On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent support for the multiple PCM devices allowed user to use
multiple HDMI/DP outputs, but at the same time, the PCM stream
assignment has been changed, too. Due to that, the former PCM#0
(there was only one stream in the past) is likely assigned to a
different one (e.g. PCM#2), and it ends up with the regression when
user sticks with the fixed configuration using the device#0.
Although the multiple monitor support shouldn't matter when user
deploys the backend like PulseAudio that checks the jack detection
state, the behavior change isn't always acceptable for some users.
As a mitigation, this patch introduces an option to switch the
behavior back to the old-good-days: when the new option,
single_port=1, is passed, the driver creates only a single PCM device,
and it's assigned to the first connected one, like the earlier
versions did. The option is turned off as default still to support
the multiple monitors.
Fixes: 8a2d6ae1f7 ("ALSA: x86: Register multiple PCM devices for the LPE audio card")
Reported-and-tested-by: Hubert Mantel <mantel@metadox.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Reported-by: 范龙飞 <long7573@126.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some more devices that need quirks to handle DSD modes correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-and-tested-by: Thomas Gresens <tgresens@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The layout of the UAC2 Control request and response varies depending on
the request type. With the current implementation, only the Layout 2
Parameter Block (with the 2-byte sized RANGE attribute) is handled
properly. For the Control requests with the 1-byte sized RANGE attribute
(Bass Control, Mid Control, Tremble Control), the response is parsed
incorrectly.
This commit:
* fixes the wLength field value in the request
* fixes parsing the range values from the response
Fixes: 23caaf19b1 ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirk to ensure a sync endpoint is properly configured.
This patch is a fix for same symptoms on Behringer UFX1204 as patch
from Albertto Aquirre on Dec 8 2016 for Axe-Fx II.
Signed-off-by: Lassi Ylikojola <lassi.ylikojola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AC97_BUS_NEW Kconfig symbol selects the globally undefined symbol
AC97.
Robert Jarzmik confirmed in https://lkml.org/lkml/2018/2/7/96 that the
select was put in by mistake and can be safely removed, with no other
changes required. Remove it.
Fixes: 74426fbff6 ("ALSA: ac97: add an ac97 bus")
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the merge window having been delayed for another week here's
another batch of updates that came in during that week. There's a few
important fixes in here, mainly a fix for I/O on a number of devices
caused by some of the component rework and a fix for a potential issue
if more than one component in a link provides compressed operations.
The I/O fixes are particularly important as the problem causes a power
regression on a number of OMAP platforms.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlp65E4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Oy1B/9XQd6twiSRfNKtbdujOyvjc8lpZ01n
JYHVySXyL9ZqAnIblM7Or/iXVEtsAVcXgFegF3SLHAY6VF7DQ1pDolnxUtuXOxOj
j+/2Y4wnDGCjXEr0tMoxrbNUIqlVZLCpPwsPo3vvVbr6sLLmQYVposNp2A2sK2bz
uWm9E3Nr26Q0UctzjWQM5+AFHSouyL7zDPfBCoWkEToP7163w6r4JDr991KdNGwP
Ac+5qjRUSldsn8WB2ngm8ioqbq+aOvsz2THYjG8gxrlQK+BWsyCDqF7f1d9GWse2
7k+xZLrdJrVkBMOnpvOx/Y4KRfe9BAFZBZ3KRbi2IR++7TD3902xEX27
=aIRm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound
Pull more ASoC updates from Mark Brown:
"With the merge window having been delayed for another week here's
another batch of updates that came in during that week.
There's a few important fixes in here, mainly a fix for I/O on a
number of devices caused by some of the component rework and a fix for
a potential issue if more than one component in a link provides
compressed operations. The I/O fixes are particularly important as the
problem causes a power regression on a number of OMAP platforms"
* tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound: (22 commits)
ASoC: stm32: add of dependency for stm32 drivers
ASoC: mt8173-rt5650: fix child-node lookup
ASoC: dapm: fix debugfs read using path->connected
ASoC: compress: Fixup error messages
ASoC: compress: Remove some extraneous blank lines
ASoC: compress: Correct handling of copy callback
ASoC: Intel: kbl: Enable mclk and ssp sclk early
ASoC: Intel: Skylake: Add extended I2S config blob support in Clock driver
ASoC: Intel: Skylake: Add ssp clock driver
ASoC: Fix twl4030 and 6040 regression by adding back read and write
ASoC: sun8i-codec: Add ADC support for a33
ASoC: rockchip: Use dummy_dai for rt5514 dsp dailink
ASoC: soc-pcm: rename .pmdown_time to .use_pmdown_time for Component
ASoC: ak4613: call dummy write for PW_MGMT1/3 when Playback
ASoC: soc-pcm: don't call flush_delayed_work() many times in soc_pcm_private_free()
ASoC: soc-core: snd_soc_rtdcom_lookup() cares component driver name
ASoC: sam9x5_wm8731: Drop 'ASoC' prefix from error messages
ASoC: sam9g20_wm8731: use dev_*() logging functions
ASoC: max98373 Changed SPDX header in C++ comments style
ASoC: dmic: Fix check of return value from read of 'num-channels'
...
Add of dependency for STM32 ASoC drivers.
DFSDM of dependency is already inherited
from STM32_DFSDM_ADC dependency.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver used the wrong OF-helper when looking up the optional
capture-codec child node during probe. Instead of searching just
children of the sound node, a tree-wide depth-first search starting at
the unrelated platform node was done. Not only could this end up
matching an unrelated node or no node at all; the platform node could
also be prematurely freed since of_find_node_by_name() drops a reference
to its first argument. This particular pattern has been observed leading
to crashes after probe deferrals in other drivers.
Fix this by dropping the broken call to of_find_node_by_name() and
keeping only the second, correct lookup using of_get_child_by_name()
while taking care not to bail out if the optional node is missing.
Note that this also addresses two capture-codec node-reference leaks
(one for each of the original helper calls).
Compile tested only.
Fixes: d349caeb05 ("ASoC: mediatek: Add second I2S on mt8173-rt5650 machine driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fix a bug in dapm_widget_power_read_file(),
where it may sent opposite order of source/sink widget
into the p->connected().
for example,
static int connected_check(source, sink);
{"w_sink", NULL, "w_source", connected_check}
the dapm_widget_power_read_file() will query p->connected()
in following case
p->conneted("w_source", "w_sink")
p->conneted("w_sink", "w_source")
we should avoid the last case, since it's the wrong order (source/sink)
as declared in snd_soc_dapm_route.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thinkpad Dock device support for ALC298 platform.
It need to use SSID for the quirk table.
Because IdeaPad also has ALC298 platform.
Use verb for the quirk table will confuse.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform had two Dmic and single Dmic.
This update was for single Dmic.
This commit was for two Dmic.
Fixes: 75ee94b20b ("ALSA: hda - fix headset mic problem for Dell machines...")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One of them has the codec of alc256 and the other one has the codec
of alc289.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Pull misc vfs updates from Al Viro:
"All kinds of misc stuff, without any unifying topic, from various
people.
Neil's d_anon patch, several bugfixes, introduction of kvmalloc
analogue of kmemdup_user(), extending bitfield.h to deal with
fixed-endians, assorted cleanups all over the place..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
dcache: delete unused d_hash_mask
dcache: subtract d_hash_shift from 32 in advance
fs/buffer.c: fold init_buffer() into init_page_buffers()
fs: fold __inode_permission() into inode_permission()
fs: add RWF_APPEND
sctp: use vmemdup_user() rather than badly open-coding memdup_user()
snd_ctl_elem_init_enum_names(): switch to vmemdup_user()
replace_user_tlv(): switch to vmemdup_user()
new primitive: vmemdup_user()
memdup_user(): switch to GFP_USER
eventfd: fold eventfd_ctx_get() into eventfd_ctx_fileget()
eventfd: fold eventfd_ctx_read() into eventfd_read()
eventfd: convert to use anon_inode_getfd()
nfs4file: get rid of pointless include of btrfs.h
uvc_v4l2: clean copyin/copyout up
vme_user: don't use __copy_..._user()
usx2y: don't bother with memdup_user() for 16-byte structure
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull timer updates from Thomas Gleixner:
"The timer departement presents:
- A rather large rework of the hrtimer infrastructure which
introduces softirq based hrtimers to replace the spread of
hrtimer/tasklet combos which force the actual callback execution
into softirq context. The approach is completely different from the
initial implementation which you cursed at 10 years ago rightfully.
The softirq based timers have their own queues and there is no
nasty indirection and list reshuffling in the hard interrupt
anymore. This comes with conversion of some of the hrtimer/tasklet
users, the rest and the final removal of that horrible interface
will come towards the end of the merge window or go through the
relevant maintainer trees.
Note: The top commit merged the last minute bugfix for the 10 years
old CPU hotplug bug as I wanted to make sure that I fatfinger the
merge conflict resolution myself.
- The overhaul of the STM32 clocksource/clockevents driver
- A new driver for the Spreadtrum SC9860 timer
- A new driver dor the Actions Semi S700 timer
- The usual set of fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
usb/gadget/NCM: Replace tasklet with softirq hrtimer
ALSA/dummy: Replace tasklet with softirq hrtimer
hrtimer: Implement SOFT/HARD clock base selection
hrtimer: Implement support for softirq based hrtimers
hrtimer: Prepare handling of hard and softirq based hrtimers
hrtimer: Add clock bases and hrtimer mode for softirq context
hrtimer: Use irqsave/irqrestore around __run_hrtimer()
hrtimer: Factor out __hrtimer_next_event_base()
hrtimer: Factor out __hrtimer_start_range_ns()
hrtimer: Remove the 'base' parameter from hrtimer_reprogram()
hrtimer: Make remote enqueue decision less restrictive
hrtimer: Unify remote enqueue handling
hrtimer: Unify hrtimer removal handling
hrtimer: Make hrtimer_force_reprogramm() unconditionally available
hrtimer: Make hrtimer_reprogramm() unconditional
hrtimer: Make hrtimer_cpu_base.next_timer handling unconditional
hrtimer: Make the remote enqueue check unconditional
hrtimer: Use accesor functions instead of direct access
hrtimer: Make the hrtimer_cpu_base::hres_active field unconditional, to simplify the code
hrtimer: Make room in 'struct hrtimer_cpu_base'
...
The error message prints are a little inconsisent, tidy them up to be a
little more consistent with current style recommendations.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The soc_compr_copy callback is currently broken. Since the
changes to move the compr_ops over to the component the return
value is not correctly propagated, always returning zero on
success rather than the number of bytes copied. This causes
user-space to stall continuously reading as it does not believe
it has received any data.
Furthermore, the changes to move the compr_ops over to the
component iterate through the list of components and will call
the copy callback for any that have compressed ops. There isn't
currently any consensus on the mechanism to combine the results
of multiple copy callbacks.
To fix this issue for now halt searching the component list when
we locate a copy callback and return the result of that single
callback. Additional work should probably be done to look at the
other ops, tidy things up, and work out if we want to support
multiple components on a single compressed, but this is the only
fix required to get things working again.
Fixes: 9e7e3738ab ("ASoC: snd_soc_component_driver has snd_compr_ops")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
rt5663 needs mclk/sclk early to synchronize its internal clocks. Enable
these clocks early.
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extended I2S config blob supports multiple mclk dividers in NHLT blob.
This patch detects whether the I2S blob is legacy or extended based on the
signature value and chooses the mclk source and divider accordingly.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For certain platforms, it is required to start the clocks (mclk/sclk/fs)
before the stream start. Example: for few chrome systems, codec needs the
mclk/sclk to be enabled early for a successful clock synchronization and
for few IVI platforms, clock need to be enabled at boot and should be ON
always.
Add the required structures and create set_dma_control ipc to enable or
disable the clock. To enable sclk without fs, mclk ipc structure is used,
else sclkfs ipc structure is used.
Clock prepare/unprepare are used to enable/disable the clock as the IPC
will be sent in non-atomic context. The clk set_dma_control IPC
structures are populated during the set_rate callback and IPC is sent
to enable the clock during prepare callback.
This patch creates virtual clock driver, which allows the machine driver
to use the clock interface to send IPCs to DSP to enable/disable the
clocks.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
caused regressions for both twl4030 and twl6040 as it assumes the
ASoC driver is using regmap. As a side effect, this also causes a
considerable increase in idle power consumption omap3 boards using
twl4030 as the PMIC.
This is because the removal of read and write function pointers
causes some of the ASoC IO functions to not do anything. For example,
snd_soc_register_card() calls snd_soc_dapm_new_widgets() that calls
snd_soc_codec_drv_read() that now does nothing.
A long term solution suggested by Mark Brown <broonie@kernel.org>
is to make the twl drivers use regmap by adding a call to
snd_soc_codec_set_regmap(). This however needs more consideration
as currently the driver internal reads do caching and we would have
both regmap access and internal read/write access accessing the same
hardware registers.
So to fix the regression, let's just do a partial revert adding back
the read and write function pointers. Note that other non-regmap
ASoC drivers may need similar patches.
Fixes: 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
Fixes: 93a00c467f ("ASoC: don't use snd_soc_write/read on twl6040")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ADC support for the sun8i-codec driver.
This driver uses microphones widgets and routes provided by the
analog part (sun8i-codec-analog).
Some digital configurations are needed by creating new ADC widgets
and routes.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5514 dsp captures pcm data through spi directly, so we should not
use rockchip-i2s as it's cpu dai like other codecs.
Use dummy_dai for rt5514 dsp dailink to make voice wakeup work again.
Reported-by: Jimmy Cheng-Yi Chiang <cychiang@google.com>
Fixes: (72cfb0f20c ASoC: rockchip: Use codec of_node and dai_name for rt5514 dsp)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit fbb16563c6 ("ASoC: snd_soc_component_driver has pmdown_time")
added new .pmdown_time which is for inverted version of current
.ignore_pmdown_time
But it is confusable name. Let's rename it to .use_pmdown_time
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power Down Release Command (PMVR, PMDAC, RSTN, PMDA1-PMDA6)
which are located on PW_MGMT1 / PW_MGMT3 register must be
write again after at least 5 LRCK cycle or later on each command.
Otherwise, Playback volume will be 0dB.
Basically, it should be
1. PowerDownRelease by Power Management1 <= call 1.x after 5LRCK
1.x Dummy write to Power Management1
2. PowerDownRelease by Power Management3 <= call 2.x after 5LRCK
2.x Dummy write to Power Management3
To avoid too many dummy write, this patch is merging these.
1. PowerDownRelease by Power Management1
2. PowerDownRelease by Power Management3 <= call after 5LRCK
2.x Dummy write to Power Management1/3 <= merge dummy write
This patch adds dummy write when Playback Start timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit f523acebbb ("ASoC: add Component level pcm_new/pcm_free v2")
added component level pcm_new/pcm_free, but flush_delayed_work()
on soc_pcm_private_free() is called in for_each_rtdcom() loop.
It doesn't need to be called many times.
This patch moves it out of loop.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_rtdcom_lookup() look up component by uisng driver name.
Then, it uses component->driver->name.
Some driver might doesn't have it, thus it should care NULL pointer.
This patch solve this issue.
Reported-by: Mukunda,Vijendar <vijendar.mukunda@amd.com>
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Mukunda,Vijendar <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err already provides messages with prefix, so drop 'ASoC'
prefix.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_*() logging functions instead of plain printk and as
messages are now properly prefixed drop 'ASoC' prefix as well.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7fb59e940f ("ASoC: codecs: dmic: Make number of channels
configurable") introduces an optional property to the device tree
to specify the number of DMIC channels. dmic_codec_probe() uses
of_property_read_u32() to read the DT value, and expects a return
value of -ENOENT when the property does not exist. This expectation
is incorrect, the actual value returned in this case is -EINVAL (see
of_find_property_value_of_size(), which is called under the hood).
Check for -EINVAL instead.
Fixes: 7fb59e940f ("ASoC: codecs: dmic: Make number of channels configurable")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit dfa3cbb8(ASoC: mediatek: modify MT2701 AFE driver to adapt mfd device)
leads to the following static checker warning:
sound/soc/mediatek/mt2701/mt2701-afe-pcm.c:1535 mt2701_afe_pcm_dev_probe()
error: double free of 'component'
This patch fixes that and adds a helper mt2701_afe_add_component() to setup
component.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
