commit 381c759d99 ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.
Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.
Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen_thread_worker() doesn't need to wait for kthread_stop(), it
can simply exit. Just pktgen_create_thread() and pg_net_exit() should
do get_task_struct()/put_task_struct(). kthread_stop(dead_thread) is
fine.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen_thread_worker() is obviously racy, kthread_stop() can come
between the kthread_should_stop() check and set_current_state().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the call skb_defer_rx_timestamp will first
check for a phydev before going in and manipulating the skb->data and
skb->len values. By doing this we can avoid unnecessary work on network
devices that don't support phydev. As a result we reduce the total
instruction count needed to process this on most devices.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Gunthorpe reported that since commit c02db8c629 ("rtnetlink: make
SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes
anymore with respect to their policy, that is, ifla_vfinfo_policy[].
Before, they were part of ifla_policy[], but they have been nested since
placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO,
which is another nested attribute for the actual VF attributes such as
IFLA_VF_MAC, IFLA_VF_VLAN, etc.
Despite the policy being split out from ifla_policy[] in this commit,
it's never applied anywhere. nla_for_each_nested() only does basic nla_ok()
testing for struct nlattr, but it doesn't know about the data context and
their requirements.
Fix, on top of Jason's initial work, does 1) parsing of the attributes
with the right policy, and 2) using the resulting parsed attribute table
from 1) instead of the nla_for_each_nested() loop (just like we used to
do when still part of ifla_policy[]).
Reference: http://thread.gmane.org/gmane.linux.network/368913
Fixes: c02db8c629 ("rtnetlink: make SR-IOV VF interface symmetric")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rony Efraim <ronye@mellanox.com>
Cc: Vlad Zolotarov <vladz@cloudius-systems.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1622baf54.
The side effect of this commit is to add a '@NONE' after each virtual
interface name with a 'ip link'. It may break existing scripts.
Reported-by: Olivier Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can crash kernel with
ip link add ifb10 numtxqueues 100000 type ifb
We must replace a BUG_ON() by proper test and return -EINVAL for
crazy values.
Fixes: 60877a32bc ("net: allow large number of tx queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rate estimators are limited to 4 Mpps, which was fine years ago, but
too small with current hardware generation.
Lets use 2^5 scaling instead of 2^10 to get 128 Mpps new limit.
On 64bit arch, use an "unsigned long" for temp storage and remove limit.
(We do not expect 32bit arches to be able to reach this point)
Tested:
tc -s -d filter sh dev eth0 parent ffff:
filter protocol ip pref 1 u32
filter protocol ip pref 1 u32 fh 800: ht divisor 1
filter protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:15
match 07000000/ff000000 at 12
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 166 sec
Action statistics:
Sent 39734251496 bytes 863788076 pkt (dropped 863788117, overlimits 0 requeues 0)
rate 4067Mbit 11053596pps backlog 0b 0p requeues 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_bstats_update_cpu() and other helpers were added to support
percpu stats for qdisc.
We want to add percpu stats for tc action, so this patch add common
helpers.
qdisc_bstats_update_cpu() is renamed to qdisc_bstats_cpu_update()
qdisc_qstats_drop_cpu() is renamed to qdisc_qstats_cpu_drop()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel sockets do not hold a reference for the network namespace to
which they point. Socket destruction broadcasting relies on the
network namespace and will cause the splat below when a kernel socket
is destroyed.
This fix simply ignores kernel sockets when they are destroyed.
Reported as:
general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU: 1 PID: 9130 Comm: kworker/1:1 Not tainted 4.1.0-gelk-debug+ #1
Workqueue: sock_diag_events sock_diag_broadcast_destroy_work
Stack:
ffff8800b9c586c0 ffff8800b9c586c0 ffff8800ac4692c0 ffff8800936d4a90
ffff8800352efd38 ffffffff8469a93e ffff8800352efd98 ffffffffc09b9b90
ffff8800352efd78 ffff8800ac4692c0 ffff8800b9c586c0 ffff8800831b6ab8
Call Trace:
[<ffffffff8469a93e>] ? mutex_unlock+0xe/0x10
[<ffffffffc09b9b90>] ? inet_diag_handler_get_info+0x110/0x1fb [inet_diag]
[<ffffffff845c868d>] netlink_broadcast+0x1d/0x20
[<ffffffff8469a93e>] ? mutex_unlock+0xe/0x10
[<ffffffff845b2bf5>] sock_diag_broadcast_destroy_work+0xd5/0x160
[<ffffffff8408ea97>] process_one_work+0x147/0x420
[<ffffffff8408f0f9>] worker_thread+0x69/0x470
[<ffffffff8409fda3>] ? preempt_count_sub+0xa3/0xf0
[<ffffffff8408f090>] ? rescuer_thread+0x320/0x320
[<ffffffff84093cd7>] kthread+0x107/0x120
[<ffffffff84093bd0>] ? kthread_create_on_node+0x1b0/0x1b0
[<ffffffff8469d31f>] ret_from_fork+0x3f/0x70
[<ffffffff84093bd0>] ? kthread_create_on_node+0x1b0/0x1b0
Tested:
Using a debug kernel while 'ss -E' is running:
ip netns add test-ns
ip netns delete test-ns
Fixes: eb4cb00852 sock_diag: define destruction multicast groups
Fixes: 26abe14379 net: Modify sk_alloc to not reference count the
netns of kernel sockets.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/flow_dissector.c: In function ‘__skb_flow_dissect’:
net/core/flow_dissector.c:132: warning: ‘ip_proto’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"A rather largish update for everything time and timer related:
- Cache footprint optimizations for both hrtimers and timer wheel
- Lower the NOHZ impact on systems which have NOHZ or timer migration
disabled at runtime.
- Optimize run time overhead of hrtimer interrupt by making the clock
offset updates smarter
- hrtimer cleanups and removal of restrictions to tackle some
problems in sched/perf
- Some more leap second tweaks
- Another round of changes addressing the 2038 problem
- First step to change the internals of clock event devices by
introducing the necessary infrastructure
- Allow constant folding for usecs/msecs_to_jiffies()
- The usual pile of clockevent/clocksource driver updates
The hrtimer changes contain updates to sched, perf and x86 as they
depend on them plus changes all over the tree to cleanup API changes
and redundant code, which got copied all over the place. The y2038
changes touch s390 to remove the last non 2038 safe code related to
boot/persistant clock"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
clocksource: Increase dependencies of timer-stm32 to limit build wreckage
timer: Minimize nohz off overhead
timer: Reduce timer migration overhead if disabled
timer: Stats: Simplify the flags handling
timer: Replace timer base by a cpu index
timer: Use hlist for the timer wheel hash buckets
timer: Remove FIFO "guarantee"
timers: Sanitize catchup_timer_jiffies() usage
hrtimer: Allow hrtimer::function() to free the timer
seqcount: Introduce raw_write_seqcount_barrier()
seqcount: Rename write_seqcount_barrier()
hrtimer: Fix hrtimer_is_queued() hole
hrtimer: Remove HRTIMER_STATE_MIGRATE
selftest: Timers: Avoid signal deadlock in leap-a-day
timekeeping: Copy the shadow-timekeeper over the real timekeeper last
clockevents: Check state instead of mode in suspend/resume path
selftests: timers: Add leap-second timer edge testing to leap-a-day.c
ntp: Do leapsecond adjustment in adjtimex read path
time: Prevent early expiry of hrtimers[CLOCK_REALTIME] at the leap second edge
ntp: Introduce and use SECS_PER_DAY macro instead of 86400
...
The lockless lookups can return entry that is unlinked.
Sometimes they get reference before last neigh_cleanup_and_release,
sometimes they do not need reference. Later, any
modification attempts may result in the following problems:
1. entry is not destroyed immediately because neigh_update
can start the timer for dead entry, eg. on change to NUD_REACHABLE
state. As result, entry lives for some time but is invisible
and out of control.
2. __neigh_event_send can run in parallel with neigh_destroy
while refcnt=0 but if timer is started and expired refcnt can
reach 0 for second time leading to second neigh_destroy and
possible crash.
Thanks to Eric Dumazet and Ying Xue for their work and analyze
on the __neigh_event_send change.
Fixes: 767e97e1e0 ("neigh: RCU conversion of struct neighbour")
Fixes: a263b30936 ("ipv4: Make neigh lookups directly in output packet path.")
Fixes: 6fd6ce2056 ("ipv6: Do not depend on rt->n in ip6_finish_output2().")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing current->pid/uid from cls_bpf may lead to misleading results and
should not be used when TC classifiers need accurate information about pid/uid.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These groups will contain socket-destruction events for
AF_INET/AF_INET6, IPPROTO_TCP/IPPROTO_UDP.
Near the end of socket destruction, a check for listeners is
performed. In the presence of a listener, rather than completely
cleanup the socket, a unit of work will be added to a private
work queue which will first broadcast information about the socket
and then finish the cleanup operation.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_get_vf_stats where the PF retrieves and fills the VFs traffic
statistics. We encode the VF stats in a nested manner to allow for
future extensions.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_trace_printk() is a helper function used to debug eBPF programs.
Let socket and TC programs use it as well.
Note, it's DEBUG ONLY helper. If it's used in the program,
the kernel will print warning banner to make sure users don't use
it in production.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF programs attached to kprobes need to filter based on
current->pid, uid and other fields, so introduce helper functions:
u64 bpf_get_current_pid_tgid(void)
Return: current->tgid << 32 | current->pid
u64 bpf_get_current_uid_gid(void)
Return: current_gid << 32 | current_uid
bpf_get_current_comm(char *buf, int size_of_buf)
stores current->comm into buf
They can be used from the programs attached to TC as well to classify packets
based on current task fields.
Update tracex2 example to print histogram of write syscalls for each process
instead of aggregated for all.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__skb_header_pointer() returns a pointer that must be checked.
Fixes infinite loop reported by Alexei, and add __must_check to
catch these errors earlier.
Fixes: 6a74fcf426 ("flow_dissector: add support for dst, hop-by-hop and routing ext hdrs")
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Tested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dst, hop-by-hop or routing extension headers are present determine
length of the options and skip over them in flow dissection.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to shift after masking to get label value for comparison.
Fixes: b3baa0fbd0 ("mpls: Add MPLS entropy label in flow_keys")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We saw excessive direct memory compaction triggered by skb_page_frag_refill.
This causes performance issues and add latency. Commit 5640f76858
introduces the order-3 allocation. According to the changelog, the order-3
allocation isn't a must-have but to improve performance. But direct memory
compaction has high overhead. The benefit of order-3 allocation can't
compensate the overhead of direct memory compaction.
This patch makes the order-3 page allocation atomic. If there is no memory
pressure and memory isn't fragmented, the alloction will still success, so we
don't sacrifice the order-3 benefit here. If the atomic allocation fails,
direct memory compaction will not be triggered, skb_page_frag_refill will
fallback to order-0 immediately, hence the direct memory compaction overhead is
avoided. In the allocation failure case, kswapd is waken up and doing
compaction, so chances are allocation could success next time.
alloc_skb_with_frags is the same.
The mellanox driver does similar thing, if this is accepted, we must fix
the driver too.
V3: fix the same issue in alloc_skb_with_frags as pointed out by Eric
V2: make the changelog clearer
Cc: Eric Dumazet <edumazet@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Debabrata Banerjee <dbavatar@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add strings array of the current supported tunable options.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 70008aa50e ("skbuff: convert to skb_orphan_frags") replaced
open coded tests of SKBTX_DEV_ZEROCOPY and skb_copy_ubufs with calls
to helper function skb_orphan_frags. Apply that to the last remaining
open coded site.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eBPF programs attached to ingress and egress qdiscs see inconsistent skb->data.
For ingress L2 header is already pulled, whereas for egress it's present.
This is known to program writers which are currently forced to use
BPF_LL_OFF workaround.
Since programs don't change skb internal pointers it is safe to do
pull/push right around invocation of the program and earlier taps and
later pt->func() will not be affected.
Multiple taps via packet_rcv(), tpacket_rcv() are doing the same trick
around run_filter/BPF_PROG_RUN even if skb_shared.
This fix finally allows programs to use optimized LD_ABS/IND instructions
without BPF_LL_OFF for higher performance.
tc ingress + cls_bpf + samples/bpf/tcbpf1_kern.o
w/o JIT w/JIT
before 20.5 23.6 Mpps
after 21.8 26.6 Mpps
Old programs with BPF_LL_OFF will still work as-is.
We can now undo most of the earlier workaround commit:
a166151cbe ("bpf: fix bpf helpers to use skb->mac_header relative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow dissector if an MPLS header contains an entropy label this is
saved in the new keyid field of flow_keys. The entropy label is
then represented in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow dissector if a GRE header contains a keyid this is saved in the
new keyid field of flow_keys. The GRE keyid is then represented
in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow_dissector set the flow label in flow_keys for IPv6. This also
removes the shortcircuiting of flow dissection when a non-zero label
is present, the flow label can be considered to provide additional
entropy for a hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow_dissector set vlan_id in flow_keys when VLAN is found.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to return the IPv6 address hash as part of flow keys.
In general, using the IPv6 address hash is risky in a hash value
since the underlying use of xor provides no entropy. If someone
really needs the hash value they can get it from the full IPv6
addresses in flow keys (e.g. from flow_get_u32_src).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes flow hashing to use jhash2 over the flow_keys
structure instead just doing jhash_3words over src, dst, and ports.
This method will allow us take more input into the hashing function
so that we can include full IPv6 addresses, VLAN, flow labels etc.
without needing to resort to xor'ing which makes for a poor hash.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
key_basic is set twice in __skb_flow_dissect which seems unnecessary.
Remove second one.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do break when we see routing flag or a non-zero version number in GRE
header.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix build error:
net/core/filter.c: In function 'bpf_clone_redirect':
net/core/filter.c:1429:18: error: 'struct sk_buff' has no member named 'tc_verd'
if (G_TC_AT(skb2->tc_verd) & AT_INGRESS)
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we scan a packet for GRO processing, we want to see the most
common packet types in the front of the offload_base list.
So add a priority field so we can handle this properly.
IPv4/IPv6 get the highest priority with the implicit zero priority
field.
Next comes ethernet with a priority of 10, and then we have the MPLS
types with a priority of 15.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f96dee13b8.
It isn't right, ethtool is meant to manage one PHY instance
per netdevice at a time, and this is selected by the SET
command. Therefore by definition the GET command must only
return the settings for the configured and selected PHY.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this is already exported from tracing side via commit d9847d310a
("tracing: Allow BPF programs to call bpf_ktime_get_ns()"), we might
as well want to move it to the core, so also networking users can make
use of it, e.g. to measure diffs for certain flows from ingress/egress.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
classic BPF already exposes skb->dev->ifindex via SKF_AD_IFINDEX extension.
Allow eBPF program to access it as well. Note that classic aborts execution
of the program if 'skb->dev == NULL' (which is inconvenient for program
writers), whereas eBPF returns zero in such case.
Also expose the 'skb_iif' field, since programs triggered by redirected
packet need to known the original interface index.
Summary:
__skb->ifindex -> skb->dev->ifindex
__skb->ingress_ifindex -> skb->skb_iif
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.
We can then revert 843925f33f
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF=-D__CHECK_ENDIAN__ net/core/utils.o
...
net/core/utils.c:307:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:307:72: expected restricted __wsum [usertype] addend
net/core/utils.c:307:72: got restricted __be32 [usertype] from
net/core/utils.c:308:34: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:308:34: expected restricted __wsum [usertype] addend
net/core/utils.c:308:34: got restricted __be32 [usertype] to
net/core/utils.c:310:70: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:70: expected restricted __wsum [usertype] addend
net/core/utils.c:310:70: got restricted __be32 [usertype] from
net/core/utils.c:310:77: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:77: expected restricted __wsum [usertype] addend
net/core/utils.c:310:77: got restricted __be32 [usertype] to
net/core/utils.c:312:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:312:72: expected restricted __wsum [usertype] addend
net/core/utils.c:312:72: got restricted __be32 [usertype] from
net/core/utils.c:313:35: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:313:35: expected restricted __wsum [usertype] addend
net/core/utils.c:313:35: got restricted __be32 [usertype] to
Note we can use csum_replace4() helper
Fixes: 58e3cac561 ("net: optimise inet_proto_csum_replace4()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make C=2 CF=-D__CHECK_ENDIAN__ net/core/secure_seq.o
net/core/secure_seq.c:157:50: warning: restricted __be32 degrades to
integer
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/pktgen.c:2672:43: warning: incorrect type in assignment (different base types)
net/core/pktgen.c:2672:43: expected unsigned short [unsigned] [short] [usertype] <noident>
net/core/pktgen.c:2672:43: got restricted __be16 [usertype] protocol
Let's use proper struct ethhdr instead of hard coding everything.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_stream_recvmsg is refactored to unix_stream_read_generic in this
patch and enhanced to deal with pipe splicing. The refactoring is
inneglible, we mostly have to deal with a non-existing struct msghdr
argument.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare skb_splice_bits to be able to deal with AF_UNIX sockets.
AF_UNIX sockets don't use lock_sock/release_sock and thus we have to
use a callback to make the locking and unlocking configureable.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Giving /proc/net/pktgen/pgctrl an invalid command just returns shell
success and prints a warning in dmesg. This is not very useful for
shell scripting, as it can only detect the error by parsing dmesg.
Instead return -EINVAL when the command is unknown, as this provides
userspace shell scripting a way of detecting this.
Also bump version tag to 2.75, because (1) reading /proc/net/pktgen/pgctrl
output this version number which would allow to detect this small
semantic change, and (2) because the pktgen version tag have not been
updated since 2010.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many spaces were introduced in commit 63adc6fb8a ("pktgen: cleanup
checkpatch warnings"), thus misaligning "src_min:" to other columns.
Fixes: 63adc6fb8a ("pktgen: cleanup checkpatch warnings")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restored previous behaviour. If caller does not want ports to be
filled, we should not break.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce bpf_tail_call(ctx, &jmp_table, index) helper function
which can be used from BPF programs like:
int bpf_prog(struct pt_regs *ctx)
{
...
bpf_tail_call(ctx, &jmp_table, index);
...
}
that is roughly equivalent to:
int bpf_prog(struct pt_regs *ctx)
{
...
if (jmp_table[index])
return (*jmp_table[index])(ctx);
...
}
The important detail that it's not a normal call, but a tail call.
The kernel stack is precious, so this helper reuses the current
stack frame and jumps into another BPF program without adding
extra call frame.
It's trivially done in interpreter and a bit trickier in JITs.
In case of x64 JIT the bigger part of generated assembler prologue
is common for all programs, so it is simply skipped while jumping.
Other JITs can do similar prologue-skipping optimization or
do stack unwind before jumping into the next program.
bpf_tail_call() arguments:
ctx - context pointer
jmp_table - one of BPF_MAP_TYPE_PROG_ARRAY maps used as the jump table
index - index in the jump table
Since all BPF programs are idenitified by file descriptor, user space
need to populate the jmp_table with FDs of other BPF programs.
If jmp_table[index] is empty the bpf_tail_call() doesn't jump anywhere
and program execution continues as normal.
New BPF_MAP_TYPE_PROG_ARRAY map type is introduced so that user space can
populate this jmp_table array with FDs of other bpf programs.
Programs can share the same jmp_table array or use multiple jmp_tables.
The chain of tail calls can form unpredictable dynamic loops therefore
tail_call_cnt is used to limit the number of calls and currently is set to 32.
Use cases:
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
==========
- simplify complex programs by splitting them into a sequence of small programs
- dispatch routine
For tracing and future seccomp the program may be triggered on all system
calls, but processing of syscall arguments will be different. It's more
efficient to implement them as:
int syscall_entry(struct seccomp_data *ctx)
{
bpf_tail_call(ctx, &syscall_jmp_table, ctx->nr /* syscall number */);
... default: process unknown syscall ...
}
int sys_write_event(struct seccomp_data *ctx) {...}
int sys_read_event(struct seccomp_data *ctx) {...}
syscall_jmp_table[__NR_write] = sys_write_event;
syscall_jmp_table[__NR_read] = sys_read_event;
For networking the program may call into different parsers depending on
packet format, like:
int packet_parser(struct __sk_buff *skb)
{
... parse L2, L3 here ...
__u8 ipproto = load_byte(skb, ... offsetof(struct iphdr, protocol));
bpf_tail_call(skb, &ipproto_jmp_table, ipproto);
... default: process unknown protocol ...
}
int parse_tcp(struct __sk_buff *skb) {...}
int parse_udp(struct __sk_buff *skb) {...}
ipproto_jmp_table[IPPROTO_TCP] = parse_tcp;
ipproto_jmp_table[IPPROTO_UDP] = parse_udp;
- for TC use case, bpf_tail_call() allows to implement reclassify-like logic
- bpf_map_update_elem/delete calls into BPF_MAP_TYPE_PROG_ARRAY jump table
are atomic, so user space can build chains of BPF programs on the fly
Implementation details:
=======================
- high performance of bpf_tail_call() is the goal.
It could have been implemented without JIT changes as a wrapper on top of
BPF_PROG_RUN() macro, but with two downsides:
. all programs would have to pay performance penalty for this feature and
tail call itself would be slower, since mandatory stack unwind, return,
stack allocate would be done for every tailcall.
. tailcall would be limited to programs running preempt_disabled, since
generic 'void *ctx' doesn't have room for 'tail_call_cnt' and it would
need to be either global per_cpu variable accessed by helper and by wrapper
or global variable protected by locks.
In this implementation x64 JIT bypasses stack unwind and jumps into the
callee program after prologue.
- bpf_prog_array_compatible() ensures that prog_type of callee and caller
are the same and JITed/non-JITed flag is the same, since calling JITed
program from non-JITed is invalid, since stack frames are different.
Similarly calling kprobe type program from socket type program is invalid.
- jump table is implemented as BPF_MAP_TYPE_PROG_ARRAY to reuse 'map'
abstraction, its user space API and all of verifier logic.
It's in the existing arraymap.c file, since several functions are
shared with regular array map.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce ifdef pollution slightly, no functional change. We can simply
remove the extra alternative definition of handle_ing() and nf_ingress().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[1] When entering NUD_PROBE state via neigh_update(), perhaps received
from userspace, correctly (re)initialize the probes count to zero.
This is useful for forcing revalidation of a neighbor (for example
if the host is attempting to do DNA [IPv4 4436, IPv6 6059]).
[2] Notify listeners when a neighbor goes into NUD_PROBE state.
By sending notifications on entry to NUD_PROBE state listeners get
more timely warnings of imminent connectivity issues.
The current notifications on entry to NUD_STALE have somewhat
limited usefulness: NUD_STALE is a perfectly normal state, as is
NUD_DELAY, whereas notifications on entry to NUD_FAILURE come after
a neighbor reachability problem has been confirmed (typically after
three probes).
Signed-off-by: Erik Kline <ek@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is used to protect netns_ids which is per net,
so there is no need to use a global spinlock.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_mem_reclaim_partial() goal is to ensure each socket has
one SK_MEM_QUANTUM forward allocation. This is needed both for
performance and better handling of memory pressure situations in
follow up patches.
SK_MEM_QUANTUM is currently a page, but might be reduced to 4096 bytes
as some arches have 64KB pages.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, the command 'ip link add bond2 type bond mode 802.3ad'
causes the kernel to send a rtnl message for the bond2 interface, with an
ifindex 0.
'ip monitor' shows:
0: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 state DOWN group default
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond2@NONE: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default
link/ether ea:3e:1f:53:92:7b brd ff:ff:ff:ff:ff:ff
[snip]
The patch fixes the spotted bug by checking in bond driver if the interface
is registered before calling the notifier chain.
It also adds a check in rtmsg_ifinfo() to prevent this kind of bug in the
future.
Fixes: d4261e5650 ("bonding: create netlink event when bonding option is changed")
CC: Jiri Pirko <jiri@resnulli.us>
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d2788d3488 ("net: sched: further simplify handle_ing")
removed the call to qdisc_enqueue_root().
However, after this removal we no longer set qdisc pkt length.
This breaks traffic policing on ingress.
This is the minimum fix: set qdisc pkt length before tc_classify.
Only setting the length does remove support for 'stab' on ingress, but
as Alexei pointed out:
"Though it was allowed to add qdisc_size_table to ingress, it's useless.
Nothing takes advantage of recomputed qdisc_pkt_len".
Jamal suggested to use qdisc_pkt_len_init(), but as Eric mentioned that
would result in qdisc_pkt_len_init to no longer get inlined due to the
additional 2nd call site.
ingress policing is rare and GRO doesn't really work that well with police
on ingress, as we see packets > mtu and drop skbs that -- without
aggregation -- would still have fitted the policier budget.
Thus to have reliable/smooth ingress policing GRO has to be turned off.
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: d2788d3488 ("net: sched: further simplify handle_ing")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlock was missing on error path.
Fixes: 95f38411df ("netns: use a spin_lock to protect nsid management")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Netfilter ingress hook just after the existing tc ingress
hook, that seems to be the consensus solution for this.
Note that the Netfilter hook resides under the global static key that enables
ingress filtering. Nonetheless, Netfilter still also has its own static key for
minimal impact on the existing handle_ing().
* Without this patch:
Result: OK: 6216490(c6216338+d152) usec, 100000000 (60byte,0frags)
16086246pps 7721Mb/sec (7721398080bps) errors: 100000000
42.46% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
25.92% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
7.81% kpktgend_0 [pktgen] [k] pktgen_thread_worker
5.62% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.70% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
2.34% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
1.44% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* With this patch:
Result: OK: 6214833(c6214731+d101) usec, 100000000 (60byte,0frags)
16090536pps 7723Mb/sec (7723457280bps) errors: 100000000
41.23% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
26.57% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
7.72% kpktgend_0 [pktgen] [k] pktgen_thread_worker
5.55% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.78% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
2.06% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
1.43% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* Without this patch + tc ingress:
tc filter add dev eth4 parent ffff: protocol ip prio 1 \
u32 match ip dst 4.3.2.1/32
Result: OK: 9269001(c9268821+d179) usec, 100000000 (60byte,0frags)
10788648pps 5178Mb/sec (5178551040bps) errors: 100000000
40.99% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
17.50% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
11.77% kpktgend_0 [cls_u32] [k] u32_classify
5.62% kpktgend_0 [kernel.kallsyms] [k] tc_classify_compat
5.18% kpktgend_0 [pktgen] [k] pktgen_thread_worker
3.23% kpktgend_0 [kernel.kallsyms] [k] tc_classify
2.97% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
1.83% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
1.50% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
0.99% kpktgend_0 [kernel.kallsyms] [k] __build_skb
* With this patch + tc ingress:
tc filter add dev eth4 parent ffff: protocol ip prio 1 \
u32 match ip dst 4.3.2.1/32
Result: OK: 9308218(c9308091+d126) usec, 100000000 (60byte,0frags)
10743194pps 5156Mb/sec (5156733120bps) errors: 100000000
42.01% kpktgend_0 [kernel.kallsyms] [k] __netif_receive_skb_core
17.78% kpktgend_0 [kernel.kallsyms] [k] kfree_skb
11.70% kpktgend_0 [cls_u32] [k] u32_classify
5.46% kpktgend_0 [kernel.kallsyms] [k] tc_classify_compat
5.16% kpktgend_0 [pktgen] [k] pktgen_thread_worker
2.98% kpktgend_0 [kernel.kallsyms] [k] ip_rcv
2.84% kpktgend_0 [kernel.kallsyms] [k] tc_classify
1.96% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_internal
1.57% kpktgend_0 [kernel.kallsyms] [k] netif_receive_skb_sk
Note that the results are very similar before and after.
I can see gcc gets the code under the ingress static key out of the hot path.
Then, on that cold branch, it generates the code to accomodate the netfilter
ingress static key. My explanation for this is that this reduces the pressure
on the instruction cache for non-users as the new code is out of the hot path,
and it comes with minimal impact for tc ingress users.
Using gcc version 4.8.4 on:
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 8
[...]
L1d cache: 16K
L1i cache: 64K
L2 cache: 2048K
L3 cache: 8192K
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new config switch enables the ingress filtering infrastructure that is
controlled through the ingress_needed static key. This prepares the
introduction of the Netfilter ingress hook that resides under this unique
static key.
Note that CONFIG_SCH_INGRESS automatically selects this, that should be no
problem since this also depends on CONFIG_NET_CLS_ACT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I had inlined __alloc_rx_skb into __netdev_alloc_skb and
__napi_alloc_skb I had overlooked the fact that there was a return in the
__alloc_rx_skb. As a result we weren't reserving headroom or setting the
skb->dev in certain cases. This change corrects that by adding a couple of
jump labels to jump to depending on __alloc_skb either succeeding or failing.
Fixes: 9451980a66 ("net: Use cached copy of pfmemalloc to avoid accessing page")
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only hashes made out of ipv6 addresses could be dissected. This
patch introduces support for dissection of full ipv6 addresses.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce dissector infrastructure which allows user to specify which
parts of skb he wants to dissect.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
next to its user. No relation to flow_dissector so it makes no sense to
have it in flow_dissector.c
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
__skb_tx_hash function has no relation to flow_dissect so just move it
to dev.c
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these functions are defined in flow_dissector.c, move header
declarations from skbuff.h into flow_dissector.h
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older gcc versions (e.g. gcc version 4.4.6) don't like anonymous unions
which was causing build issues on the newly added switchdev attr/obj
structs. Fix this by using named union on structs.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pkt_gen->last_ok was not set properly, so after the first burst
pktgen instead of allocating new packet, will reuse old one, advance
eth_type_trans further, which would mean the stack will be seeing very
short bogus packets.
Fixes: 62f64aed62 ("pktgen: introduce xmit_mode '<start_xmit|netif_receive>'")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions compile to 60 bytes of machine code each.
With this .config: http://busybox.net/~vda/kernel_config
there are 617 calls of netif_tx_stop_queue()
and 49 calls of netif_tx_stop_all_queues() in vmlinux.
To fix this, remove WARN_ON in netif_tx_stop_queue()
as suggested by davem, and deinline netif_tx_stop_all_queues().
Change in code size is about 20k:
text data bss dec hex filename
82426986 22255416 20627456 125309858 77813a2 vmlinux.before
82406248 22255416 20627456 125289120 777c2a0 vmlinux
gcc-4.7.2 still creates deinlined version of netif_tx_stop_queue
sometimes:
$ nm --size-sort vmlinux | grep netif_tx_stop_queue | wc -l
190
ffffffff81b558a8 <netif_tx_stop_queue>:
ffffffff81b558a8: 55 push %rbp
ffffffff81b558a9: 48 89 e5 mov %rsp,%rbp
ffffffff81b558ac: f0 80 8f e0 01 00 00 lock orb $0x1,0x1e0(%rdi)
ffffffff81b558b3: 01
ffffffff81b558b4: 5d pop %rbp
ffffffff81b558b5: c3 retq
This needs additional fixing.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Alexei Starovoitov <alexei.starovoitov@gmail.com>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Joe Perches <joe@perches.com>
CC: David S. Miller <davem@davemloft.net>
CC: Jiri Pirko <jpirko@redhat.com>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: netfilter-devel@vger.kernel.org
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually, RTM_NEWxxx is returned on a get (same as a dump).
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa said remove the feature flag for this series and she'll work on
bringing it back if needed at a later date.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch ID is just a gettable port attribute. Convert switchdev op
switchdev_parent_id_get to a switchdev attr.
Note: for sysfs and netlink interfaces, SWITCHDEV_ATTR_PORT_PARENT_ID is
called with SWITCHDEV_F_NO_RECUSE to limit switch ID user-visiblity to only
port netdevs. So when a port is stacked under bond/bridge, the user can
only query switch id via the switch ports, but not via the upper devices
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a function called skb_free_frag which is meant to
compliment the function netdev_alloc_frag. The general idea is to enable a
more lightweight version of page freeing since we don't actually need all
the overhead of a put_page, and we don't quite fit the model of __free_pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves the __alloc_page_frag functionality out of the networking
stack and into the page allocation portion of mm. The idea it so help make
this maintainable by placing it with other page allocation functions.
Since we are moving it from skbuff.c to page_alloc.c I have also renamed
the basic defines and structure from netdev_alloc_cache to page_frag_cache
to reflect that this is now part of a different kernel subsystem.
I have also added a simple __free_page_frag function which can handle
freeing the frags based on the skb->head pointer. The model for this is
based off of __free_pages since we don't actually need to deal with all of
the cases that put_page handles. I incorporated the virt_to_head_page call
and compound_order into the function as it actually allows for a signficant
size reduction by reducing code duplication.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we store the virtual address of the page
in the netdev_alloc_cache instead of the page pointer. The idea behind
this is to avoid multiple calls to page_address since the virtual address
is required for every access, but the page pointer is only needed at
allocation or reset of the page.
While I was at it I also reordered the netdev_alloc_cache structure a bit
so that the size is always 16 bytes by dropping size in the case where
PAGE_SIZE is greater than or equal to 32KB.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing I found that the testing for pfmemalloc in build_skb was
rather expensive. I found the issue to be two-fold. First we have to get
from the virtual address to the head page and that comes at the cost of
something like 11 cycles. Then there is the cost for reading pfmemalloc out
of the head page which can be cache cold due to the fact that
put_page_testzero is likely invalidating the cache-line on one or more
CPUs as the fragments can be shared.
To avoid this extra expense I have added a pfmemalloc member to the
netdev_alloc_cache. I then pushed pieces of __alloc_rx_skb into
__napi_alloc_skb and __netdev_alloc_skb so that I could rewrite them to
make use of the cached pfmemalloc value. The result is that my perf traces
show a reduction from 9.28% overhead to 3.7% for the code covered by
build_skb, __alloc_rx_skb, and __napi_alloc_skb when performing a test with
the packet being dropped instead of being handed to napi_gro_receive.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingress qdisc has no other purpose than calling into tc_classify()
that executes attached classifier(s) and action(s).
It has a 1:1 relationship to dev->ingress_queue. After having commit
087c1a601a ("net: sched: run ingress qdisc without locks") removed
the central ingress lock, one major contention point is gone.
The extra indirection layers however, are not necessary for calling
into ingress qdisc. pktgen calling locally into netif_receive_skb()
with a dummy u32, single CPU result on a Supermicro X10SLM-F, Xeon
E3-1240: before ~21,1 Mpps, after patch ~22,9 Mpps.
We can redirect the private classifier list to the netdev directly,
without changing any classifier API bits (!) and execute on that from
handle_ing() side. The __QDISC_STATE_DEACTIVATE test can be removed,
ingress qdisc doesn't have a queue and thus dev_deactivate_queue()
is also not applicable, ingress_cl_list provides similar behaviour.
In other words, ingress qdisc acts like TCQ_F_BUILTIN qdisc.
One next possible step is the removal of the dev's ingress (dummy)
netdev_queue, and to only have the list member in the netdevice
itself.
Note, the filter chain is RCU protected and individual filter elements
are being kfree'd by sched subsystem after RCU grace period. RCU read
lock is being held by __netif_receive_skb_core().
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given quite some code has been removed from ing_filter(), we can just
consolidate that function into handle_ing() and get rid of a few
instructions at the same time.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are no longer needed and no longer used kill them.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sk_alloc knows when a kernel socket is being allocated modify
it to not reference count the network namespace of kernel sockets.
Keep track of if a socket needs reference counting by adding a flag to
struct sock called sk_net_refcnt.
Update all of the callers of sock_create_kern to stop using
sk_change_net and sk_release_kernel as those hacks are no longer
needed, to avoid reference counting a kernel socket.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changing how struct net is refcounted
on kernel sockets pass the knowledge that we are creating
a kernel socket from sock_create_kern through to sk_alloc.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xmit_mode 'netif_receive' for pktgen which generates the
packets using familiar pktgen commands, but feeds them into
netif_receive_skb() instead of ndo_start_xmit().
Default mode is called 'start_xmit'.
It is designed to test netif_receive_skb and ingress qdisc
performace only. Make sure to understand how it works before
using it for other rx benchmarking.
Sample script 'pktgen.sh':
\#!/bin/bash
function pgset() {
local result
echo $1 > $PGDEV
result=`cat $PGDEV | fgrep "Result: OK:"`
if [ "$result" = "" ]; then
cat $PGDEV | fgrep Result:
fi
}
[ -z "$1" ] && echo "Usage: $0 DEV" && exit 1
ETH=$1
PGDEV=/proc/net/pktgen/kpktgend_0
pgset "rem_device_all"
pgset "add_device $ETH"
PGDEV=/proc/net/pktgen/$ETH
pgset "xmit_mode netif_receive"
pgset "pkt_size 60"
pgset "dst 198.18.0.1"
pgset "dst_mac 90:e2:ba:ff:ff:ff"
pgset "count 10000000"
pgset "burst 32"
PGDEV=/proc/net/pktgen/pgctrl
echo "Running... ctrl^C to stop"
pgset "start"
echo "Done"
cat /proc/net/pktgen/$ETH
Usage:
$ sudo ./pktgen.sh eth2
...
Result: OK: 232376(c232372+d3) usec, 10000000 (60byte,0frags)
43033682pps 20656Mb/sec (20656167360bps) errors: 10000000
Raw netif_receive_skb speed should be ~43 million packet
per second on 3.7Ghz x86 and 'perf report' should look like:
37.69% kpktgend_0 [kernel.vmlinux] [k] __netif_receive_skb_core
25.81% kpktgend_0 [kernel.vmlinux] [k] kfree_skb
7.22% kpktgend_0 [kernel.vmlinux] [k] ip_rcv
5.68% kpktgend_0 [pktgen] [k] pktgen_thread_worker
If fib_table_lookup is seen on top, it means skb was processed
by the stack. To benchmark netif_receive_skb only make sure
that 'dst_mac' of your pktgen script is different from
receiving device mac and it will be dropped by ip_rcv
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow flag NO_TIMESTAMP to turn timestamping on again, like other flags,
with a negation of the flag like !NO_TIMESTAMP.
Also document the option flag NO_TIMESTAMP.
Fixes: afb84b6261 ("pktgen: add flag NO_TIMESTAMP to disable timestamping")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More accurately, listen all netns that have a nsid assigned into the netns
where the netlink socket is opened.
For this purpose, a netlink socket option is added:
NETLINK_LISTEN_ALL_NSID. When this option is set on a netlink socket, this
socket will receive netlink notifications from all netns that have a nsid
assigned into the netns where the socket has been opened. The nsid is sent
to userland via an anscillary data.
With this patch, a daemon needs only one socket to listen many netns. This
is useful when the number of netns is high.
Because 0 is a valid value for a nsid, the field nsid_is_set indicates if
the field nsid is valid or not. skb->cb is initialized to 0 on skb
allocation, thus we are sure that we will never send a nsid 0 by error to
the userland.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, nsid were protected by the rtnl lock. The goal of this
patch is to be able to find a nsid without needing to hold the rtnl lock.
The next patch will introduce a netlink socket option to listen to all
netns that have a nsid assigned into the netns where the socket is opened.
Thus, it's important to call rtnl_net_notifyid() outside the spinlock, to
avoid a recursive lock (nsid are notified via rtnl). This was the main
reason of the previous patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change with this patch. It will ease the refactoring
of the locking system that protects nsids and the support of the netlink
socket option NETLINK_LISTEN_ALL_NSID.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a following commit, a new function will be introduced to only lookup for
a nsid (no allocation if the nsid doesn't exist). To avoid confusion, the
existing function is renamed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this commit is to prepare the rework of the locking of nsnid
protection.
After this patch, rtnl_net_notifyid() will not call anymore __peernet2id(),
ie no idr_* operation into this function.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers of this function expect a nsid, not an error.
Thus, returns NETNSA_NSID_NOT_ASSIGNED in case of error so that callers
don't have to convert the error to NETNSA_NSID_NOT_ASSIGNED.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under tcp memory pressure, calling epoll_wait() in edge triggered
mode after -EAGAIN, can result in an indefinite hang in epoll_wait(),
even when there is sufficient memory available to continue making
progress. The problem is that when __sk_mem_schedule() returns 0
under memory pressure, we do not set the SOCK_NOSPACE flag in the
tcp write paths (tcp_sendmsg() or do_tcp_sendpages()). Then, since
SOCK_NOSPACE is used to trigger wakeups when incoming acks create
sufficient new space in the write queue, all outstanding packets
are acked, but we never wake up with the the EPOLLOUT that we are
expecting from epoll_wait().
This issue is currently limited to epoll() when used in edge trigger
mode, since 'tcp_poll()', does in fact currently set SOCK_NOSPACE.
This is sufficient for poll()/select() and epoll() in level trigger
mode. However, in edge trigger mode, epoll() is relying on the write
path to set SOCK_NOSPACE. EPOLL(7) says that in edge-trigger mode we
can only call epoll_wait() after read/write return -EAGAIN. Thus, in
the case of the socket write, we are relying on the fact that
tcp_sendmsg()/network write paths are going to issue a wakeup for
us at some point in the future when we get -EAGAIN.
Normally, epoll() edge trigger works fine when we've exceeded the
sk->sndbuf because in that case we do set SOCK_NOSPACE. However, when
we return -EAGAIN from the write path b/c we are over the tcp memory
limits and not b/c we are over the sndbuf, we are never going to get
another wakeup.
I can reproduce this issue, using SO_SNDBUF, since __sk_mem_schedule()
will return 0, or failure more readily with SO_SNDBUF:
1) create socket and set SO_SNDBUF to N
2) add socket as edge trigger
3) write to socket and block in epoll on -EAGAIN
4) cause tcp mem pressure via: echo "<small val>" > net.ipv4.tcp_mem
The fix here is simply to set SOCK_NOSPACE in sk_stream_wait_memory()
when the socket is non-blocking. Note that SOCK_NOSPACE, in addition
to waking up outstanding waiters is also used to expand the size of
the sk->sndbuf. However, we will not expand it by setting it in this
case because tcp_should_expand_sndbuf(), ensures that no expansion
occurs when we are under tcp memory pressure.
Note that we could still hang if sk->sk_wmem_queue is 0, when we get
the -EAGAIN. In this case the SOCK_NOSPACE bit will not help, since we
are waiting for and event that will never happen. I believe
that this case is harder to hit (and did not hit in my testing),
in that over the tcp 'soft' memory limits, we continue to guarantee a
minimum write buffer size. Perhaps, we could return -ENOSPC in this
case, or maybe we simply issue a wakeup in this case, such that we
keep retrying the write. Note that this case is not specific to
epoll() ET, but rather would affect blocking sockets as well. So I
view this patch as bringing epoll() edge-trigger into sync with the
current poll()/select()/epoll() level trigger and blocking sockets
behavior.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seccomp has always been a special candidate when it comes to preparation
of its filters in seccomp_prepare_filter(). Due to the extra checks and
filter rewrite it partially duplicates code and has BPF internals exposed.
This patch adds a generic API inside the BPF code code that seccomp can use
and thus keep it's filter preparation code minimal and better maintainable.
The other side-effect is that now classic JITs can add seccomp support as
well by only providing a BPF_LDX | BPF_W | BPF_ABS translation.
Tested with seccomp and BPF test suites.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When seccomp BPF was added, it was discussed to add __GFP_NOWARN
flag for their configuration path as f.e. up to 32K allocations are
more prone to fail under stress. As we're going to reuse BPF API,
add __GFP_NOWARN flags where larger kmalloc() and friends allocations
could fail.
It doesn't make much sense to pass around __GFP_NOWARN everywhere as
an extra argument only for seccomp while we just as well could run
into similar issues for socket filters, where it's not desired to
have a user application throw a WARN() due to allocation failure.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the calls to bpf_check_classic(), bpf_convert_filter() and
bpf_migrate_runtime() and let bpf_prepare_filter() take care of that
instead.
seccomp_check_filter() is passed to bpf_prepare_filter() so that it
gets called from there, after bpf_check_classic().
We can now remove exposure of two internal classic BPF functions
previously used by seccomp. The export of bpf_check_classic() symbol,
previously known as sk_chk_filter(), was there since pre git times,
and no in-tree module was using it, therefore remove it.
Joint work with Daniel Borkmann.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation for use by the seccomp code, the rationale is
not to duplicate additional code within the seccomp layer, but instead,
have it abstracted and hidden within the classic BPF API.
As an interim step, this now also makes bpf_prepare_filter() visible
(not as exported symbol though), so that seccomp can reuse that code
path instead of reimplementing it.
Joint work with Daniel Borkmann.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> net/core/skbuff.c:4108:13: sparse: incorrect type in assignment (different base types)
> net/ipv6/mcast_snoop.c:63 ipv6_mc_check_exthdrs() warn: unsigned 'offset' is never less than zero.
Introduced by 9afd85c9e4
("net: Export IGMP/MLD message validation code")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.
In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations. For example:
# ip l a link eth0 name eth0.10 type vlan id 10
# ip l a dev br0 typ bridge
# ip l s eth0.10 master br0
# ip l s eth0 master br0 <--- Will fail
If you switch the last two commands (add eth0 first), then both
will succeed. If after that, you remove eth0 and try to re-add
it, it will fail!
It appears to be enough to simply check adj_list to keeps things
safe.
I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c243d7e209.
That patch is solving a non-existant problem while creating a
real problem. Just because a socket is allocated in the init
name space doesn't mean that it gets hashed in the init name space.
When we unhash it the name space must be the same as the one
we had when we hashed it. So this patch is completely bogus
and causes socket leaks.
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users of flow keys (well just sch_choke now) need to pass
flow_keys in skbuff cb, and use them for exact comparisons of flows
so that skb->hash is not sufficient. In order to increase size of
the flow_keys structure, we introduce another structure for
the purpose of passing flow keys in skbuff cb. We limit this structure
to sixteen bytes, and we will technically treat this as a digest of
flow_keys struct hence its name flow_keys_digest. In the first
incaranation we just copy the flow_keys structure up to 16 bytes--
this is the same information previously passed in the cb. In the
future, we'll adapt this for larger flow_keys and could use something
like SHA-1 over the whole flow_keys to improve the quality of the
digest.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This calls flow_disect and __skb_get_hash to procure a hash for a
packet. Input includes a key to initialize jhash. This function
does not set skb->hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC classifiers/actions were converted to RCU by John in the series:
http://thread.gmane.org/gmane.linux.network/329739/focus=329739
and many follow on patches.
This is the last patch from that series that finally drops
ingress spin_lock.
Single cpu ingress+u32 performance goes from 22.9 Mpps to 24.5 Mpps.
In two cpu case when both cores are receiving traffic on the same
device and go into the same ingress+u32 the performance jumps
from 4.5 + 4.5 Mpps to 23.5 + 23.5 Mpps
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 567e4b7973 ("net: rfs: add hash collision detection") had one
mistake :
RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask
This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.
In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.
Fixes: 567e4b7973 ("net: rfs: add hash collision detection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() should look at the page pfmemalloc status.
If set, this means page allocator allocated this page in the
expectation it would help to free other pages. Networking
stack can do that only if skb->pfmemalloc is also set.
Also, we must refrain using high order pages from the pfmemalloc
reserve, so __page_frag_refill() must also use __GFP_NOMEMALLOC for
them. Under memory pressure, using order-0 pages is probably the best
strategy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for hrtimer_active() after starting the timer is
pointless. If the timer is inactive it has expired already and
therefor the task pointer is already NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20150414203503.165258315@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit 04ffcb255f ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().
Then later, when generalizing this in commit 5f35227ea3
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.
Remove the unused argument and go back to the code as before.
Cc: Tom Herbert <therbert@google.com>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, Apr 15, 2015 at 05:41:26PM +0200, Nicolas Dichtel wrote:
> Le 15/04/2015 15:57, Herbert Xu a écrit :
> >On Wed, Apr 15, 2015 at 06:22:29PM +0800, Herbert Xu wrote:
> [snip]
> >Subject: skbuff: Do not scrub skb mark within the same name space
> >
> >The commit ea23192e8e ("tunnels:
> Maybe add a Fixes tag?
> Fixes: ea23192e8e ("tunnels: harmonize cleanup done on skb on rx path")
>
> >harmonize cleanup done on skb on rx path") broke anyone trying to
> >use netfilter marking across IPv4 tunnels. While most of the
> >fields that are cleared by skb_scrub_packet don't matter, the
> >netfilter mark must be preserved.
> >
> >This patch rearranges skb_scurb_packet to preserve the mark field.
> nit: s/scurb/scrub
>
> Else it's fine for me.
Sure.
PS I used the wrong email for James the first time around. So
let me repeat the question here. Should secmark be preserved
or cleared across tunnels within the same name space? In fact,
do our security models even support name spaces?
---8<---
The commit ea23192e8e ("tunnels:
harmonize cleanup done on skb on rx path") broke anyone trying to
use netfilter marking across IPv4 tunnels. While most of the
fields that are cleared by skb_scrub_packet don't matter, the
netfilter mark must be preserved.
This patch rearranges skb_scrub_packet to preserve the mark field.
Fixes: ea23192e8e ("tunnels: harmonize cleanup done on skb on rx path")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit b8fb4e0648
because the secmark must be preserved even when a packet crosses
namespace boundaries. The reason is that security labels apply to
the system as a whole and is not per-namespace.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the short-term solution, lets fix bpf helper functions to use
skb->mac_header relative offsets instead of skb->data in order to
get the same eBPF programs with cls_bpf and act_bpf work on ingress
and egress qdisc path. We need to ensure that mac_header is set
before calling into programs. This is effectively the first option
from below referenced discussion.
More long term solution for LD_ABS|LD_IND instructions will be more
intrusive but also more beneficial than this, and implemented later
as it's too risky at this point in time.
I.e., we plan to look into the option of moving skb_pull() out of
eth_type_trans() and into netif_receive_skb() as has been suggested
as second option. Meanwhile, this solution ensures ingress can be
used with eBPF, too, and that we won't run into ABI troubles later.
For dealing with negative offsets inside eBPF helper functions,
we've implemented bpf_skb_clone_unwritable() to test for unwriteable
headers.
Reference: http://thread.gmane.org/gmane.linux.network/359129/focus=359694
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3 ("tc: bpf: add checksum helpers")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro says:
====================
netdev-related stuff in vfs.git
There are several commits sitting in vfs.git that probably ought to go in
via net-next.git. First of all, there's merge with vfs.git#iocb - that's
Christoph's aio rework, which has triggered conflicts with the ->sendmsg()
and ->recvmsg() patches a while ago. It's not so much Christoph's stuff
that ought to be in net-next, as (pretty simple) conflict resolution on merge.
The next chunk is switch to {compat_,}import_iovec/import_single_range - new
safer primitives for initializing iov_iter. The primitives themselves come
from vfs/git#iov_iter (and they are used quite a lot in vfs part of queue),
conversion of net/socket.c syscalls belongs in net-next, IMO. Next there's
afs and rxrpc stuff from dhowells. And then there's sanitizing kernel_sendmsg
et.al. + missing inlined helper for "how much data is left in msg->msg_iter" -
this stuff is used in e.g. cifs stuff, but it belongs in net-next.
That pile is pullable from
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs.git for-davem
I'll post the individual patches in there in followups; could you take a look
and tell if everything in there is OK with you?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we make use of classifier and actions from the egress
path, we're going into handle_ing() executing additional code
on a per-packet cost for ingress qdisc, just to realize that
nothing is attached on ingress.
Instead, this can just be blinded out as a no-op entirely with
the use of a static key. On input fast-path, we already make
use of static keys in various places, e.g. skb time stamping,
in RPS, etc. It makes sense to not waste time when we're assured
that no ingress qdisc is attached anywhere.
Enabling/disabling of that code path is being done via two
helpers, namely net_{inc,dec}_ingress_queue(), that are being
invoked under RTNL mutex when a ingress qdisc is being either
initialized or destructed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-04-11
This series contains updates to iflink, ixgbe and ixgbevf.
The entire set of changes come from Vlad Zolotarov to ultimately add
the ethtool ops to VF driver to allow querying the RSS indirection table
and RSS random key.
Currently we support only 82599 and x540 devices. On those devices, VFs
share the RSS redirection table and hash key with a PF. Letting the VF
query this information may introduce some security risks, therefore this
feature will be disabled by default.
The new netdev op allows a system administrator to change the default
behaviour with "ip link set" command. The relevant iproute2 patch has
already been sent and awaits for this series upstream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent adoption of skc_cookie in struct sock_common,
struct tcp_timewait_sock size increased from 192 to 200 bytes
on 64bit arches. SLAB rounds then to 256 bytes.
It is time to drop SLAB_HWCACHE_ALIGN constraint for twsk_slab.
This saves about 12 MB of memory on typical configuration reaching
262144 timewait sockets, and has no noticeable impact on performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration setting for drivers to allow/block an RSS Redirection
Table and a Hash Key querying for discrete VFs.
On some devices VF share the mentioned above information with PF and
querying it may adduce a theoretical security risk. We want to let a
system administrator to decide if he/she wants to take this risk or not.
Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an FDB entry is added or deleted the information about VLAN
is not passed to listening applications like 'bridge monitor fdb'.
With this patch VLAN ID is passed if it was set in the original
netlink message.
Also remove an unused bdev variable.
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which this patch, it's possible to dump the list of ids allocated for peer
netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, netns ids that are created and deleted are advertised into the
group RTNLGRP_NSID.
Because callers of rtnl_net_notifyid() already know the id of the peer, there is
no need to call __peernet2id() in rtnl_net_fill().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to initialize err, it will be overridden by the value of nlmsg_parse().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 608cd71a9c ("tc: bpf: generalize pedit action") has added the
possibility to mangle packet data to BPF programs in the tc pipeline.
This patch adds two helpers bpf_l3_csum_replace() and bpf_l4_csum_replace()
for fixing up the protocol checksums after the packet mangling.
It also adds 'flags' argument to bpf_skb_store_bytes() helper to avoid
unnecessary checksum recomputations when BPF programs adjusting l3/l4
checksums and documents all three helpers in uapi header.
Moreover, a sample program is added to show how BPF programs can make use
of the mangle and csum helpers.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.
ipv6 does not conform with this in three places:
1) ip6_fragment: we do consult ipv6_npinfo for frag_size
2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
loop the packet back to the local socket
3) ip6_skb_dst_mtu could query the settings from the user socket and
force a wrong MTU
Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.
Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability to read out the skb->priority from an eBPF
program, so that it can be taken into account from a tc filter
or action for the use-case where the priority is not being used
to directly override the filter classification in a qdisc, but
to tag traffic otherwise for the classifier; the priority can be
assigned from various places incl. user space, in future we may
also mangle it from an eBPF program.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, let's explain the problem.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
- the bar nsid into the netns foo is removed
- the netns exit method of ipip is called, thus our ipip iface is removed:
=> a netlink message is built in the netns foo to advertise this deletion
=> this netlink message requests an nsid for bar, thus a new nsid is
allocated for bar and never removed.
This patch adds a check in peernet2id() so that an id cannot be allocated for
a netns which is currently destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts
commit 4217291e59 ("netns: don't clear nsid too early on removal").
This is not the right fix, it introduces races.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to hold rtnl lock for fib_rules_unregister()
otherwise the following race could happen:
fib_rules_unregister(): fib_nl_delrule():
... ...
... ops = lookup_rules_ops();
list_del_rcu(&ops->list);
list_for_each_entry(ops->rules) {
fib_rules_cleanup_ops(ops); ...
list_del_rcu(); list_del_rcu();
}
Note, net->rules_mod_lock is actually not needed at all,
either upper layer netns code or rtnl lock guarantees
we are safe.
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual interfaces are supposed to set an iflink value != of their ifindex.
It was not the case for some of them, like vxlan, bond or bridge.
Let's set iflink to 0 when dev->rtnl_link_ops is set.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users of iflink have the ndo_get_iflink handler available, it's
possible to remove this field.
By default, dev_get_iflink() returns the ifindex of the interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other places, this function uses name "dev" for what should be
"orig_dev", which might be a bit confusing. So fix this.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
As there are a number of (especially virtual) devices that don't
need the multiple vlan check, introduce passthru_features_check() for
convenience.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the two checks for single vlan and multiple vlans in
netif_skb_features(). This allows us to move the check for multiple
vlans to another function later.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
existing TC action 'pedit' can munge any bits of the packet.
Generalize it for use in bpf programs attached as cls_bpf and act_bpf via
bpf_skb_store_bytes() helper function.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current code, ids are removed too early.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
- the bar nsid into the netns foo is removed
- the netns exit method of ipip is called, thus our ipip iface is removed:
=> a netlink message is sent in the netns foo to advertise this deletion
=> this netlink message requests an nsid for bar, thus a new nsid is
allocated for bar and never removed.
We must remove nsids when we are sure that nobody will refer to netns currently
cleaned.
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vlan offloading takes place then vlan header is removed from frame
and its contents, both vlan_tci and vlan_proto, is available to user
space via TPACKET interface. However, only vlan_tci can be used in BPF
filters.
This commit introduces a new BPF extension. It makes possible to load
the value of vlan_proto (vlan TPID) to register A. Support for classic
BPF and eBPF is being added, analogous to skb->protocol.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
With dev group, we can change a batch of net devices,
so we should allow to delete them together too.
Group 0 is not allowed to be deleted since it is
the default group.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We implement the SO_SNDLOWAT etc not to be settable and return
ENOPROTOOPT per 1003.1g 7. Move the comment to appropriate
position and update the reference.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a low hanging fruit, as we'll get rid of syn_wait_lock eventually.
We hold syn_wait_lock for such small sections, that it makes no sense to use
a read/write lock. A spin lock is simply faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->priority can be set for two purposes:
1) With respect to IP TOS field, which is computed by a mask.
Ususally used for priority qdisc's (pfifo, prio etc.), on TX
side (we only have ingress qdisc on RX side).
2) Used as a classid or flowid, works in the same way with tc
classid. What's more, this can even override the classid
of tc filters.
For case 1), it has been respected within its netns, I don't
see any point of keeping it for another netns, especially
when packets will be forwarded to Rx path (no matter from TX
path or RX path).
For case 2) we care, our applications run inside a netns,
and we classify the packets by our own filters outside,
If some application sets this priority, it could bypass
our filters, therefore clear it when moving out of a netns,
it makes no sense to bypass tc filters out of its netns.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We send unicast neighbor (ARP or NDP) solicitations ucast_probes
times in PROBE state. Zhu Yanjun reported that some implementation
does not reply against them and the entry will become FAILED, which
is undesirable.
We had been dealt with such nodes by sending multicast probes mcast_
solicit times after unicast probes in PROBE state. In 2003, I made
a change not to send them to improve compatibility with IPv6 NDP.
Let's introduce per-protocol per-interface sysctl knob "mcast_
reprobe" to configure the number of multicast (re)solicitation for
reconfirmation in PROBE state. The default is 0, since we have
been doing so for 10+ years.
Reported-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
CC: Ulf Samuelsson <ulf.samuelsson@ericsson.com>
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prepare eBPF support for tc action, we need to add
sched_act_type, so that the eBPF verifier is aware of what helper
function act_bpf may use, that it can load skb data and read out
currently available skb fields.
This is bascially analogous to 96be4325f4 ("ebpf: add sched_cls_type
and map it to sk_filter's verifier ops").
BPF_PROG_TYPE_SCHED_CLS and BPF_PROG_TYPE_SCHED_ACT need to be
separate since both will have a different set of functionality in
future (classifier vs action), thus we won't run into ABI troubles
when the point in time comes to diverge functionality from the
classifier.
The future plan for act_bpf would be that it will be able to write
into skb->data and alter selected fields mirrored in struct __sk_buff.
For an initial support, it's sufficient to map it to sk_filter_ops.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c249739579 ("bpf: allow BPF programs access 'protocol' and 'vlan_tci'
fields") has added support for accessing protocol, vlan_present and vlan_tci
into the skb offset map.
As referenced in the below discussion, accessing skb->protocol from an eBPF
program should be converted without handling endianess.
The reason for this is that an eBPF program could simply do a check more
naturally, by f.e. testing skb->protocol == htons(ETH_P_IP), where the LLVM
compiler resolves htons() against a constant automatically during compilation
time, as opposed to an otherwise needed run time conversion.
After all, the way of programming both from a user perspective differs quite
a lot, i.e. bpf_asm ["ld proto"] versus a C subset/LLVM.
Reference: https://patchwork.ozlabs.org/patch/450819/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_ack_backlog & sk_max_ack_backlog were 16bit fields, meaning
listen() backlog was limited to 65535.
It is time to increase the width to allow much bigger backlog,
if admins change /proc/sys/net/core/somaxconn &
/proc/sys/net/ipv4/tcp_max_syn_backlog default values.
Tested:
echo 5000000 >/proc/sys/net/core/somaxconn
echo 5000000 >/proc/sys/net/ipv4/tcp_max_syn_backlog
Ran a SYNFLOOD test against a listener using listen(fd, 5000000)
myhost~# grep request_sock_TCP /proc/slabinfo
request_sock_TCP 4185642 4411940 304 13 1 : tunables 54 27 8 : slabdata 339380 339380 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the major issue for TCP is the SYNACK rtx handling,
done by inet_csk_reqsk_queue_prune(), fired by the keepalive
timer of a TCP_LISTEN socket.
This function runs for awful long times, with socket lock held,
meaning that other cpus needing this lock have to spin for hundred of ms.
SYNACK are sent in huge bursts, likely to cause severe drops anyway.
This model was OK 15 years ago when memory was very tight.
We now can afford to have a timer per request sock.
Timer invocations no longer need to lock the listener,
and can be run from all cpus in parallel.
With following patch increasing somaxconn width to 32 bits,
I tested a listener with more than 4 million active request sockets,
and a steady SYNFLOOD of ~200,000 SYN per second.
Host was sending ~830,000 SYNACK per second.
This is ~100 times more what we could achieve before this patch.
Later, we will get rid of the listener hash and use ehash instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.
This is because of the call chain:
NETDEV_DOWN notifier
--> vlan_device_event()
--> dev_change_flags()
--> __dev_change_flags()
--> __dev_close()
--> __dev_close_many()
--> dev_deactivate_many()
--> synchronize_net()
This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.
So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list. Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to port id allow netdevices to specify port names and export
the name via sysfs. Drivers can implement the netdevice operation to
assist udev in having sane default names for the devices using the
rule:
$ cat /etc/udev/rules.d/80-net-setup-link.rules
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_port_name}!="",
NAME="$attr{phys_port_name}"
Use of phys_name versus phys_id was suggested-by Jiri Pirko.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a tx_maxrate attribute to the tx queue sysfs entry allowing
for max-rate limiting. Along with DCB-ETS and BQL this provides another
knob to tune queue performance. The limit units are Mbps.
By default it is disabled. To disable the rate limitation after it
has been set for a queue, it should be set to zero.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The listener field in struct tcp_request_sock is a pointer
back to the listener. We now have req->rsk_listener, so TCP
only needs one boolean and not a full pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as a follow on to patch 70006af955 ("bpf: allow eBPF access skb fields")
this patch allows 'protocol' and 'vlan_tci' fields to be accessible
from extended BPF programs.
The usage of 'protocol', 'vlan_present' and 'vlan_tci' fields is the same as
corresponding SKF_AD_PROTOCOL, SKF_AD_VLAN_TAG_PRESENT and SKF_AD_VLAN_TAG
accesses in classic BPF.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a kernel socket with sock_create_kern() happens in "init_net"
namespace, however, releasing it with sk_release_kernel() occurs in
the current namespace which may be different with "init_net" namespace.
Therefore, we should guarantee that the namespace in which a kernel
socket is created is same as the socket is created.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reqsk_put() is the generic function that should be used
to release a refcount (and automatically call reqsk_free())
reqsk_free() might be called if refcount is known to be 0
or undefined.
refcnt is set to one in inet_csk_reqsk_queue_add()
As request socks are not yet in global ehash table,
I added temporary debugging checks in reqsk_put() and reqsk_free()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_edemux() is not used in fast path, and should
really call sock_gen_put() to save some code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce user accessible mirror of in-kernel 'struct sk_buff':
struct __sk_buff {
__u32 len;
__u32 pkt_type;
__u32 mark;
__u32 queue_mapping;
};
bpf programs can do:
int bpf_prog(struct __sk_buff *skb)
{
__u32 var = skb->pkt_type;
which will be compiled to bpf assembler as:
dst_reg = *(u32 *)(src_reg + 4) // 4 == offsetof(struct __sk_buff, pkt_type)
bpf verifier will check validity of access and will convert it to:
dst_reg = *(u8 *)(src_reg + offsetof(struct sk_buff, __pkt_type_offset))
dst_reg &= 7
since skb->pkt_type is a bitfield.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the possibility to obtain raw_smp_processor_id() in
eBPF. Currently, this is only possible in classic BPF where commit
da2033c282 ("filter: add SKF_AD_RXHASH and SKF_AD_CPU") has added
facilities for this.
Perhaps most importantly, this would also allow us to track per CPU
statistics with eBPF maps, or to implement a poor-man's per CPU data
structure through eBPF maps.
Example function proto-type looks like:
u32 (*smp_processor_id)(void) = (void *)BPF_FUNC_get_smp_processor_id;
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work is similar to commit 4cd3675ebf ("filter: added BPF
random opcode") and adds a possibility for packet sampling in eBPF.
Currently, this is only possible in classic BPF and useful to
combine sampling with f.e. packet sockets, possible also with tc.
Example function proto-type looks like:
u32 (*prandom_u32)(void) = (void *)BPF_FUNC_get_prandom_u32;
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_edemux() & sock_gen_put() should be ready to cope with request socks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make proto_register() & proto_unregister() a bit nicer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hold_net and release_net were an idea that turned out to be useless.
The code has been disabled since 2008. Kill the code it is long past due.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that sk != NULL before reading sk->sk_tsflags.
Fixes: 49ca0d8bfa ("net-timestamp: no-payload option")
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John reported that my previous commit added a regression
on his router.
This is because sender_cpu & napi_id share a common location,
so get_xps_queue() can see garbage and perform an out of bound access.
We need to make sure sender_cpu is cleared before doing the transmit,
otherwise any NIC busy poll enabled (skb_mark_napi_id()) can trigger
this bug.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: John <jw@nuclearfallout.net>
Bisected-by: John <jw@nuclearfallout.net>
Fixes: 2bd82484bb ("xps: fix xps for stacked devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem in netlink socket dumps is the use
of kernel socket addresses as cookies.
1) It is a security concern.
2) Sockets can be reused quite quickly, so there is
no guarantee a cookie is used once and identify
a flow.
3) request sock, establish sock, and timewait socks
for a given flow have different cookies.
Part of our effort to bring better TCP statistics requires
to switch to a different allocator.
In this patch, I chose to use a per network namespace 64bit generator,
and to use it only in the case a socket needs to be dumped to netlink.
(This might be refined later if needed)
Note that I tried to carry cookies from request sock, to establish sock,
then timewait sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric Salo <salo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to collapse local and main into one by converting
tb_data from an array to a pointer. Doing this allows us to point the
local table into the main while maintaining the same variables in the
table.
As such the tb_data was converted from an array to a pointer, and a new
array called data is added in order to still provide an object for tb_data
to point to.
In order to track the origin of the fib aliases a tb_id value was added in
a hole that existed on 64b systems. Using this we can also reverse the
merge in the event that custom FIB rules are enabled.
With this patch I am seeing an improvement of 20ns to 30ns for routing
lookups as long as custom rules are not enabled, with custom rules enabled
we fall back to split tables and the original behavior.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rtnl_newlink() fails on it's call to dev_change_net_namespace(), we
have to make use of the ->dellink() method, if present, just like we
do when rtnl_configure_link() fails.
Fixes: 317f4810e4 ("rtnl: allow to create device with IFLA_LINK_NETNSID set")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_diag_check_cookie() second parameter is constant
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function which allows getting the struct net_device pointer
associated with a given struct device_node pointer. This is useful for
instance for DSA Ethernet devices not backed by a platform_device, but a PCI
device.
Since we need to access net_class which is not accessible outside of
net/core/net-sysfs.c, this helper function is also added here and gated
with CONFIG_OF_NET.
Network devices initialized with SET_NETDEV_DEV() are also taken into
account by checking for dev->parent first and then falling back to
checking the device pointer within struct net_device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
