on self test to perform a test measurement of 1024
noise samples compliant to SP800-90B section 4.3
- remove of the continuous random number generator test which is
replaced by APT and RCT
Health test failures due to the SP800-90B operation are only enforced in
FIPS mode. If a runtime health test failure is detected, the Jitter RNG
is reset. If more than 1024 resets in a row are performed, a permanent
error is returned to the caller.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the following build warnings by adding a header for
the definitions shared between jitterentropy.c and
jitterentropy-kcapi.c. Fixes the following:
crypto/jitterentropy.c:445:5: warning: symbol 'jent_read_entropy' was not declared. Should it be static?
crypto/jitterentropy.c:475:18: warning: symbol 'jent_entropy_collector_alloc' was not declared. Should it be static?
crypto/jitterentropy.c:509:6: warning: symbol 'jent_entropy_collector_free' was not declared. Should it be static?
crypto/jitterentropy.c:516:5: warning: symbol 'jent_entropy_init' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:59:6: warning: symbol 'jent_zalloc' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:64:6: warning: symbol 'jent_zfree' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:69:5: warning: symbol 'jent_fips_enabled' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:74:6: warning: symbol 'jent_panic' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:79:6: warning: symbol 'jent_memcpy' was not declared. Should it be static?
crypto/jitterentropy-kcapi.c:93:6: warning: symbol 'jent_get_nstime' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Stephan Mueller <smueller@chronox.de
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Jitter RNG implementation is updated to comply with upstream version
2.1.2. The change covers the following aspects:
* Time variation measurement is conducted over the LFSR operation
instead of the XOR folding
* Invcation of stuck test during initialization
* Removal of the stirring functionality and the Von-Neumann
unbiaser as the LFSR using a primitive and irreducible polynomial
generates an identical distribution of random bits
This implementation was successfully used in FIPS 140-2 validations
as well as in German BSI evaluations.
This kernel implementation was tested as follows:
* The unchanged kernel code file jitterentropy.c is compiled as part
of user space application to generate raw unconditioned noise
data. That data is processed with the NIST SP800-90B non-IID test
tool to verify that the kernel code exhibits an equal amount of noise
as the upstream Jitter RNG version 2.1.2.
* Using AF_ALG with the libkcapi tool of kcapi-rng the Jitter RNG was
output tested with dieharder to verify that the output does not
exhibit statistical weaknesses. The following command was used:
kcapi-rng -n "jitterentropy_rng" -b 100000000000 | dieharder -a -g 200
* The unchanged kernel code file jitterentropy.c is compiled as part
of user space application to test the LFSR implementation. The
LFSR is injected a monotonically increasing counter as input and
the output is fed into dieharder to verify that the LFSR operation
does not exhibit statistical weaknesses.
* The patch was tested on the Muen separation kernel which returns
a more coarse time stamp to verify that the Jitter RNG does not cause
regressions with its initialization test considering that the Jitter
RNG depends on a high-resolution timer.
Tested-by: Reto Buerki <reet@codelabs.ch>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"jitterentropy_rng" doesn't have any other implementations, nor is it
tested by the crypto self-tests. So it was unnecessary to change it to
subsys_initcall. Also it depends on the main clocksource being
initialized, which may happen after subsys_initcall, causing this error:
jitterentropy: Initialization failed with host not compliant with requirements: 2
Change it back to module_init().
Fixes: c4741b2305 ("crypto: run initcalls for generic implementations earlier")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use subsys_initcall for registration of all templates and generic
algorithm implementations, rather than module_init. Then change
cryptomgr to use arch_initcall, to place it before the subsys_initcalls.
This is needed so that when both a generic and optimized implementation
of an algorithm are built into the kernel (not loadable modules), the
generic implementation is registered before the optimized one.
Otherwise, the self-tests for the optimized implementation are unable to
allocate the generic implementation for the new comparison fuzz tests.
Note that on arm, a side effect of this change is that self-tests for
generic implementations may run before the unaligned access handler has
been installed. So, unaligned accesses will crash the kernel. This is
arguably a good thing as it makes it easier to detect that type of bug.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Drop duplicate header module.h from jitterentropy-kcapi.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As part of the Y2038 development, __getnstimeofday is not supposed to be
used any more. It is now replaced with ktime_get_ns. The Jitter RNG uses
the time stamp to measure the execution time of a given code path and
tries to detect variations in the execution time. Therefore, the only
requirement the Jitter RNG has, is a sufficient high resolution to
detect these variations.
The change was tested on x86 to show an identical behavior as RDTSC. The
used test code simply measures the execution time of the heart of the
RNG:
jent_get_nstime(&time);
jent_memaccess(ec, min);
jent_fold_time(NULL, time, &folded, min);
jent_get_nstime(&time2);
return ((time2 - time));
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The clocksource does not provide clocksource_register() function since
f893598 commit (clocksource: Mostly kill clocksource_register()), so
let's remove unnecessary information about this function from a comment.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since the API for jent_panic() does not include format string parameters,
adjust the call to panic() to use a literal string to avoid any future
callers from leaking format strings into the panic message.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The core of the Jitter RNG is intended to be compiled with -O0. To
ensure that the Jitter RNG can be compiled on all architectures,
separate out the RNG core into a stand-alone C file that can be compiled
with -O0 which does not depend on any kernel include file.
As no kernel includes can be used in the C file implementing the core
RNG, any dependencies on kernel code must be extracted.
A second file provides the link to the kernel and the kernel crypto API
that can be compiled with the regular compile options of the kernel.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
