When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.
The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.
This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).
In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.
Fixes: d521432149 ("ASoC: tlv320adcx140: Add support for configuring GPIO pin")
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the function name aw88395_plack_event to aw88395_playback_event
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230213093649.22928-2-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2458adb8f9
("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
added a call to snd_soc_dai_set_sysclk() with 0 Hz frequency. Being
propagated further it causes a division by zero in clk-ep93xx driver:
Division by zero in kernel.
CPU: 0 PID: 52 Comm: aplay Tainted: G W 6.2.0-rc4-... #1
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x18
show_stack from dump_stack_lvl+0x28/0x34
dump_stack_lvl from __div0+0x10/0x1c
__div0 from Ldiv0+0x8/0x1c
Ldiv0 from ep93xx_mux_determine_rate+0x78/0x1d0
ep93xx_mux_determine_rate from clk_core_round_rate_nolock+0x48/0xc8
clk_core_round_rate_nolock from clk_core_set_rate_nolock+0x48/0x160
clk_core_set_rate_nolock from clk_set_rate+0x30/0x8c
clk_set_rate from ep93xx_i2s_set_sysclk+0x30/0x6c
ep93xx_i2s_set_sysclk from snd_soc_dai_set_sysclk+0x3c/0xa4
snd_soc_dai_set_sysclk from asoc_simple_shutdown+0xb8/0x164
asoc_simple_shutdown from snd_soc_link_shutdown+0x44/0x54
snd_soc_link_shutdown from soc_pcm_clean+0x78/0x180
soc_pcm_clean from soc_pcm_close+0x28/0x40
soc_pcm_close from snd_pcm_release_substream.part.0+0x3c/0x84
snd_pcm_release_substream.part.0 from snd_pcm_release+0x40/0x88
snd_pcm_release from __fput+0x74/0x278
There has been commit f1879d7b98 ("ASoC: rockchip: ignore 0Hz sysclk"),
but it prepared by far not all drivers.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230212220923.258414-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO2 PIN use for output. Mask Dir and Data need to assign for 0x4. Not 0x3.
This fixed was for Lenovo Desktop(0x17aa1056). GPIO2 use for AMP enable.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/8d02bb9ac8134f878cd08607fdf088fd@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230211-kobj_type-sound-v1-1-17107ceb25b7@weissschuh.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit f2bd1c5ae2 ("ALSA: hda: Fix page fault in
snd_hda_codec_shutdown()") relocated initialization of several codec
device fields. Due to differences between codec_exec_verb() and
snd_hdac_bus_exec_bus() in how they handle VERB execution - the latter
does not touch PM - assigning ->exec_verb to codec_exec_verb() causes PM
to be engaged before it is configured for the device. Configuration of
PM for the ASoC HDAudio sound card is done with snd_hda_set_power_save()
during skl_hda_audio_probe() whereas the assignment happens early, in
snd_hda_codec_device_init().
Revert to previous behavior to avoid problems caused by too early PM
manipulation.
Suggested-by: Jason Montleon <jmontleo@redhat.com>
Link: https://lore.kernel.org/regressions/CALFERdzKUodLsm6=Ub3g2+PxpNpPtPq3bGBLbff=eZr9_S=YVA@mail.gmail.com
Fixes: f2bd1c5ae2 ("ALSA: hda: Fix page fault in snd_hda_codec_shutdown()")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230210165541.3543604-1-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hopefully the last one for 6.2, a collection of the fixes that have
been gathered since the last PR. All changes are small and trivial
device-specific fixes.
-----BEGIN PGP SIGNATURE-----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=fz1j
-----END PGP SIGNATURE-----
Merge tag 'sound-6.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last one for 6.2, a collection of the fixes that have
been gathered since the last pull.
All changes are small and trivial device-specific fixes"
* tag 'sound-6.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add Positivo N14KP6-TG
ASoC: topology: Return -ENOMEM on memory allocation failure
ALSA: emux: Avoid potential array out-of-bound in snd_emux_xg_control()
ASoC: fsl_sai: fix getting version from VERID
ALSA: hda/realtek: fix mute/micmute LEDs don't work for a HP platform.
ALSA: hda/realtek: Add quirk for ASUS UM3402 using CS35L41
ASoC: codecs: es8326: Fix DTS properties reading
ASoC: tas5805m: add missing page switch.
ASoC: tas5805m: rework to avoid scheduling while atomic.
ALSA: hda/realtek: Enable mute/micmute LEDs on HP Elitebook, 645 G9
ASoC: SOF: amd: Fix for handling spurious interrupts from DSP
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro 360
ALSA: pci: lx6464es: fix a debug loop
ASoC: rt715-sdca: fix clock stop prepare timeout issue
This patch fixes
1. coding style issues
2. check if the setting was set already in rt712_sdca_mux_put callback
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230210082141.24077-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd silently uses default TDM width if it was strange
settings. It is difficult to notice about it.
This patch indicates warning for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lel6ksqn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This 2nd variables are all set as true in treewide. So I think
it can be removed for easy understanding.
Signed-off-by: Zhang Yiqun <zhangyiqun@phytium.com.cn>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230209121723.14328-1-zhangyiqun@phytium.com.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace direct modifications to vma->vm_flags with calls to modifier
functions to be able to track flag changes and to keep vma locking
correctness.
[akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo]
Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Oskolkov <posk@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
From q6dsp side issues are around locking of position pointer and handle
From LPASS codec side most of the staiblity issues were around runtime pm,:
While testing X13s audio, we found multiple stablity issues this patchset
fixes these issues.
From q6dsp side issues are around locking of position pointer and handle
multiple prepare cases along with pulse audio timerbased scheduling workaround.
From LPASS codec side most of the staiblity issues were around runtime pm,
hitting various issues as the codec was firstly resetting the soundwire block
for every clk disable/enable which is taking the slaves out of sync and
resulting in re-enumerating. Second issue was around fsgen clk is not
brining up the codec out of suspend as it was not added after
runtime pm enabled. Final issue was with codec mclk rate which should
have been 192KHz same as npl instead of 96KHz. We were getting lucky as
wsa drivers are setting the same clk to 192KHz.
With this patches, x13s audio is pretty stable.
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
In a course of creating complicated topologies where multiple output pins of a
copier is enabled, we have discovered that additional configuration needs to be
sent to the firmware to make the use cases working.
Merge series from Herve Codina <herve.codina@bootlin.com>:
The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.
This is the initial codec driver for rt712 SDCA (Jack+Amp topology).
The host should connect with rt712 SdW1 interface.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230207090946.20659-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
This is inspired from,
commit dbf54a9534 ("ASoC: rt5659: Update MCLK rate in set_sysclk()").
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1675953417-8686-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230206144904.91078-3-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MOD_INIT_INSTANCE IPC for a copier only contains the sink format for
output pin 0. Any additional output pins that are used need to have their
sink format set using the LARGE_CONFIG_SET IPC message.
Otherwise, firmware will report error or crash due to NULL format is used.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Print the queue ID's during bind/unbind errors as well to make it easier
to see what failed exactly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
resetting soundwire block will put the slaves out of sync and result
in re-enumeration during fsgen disable/enable path this is totally
unnecessary and resulting fifo overflows.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-8-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
currently q6apm_is_adsp_ready() will only return the cached value of
previous result. If we are unlucky and previous result is not-ready
then the caller will always get not-ready flag.
This is not correct, we should query the dsp of its current state in
irrespective of previous reported state.
Fixes: 47bc8cf60e ("ASoC: qdsp6: audioreach: Add ADSP ready check")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment, playing audio with PulseAudio with the qdsp6 driver
results in distorted sound. It seems like its timer-based scheduling
does not work properly with qdsp6 since setting tsched=0 in
the PulseAudio configuration avoids the issue.
Apparently this happens when the pointer() callback is not accurate
enough. There is a SNDRV_PCM_INFO_BATCH flag that can be used to stop
PulseAudio from using timer-based scheduling by default.
According to https://www.alsa-project.org/pipermail/alsa-devel/2014-March/073816.html:
The flag is being used in the sense explained in the previous audio
meeting -- the data transfer granularity isn't fine enough but aligned
to the period size (or less).
q6apm-dai reports the position as multiple of
prtd->pcm_count = snd_pcm_lib_period_bytes(substream)
so it indeed just a multiple of the period size.
Therefore adding the flag here seems appropriate and makes audio
work out of the box.
Comment log inspired by Stephan Gerhold sent for q6asm-dai.c few years back.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is noticed that the position pointer value seems to get a get corrupted
due to missing locking between updating and reading.
Fix this by adding a spinlock around the position pointer.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare callback can be called multiple times, so unprepare the stream
if its already prepared.
Without this DSP is not happy to setting the params on a already
prepared graph.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
All callers from other files ignore the return value of this function.
And it can only ever return a non-zero value if the parameter card is NULL.
This cannot happen in snd_card_free() as card was dereferenced just before
snd_card_free_when_closed() is called. So the error handling can be dropped
there.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Geoff Levand <geoff@infradead.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230207191907.467756-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All callers from other files ignore the return value of this function.
And it can only ever return a non-zero value if the parameter card is NULL.
Move the check for card being NULL into snd_card_free_when_closed() to keep
the previous behaviour. Note this isn't necessary for
snd_card_disconnect_sync() because if card was NULL in there the dereference
of card for dev_err() would oops the kernel. Replace this by an oops
triggered by the dereference of card for spin_lock_irq().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Geoff Levand <geoff@infradead.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230207191907.467756-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SOF driver calls snd_sof_dsp_update8 with parameters mask and value but
the snd_sof_dsp_update8 declares these two parameters in reverse order.
This causes some issues such as d0i3 register can't be set correctly
Now change function definition according to common SOF usage.
Fixes: c28a36b012 ("ASoC: SOF: ops: add snd_sof_dsp_updateb() helper")
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230208104404.20554-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few more fixes for v6.2, all driver specific and small. It's larger
than is ideal but we can't really control when people find problems.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmPifS4ACgkQJNaLcl1U
h9AG5wf9EKiquRiuxSxtLrZdPO2xRBgcfZBbTqPeRvYGWeCzYaKFwcjI5UlJZ3Kz
tdymQ9tihVkcdrEH6xin3QETUI+8vU9++Vh1XVNN01GaSrMq9SupYFR5UvN5QNuD
SfjtDt7oWWzlFwOouDnLC5T/5U5iWqFVd/hHvZWHsCFJYIPzBvNTnXhQ8My/88Lf
2Fmn1/3HTDzNhTTrPdVK84ZIMVb7IbfMcFw4E9+Yk9jtGtfQXtK0l6VzJCwgS6Kl
85CZ51pPKCx4X18iDqyc0j5dcqAjI08FAa0i9Rfix3Sz0GXRsW7CemnFQSOR7Zw4
QQiBIMAIFEp4UzeBG9K79IPh/B9biA==
=hxoQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.2-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.2
A few more fixes for v6.2, all driver specific and small. It's larger
than is ideal but we can't really control when people find problems.
When handling error path, ret needs to be set to correct value.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: d29d41e28e ("ASoC: topology: Add support for multiple kcontrol types to a widget")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230207210428.2076354-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_emux_xg_control() can be called with an argument 'param' greater
than size of 'control' array. It may lead to accessing 'control'
array at a wrong index.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Artemii Karasev <karasev@ispras.ru>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230207132026.2870-1-karasev@ispras.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The version information is at the bit31 ~ bit16 in the VERID
register, so need to right shift 16bit to get it, otherwise
the result of comparison "sai->verid.version >= 0x0301" is
wrong.
Fixes: 99c1e74f25 ("ASoC: fsl_sai: store full version instead of major/minor")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1675760664-25193-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a HP platform needs ALC236_FIXUP_HP_GPIO_LED quirk to
make mic-mute/audio-mute working.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230207083011.100189-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Daniel Beer <daniel.beer@igorinstitute.com>:
This pair of patches fixes two issues which crept in while revising the
original submission, at a time when I no longer had access to test
hardware.
The fixes here have been tested and verified on hardware.
This Asus Zenbook laptop use Realtek HDA codec combined with
2xCS35L41 Amplifiers using I2C with External Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230206150019.3825120-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The val is defined as unsigned int type, if(val<0) is redundant, so
delete it.
sound/soc/codecs/idt821034.c:449 idt821034_kctrl_gain_put() warn: unsigned 'val' is never less than zero.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3947
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230206075518.84169-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck reports
sound/soc/codecs/aw88395/aw88395_lib.c:789:6: error: Uninitialized variable: cur_scene_id [uninitvar]
if (cur_scene_id == 0) {
^
Passing a garbage value to aw_dev_parse_data_by_sec_type_v1() will cause a crash
when the value is used as an array index. This check assumes cur_scene_id is
initialized to 0, so initialize it to 0.
Fixes: 4345865b00 ("ASoC: codecs: ACF bin parsing and check library file for aw88395")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230205015733.1721009-1-trix@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Seems like properties parsing and reading was copy-pasted,
so "everest,interrupt-src" and "everest,interrupt-clk" are saved into
the es8326->jack_pol variable. This might lead to wrong settings
being saved into the reg 57 (ES8326_HP_DET).
Fix this by using proper variables while reading properties.
Signed-off-by: Alexey Firago <a.firago@yadro.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com
Link: https://lore.kernel.org/r/20230204195106.46539-1-a.firago@yadro.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In tas5805m_refresh, we switch pages to update the DSP volume control,
but we need to switch back to page 0 before trying to alter the
soft-mute control. This latter page-switch was missing.
Fixes: ec45268467 ("ASoC: add support for TAS5805M digital amplifier")
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/1fea38a71ea6ab0225d19ab28d1fa12828d762d0.1675497326.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's some setup we need to do in order to get the DSP initialized,
and this can't be done until a bit-clock is ready. In an earlier version
of this driver, this work was done in a DAPM callback.
The DAPM callback doesn't guarantee that the bit-clock is running, so
the work was moved instead to the trigger callback. Unfortunately this
callback runs in atomic context, and the setup code needs to do I2C
transactions.
Here we use a work_struct to kick off the setup in a thread instead.
Fixes: ec45268467 ("ASoC: add support for TAS5805M digital amplifier")
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/85d8ba405cb009a7a3249b556dc8f3bdb1754fdf.1675497326.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Elitebook 645 G9 laptop (with motherboard model 89D2) uses the
ALC236 codec and requires the alc236_fixup_hp_mute_led_micmute_vref
fixup in order to enable mute/micmute LEDs.
Note: the alc236_fixup_hp_gpio_led fixup, which is used by the Elitebook
640 G9, does not work with the 645 G9.
[ rearranged the entry in SSID order -- tiwai ]
Signed-off-by: Elvis Angelaccio <elvis.angelaccio@kde.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4055cb48-e228-8a13-524d-afbb7aaafebe@kde.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current structure includes no field to express the number of messages
copied to user space, thus user space application needs to information
out of the structure to parse the content of structure.
This commit adds a field to express the number of messages copied to user
space since It is more preferable to use self-contained structure.
Kees Cook proposed an idea of annotation for bound of flexible arrays
in his future improvement for flexible-length array in kernel. The
additional field for message count is suitable to the idea as well.
Reference: https://people.kernel.org/kees/bounded-flexible-arrays-in-c
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230202133708.163936-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some motherboards have multiple HDA codecs connected to the serial bus.
The current code may create multiple mixer controls with the almost
identical identification.
The current code use id.device field from the control element structure
to store the codec address to avoid such clashes for multiple codecs.
Unfortunately, the user space do not handle this correctly. For mixer
controls, only name and index are used for the identifiers.
This patch fixes this problem to compose the index using the codec
address as an offset in case, when the control already exists. It is
really unlikely that one codec will create 10 similar controls.
This patch adds new kernel module parameter 'ctl_dev_id' to allow
select the old behaviour, too. The CONFIG_SND_HDA_CTL_DEV_ID Kconfig
option sets the default value.
BugLink: https://github.com/alsa-project/alsa-lib/issues/294
BugLink: https://github.com/alsa-project/alsa-lib/issues/205
Fixes: 54d1740315 ("[ALSA] hda-codec - Fix connection list parsing")
Fixes: 1afe206ab6 ("ALSA: hda - Try to find an empty control index when it's occupied")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230202092013.4066998-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The following series adds support for the PCM delay reporting in SOF core level
and implements the needed infrastructure with IPC4 to finally enable it for MTL.
Currently this is only supported on MTL (and via IPC4), but with the
infrastructure in place it will be possible to support other platforms with
DeepBuffer.
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
Today I came across two regressions in next with SOF:
The topology would not load with a failure of creating playback DAI
the first patch is fixing this which was caused by a missing 'else' in the patch
After fixing the topology loading, the module unloading caused kernel panic.
The second patch is correcting that which is I likely caused by copy-paste to
set wrong unload callback for the graph element.
With these patches applied SOF is working on next and modules can be unloaded
My randconfig build setup ran into a rare build failure with
CONFIG_SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE=y
CONFIG_SND_SOC_SOF_INTEL_SOUNDWIRE=m
CONFIG_SOUNDWIRE=y
CONFIG_SOUNDWIRE_INTEL=m
CONFIG_SND_SOC_SOF_HDA=y
CONFIG_SND_SOC_SOF_INTEL_TGL=y
x86_64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_init_caps':
hda.c:(.text+0x691): undefined reference to `sdw_intel_cnl_hw_ops'
x86_64-linux-ld: hda.c:(.text+0x6f2): undefined reference to `sdw_intel_probe'
x86_64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_sdw_startup':
hda.c:(.text+0x1c40): undefined reference to `sdw_intel_startup'
x86_64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_sdw_process_wakeen':
hda.c:(.text+0x1cb6): undefined reference to `sdw_intel_process_wakeen_event'
x86_64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_dsp_interrupt_thread':
hda.c:(.text+0x1d67): undefined reference to `sdw_intel_thread'
x86_64-linux-ld: sound/soc/sof/intel/hda.o: in function `hda_dsp_remove':
hda.c:(.text+0x2655): undefined reference to `sdw_intel_exit'
My best understanding is that the definition of
SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE was intended to avoid this
problem, but got it wrong for the SND_SOC_SOF_INTEL_SOUNDWIRE=m case,
where the 'select' is meant to set SOUNDWIRE_INTEL to the value of
SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE rather than the intersection of
SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE and SND_SOC_SOF_INTEL_SOUNDWIRE.
Change the condition to check for SND_SOC_SOF_INTEL_SOUNDWIRE to be a
boolean rather than a tristate expression in order to propagate this
as intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230202102247.806749-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Smatch static checker warning like below was found.
sound/soc/mediatek/mt8188/mt8188-dai-etdm.c:2487
mt8188_dai_etdm_parse_of()
warn: 'ret' returned from snprintf() might be larger than 48
2479 for (i = 0; i < MT8188_AFE_IO_ETDM_NUM; i++) {
2480 dai_id = ETDM_TO_DAI_ID(i);
2481 etdm_data = afe_priv->dai_priv[dai_id];
2482
2483 ret = snprintf(prop, sizeof(prop),
2484 "mediatek,%s-multi-pin-mode",
2485 of_afe_etdms[i].name);
2486 if (ret < 0) {
--> 2487 dev_err(afe->dev, "%s snprintf
err=%d\n",
2488
In linux kernel, snprintf() never returns negatives. On the other hand,
the format string like "mediatek,%s-multi-pin-mode" must be smaller
than sizeof(prop)=48.
After discussing in the mail thread[1], I remove the dead code to fix
the Smatch warnings.
[1]: https://lore.kernel.org/all/Y9EdBg641tJDDrt%2F@kili/
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230202103704.15626-1-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The delay function is used to calculate the difference
between hw_ptr and dai dma position. I2S, DMIC and SDW will
use dai dma position in shared SRAM window to calculate the
delay. HDaudio will retrieve dai dma position from host mmio memory
space since it doesn't support LLP counter reported by firmware.
In two cases dai dma position is inaccurate for delay calculation
(1) dai pipeline is started before host pipeline
(2) multiple streams mixed into one. Each stream has the same dai
dma position
Firmware calculates correct stream_start_offset for all cases including
above two. Driver subtracts stream_start_offset from dai dma position to
get accurate one.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Get HDaudio link position for current stream delay calculation
from hda registers.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM delay depends on stream position based on hardware
counter to calculate stream delay so add this ops to get
stream position according to hardware counter.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sof framework will call specific delay function for
different IPC version.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the hw_params to init time info for ipc4 delay calculation.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allocate time info when pcm is loaded by topology
and free it when pcm is unloaded by topology.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Start_stream_offset is used to strip invalid sample count in dai
for some cases like dai is started before host. llp_offset is used
to get current dai position from memory windows.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FW can share some information with host driver, .e.g fw status, pipeline
status and volume status. On ipc4 platform it is located in memory
windows 0 with size of struct sof_ipc4_fw_reg.
With this patch, ipc4 driver can find fw information in fw_info_box
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ipc4_fw_reg defines the content of memory window 0 shared by fw.
Host driver can get fw information by data structure defined in
this file.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230202132954.26773-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
../sound/soc/atmel/mchp-spdifrx.c:455:3: error: variable 'mr' is uninitialized when used here [-Werror,-Wuninitialized]
mr |= SPDIFRX_MR_ENDIAN_BIG;
^~
../sound/soc/atmel/mchp-spdifrx.c:432:8: note: initialize the variable 'mr' to silence this warning
u32 mr;
^
= 0
1 error generated.
Zero initialize mr so that these bitwise OR and assignment operation
works unconditionally.
Fixes: fa09fa6038 ("ASoC: mchp-spdifrx: fix controls which rely on rsr register")
Link: https://github.com/ClangBuiltLinux/linux/issues/1797
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230202-mchp-spdifrx-fix-uninit-mr-v1-1-629a045d7a2f@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As interrupts are Level-triggered,unless and until we deassert the register
the interrupts are generated which causes spurious interrupts unhandled.
Now we deasserted the interrupt at top half which solved the below
"nobody cared" warning.
warning reported in dmesg:
irq 80: nobody cared (try booting with the "irqpoll" option)
CPU: 5 PID: 2735 Comm: irq/80-AudioDSP
Not tainted 5.15.86-15817-g4c19f3e06d49 #1 1bd3fd932cf58caacc95b0504d6ea1e3eab22289
Hardware name: Google Skyrim/Skyrim, BIOS Google_Skyrim.15303.0.0 01/03/2023
Call Trace:
<IRQ>
dump_stack_lvl+0x69/0x97
__report_bad_irq+0x3a/0xae
note_interrupt+0x1a9/0x1e3
handle_irq_event_percpu+0x4b/0x6e
handle_irq_event+0x36/0x5b
handle_fasteoi_irq+0xae/0x171
__common_interrupt+0x48/0xc4
</IRQ>
handlers:
acp_irq_handler [snd_sof_amd_acp] threaded [<000000007e089f34>] acp_irq_thread [snd_sof_amd_acp]
Disabling IRQ #80
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20230203123254.1898794-1-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mario Limonciello <mario.limonciello@amd.com>:
It's been reported that a number of laptops have a low volume
level from the digital microphone compared to Windows.
AMD offers a register that can adjust the gain for PDM which is not
configured at maximum gain by default.
To fix this change the default for all 3 drivers to raise the gain
but also offer a module parameter. The module parameter can be used
for debugging if the gain is too high on a given laptop.
This is intentionally split into multiple patches for default and
parameter so that if the default really does behave better universally
we can bring it back to stable too later.
In case of regressions for any users that the new pdm_gain value is
too high and for additional debugging, introduce a module parameter
that would let them configure it.
This parameter should be removed in the future:
* If it's determined that the parameter is not needed, just hardcode
the correct value as before
* If users do end up using it to debug and report different values
we should introduce a config knob that can have policy set by ucm.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-7-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No issues have been reported yet for DMIC audio level on ps platforms,
but as problems were found both on YC (Rembrandt) and Renoir based
designs it's very likely they happen on ps too.
Increase the PDM gain to solve this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-6-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of regressions for any users that the new pdm_gain value is
too high and for additional debugging, introduce a module parameter
that would let them configure it.
This parameter should be removed in the future:
* If it's determined that the parameter is not needed, just hardcode
the correct value as before
* If users do end up using it to debug and report different values
we should introduce a config knob that can have policy set by ucm.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-5-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A similar issue that was reported on Rembrandt based laptops with
low DMIC volume is also being reported for Barcelo based laptops
that use renoir acp3x.
Increase the PDM gain to overcome this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-4-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of regressions for any users that the new pdm_gain value is
too high and for additional debugging, introduce a module parameter
that would let them configure it.
This parameter should be removed in the future:
* If it's determined that the parameter is not needed, just hardcode
the correct value as before
* If users do end up using it to debug and report different values
we should introduce a config knob that can have policy set by ucm.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-3-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A number of users for Lenovo Rembrandt based laptops are
reporting that the microphone is too quiet relative to
Windows with a dual boot.
Increase the PDM gain to overcome this problem.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230131184653.10216-2-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the control_unload for graph type of elem will lead surprises on
module unload.
The correct callback to use is the dapm_route_unload.
Fixes: 31e9273912 ("ASoC: topology: Use unload() op directly")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230201112846.27707-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion to use generic helpers missed the else for the dai
direction check which leads to failure when loading playback widgets
Fixes: 323f09a61d ("ASoC: sof: use helper function")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230201112846.27707-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A bit higher volume of changes than wished, but each change is
relatively small and the fix targets are mostly device-specific,
so those should be safe as a late stage merge.
The most significant LoC is about the memalloc helper fix, which
is applied only to Xen PV. The other major parts are ASoC Intel
SOF and AVS fixes that are scattered as various small code
changes. The rest are device-specific fixes and quirks for HD-
and USB-audio, FireWire and ASoC AMD / HDMI.
-----BEGIN PGP SIGNATURE-----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=/+Up
-----END PGP SIGNATURE-----
Merge tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit higher volume of changes than wished, but each change is
relatively small and the fix targets are mostly device-specific, so
those should be safe as a late stage merge.
The most significant LoC is about the memalloc helper fix, which is
applied only to Xen PV. The other major parts are ASoC Intel SOF and
AVS fixes that are scattered as various small code changes. The rest
are device-specific fixes and quirks for HD- and USB-audio, FireWire
and ASoC AMD / HDMI"
* tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: firewire-motu: fix unreleased lock warning in hwdep device
ALSA: memalloc: Workaround for Xen PV
ASoC: cs42l56: fix DT probe
ASoC: codecs: wsa883x: correct playback min/max rates
ALSA: hda/realtek: Add Acer Predator PH315-54
ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022 into DMI table
ALSA: hda: Do not unset preset when cleaning up codec
ASoC: SOF: sof-audio: prepare_widgets: Check swidget for NULL on sink failure
ASoC: hdmi-codec: zero clear HDMI pdata
ASoC: SOF: ipc4-mtrace: prevent underflow in sof_ipc4_priority_mask_dfs_write()
ASoC: Intel: sof_ssp_amp: always set dpcm_capture for amplifiers
ASoC: Intel: sof_nau8825: always set dpcm_capture for amplifiers
ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
ALSA: hda/realtek: fix mute/micmute LEDs, speaker don't work for a HP platform
ASoC: SOF: keep prepare/unprepare widgets in sink path
ASoC: SOF: sof-audio: skip prepare/unprepare if swidget is NULL
ASoC: SOF: sof-audio: unprepare when swidget->use_count > 0
...
The ucb1400 MFD driver and its gpio and touchscreen child
drivers were only used on a few PXA machines that were unused
for a while and are now removed.
Removing these leaves the AC97 support as ALSA specific,
no other drivers are now connected through this interface.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Lee Jones <lee@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most PXA/MMP boards were removed, so the board specific ASoC
support is no longer needed, leaving only support for DT
based ones, as well as the "gumstix" and "spitz" machines
that may get converted to DT later.
Cc: Ian Molton <spyro@f2s.com>
Cc: Ken McGuire <kenm@desertweyr.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Both the DAC and ADC have digital gain controls available
for their mixers, which go from -31 to 0db by step of 1db.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Link: https://lore.kernel.org/r/20230122210703.2552384-1-cbranchereau@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Samsung Galaxy Book2 Pro 360 (13" 2022 NP930QED-KA1FR) with codec SSID
144d:ca03 requires the same workaround for enabling the speaker amp
like other Samsung models with ALC298 codec.
Cc: <stable@vger.kernel.org>
Signed-off-by: Guillaume Pinot <texitoi@texitoi.eu>
Link: https://lore.kernel.org/r/20230129171338.17249-1-texitoi@texitoi.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This loop accidentally reuses the "i" iterator for both the inside and
the outside loop. The value of MAX_STREAM_BUFFER is 5. I believe that
chip->rmh.stat_len is in the 2-12 range. If the value of .stat_len is
4 or more then it will loop exactly one time, but if it's less then it
is a forever loop.
It looks like it was supposed to combined into one loop where
conditions are checked.
Fixes: 8e6320064c ("ALSA: lx_core: Remove useless #if 0 .. #endif")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y9jnJTis/mRFJAQp@kili
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is tested on V4H White Hawk + ARD-AUDIO-DA7212
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7qe5ej5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch tidyups rsnd_dma_probe(), but there is no effect.
This is prepare for Gen4 support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r0va5elq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG need to know output rate of 44.1kHz/48kHz.
It is using single variable for each, but this patch changes
it to array. Nothing is changed by this patch.
This is prepare for R-Car Gen4 support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tu065em3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg.c is assuming number of clkin/clkout are fixed, but it is
not correct on Gen4. This patch uses clkin/out_size to handling it.
This is prepare for R-Car Gen4 support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8km5em7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves clkout_name to top of the file to handling both
clkin/clkout in the same place.
This is prepare for R-Car Gen4 support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87wn525emc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg.c is usig "clk" as clock IN, but is using "clkout" for
clock OUT. This patch arranges "clk" to "clkin".
This is prepare for R-Car Gen4 support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y1pi5emh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The flag LRCLK_ASYNC / AUDIO_OUT_48 had been added to handling
special case of Salvator-X board, but it is not used on upstream.
It makes code complex today, let's remove these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zg9y5emm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SoC can't handle all requested hw rule. In such case, it will indicate
like below, but it is unclear why it didn't work to user.
This patch indicates warning in such case once, because player will try to
similar rule many times.
# aplay sound.wav
Playing WAVE 'sound.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
aplay: aplay.c: 1359: set_params: Assertion `err >= 0' failed.
Aborted by signal Aborted...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87357q6t7b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_master_clk_start() indicates error message if it couldn't
handle requested clock/rate, but it is not caring all cases.
This patch cares it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874js66t7g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b43b8ae87c ("ASoC: rsnd: protect mod->status") removed
RSND_DEBUG_NO_DAI_CALL and rsnd_dbg_dai_call(), but these are still
exist on rsnd.h. This patch removes it.
Fixes: b43b8ae87c ("ASoC: rsnd: protect mod->status")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875ycm6t7l.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1f9c82b5ab ("ASoC: rsnd: add debugfs support") added
CONFIG_DEBUG_FS related definitions on rsnd.h, but it should be
added inside of RSND_H. This patch fixup it.
Fixes: 1f9c82b5ab ("ASoC: rsnd: add debugfs support")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877cx26t7r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd sets "channels_min" which is used from
snd_soc_dai_stream_valid() without checking DT playback/capture property.
Thus, "aplay -l" or "arecord -l" will indicate un-exising device.
This patch checks DT proerty and do nothing playback/capture settings if
not exist.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878rhi6t7x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set driver name to allow matching different UCM2 configurations
for the multiple devices sharing the same APQ8096 ASoC.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20220622061106.35071-1-y.oudjana@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
The CS42L42 has a SoundWire interface for control and audio. This
chain of patches adds support for this.
Patches #1 .. #5 split out various changes to the existing code that
are needed for adding Soundwire. These are mostly around clocking and
supporting the separate probe and enumeration stages in SoundWire.
Patches #6 .. #8 actually adds the SoundWire handling.
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
struct snd_soc_dai need to have info for playback/capture,
but it is using "playback/capture_xxx" or "tx/tx_xxx" or array.
This kind of random definition is very difficult to read.
This patch-set add helper functions and each driver use it.
And cleanup the definition.
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
This series adds runtime PM support for Microchip SPDIFRX driver.
Along with it I added few fixes identified while going though the code
and playing with Microchip SPDIFRX controller.
Merge series from wangweidong.a@awinic.com:
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost converter.
Add a DT schema for describing Awinic AW88395 audio amplifiers. They are
controlled using I2C
Merge series from Herve Codina <herve.codina@bootlin.com>:
The Renesas IDT821034 codec is four channel PCM codec with on-chip
filters and programmable gain setting. It also provides SLIC
(Subscriber Line Interface Circuit) signals as GPIOs.
Since clock stop causes bus reset on Intel controllers, we need
to wait for the debounce interval on resume, to ensure all the
interrupt status registers are set correctly.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-9-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
idle_bias_on was set because cs42l42 has a "VMID" type pseudo-midrail
supply (named FILT+), and these typically take a long time to charge.
But the driver never enabled pm_runtime so it would never have powered-
down the cs42l42 anyway.
In fact, FILT+ can charge to operating voltage within 12.5 milliseconds
of enabling HP or ADC. This time is already covered by the startup
delay of the HP/ADC.
The datasheet warning about FILT+ taking up to 1 second to charge only
applies in the special cases that either the PLL is started or
DETECT_MODE set to non-zero while both HP and ADC are off. The driver
never does either of these.
Removing idle_bias_on allows the Soundwire host controller to suspend
if there isn't a snd_soc_jack handler registered.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-8-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for using CS42L42 as a SoundWire device.
SoundWire-specifics are kept separate from the I2S implementation as
much as possible, aiming to limit the risk of breaking the I2C+I2S
support.
There are some important differences in the silicon behaviour between
I2S and SoundWire mode that are reflected in the implementation:
- ASP (I2S) most not be used in SoundWire mode because the two interfaces
share pins.
- The SoundWire capture (record) port only supports 1 channel. It does
not have left-to-right duplication like the ASP.
- DP2 can only be prepared if the HP has powered-up. DP1 can only be
prepared if the ADC has powered-up. (This ordering restriction does
not exist for ASPs.) The SoundWire core port-prepare step is
triggered by the DAI-link prepare(). This happens before the
codec DAI prepare() or the DAPM sequence so these cannot be used
to enable HP/ADC. Instead the HP/ADC enable/disable are done during
the port_prep callback.
- The SRCs are an integral part of the audio chain but in silicon their
power control is linked to the ASP. There is no equivalent power link
to SoundWire DPs so the driver must take "manual" control of SRC power.
- The SoundWire control registers occupy the lower part of the SoundWire
address space so cs42l42 registers are offset by 0x8000 (non-paged) in
SoundWire mode.
- Register addresses are 8-bit paged in I2C mode but 16-bit unpaged in
SoundWire.
- Special procedures are needed on register read/writes to (a) ensure
that the previous internal bus transaction has completed, and
(b) handle delayed read results, when the read value could not be
returned within the SoundWire read command.
There are also some differences in driver implementation between I2S
and SoundWire operation:
- CS42L42 I2S does not runtime_suspend, but runtime_suspend/resume support
has been added into the driver in SoundWire mode as the most convenient
way to power-up the bus manager and to handle the unattach_request
condition, though the CS42L42 chip does not itself suspend or resume.
- Intel SoundWire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This means that the
interrupt registers will be reset in between the interrupt being
generated and the interrupt being handled, and since the interrupt
status is debounced, these values may not be accurate immediately,
and may cause spurious unplug events before settling.
- As in I2S mode, the PLL is only used while audio is active because
of clocking quirks in the silicon. For SoundWire the cs42l42_pll_config()
is deferred until the DAI prepare(), to allow the cs42l42_bus_config()
callback to set the SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-7-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Export functions that will be needed by a SoundWire module.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-6-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup of the ASP (audio serial port) was being done as a side-effect of
cs42l42_pll_config() and forces a restriction on the ratio of sample_rate
to bit_clock that is invalid for Soundwire.
Move the ASP setup into a dedicated function.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The chosen clocking configuration must give an internal MCLK (MCLKint)
that is an integer multiple of the sample rate.
On I2S each of the supported bit clock frequencies can only be generated
from one sample rate group (either the 44100 or the 48000) so the code
could use only the bitclock to look up a PLL config.
The relationship between sample rate and bitclock frequency is more
complex on Soundwire and so it is possible to set a frame shape to
generate a bitclock from the "wrong" group. For example 2*147 with a
48000 sample rate would give a bitclock of 14112000 which on I2S
could only be derived from a 44100 sample rate.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOFT_RESET_REBOOT register is needed to recover CS42L42 state after
a Soundwire bus reset.
This is required to be set whenever there is severe/hard bus reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230127165111.3010960-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current snd_soc_dai has data for Playback/Capture, but it is very
random. Someone is array (A), someone is playback/capture (B),
and someone is tx/rx (C);
struct snd_soc_dai {
...
(A) unsigned int stream_active[SNDRV_PCM_STREAM_LAST + 1];
(B) struct snd_soc_dapm_widget *playback_widget;
(B) struct snd_soc_dapm_widget *capture_widget;
(B) void *playback_dma_data;
(B) void *capture_dma_data;
...
(C) unsigned int tx_mask;
(C) unsigned int rx_mask;
};
Because of it, the code was very complicated.
This patch creates new data structure to merge these into one,
and tidyup the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87cz6vea1v.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87fsbrea25.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87ilgnea2p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87k013ea2u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/87r0vbea3r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has many helper function.
This patch use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/87sffrea3z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch static analysis tool detects that acquired lock is not released
in hwdep device when condition branch is passed due to no event. It is
unlikely to occur, while fulfilling is preferable for better coding.
Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: 634ec0b290 ("ALSA: firewire-motu: notify event for parameter change in register DSP model")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230130141540.102854-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function local variable, curr_cycle_time is declared without
initialization. When tracepoints event is not probed, it looks to be
used as is. This commit fixes it. Fortunately, the value of local variable
is not used unless the event is probed, thus this commit is for better
coding.
Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: fef4e61b0b ("ALSA: firewire-lib: extend tracepoints event including CYCLE_TIME of 1394 OHCI")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230130141532.102838-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Following is series of fixes and cleanups for core topology code. Few
patches fixing various problems all around and few fixing function
names.
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-5-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-4-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-3-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Awinic AW88395 is an I2S/TDM input, high efficiency
digital Smart K audio amplifier with an integrated 10.25V
smart boost convert
Signed-off-by: Nick Li <liweilei@awinic.com>
Signed-off-by: Bruce zhao <zhaolei@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230113055301.189541-2-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Renesas IDT821034 codec is four channel PCM codec with on-chip
filters and programmable gain setting.
It also provides SLIC (Subscriber Line Interface Circuit) signals as
GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230126085137.375814-3-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for Microchip SPDIFRX driver. On runtime suspend
the clocks are disabled and regmap is set in caching mode. On runtime
resume the clocks are enabled and regmap is synced with the device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-8-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
CSC interrupts which might be used in controls are on bits 8 and 9 of
SPDIFRX_IDR register. Thus disable all the interrupts that are exported
by driver.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-5-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel status get and channel subcode get controls relies on data
returned by controls when certain IRQs are raised. To achieve that
completions are used b/w controls and interrupt service routine. The
concurrent accesses to these controls are protected by
struct snd_card::controls_rwsem.
Issues identified:
- reinit_completion() may be called while waiting for completion
which should be avoided
- in case of multiple threads waiting, the complete() call in interrupt
will signal only one waiting thread per interrupt which may lead to
timeout for the others
- in case of channel status get as the CSC interrupt is not refcounted
ISR may disable interrupt for threads that were just enabled it.
To solve these the access to controls were protected by a mutex. Along
with this there is no need for spinlock to protect the software cache
reads/updates b/w controls and ISR as the update is happening only when
requested from control, and only one reader can reach the control.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_interruptible_timeout() returns 0 in case of
timeout. Check this into account when returning from function.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPDIFRX block is clocked by 2 clocks: peripheral and generic clocks.
Peripheral clock feeds user interface (registers) and generic clock feeds
the receiver.
To enable the receiver the generic clock needs to be enabled and also the
ENABLE bit of MCHP_SPDIFRX_MR register need to be set.
The signal control exported by mchp-spdifrx driver reports wrong status
when the receiver is disabled. This can happen when requesting the signal
and the capture was not previously started. To solve this the receiver
needs to be enabled (by enabling generic clock and setting ENABLE bit of
MR register) before reading the signal status.
As with this fix there are 2 paths now that need to control the generic
clock and ENABLE bit of SPDIFRX_MR register (one path though controls, one
path though configuration) a mutex has been introduced. We can't rely on
subsystem locking as the controls are protected by
struct snd_card::controls_rwsem semaphore and configuration is protected
by a different lock (embedded in snd_pcm_stream_lock_irq()).
The introduction of mutex is also extended to other controls which rely on
SPDIFRX_RSR.ULOCK bit as it has been discovered experimentally that having
both clocks enabled but not the receiver (through ENABLE bit of SPDIFRX.MR)
leads to inconsistent values of SPDIFRX_RSR.ULOCK. Thus on some controls we
rely on software state (dev->trigger_enabled protected by mutex) to
retrieve proper values.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_soc_dobj only needs pointer to the unload function, instead
however, there is pointer to all topology operations. Change code to use
the function pointer instead of pointer to structure containing all
operations.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-12-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions removing bytes, enum and mixer kcontrols are identical. Unify
them under one function and use it to free associated kcontrols.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-11-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Caller already checks if hdr_pos is behind EOF, before calling
soc_tplg_valid_header(), so there is no need to recheck it again. This
also allows to remove behaviour of return 0 - forcing the caller to
break out of while loop.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-10-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Function soc_tplg_dapm_complete() detects an error and logs it, but
doesn't return failure to the caller, fix it by returning the error.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-9-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing address of structure, the containing structure is
cast to target structure. While it works - the expected structure is the
first field of containing one - it is bad practice, fix this by passing
pointer to structure field.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-8-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to forward declare functions if their use is after
their definition.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Those are the only functions missing soc_tplg_ prefix, add it for
consistency.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions other than soc_valid_header have soc_tplg_ prefix. Rename
function to follow convention in file.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology is being abbreviated to "tplg", not "tplc", however, few
functions have typo in name, fix it.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The constant is unused, so it can be safely removed.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230127231111.937721-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the reserved bit 7 in the ANALOG_CTRL_REG for the TAS5720A-Q1 device,
when probing.
The datasheet mentions that the bit should be 1 during reset/powerup.
The device did not initialize before setting this value to 1. So, this
could be a quirk of this device. Or it could be a quirk with the board on
which it was tested.
That is why this patch is separate from the patch that adds support for the
TAS5720A-Q1 device.
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-3-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds support the TAS5720A-Q1 audio codec, in the same driver as
tas5720.
Functionally, this driver is pretty similar to it's TAS5720x variant.
The first 3 registers are the same, so the main control and device
identification can happen with these registers.
The next registers differ.
This variant offers control (in the registers) for 2 speakers, which is
implemented here (in a basic manner).
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-2-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to be re-used in tas5720_mute() (which is part of the dai_ops) and
also in the tas5720_fault_check_work() hook.
The benefit here isn't too great (now).
It's only when we add support for a new device with a slightly different
regmap that this becomes more useful.
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor bit width calculation using params_physical_width()
instead hard-code values.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230130100104.4076640-1-venkataprasad.potturu@amd.com
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
../sound/soc/kirkwood/kirkwood-dma.c: In function
'kirkwood_dma_conf_mbus_windows.constprop':
../sound/soc/kirkwood/kirkwood-dma.c:90:24: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
90 | if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
| ~~^~~~~~
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230127224128.never.410-kees@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The following series will enable multi-stream support for playback and capture
streams.
Currently only a single PCM can be connected to a DAI, with the multi-stream
support it is possible to connect multiple PCMs to a single DAI.
To achieve this we need to make sure that DAIs/AIF are only set up once since
other stream could be connected to it later.
We also need to introduce reference or use counting for widgets to make sure
that they are not going to be destroyed while other streams are still using
them.
With the multi-stream support we also need to extend our current locking scheme
which worked well for simple paths.
Merge series from Astrid Rost <astrid.rost@axis.com>:
Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.
Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
An unfortunately large batch of fixes here, the numbers amplified
by several repeated fixes for patterns of bugs in multiple
drivers. Most of this is in the x86 drivers which are very
actively developed, the implementation of PCI shutdown is a fix
for issues with spamming warnings into the logs with a leaked
reference to the i915 driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmPT/JAACgkQJNaLcl1U
h9BGFQf/dg3Ra5I9QQBB/HI+3Psmsocg4aNb9AqOoOAapGvDSwiJpN8N9s0iBdkr
X/W4w87DG0zx5yGXciXSNMk3zueAGiZu79nEan4wB62qkICDTxO/TkdhXkSHtURl
r8vJGUvWwsD1Cw4+lYrzmB4kH+YDjTddS2Z/Ejq2DfTqeQRtxntVVueN84BHQ877
drl8PWhPnqCxoiKsBo7LBvZnVsZkPYMGAczcwQhmJBjE0Ysvp5yWoS0IuOCw9WL3
kwRh86Fr400ipWEsbkzn/a/wIc1nfBxGWbjiTUIS0iLIWAyAOOFCbUCNAmoS94A/
9j6+PXdS4pLkKmreNsAXSpkFoutbjA==
=iqU1
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.2-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.2
An unfortunately large batch of fixes here, the numbers amplified
by several repeated fixes for patterns of bugs in multiple
drivers. Most of this is in the x86 drivers which are very
actively developed, the implementation of PCI shutdown is a fix
for issues with spamming warnings into the logs with a leaked
reference to the i915 driver.
The uevent() callback in struct bus_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.
Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-3-astrid.rost@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function to return the jack type of snd_jack_types.
This allows a generic card driver to add a jack with the specified
type.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-2-astrid.rost@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pipeline setup fails at the first widget/pipeline then we will have
no spipe stored under the pipeline_list->pipelines, the
pipeline_list->count is 0.
If this is the case we would have a NULL pointer dereference if the
execution is allowed to proceed.
Check for this condition along with the pipeline_list->pipelines check
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-19-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The use_count of the swidget is protect by ALSA core PCM locking with the
exception when an associated kcontrol is changed.
It has been observed that a rightly timed kcontrol access during stream
stop can result of an attempt to send a control update to a widget which
has been freed up between the check of the use_count and the message
sending.
We need to protect the entire sof_widget_setup() and sof_widget_free()
execution to make it safe to rely on the use_count.
Move the code under an _unlocked() function and use a mutex to protect
the execution of the functions for concurrency.
On the control path we need to use the lock only for the kcontrol access,
the widget_kcontrol_setup() op is called with the lock already held.
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-18-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_widget_free() on the error path will decrement the use count and if
we jump to widget_free: then the use_count will be decremented by two,
which is not correct as we only incremented once with 1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-17-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting/stopping multiple streams in parallel, pipeline triggers
and pipeline frees can get interleaved. So use the same mutex used for
pipeline trigger to protect the pipeline frees as well. Rename the
trigger_mutex to pipeline_state_mutex for more clarity.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the started_count and paused_count to implement reference counting
when making decisions to start/stop/pause pipelines during the FE DAI
trigger. This is necessary to trigger the shared pipelines in the FE DAI
trigger properly.
With IPC4, the FE trigger will issue multiple pipeline state changes,
and the triggers are propagated downstream to connected pipelines by
the SOF driver - not the firmware. This creates a window for race
conditions where an FE trigger preempts another one, which results
in inconsistent pipeline states and refcounts.
This patch introduces a mutex lock for the pcm trigger that guarantees
that IPC4 state and resources are accessed in a serialized manner.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-15-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For more clarity, rename the struct ipc4_pipeline_set_state_data
variable to trigger_list instead of data. No functionality change.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-14-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce struct snd_sof_pipeline to save the information about
pipelines including the pipeline widget, their status wrt how many PCM's
are using them and whether they are complete or not.
In struct snd_sof_widget, replace pipe_widget with spipe and remove
complete. In struct snd_sof_pcm_stream_pipeline_list, replace
pipe_widgets with pipelines.
Update all users accordingly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the list of pipelines in the PCM stream's pipeline info to trigger
the pipelines in the right order. Add a helper for triggering pipelines
in batch mode that will be used to trigger multiple pipelines at the
same time.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Populate the pipeline_info for the PCM stream with the list of pipeline
widgets that need to be handled during the PCM trigger. This will be
used in the IPC-specific PCM trigger op to trigger the pipelines.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new flag, skip_during_fe_trigger, to struct sof_ipc4_pipeline to
skip triggering pipelines in the FE DAI trigger. Set this flag for the
HDA DAI BE pipelines so that their BE pipeline will not be triggered in
the FE DAI trigger. Also, move the trigger handling for all commands
include START/PAUSE_RELEASE for the HDA DAI's to the backend DAI trigger
ops.
For the SSP/DMIC/SDW cases, remove the BE DAI trigger as they involve no
DMA operations and can be triggered in the FE DAI trigger. This is in
preparation to perform batch triggering of all pipelines for the non-HDA
case.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the pcm_setup/pcm_free ops for IPC4. Define a new struct
snd_sof_pcm_stream_trigger_info and add a new field trigger_info of this
type to struct snd_sof_pcm_stream. This will be used to save the list of
pipelines that need to be triggered.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These will be used to perform IPC-specific PCM setup/free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new topology IPC op to set up DAI links and set the link trigger
order to match the expectation based on the IPC type. Note that the
link_setup op implementations for IPC3 and IPC4 are not identical and
have contrasting trigger orders for playback and capture.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
IPC3 and IPC4 have different requirements for the order in which the FE
CPU and BE CPU DAI trigger callbacks must be invoked. With a regular PCM
start/stop, pipeline widgets are set up during hw_params and freed
during hw_free.
But when the system is suspended when a PCM is running,
pipeline widgets are freed during the SUSPEND trigger callback for the
FE CPU DAI. In order to avoid freeing the pipeline widgets before the BE
CPU DAI trigger is executed, the trigger order was modified in previous
contributions in the PCM dai_link_fixup callback to make sure that the BE
CPU DAI trigger stop/suspend is always invoked before the FE CPU DAI
trigger. But this contradicts the firmware requirement for IPC4 w.r.t.
ordering of pipeline triggers.
So, remove the freeing of pipeline widgets during FE CPU DAI suspend
trigger and handle it during system suspend when the
tear_down_all_pipelines() IPC op is invoked. This will be followed up
with a patch to fix the trigger order for IPC4.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When walking the list of the widgets from the source to the sink, we
accidentally also end up preparing/setting up the widgets that are not
in the list of connected DAPM widgets associated with the PCM. Avoid
this by checking if a widget is part of the connected DAPM widget list
during widget prepare, unprepare, setup or free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling the sof_widget_setup/free() for the DAI/AIF widgets inside the
snd_soc_dapm_widget_for_each_sink_path() loop will end up setting up or
freeing the widget multiple times if there are multiple paths leaving
the widget. Fix this by moving the widget setup/free for the starting
widget in each path outside the loop.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Export the widget_in_list() function to be used by other modules.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
