Before starting quering remote AMP controllers make sure
that there is local active AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some comparisons needs to double negation(!!) in order to make the value
of the field boolean. Add it to the macro makes the code more readable.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to authenticate and configure an incoming SCO connection, the
BT_DEFER_SETUP option was added. This option is intended to defer reply
to Connect Request on SCO sockets.
When a connection is requested, the listening socket is unblocked but
the effective connection setup happens only on first recv. Any send
between accept and recv fails with -ENOTCONN.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When the route changes (backup default route, VPNs) which affect a
masqueraded target, the packets were sent out with the outdated source
address. The patch addresses the issue by comparing the outgoing interface
directly with the masqueraded interface in the nat table.
Events are inefficient in this case, because it'd require adding route
events to the network core and then scanning the whole conntrack table
and re-checking the route for all entry.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We used to have several queueing backends, but nowadays only
nfnetlink_queue remains.
In light of this there doesn't seem to be a good reason to
support per-af registering -- just hook up nfnetlink_queue on module
load and remove it on unload.
This means that the userspace BIND/UNBIND_PF commands are now obsolete;
the kernel will ignore them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new operation to dump the content of the dying and
unconfirmed lists.
Under some situations, the global conntrack counter can be inconsistent
with the number of entries that we can dump from the conntrack table.
The way to resolve this is to allow dumping the content of the unconfirmed
and dying lists, so far it was not possible to look at its content.
This provides some extra instrumentation to resolve problematic situations
in which anyone suspects memory leaks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch modifies the conntrack subsystem so that all existing
allocated conntrack objects can be found in any of the following
places:
* the hash table, this is the typical place for alive conntrack objects.
* the unconfirmed list, this is the place for newly created conntrack objects
that are still traversing the stack.
* the dying list, this is where you can find conntrack objects that are dying
or that should die anytime soon (eg. once the destroy event is delivered to
the conntrackd daemon).
Thus, we make sure that we follow the track for all existing conntrack
objects. This patch, together with some extension of the ctnetlink interface
to dump the content of the dying and unconfirmed lists, will help in case
to debug suspected nf_conn object leaks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This creates amba_apb_device_add_res() and
amba_ahb_device_add_res() respectively, to add devices with
another parent than iomem_resource. This is needed to specify
that a device is contained in a specific IO range.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All users of __pata_platform_remove() have been converted to utilize the
common ata_platform_remove_one().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This relatively simple boiler-plate code is repeated in several platform
drivers. We should implement a common version in libata.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) should be used.
Quoting SATA spec 3.1:
If Hardware Feature Control is supported, then:
a) IDENTIFY DEVICE data word 78 bit 5 (see 13.2.1.18) shall be
set to one;
b) the SET FEATURES Select Hardware Feature Control subcommand
shall be supported (see 13.3.8);
c) page 08h of the Identify Device Data log (see 13.7.7) shall
be supported;
This patch is not tested on SATA HDD with DevSlp supported.
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 66fa7f215 "libata-acpi: improve ACPI disabling" introdcued the
behaviour of disabling ATA ACPI if ata_acpi_on_devcfg failed the 2nd
time, but commit 30dcf76ac dropped this behaviour and this caused
problem for Dimitris Damigos, where his laptop can not resume correctly.
The bugzilla page for it is:
https://bugzilla.kernel.org/show_bug.cgi?id=49331
The problem is, ata_dev_push_id will fail the 2nd time it is invoked,
and due to disabling ACPI code is dropped, ata_acpi_on_devcfg which
calls ata_dev_push_id will keep failing and eventually made the device
disabled.
This patch restores the original behaviour, if acpi failed the 2nd time,
disable acpi functionality for the device(and we do not event need to
add a debug message for this as it is still there ;-).
Reported-by: Dimitris Damigos <damigos@freemail.gr>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2irt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.8
Very quiet release for ASoC really:
- Standardisation of the logging.
- DT and dmaengine support for Atmel.
- Support for Wolfson ADSP cores.
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090.
Conflicts:
arch/x86/kernel/ptrace.c
Pull the latest RCU tree from Paul E. McKenney:
" The major features of this series are:
1. A first version of no-callbacks CPUs. This version prohibits
offlining CPU 0, but only when enabled via CONFIG_RCU_NOCB_CPU=y.
Relaxing this constraint is in progress, but not yet ready
for prime time. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/724, and are at branch rcu/nocb.
2. Changes to SRCU that allows statically initialized srcu_struct
structures. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/296, and are at branch rcu/srcu.
3. Restructuring of RCU's debugfs output. These commits were posted
to LKML at https://lkml.org/lkml/2012/10/30/341, and are at
branch rcu/tracing.
4. Additional CPU-hotplug/RCU improvements, posted to LKML at
https://lkml.org/lkml/2012/10/30/327, and are at branch rcu/hotplug.
Note that the commit eliminating __stop_machine() was judged to
be too-high of risk, so is deferred to 3.9.
5. Changes to RCU's idle interface, most notably a new module
parameter that redirects normal grace-period operations to
their expedited equivalents. These were posted to LKML at
https://lkml.org/lkml/2012/10/30/739, and are at branch rcu/idle.
6. Additional diagnostics for RCU's CPU stall warning facility,
posted to LKML at https://lkml.org/lkml/2012/10/30/315, and
are at branch rcu/stall. The most notable change reduces the
default RCU CPU stall-warning time from 60 seconds to 21 seconds,
so that it once again happens sooner than the softlockup timeout.
7. Documentation updates, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/280, and are at branch rcu/doc.
A couple of late-breaking changes were posted at
https://lkml.org/lkml/2012/11/16/634 and
https://lkml.org/lkml/2012/11/16/547.
8. Miscellaneous fixes, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/309, along with a late-breaking
change posted at Fri, 16 Nov 2012 11:26:25 -0800 with message-ID
<20121116192625.GA447@linux.vnet.ibm.com>, but which lkml.org
seems to have missed. These are at branch rcu/fixes.
9. Finally, a fix for an lockdep-RCU splat was posted to LKML
at https://lkml.org/lkml/2012/11/7/486. This is at rcu/next. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Define SYMBOL_PREFIX to be the same as CONFIG_SYMBOL_PREFIX if set by
the architecture, or "" otherwise. This avoids the need for ugly #ifdefs
whenever symbols are referenced in asm blocks.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Joe Perches <joe@perches.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
# make C=2 CF=-D__CHECK_ENDIAN__ net/ipv4/inet_hashtables.o
...
net/ipv4/inet_hashtables.c:242:7: warning: restricted __portpair degrades to integer
net/ipv4/inet_hashtables.c:242:7: warning: restricted __addrpair degrades to integer
...
Move __portpair/__addrpair from include/net/inet_hashtables.h
to include/net/sock.h where we need them in struct sock_common
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ling Ma <ling.ma.program@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse says:
====================
This is the result of pulling on the thread started by Krzysztof Mazur's
original patch 'pppoatm: don't send frames to destroyed vcc'.
Various problems in the pppoatm and br2684 code are solved, some of which
were easily triggered and would panic the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The immediate use case for this is that it will allow us to ensure that a
pppoatm queue is woken after it has to drop a packet due to the sock being
locked.
Note that 'release_cb' is called when the socket is *unlocked*. This is
not to be confused with vcc_release() — which probably ought to be called
vcc_close().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
Pull perf fixes from Ingo Molnar:
"This is mostly about unbreaking architectures that took the UAPI
changes in the v3.7 cycle, plus misc fixes."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix building perf kvm on non x86 arches
perf kvm: Rename perf_kvm to perf_kvm_stat
perf: Make perf build for x86 with UAPI disintegration applied
perf powerpc: Use uapi/unistd.h to fix build error
tools: Pass the target in descend
tools: Honour the O= flag when tool build called from a higher Makefile
tools: Define a Makefile function to do subdir processing
x86: Export asm/{svm.h,vmx.h,perf_regs.h}
perf tools: Fix strbuf_addf() when the buffer needs to grow
perf header: Fix numa topology printing
perf, powerpc: Fix hw breakpoints returning -ENOSPC
As of 026359b [ipv6: Send ICMPv6 RSes only when RAs are accepted], the
logic determining whether to send Router Solicitations is identical
to the logic determining whether kernel accepts Router Advertisements.
However the condition itself is repeated in several code locations.
Unify it by introducing 'ipv6_accept_ra()' accessor.
Also, simplify the condition expression, making it more readable.
No semantic change.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[jejb: split this core change into a separate patch]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Reviewed-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQrSVZAAoJEBvUPslcq6Vz6jwQAILCHwQK9P5Up2Fejxrz51SE
GSuWjmo0+b1jfPphg9m7ctJCb5wCuVYgOf7d2XkZgHqjzop4fGX/bHYoviZRxBGl
atqGH8velt9Jhr/FUo6KczgntGT339BXkdoN+WwP6VbM72mzReV0UOVq9II8BItK
HyQNqJlcAZiPoIcpHnM6rYxJFXnBrlQKkJYlG9EaGNdEipeKsY+f8qOSq00gKgDp
epfNaiCkinYwPXTRX3/NvFH3vwrKjvpDg7qTpUi/V1AebngH5GZrzfVLr3mWIRy6
vmMe/qu5tz55+opvuIN8AFDZA+DLie1YAOwgbNAQ6yHft3WwFT/8rB7+LnxFhFb0
cNc++NxsD9dJS5Hed1q02kDZ4mkN8Ss41mTzyK0g1sIQzdumDUMDo8SGprxRBfls
RLVYWLEoGZ9gPmXwlUHD9+hEz6SrwDN0sUJRQH7omcyFT7oOfwocJaO+FzAZ9QE2
uPYF/h/k15rRlFt4wdGuhaYRXhayBrAnjr43FxfZiIbqdDWaz77j1cSbmkvaEAYE
BQH8xWXmDjBIZIm0kxt3ajB7M+z+ZH/4D2pmHU7Ljd6ybewxrI+SasQ5ZJT+EJSH
ZBSGVMsrgD/oesNr0GrA/l3Z+FTnRpWwEcXxydWZBcENRVALfBm+khE5jqSo+hag
KAPEfoHBDyxQ91OFO8rb
=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Make it possible to disconnect the IB RC connection used by the SRP
protocol to communicate with a target.
Have the SRP transport layer create a sysfs "delete" attribute for
initiator drivers that support this functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'arm-privcmd-for-3.8' of git://xenbits.xen.org/people/ianc/linux:
xen: arm: implement remap interfaces needed for privcmd mappings.
xen: correctly use xen_pfn_t in remap_domain_mfn_range.
xen: arm: enable balloon driver
xen: balloon: allow PVMMU interfaces to be compiled out
xen: privcmd: support autotranslated physmap guests.
xen: add pages parameter to xen_remap_domain_mfn_range
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With the recent work to remove CONFIG_HOTPLUG, we are starting to get a
bunch of __devinit section warnings, despite CONFIG_HOTPLUG always being
enabled. So, stop marking the sections entirely, by defining them away
the section markings in init.h
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68835aba4d (net: optimize INET input path further)
moved some fields used for tcp/udp sockets lookup in the first cache
line of struct sock_common.
This patch moves inet_dport/inet_num as well, filling a 32bit hole
on 64 bit arches and reducing number of cache line misses in lookups.
Also change INET_MATCH()/INET_TW_MATCH() to perform the ports match
before addresses match, as this check is more discriminant.
Remove the hash check from MATCH() macros because we dont need to
re validate the hash value after taking a refcount on socket, and
use likely/unlikely compiler hints, as the sk_hash/hash check
makes the following conditional tests 100% predicted by cpu.
Introduce skc_addrpair/skc_portpair pair values to better
document the alignment requirements of the port/addr pairs
used in the various MATCH() macros, and remove some casts.
The namespace check can also be done at last.
This slightly improves TCP/UDP lookup times.
IP/TCP early demux needs inet->rx_dst_ifindex and
TCP needs inet->min_ttl, lets group them together in same cache line.
With help from Ben Hutchings & Joe Perches.
Idea of this patch came after Ling Ma proposal to move skc_hash
to the beginning of struct sock_common, and should allow him
to submit a final version of his patch. My tests show an improvement
doing so.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Joe Perches <joe@perches.com>
Cc: Ling Ma <ling.ma.program@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new subsystem that probes on kernel boundaries
to keep track of the transitions between level contexts
with two basic initial contexts: user or kernel.
This is an abstraction of some RCU code that use such tracking
to implement its userspace extended quiescent state.
We need to pull this up from RCU into this new level of indirection
because this tracking is also going to be used to implement an "on
demand" generic virtual cputime accounting. A necessary step to
shutdown the tick while still accounting the cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[ paulmck: fix whitespace error and email address. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Merge misc fixes from Andrew Morton:
"Seven fixes, some of them fingers-crossed :("
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (7 patches)
drivers/rtc/rtc-tps65910.c: fix invalid pointer access on _remove()
mm: soft offline: split thp at the beginning of soft_offline_page()
mm: avoid waking kswapd for THP allocations when compaction is deferred or contended
revert "Revert "mm: remove __GFP_NO_KSWAPD""
mm: vmscan: fix endless loop in kswapd balancing
mm/vmemmap: fix wrong use of virt_to_page
mm: compaction: fix return value of capture_free_page()
If CONFIG_SSB_EMBEDDED or CONFIG_SSB_DRIVER_MIPS is set and
CONFIG_SSB_DRIVER_EXTIF is not set, it will cause compile problems
because of missing functions. This patch fixes these problems.
The mips driver now also uses ssb_chipco_available() instead of
checking bus->chipco.dev manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From Kukjin Kim:
Just adding camif gpio setup and clkdev.
* 'next/cam-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
+ Linux 3.7-rc6
Conflicts due to the 3.7-rc6 sync: arch/arm/mach-highbank/system.c
include/linux/clk-provider.h, resolved as in other branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes an unused parameter (src_net) from rtnl_create_link()
method and from the method single invocation, in veth.
This parameter was used in the past when calling
ops->get_tx_queues(src_net, tb) in rtnl_create_link().
The get_tx_queues() member of rtnl_link_ops was replaced by two methods,
get_num_tx_queues() and get_num_rx_queues(), which do not get any
parameter. This was done in commit d40156aa5e by
Jiri Pirko ("rtnl: allow to specify different num for rx and tx queue count").
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
merge conflicts with orion/*
- arch/arm/mach-kirkwood/Kconfig
- select everything
- arch/arm/mach-kirkwood/board-dt.c
- remove AUXDATA
- keep all of_machine_is_compatible()
- use of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsFAhAAoJEAi3KVZQDZAedzgH/3VodO3dDqL4A5HCoUj56HXF
Chkv1cl+1VS3sPnsbbluG0fmDdB619i4Oi2bUWc1YdLpEE0xgyjeAzl5vZDFBjrS
tb8nhWCd2vEcKFSC+HVU2Rhj0NwgUoQifoeD7NSovYZJE6+z+KEY5ny0sE4uaWE1
NL+StBI9dH+SvMi59rnsAxteAnBEAosUoY4KaoHcTHvPsqm9xW5GBh1MkSXQB7fx
kwRrdCaM8U3y3J933/Y4C3maDDQVL7v27YgQp+U5r/eRyN7fVVccxLr6xwl9sck2
fjEpbNRYMImvCOKh8+dhllf/8ZOmjdOore4ORbk4Ulame2KL6pG/2fZ+5N+FrRQ=
=QHBZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper. Unfortunately this is a combined branch with all
mvebu code as one drop, something we normally try to avoid and instead
slice vendor topics across our branches. Hopefully we can avoid doing
this again for 3.9!
mvebu everything for v3.8
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
* tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux: (85 commits)
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
arm: mvebu: Add support for coherency fabric in mach-mvebu
arm: mvebu: update defconfig to include XOR driver
arm: mvebu: update defconfig to include network driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
net/ipv6/exthdrs_core.c
Jesse Gross says:
====================
This series of improvements for 3.8/net-next contains four components:
* Support for modifying IPv6 headers
* Support for matching and setting skb->mark for better integration with
things like iptables
* Ability to recognize the EtherType for RARP packets
* Two small performance enhancements
The movement of ipv6_find_hdr() into exthdrs_core.c causes two small merge
conflicts. I left it as is but can do the merge if you want. The conflicts
are:
* ipv6_find_hdr() and ipv6_find_tlv() were both moved to the bottom of
exthdrs_core.c. Both should stay.
* A new use of ipv6_find_hdr() was added to net/netfilter/ipvs/ip_vs_core.c
after this patch. The IPVS user has two instances of the old constant
name IP6T_FH_F_FRAG which has been renamed to IP6_FH_F_FRAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It apepars that this patch was innocent, and we hope that "mm: avoid
waking kswapd for THP allocations when compaction is deferred or
contended" will fix the final kswapd-spinning cause.
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.
Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
Replace references to and remove the connector property fxns, which
have been superseded with the more general object property fxns:
+ drm_connector_attach_property -> drm_object_attach_property
+ drm_connector_property_set_value -> drm_object_property_set_value
+ drm_connector_property_get_value -> drm_object_property_get_value
Signed-off-by: Rob Clark <rob@ti.com>
Add PCI support for s390, (only 64 bit mode is supported by hardware):
- PCI facility tests
- PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit
- map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions
- pci_iomap implementation
- memcpy_fromio/toio
- pci_root_ops using special pcilg/pcistg
- device, bus and domain allocation
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for translating ACPI GPIO pin numbers to Linux GPIO API pins.
Needs a gpio controller driver with the acpi handler hook set.
Drivers can use acpi_get_gpio() to translate ACPI5 GpioIO and GpioInt
resources to Linux GPIO's.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The 'io_mutex' is not used anywhere.
The regmap API supports the mutex internally, so no additional mutex
is required.
And 'domain' private data is unnecessary because the irq domain is
already registered by using regmap_add_irq_chip().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the very first patch, stmpe core driver is using irq_invert_polarity as
part of platform data. But, nobody is actually using it in kernel till now.
Also, this is not something part of hardware specs, but is included to cater
some board mistakes or quirks.
So, better get rid of it. This is earlier discussed here:
https://lkml.org/lkml/2012/11/27/636
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ERROR: "allnodes" [drivers/w1/masters/w1-gpio.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[grant.likely: allnodes is too generic; rename to of_allnodes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ville Syrjala <syrjala@sci.fi>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/devel-prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
* tag 'omap-for-v3.8/devel-prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (49 commits)
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP44xx: clock: drop obsolete clock data
ARM: OMAP4: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: hwmod: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: clock: Switch to COMMON clk
ARM: OMAP2: clock: Add 24xx data using common struct clk
ARM: OMAP3: clock: Add 3xxx data using common struct clk
ARM: AM33XX: clock: add clock data in common clock format
ARM: OMAP4: clock: Add 44xx data using common struct clk
ARM: OMAP2+: clock: add OMAP CCF convenience macros to mach-omap2/clock.h
...
Some context conflicts due to nearby changes resolved in
arch/arm/mach-omap2/io.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
By Lee Jones (42) and others
via Olof Johansson (13) and others
* next/dt: (249 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
We really don't want to look at the block size for the raw block device
accesses in fs/block-dev.c, because it may be changing from under us.
So get rid of the max_block logic entirely, since the caller should
already have done it anyway.
That leaves the only user of this function in fs/buffer.c, so move the
whole function there and make it static.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-cpuidle:
cpuidle: Measure idle state durations with monotonic clock
cpuidle: fix a suspicious RCU usage in menu governor
cpuidle: support multiple drivers
cpuidle: prepare the cpuidle core to handle multiple drivers
cpuidle: move driver checking within the lock section
cpuidle: move driver's refcount to cpuidle
cpuidle: fixup device.h header in cpuidle.h
cpuidle / sysfs: move structure declaration into the sysfs.c file
cpuidle: Get typical recent sleep interval
cpuidle: Set residency to 0 if target Cstate not enter
cpuidle: Quickly notice prediction failure in general case
cpuidle: Quickly notice prediction failure for repeat mode
cpuidle / sysfs: move kobj initialization in the syfs file
cpuidle / sysfs: change function parameter
* pm-cpufreq: (21 commits)
cpufreq: ondemand: update sampling rate only on right CPUs
cpufreq: SPEAr: Add CPUFreq driver
cpufreq: governors: Fix jiffies/cputime mixup (revisited)
cpufreq: ondemand: fix wrong delay sampling rate
cpufreq: exynos: Use static for functions used in only this file
cpufreq: exynos: Broadcast frequency change notifications for all cores
cpufreq: remove use of __devexit
cpufreq: remove use of __devinit
cpufreq: remove use of __devexit_p
cpufreq: Remove unnecessary initialization of a local variable
cpufreq: Make sure target freq is within limits
cpufreq: Avoid calling cpufreq driver's target() routine if target_freq == policy->cur
cpufreq: Fix sparse warning by making local function static
cpufreq: Fix sparse warnings by updating cputime64_t to u64
cpufreq: governors: remove redundant code
cpufreq: return early from __cpufreq_driver_getavg()
cpufreq: fix jiffies/cputime mixup in conservative/ondemand governors
cpufreq: Improve debug prints
cpufreq: Move common part from governors to separate file, v2
cpufreq / core: Fix printing of governor and driver name
...
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
* acpica: (26 commits)
ACPICA: Update version to 20121018
ACPICA: AcpiGetObjectInfo: Add support for ACPI 5 _SUB method
ACPICA: Update for 64-bit generation of recent error message changes
ACPICA: Fix externalize name to complete migration to ACPI_MOVE_NAME
ACPICA: Add starting offset parameter to common dump buffer routine
ACPICA: Deploy ACPI_MOVE_NAME across ACPICA source base
ACPICA: Update support for ACPI 5 MPST table
ACPICA: Enhance error reporting for invalid opcodes and bad ACPI_NAMEs
ACPICA: Add ACPI_MOVE_NAME macro to optimize 4-byte ACPI_NAME copies
ACPICA: AcpiExec: Improve algorithm for tracking memory leaks
ACPICA: Add debug print message for mutex objects that are force-released
ACPICA: Resource Mgr: Small fix for buffer size calculation
ACPICA: Remove extra spaces after periods in the Intel license
ACPICA: Remove extra spaces after periods within comments
ACPICA: Update local C library module comments for ASCII table
ACPICA: Fix for predefined name loop during ACPICA initialization
ACPICA: Fix some typos in comments
ACPICA: ACPICA core: Cleanup empty lines at file start and end
ACPICA: Audit/update for ACPICA return macros and debug depth counter
ACPICA: Fix unmerged acmacros.h divergences.
...
* acpi-dev-pm:
ACPI / PM: Allow attach/detach routines to change device power states
ACPI / PM: Introduce os_accessible flag for power_state
ACPI / PM: Add check preventing transitioning to non-D0 state from D3.
ACPI / PM: Fix build problem when CONFIG_ACPI or CONFIG_PM is not set
ACPI / PM: Fix build problem related to acpi_target_system_state()
ACPI / PM: Provide ACPI PM callback routines for subsystems
ACPI / PM: Move device PM functions related to sleep states
ACPI / PM: Provide device PM functions operating on struct acpi_device
ACPI / PM: Split device wakeup management routines
ACPI / PM: Move runtime remote wakeup setup routine to device_pm.c
ACPI / PM: Move device power state selection routine to device_pm.c
ACPI / PM: Move routines for adding/removing device wakeup notifiers
ACPI / PM: Fix device PM kernedoc comments and #ifdefs
* pm-qos:
PM / QoS: Handle device PM QoS flags while removing constraints
PM / QoS: Resume device before exposing/hiding PM QoS flags
PM / QoS: Document request manipulation requirement for flags
PM / QoS: Fix a free error in the dev_pm_qos_constraints_destroy()
PM / QoS: Fix the return value of dev_pm_qos_update_request()
PM / ACPI: Take device PM QoS flags into account
PM / Domains: Check device PM QoS flags in pm_genpd_poweroff()
PM / QoS: Make it possible to expose PM QoS device flags to user space
PM / QoS: Introduce PM QoS device flags support
PM / QoS: Prepare struct dev_pm_qos_request for more request types
PM / QoS: Introduce request and constraint data types for PM QoS flags
PM / QoS: Prepare device structure for adding more constraint types
This reverts the block-device direct access code to the previous
unlocked code, now that fs/buffer.c no longer needs external locking.
With this, fs/block_dev.c is back to the original version, apart from a
whitespace cleanup that I didn't want to revert.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes three methods to be static and removes their
EXPORT_SYMBOLs in core/dev.c and their external declaration in
netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and
napi_skb_finish(), which are in the GRO rx path, are not used
outside core/dev.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing function does not change the passed device_node pointer. It is
only handed to of_get_property which itself takes a const struct device_node.
of_parse_phandle() can therefore take a const pointer as well.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[grant.likely: drop extraneous whitespace change]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We use XENMEM_add_to_physmap_range which is the preferred interface
for foreign mappings.
Acked-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
For Xen on ARM a PFN is 64 bits so we need to use the appropriate
type here.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: include the necessary header,
Reported-by: Fengguang Wu <fengguang.wu@intel.com> ]
Also introduce xen_unmap_domain_mfn_range. These are the parts of
Mukesh's "xen/pvh: Implement MMU changes for PVH" which are also
needed as a baseline for ARM privcmd support.
The original patch was:
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This derivative is also:
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
This patch adds DMA_ATTR_FORCE_CONTIGUOUS attribute to the DMA-mapping
subsystem.
By default DMA-mapping subsystem is allowed to assemble the buffer
allocated by dma_alloc_attrs() function from individual pages if it can
be mapped as contiguous chunk into device dma address space. By
specifing this attribute the allocated buffer is forced to be contiguous
also in physical memory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This function returns the VIC of the mode. This value can be used when
creating AVI InfoFrames.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50371
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Samsung Framebuffer changes for the 3.8 merge window.
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
* 'samsung-fb-next' of git://github.com/jingoo/linux:
video: s3c-fb: fix red offset and length for ARGB232 format
video: s3c-fb: return an error when bpp is invalid
video: s3c-fb: add "drop through" comment
video: s3c-fb: use dev_get_drvdata() instead of platform_get_drvdata()
video: s3c-fb: use FIMD_V8_VIDTCON0 for EXYNOS5 FIMD
video: s3c-fb: fix help message for FB_S3C_DEBUG_REGWRITE
video: s3c-fb: fix typo in comment
video: s3c-fb: add the bit definitions for VIDCON0_VIDOUT_WB
video: s3c-fb: move the bit definitions for DITHMODE register
video: s3c-fb: move the bit definitions for WINxMAP and WPALCON register
video: s3c-fb: move the bit definitions for VIDINTCON0 register
video: s3c-fb: move the address definition for VIDOSD register
video: s3c-fb: move the address definitions for VIDTCON registers
video: s3c-fb: clean the bit definition for WINCON register
the first one is equal to signal_pt_regs(), the second is never used
(and always NULL, while we are at it).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Always equal to task_pt_regs(current); defined only when we are in
signal delivery. It may be different from current_pt_regs() - e.g.
architectures like m68k may have pt_regs location on exception
different from that on a syscall and signals (just as ptrace handling)
may happen on exceptions as well as on syscalls.
When they are equal, it's often better to have signal_pt_regs
defined (in asm/ptrace.h) as current_pt_regs - that tends to be
optimized better than default would be. However, optimisation is
the only reason why we might want an arch-specific definition;
if current_pt_regs() and task_pt_regs(current) have different
values, the latter one is right.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and get rid of idiotic struct pt_regs * in asm-generic/syscalls.h
prototypes of the same, while we are at it. Eventually we want those
in linux/syscalls.h, of course, but that'll have to wait a bit.
Note that there are *three* variants of sys_clone() order of arguments.
Braindamage galore...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As on ia64 builds we get:
include/xen/interface/version.h: In function 'xen_running_on_version_or_later':
include/xen/interface/version.h:76: error: implicit declaration of function 'HYPERVISOR_xen_version'
We can later on make this function exportable if there are
modules using part of it. For right now the only two users are
built-in.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As the I2S src clks are registered with clkdev using generic
connection id, driver can get the clk name using generic id.
So the variable representing the array of rclk src clks is
deleted.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
task_cputime_adjusted() and thread_group_cputime_adjusted()
essentially share the same code. They just don't use the same
source:
* The first function uses the cputime in the task struct and the
previous adjusted snapshot that ensures monotonicity.
* The second adds the cputime of all tasks in the group and the
previous adjusted snapshot of the whole group from the signal
structure.
Just consolidate the common code that does the adjustment. These
functions just need to fetch the values from the appropriate
source.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
We have thread_group_cputime() and thread_group_times(). The naming
doesn't provide enough information about the difference between
these two APIs.
To lower the confusion, rename thread_group_times() to
thread_group_cputime_adjusted(). This name better suggests that
it's a version of thread_group_cputime() that does some stabilization
on the raw cputime values. ie here: scale on top of CFS runtime
stats and bound lower value for monotonicity.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Use synchronize_sched_expedited() instead of synchronize_sched()
to improve mount speed.
This patch improves mount time from 0.500s to 0.013s for Jeff's
test-case.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.
Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some other device functions need to integrate with signal sources in the
audio portion (primarily for haptics) so allow CODEC to export the DAPM
context by pointing to it from the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds V4L2 driver for Samsung S3C24XX/S3C64XX SoC series
camera interface. The driver exposes a subdev device node for CAMIF
pixel resolution and crop control and two video capture nodes - for
the "codec" and "preview" data paths. It has been tested on Mini2440
(s3c2440) and Mini6410 (s3c6410) board with gstreamer and mplayer.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Andrey Gusakov <dron0gus@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On csrow-based memory controllers, we combine the csrow size from both
channels and there's no need to do that again in csrow_size_show which
leads to double the size of a csrow.
Fix it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
I didn't bother with documenting the really trivial new "extract
something from dpcd" helpers, but the i2c over aux ch is now
documented a bit.
v2: Clarify the comment for i2c_dp_aux_add_bus a bit.
v3: Fix more spelling fail spotted by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
While hashtab should now be RCU-safe, Add a drm_ht_xxx_api for consumers
to use to make it obvious what locking mechanism is used.
Document the way the rcu-safe interface should be used.
Don't use rcu-safe list traversal in modify operations where we should use
a spinlock / mutex anyway.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already expect TFO->get_blocks() to return sector_t for zero value case
when doing WRITE_SAME to the end of the backend device, so go ahead and return
sector_t from spc_get_write_same_sectors() to handle this case properly.
Also, update the single iblock_execute_write_same() caller of this code.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
KVM added a global variable to guarantee monotonicity in the guest.
One of the reasons for that is that the time between
1. ktime_get_ts(×pec);
2. rdtscll(tsc);
Is variable. That is, given a host with stable TSC, suppose that
two VCPUs read the same time via ktime_get_ts() above.
The time required to execute 2. is not the same on those two instances
executing in different VCPUS (cache misses, interrupts...).
If the TSC value that is used by the host to interpolate when
calculating the monotonic time is the same value used to calculate
the tsc_timestamp value stored in the pvclock data structure, and
a single <system_timestamp, tsc_timestamp> tuple is visible to all
vcpus simultaneously, this problem disappears. See comment on top
of pvclock_update_vm_gtod_copy for details.
Monotonicity is then guaranteed by synchronicity of the host TSCs
and guest TSCs.
Set TSC stable pvclock flag in that case, allowing the guest to read
clock from userspace.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
As suggested by John, export time data similarly to how its
done by vsyscall support. This allows KVM to retrieve necessary
information to implement vsyscall support in KVM guests.
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The atm is using atmvcc->push(vcc, NULL) callback to notify protocol
that vcc will be closed and protocol must detach from it. This callback
is usually used by protocol to decrement module usage count by module_put(),
but it leaves small window then module is still used after module_put().
Now the owner of push() callback is kept in atmvcc and
module_put(atmvcc->owner) is called after the protocol is detached from vcc.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Pull media fixes from Mauro Carvalho Chehab:
"For some media fixes:
- dvb_usb_v2: some fixes at the core
- Some fixes on some embedded drivers: soc_camera, adv7604, omap3isp,
exynos/s5p
- Several Exynos4/5 camera fixes
- a fix at stv0900 driver
- a few USB ID additions to detect more variants of rtl28xxu-based
sticks"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
[media] rtl28xxu: 0ccd:00d7 TerraTec Cinergy T Stick+
[media] rtl28xxu: 1d19:1102 Dexatek DK mini DVB-T Dongle
[media] mt9v022: fix the V4L2_CID_EXPOSURE control
[media] mx2_camera: fix missing unlock on error in mx2_start_streaming()
[media] media: omap1_camera: fix const cropping related warnings
[media] media: mx1_camera: use the default .set_crop() implementation
[media] media: mx2_camera: fix const cropping related warnings
[media] media: mx3_camera: fix const cropping related warnings
[media] media: pxa_camera: fix const cropping related warnings
[media] media: sh_mobile_ceu_camera: fix const cropping related warnings
[media] media: sh_vou: fix const cropping related warnings
[media] adv7604: restart STDI once if format is not found
[media] adv7604: use presets where possible
[media] adv7604: Replace prim_mode by mode
[media] adv7604: cleanup references
[media] dvb_usb_v2: switch interruptible mutex to normal
[media] dvb_usb_v2: fix pid_filter callback error logging
[media] exynos-gsc: change driver compatible string
[media] omap3isp: Fix warning caused by bad subdev events operations prototypes
[media] omap3isp: video: Fix warning caused by bad vidioc_s_crop prototype
...
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is based on Linux 3.7 rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/KTt
-----END PGP SIGNATURE-----
Merge tag 'pull_req_20121122' of git://git.kernel.org/pub/scm/linux/kernel/git/mzx/extcon into char-misc-next
MyungJoo writes:
"extcon pull request targetting Linux 3.8 for Greg KH on 2012.11.22
This is based on Linux 3.7 rc6"
If a driver supports P2P GO powersave, allow it to
set the new feature flags for it and allow userspace
to configure the parameters for it. This can be done
at GO startup and later changed with SET_BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Determine the VHT channel from the AP's VHT operation IE
(if present) and configure the hardware to that channel
if it is supported. If channel contexts cause a channel
to not be usable, try a smaller bandwidth.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 'fbdev-next' of github.com:timur-tabi/linux-2.6:
drivers/video: fsl-diu-fb: store EDID data in the global object
drivers/video: fsl-diu-fb: don't touch registers for unused features
drivers/video: fsl-diu-fb: clean up reset of primary display
drivers/video: fsl-diu-fb: remove unused 'cursor_reset' variable
drivers/video: fsl-diu-fb: improve message displays
drivers/video: fsl-diu-fb: streamline enabling of interrupts
drivers/video: fsl-diu-fb: add support for set_gamma ioctls
drivers/video: fsl-diu-fb: simplify platforms that have only one port
MAINTAINERS: Make Timur Tabi the maintainer for the Freescale DIU driver
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge SH Mobile LCDC patches from Laurent.
* 'lcdc-next' of git://linuxtv.org/pinchartl/fbdev:
fbdev: sh_mobile_lcdc: Make sh_mobile_lcdc_sys_bus_ops static
sh: kfr2r09: Use the backlight API for brightness control
ARM: mach-shmobile: ag5evm: Use the backlight API for brightness control
fbdev: sh_mobile_lcdc: Remove unused get_brightness pdata callback
sh: ecovec24: Remove unused get_brightness LCDC callback
sh: ap325rxa: Remove unused get_brightness LCDC callback
ARM: mach-shmobile: mackerel: Removed unused get_brightness callback
fbdev: sh_mobile_lcdc: Store the backlight brightness internally
fbdev: sh_mipi_dsi: Remove the unused sh_mipi_dsi_info lcd_chan field
ARM: mach-shmobile: Remove the unused sh_mipi_dsi_info lcd_chan field
fbdev: sh_mipi_dsi: Remove last reference to LCDC platform data
fbdev: sh_mipi_dsi: Use the LCDC entity default mode
fbdev: sh_mipi_dsi: Use the sh_mipi_dsi_info channel field
ARM: mach-shmobile: Initiliaze the new sh_mipi_dsi_info channel field
fbdev: sh_mipi_dsi: Add channel field to platform data
ARM: mach-shmobile: ag5evm: Add LCDC tx_dev field to platform data
fbdev: sh_mobile_lcdc: Remove priv argument from channel and overlay init
fbdev: sh_mobile_lcdc: Rename mode argument to modes
fbdev: sh_mobile_lcdc: Get display dimensions from the channel structure
fbdev: sh_mobile_lcdc: use dma_mmap_coherent
Some of the chandef checking that we do in cfg80211
to check if a channel is supported or not is also
needed in mac80211, so rework that a bit and export
the functions that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Force large capacity (> 0xFFFFFFFF blocks) drives to use READ/WRITE(16) instead
of READ/WRITE(10). Some(most/all?) USB enclosures do not like READ(10) commands
when a large capacity drive is installed. This issue was reported and discussed
here: http://marc.info/?l=linux-usb&m=135247705222324
Signed-off-by: Jason J. Herne <hernejj@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With "mm: vmscan: scale number of pages reclaimed by reclaim/compaction
based on failures" reverted, Zdenek Kabelac reported the following
Hmm, so it's just took longer to hit the problem and observe
kswapd0 spinning on my CPU again - it's not as endless like before -
but still it easily eats minutes - it helps to turn off Firefox
or TB (memory hungry apps) so kswapd0 stops soon - and restart
those apps again. (And I still have like >1GB of cached memory)
kswapd0 R running task 0 30 2 0x00000000
Call Trace:
preempt_schedule+0x42/0x60
_raw_spin_unlock+0x55/0x60
put_super+0x31/0x40
drop_super+0x22/0x30
prune_super+0x149/0x1b0
shrink_slab+0xba/0x510
The sysrq+m indicates the system has no swap so it'll never reclaim
anonymous pages as part of reclaim/compaction. That is one part of the
problem but not the root cause as file-backed pages could also be
reclaimed.
The likely underlying problem is that kswapd is woken up or kept awake
for each THP allocation request in the page allocator slow path.
If compaction fails for the requesting process then compaction will be
deferred for a time and direct reclaim is avoided. However, if there
are a storm of THP requests that are simply rejected, it will still be
the the case that kswapd is awake for a prolonged period of time as
pgdat->kswapd_max_order is updated each time. This is noticed by the
main kswapd() loop and it will not call kswapd_try_to_sleep(). Instead
it will loopp, shrinking a small number of pages and calling
shrink_slab() on each iteration.
The temptation is to supply a patch that checks if kswapd was woken for
THP and if so ignore pgdat->kswapd_max_order but it'll be a hack and not
backed up by proper testing. As 3.7 is very close to release and this
is not a bug we should release with, a safer path is to revert "mm:
remove __GFP_NO_KSWAPD" for now and revisit it with the view to ironing
out the balance_pgdat() logic in general.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit baf05aa927 ("bug: introduce BUILD_BUG_ON_INVALID() macro")
introduces this macro only when _CHECKER_ is not defined. Define a
silent macro in the else condition to fix following sparse warning:
mm/filemap.c:395:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
mm/filemap.c:396:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
mm/filemap.c:397:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
include/linux/mm.h:419:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
include/linux/mm.h:419:9: error: not a function <noident>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 92e3229dcd
("xen/acpi: ACPI PAD driver") adds a new function but forgets to
use the right header. Without it, we get:
In file included from drivers/xen/features.c:15:0:
include/xen/interface/version.h: In function ‘xen_running_on_version_or_later’:
include/xen/interface/version.h:72:2: error: implicit declaration of function ‘xen_domain’ [-Werror=implicit-function-declaration]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[Issue]
Currently, a variable name, which identifies each entry, consists of type, id and ctime.
But if multiple events happens in a short time, a second/third event may fail to log because
efi_pstore can't distinguish each event with current variable name.
[Solution]
A reasonable way to identify all events precisely is introducing a sequence counter to
the variable name.
The sequence counter has already supported in a pstore layer with "oopscount".
So, this patch adds it to a variable name.
Also, it is passed to read/erase callbacks of platform drivers in accordance with
the modification of the variable name.
<before applying this patch>
a variable name of first event: dump-type0-1-12345678
a variable name of second event: dump-type0-1-12345678
type:0
id:1
ctime:12345678
If multiple events happen in a short time, efi_pstore can't distinguish them because
variable names are same among them.
<after applying this patch>
it can be distinguishable by adding a sequence counter as follows.
a variable name of first event: dump-type0-1-1-12345678
a variable name of Second event: dump-type0-1-2-12345678
type:0
id:1
sequence counter: 1(first event), 2(second event)
ctime:12345678
In case of a write callback executed in pstore_console_write(), "0" is added to
an argument of the write callback because it just logs all kernel messages and
doesn't need to care about multiple events.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[Issue]
Currently, a variable name, which is used to identify each log entry, consists of type,
id and ctime. But an erase callback does not use ctime.
If efi_pstore supported just one log, type and id were enough.
However, in case of supporting multiple logs, it doesn't work because
it can't distinguish each entry without ctime at erasing time.
<Example>
As you can see below, efi_pstore can't differentiate first event from second one without ctime.
a variable name of first event: dump-type0-1-12345678
a variable name of second event: dump-type0-1-23456789
type:0
id:1
ctime:12345678, 23456789
[Solution]
This patch adds ctime to an argument of an erase callback.
It works across reboots because ctime of pstore means the date that the record was originally stored.
To do this, efi_pstore saves the ctime to variable name at writing time and passes it to pstore
at reading time.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[Issue]
As discussed in a thread below, Running out of space in EFI isn't a well-tested scenario.
And we wouldn't expect all firmware to handle it gracefully.
http://marc.info/?l=linux-kernel&m=134305325801789&w=2
On the other hand, current efi_pstore doesn't check a remaining space of storage at writing time.
Therefore, efi_pstore may not work if it tries to write a large amount of data.
[Patch Description]
To avoid handling the situation above, this patch checks if there is a space enough to log with
QueryVariableInfo() before writing data.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes build warnings when CONFIG_LEDS_TRIGGERS is
disabled as below:
include/linux/leds.h:158:18: warning: 'struct led_trigger' declared inside parameter list [enabled by default]
include/linux/leds.h:158:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled
by default]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Implements a "led_trigger_rename" function to rename a trigger with
proper locking.
This assumes that led name was originally allocated in non-constant
storage.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Instead of having the getsockopt() of SO_BINDTODEVICE return an index, which
will then require another call like if_indextoname() to get the actual interface
name, have it return the name directly.
This also matches the existing man page description on socket(7) which mentions
the argument being an interface name.
If the value has not been set, zero is returned and optlen will be set to zero
to indicate there is no interface name present.
Added a seqlock to protect this code path, and dev_ifname(), from someone
changing the device name via dev_change_name().
v2: Added seqlock protection while copying device name.
v3: Fixed word wrap in patch.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is detected on a PCIe device which does not have an
AER-aware driver, prevent AER infrastructure from reporting
successful error recovery.
This is because the report_error_detected() function that gets
called in the first phase of recovery process allows forward
progress even when the driver for the device does not have AER
capabilities. It seems that all callbacks (in pci_error_handlers
structure) registered by drivers that gets called during error
recovery are not mandatory. So the intention of the infrastructure
design seems to be to allow forward progress even when a specific
callback has not been registered by a driver. However, if error
handler structure itself has not been registered, it doesn't make
sense to allow forward progress.
As a result of the current design, in the case of a single device
having an AER-unaware driver or in the case of any function in a
multi-function card having an AER-unaware driver, a successful
recovery is reported.
Typical scenario this happens is when a PCI device is detached
from a KVM host and the pci-stub driver on the host claims the
device. The pci-stub driver does not have error handling capabilities
but the AER infrastructure still reports that the device recovered
successfully.
The changes proposed here leaves the device(s)in an unrecovered state
if the driver for the device or for any device in the subtree
does not have error handler structure registered. This reflects
the true state of the device and prevents any partial recovery (or no
recovery at all) reported as successful.
[bhelgaas: changelog]
Signed-off-by: Vijay Mohan Pandarathil <vijaymohan.pandarathil@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linas Vepstas <linasvepstas@gmail.com>
Reviewed-by: Myron Stowe <myron.stowe@redhat.com>
PAD is acpi Processor Aggregator Device which provides a control point
that enables the platform to perform specific processor configuration
and control that applies to all processors in the platform.
This patch is to implement Xen acpi pad logic. When running under Xen
virt platform, native pad driver would not work. Instead Xen pad driver,
a self-contained and thin logic level, would take over acpi pad logic.
When acpi pad notify OSPM, xen pad logic intercept and parse _PUR object
to get the expected idle cpu number, and then hypercall to hypervisor.
Xen hypervisor would then do the rest work, say, core parking, to idle
specific number of cpus on its own policy.
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The MPC5121 BSP comes with a gamma_set utility that initializes the gamma
table via an ioctl. Unfortunately, the ioctl number that utility uses
is defined improperly, but we can still support it.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch adds support for skb mark matching and set action.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs). Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline. This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.
The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.
Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.
In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.
The SRIOV related flow is as follows
1. the PPF does the detection of the new capabilities using
QUERY_DEV_CAP command.
2. the PPF activates the new capabilities using INIT_HCA.
3. the VF detects if the PPF activated the capabilities using
QUERY_HCA, and if this is the case activates them for itself too.
Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP. Steps 1 and 2 apply also for native mode.
User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.
In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add definitions for the VHT MCS support values that
are used to indicate, for each number of streams
(1 through 8) which MCSes are supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for reporting and calculating VHT MCSes.
Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch moves shirq interrupt controllers driver and header file out of
plat-spear directory. It is moved to drivers/irqchip/ directory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
I got below build warning while compiling this driver.
It's obviously RC5T583_MAX_INTERRUPT_MASK_REGS is 9 but irq_en_add
array only has 8 elements.
CC drivers/mfd/rc5t583-irq.o
drivers/mfd/rc5t583-irq.c: In function 'rc5t583_irq_sync_unlock':
drivers/mfd/rc5t583-irq.c:227: warning: array subscript is above array bounds
drivers/mfd/rc5t583-irq.c: In function 'rc5t583_irq_init':
drivers/mfd/rc5t583-irq.c:349: warning: array subscript is above array bounds
Since the number of interrupt enable registers is 8, this patch adds
define for RC5T583_MAX_INTERRUPT_EN_REGS to fix this bug.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the intruction of patch, eff607fdb1,
it became possible to include a governor as a module.
Thus the #ifdef statement for a governor should become #if IS_ENABLED.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Make it possible to ask the routines used for adding/removing devices
to/from the general ACPI PM domain, acpi_dev_pm_attach() and
acpi_dev_pm_detach(), respectively, to change the power states of
devices so that they are put into the full-power state automatically
by acpi_dev_pm_attach() and into the lowest-power state available
automatically by acpi_dev_pm_detach().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the bit definitions for VIDCON0_VIDOUT_WB.
These definitions are used to support writeback for RGB and
i80 interface. Also, output format of writeback is YUV444.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
The bit definitions for DITHMODE registers are moved according to
address order. Also, the bit definition of VIDCON1_FSTATUS_EVEN
is moved.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch cleans the bit definition for WINCON register.
The bit definition for WINCON1 and WINCON2 is removed, because
it is not used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch adds extension to videobuf2-core. It allow to export an mmap buffer
as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to V4L2 api. A new ioctl VIDIOC_EXPBUF is added. The
ioctl is used to export an mmap buffer as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let mmap method to use dma_mmap_coherent call. Moreover, this patch removes
vb2_mmap_pfn_range from videobuf2 helpers as it was suggested by Laurent
Pinchart. The function is no longer used in vb2 code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for prepare/finish callbacks in VB2 allocators. These
callback are used for buffer flushing.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for DMABUF memory type in videobuf2. It calls relevant
APIs of dma_buf for v4l reqbuf / qbuf / dqbuf operations.
For this version, the support is for videobuf2 as a user of the shared buffer;
so the allocation of the buffer is done outside of V4L2. [A sample allocator of
dma-buf shared buffer is given at [1]]
[1]: Rob Clark's DRM:
https://github.com/robclark/kernel-omap4/commits/drmplane-dmabuf
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds DMABUF memory type to v4l framework. Also adds the related file
descriptor in v4l2_plane and v4l2_buffer.
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple build regression fix for DT device drivers on Sparc. An earlier
change had masked out the of_iomap() helper on SPARC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yKFc
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree regression fix from Grant Likely:
"Simple build regression fix for DT device drivers on Sparc. An
earlier change had masked out the of_iomap() helper on SPARC."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of/address: sparc: Declare of_iomap as an extern function for sparc again
This bug-fix makes sure that of_iomap is defined extern for sparc so that the
sparc-specific implementation of_iomap is once again used when including
include/linux/of_address.h in a sparc context. OF_GPIO that is now available for
sparc relies on this.
The bug was inadvertently introduced in a850a75, "of/address: add empty static
inlines for !CONFIG_OF", that added a static dummy inline for of_iomap when
!CONFIG_OF_ADDRESS. However, CONFIG_OF_ADDRESS is never defined for sparc, but
there is a sparc-specific implementation /arch/sparc/kernel/of_device_common.c.
This fix takes the same approach as 0bce04b that solved the equivalent problem
for of_address_to_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
Pull networkign fixes from David Miller:
"Networking bug fixes, Cacio e Pepe edition:
1) BNX2X accidently accesses chip rev specific registers without an
appropriate guard, fix from Ariel Elior.
2) When we removed the routing cache, we set ip_rt_max_size to ~0 just
to keep reporting a value to userspace via sysfs. But the ipv4
IPSEC layer was using this to tune itself which is completely bogus
to now do. Fix from Steffen Klassert.
3) Missing initialization in netfilter ipset code from Jozsef
Kadlecsik.
4) Check CTA_TIMEOUT_NAME length properly in netfilter cttimeout code,
fix from Florian Westphal.
5) After removing the routing cache, we inadvertantly are caching
multicast routes that end up looping back locally, we cannot do
that legitimately any more. Fix from Julian Anastasov.
6) Revert a race fix for 8139cp qemu/kvm that doesn't actually work
properly on real hardware. From Francois Romieu.
7) Fixup errors in example command lines in VXLAN device docs."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
ipv4: do not cache looped multicasts
netfilter: cttimeout: fix buffer overflow
netfilter: ipset: Fix range bug in hash:ip,port,net
xfrm: Fix the gc threshold value for ipv4
If FREEZER is not defined, the error as following will be throw
when compiled.
arch/arm/kernel/signal.c:645: error: implicit declaration of function
'try_to_freeze_nowarn'
Signed-off-by: Haifeng Li <omycle@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is better style as platform data is supposed to be discardable after
init (though hotplug usually prevents this) and will ease implementation
of device tree property bindings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
ACPI 5 introduced I2cSerialBus resource that makes it possible to enumerate
and configure the I2C slave devices behind the I2C controller. This patch
adds helper functions to support I2C slave enumeration.
An ACPI enabled I2C controller driver only needs to call acpi_i2c_register_devices()
in order to get its slave devices enumerated, created and bound to the
corresponding ACPI handle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
AS3711 is a PMIC with multiple DCDC and LDO power supplies, GPIOs, an RTC,
a battery charger and a general purpose ADC. This patch adds support for
the MFD with support for a regulator driver and a backlight driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
Steffen Klassert says:
====================
This pull request is intended for 3.7 and contains a single patch to
fix the IPsec gc threshold value for ipv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a set of four bug fixes. The isci one is an obvious thinko (using
request buffer instead of response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because they're part
of a series of ten patches, the other seven of which went into the block layer
during the merge window meaning our current DIF/DIX implementation is broken
without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQre/4AAoJEDeqqVYsXL0MrxwH/A+b3aYvany+ZPg+elAFBCFm
3qHJ2Bys+M/kTkb0Fqb/l1KQfGFjooqcozm6eTgIeZ67bK947pxzu4Txy4JmeXvC
cHQ2lzEzcIFjiyVqV0tQ/wxMCnHTeqDx1WX02aw3T6e5JxObe+gC1pAEoMz2unSk
kpsSvFKBfCBMY6bmbVY5c2vpFTgD4UKtBiKn/GKtLtIDvynRx0P5e7/TNawxUB64
QZ/tu3Z2Ov5g9VWod+LpQwjVI+bIBlBEV4Of+91zou64aocrqXtSoky+ae9mwfPy
7KLLZzz5Fzc5KwT8ynEECtU2iFQXJ/zXNDRh7gBffc0ReljpuouOvIgqdZEW8d0=
=kQyb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four bug fixes.
The isci one is an obvious thinko (using request buffer instead of
response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because
they're part of a series of ten patches, the other seven of which went
into the block layer during the merge window meaning our current
DIF/DIX implementation is broken without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: Implement support for WRITE SAME
[SCSI] sd: Permit merged discard requests
[SCSI] Add a report opcode helper
[SCSI] isci: copy fis 0x34 response into proper buffer
Pull drm fixes from Dave Airlie.
Small fixes for (mostly Nouveau, some radeon) regressions.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use the correct fence implementation for nv50
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Yet again like previous two commits, drop the old hwdep user-space
firmware code from vx driver (snd-vxpocket and snd-vx222).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With priomap expansion no longer depending on knowing max id
allocated, netprio_cgroup can use cgroup->id insted of cs->prioidx.
Drop prioidx alloc/free logic and convert all uses to cgroup->id.
* In cgrp_css_alloc(), parent->id test is moved above @cs allocation
to simplify error path.
* In cgrp_css_free(), @cs assignment is made initialization.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As thermal drivers can be built as modules and also
the thermal framework itself, building cpu cooling
only as built-in can cause linking errors. For instance:
* Generic Thermal sysfs driver
*
Generic Thermal sysfs driver (THERMAL) [M/n/y/?] m
generic cpu cooling support (CPU_THERMAL) [N/y/?] (NEW) y
with the following drive:
CONFIG_OMAP_BANDGAP=m
generates:
ERROR: "cpufreq_cooling_unregister" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
ERROR: "cpufreq_cooling_register" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
This patch changes cpu cooling driver to allow it
to be built as module.
Reported-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There are predefined cpu_masks that are const data structures.
This patch changes the cpu cooling register function so that
those const cpu_masks can be used, without compilation warnings.
include/linux/cpumask.h
* The following particular system cpumasks and operations manage
* possible, present, active and online cpus.
*
* cpu_possible_mask- has bit 'cpu' set iff cpu is populatable
* cpu_present_mask - has bit 'cpu' set iff cpu is populated
* cpu_online_mask - has bit 'cpu' set iff cpu available to scheduler
* cpu_active_mask - has bit 'cpu' set iff cpu available to migration
*
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add register definitions used in several Exar PCI/PCIe UARTs
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs.
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will allow to use gpio for chip select with no modification in the
driver binding
When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we have valid flag to represent if this ACPI device power
state is valid. A device power state is valid does not necessarily
mean we, as OSPM, has a mean to put the device into that power state,
e.g. D3 cold is always a valid power state for any ACPI device, but if
there is no _PS3 or _PRx for this device, we can't really put that
device into D3 cold power state. The same is true for D0 power state.
So here comes the os_accessible flag, which is only set if the device
has provided us the required means to put it into that power state,
e.g. if we have _PS3 or _PRx, we can put the device into D3 cold state
and thus, D3 cold power state's os_accessible flag will be set in this
case.
And a new wrapper inline function is added to be used to check if
firmware has provided us a way to power off the device during runtime.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces acpi_handle_<level>(), where <level> is
a kernel message level such as err/warn/info, to support improved
logging messages for ACPI, esp. hot-plug operations.
acpi_handle_<level>() appends "ACPI" prefix and ACPI object path
to the messages. This improves diagnosis of hotplug operations
since an error message in a log file identifies an object that
caused an issue. This interface acquires the global namespace
mutex to obtain an object path. In interrupt context, it shows
the object path as <n/a>.
acpi_handle_<level>() takes acpi_handle as an argument, which is
passed to ACPI hotplug notify handlers from the ACPICA. Therefore,
it is always available unlike other kernel objects, such as device.
For example:
acpi_handle_err(handle, "Device don't exist, dropping EJECT\n");
logs an error message like this at KERN_ERR.
ACPI: \_SB_.SCK4.CPU4: Device don't exist, dropping EJECT
ACPI hot-plug drivers can use acpi_handle_<level>() when they need
to identify a target ACPI object path in their messages, such as
error cases. The usage model is similar to dev_<level>().
acpi_handle_<level>() can be used when a device is not created or
is invalid during hot-plug operations. ACPI object path is also
consistent on the platform, unlike device name that gets incremented
over hotplug operations.
ACPI drivers should use dev_<level>() when a device object is valid.
Device name provides more user friendly information, and avoids
acquiring the global ACPI namespace mutex. ACPI drivers also
continue to use pr_<level>() when they do not need to specify device
information, such as boot-up messages.
Note: ACPI_[WARNING|INFO|ERROR]() are intended for the ACPICA and
are not associated with the kernel message level.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Vijay Mohan Pandarathil <vijaymohan.pandarathil@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4591
Acked-by: Florian Fainelli <florian@openwrt.org>
The GPIOs are access through some registers in the chip common core or
over extif. We need locking around these GPIO accesses, all GPIOs are
accessed through the same registers and parallel writes will cause
problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4590
Acked-by: Florian Fainelli <florian@openwrt.org>
Add functions to access the GPIO registers for pullup and pulldown.
These are needed for handling gpio registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4589
Acked-by: Florian Fainelli <florian@openwrt.org>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4587
Acked-by: Florian Fainelli <florian@openwrt.org>
Add functions to access the GPIO registers for pullup and pulldown.
These are needed for handling gpio registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4586
Acked-by: Florian Fainelli <florian@openwrt.org>
The GPIOs are access through some registers in the chip common core.
We need locking around these GPIO accesses, all GPIOs are accessed
through the same registers and parallel writes will cause problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4585
Acked-by: Florian Fainelli <florian@openwrt.org>
From Michal Simek:
This branch depends on arm-soc devel/debug_ll_init branch because
we needed Rob's "ARM: implement debug_ll_io_init()"
(sha1: afaee03511ba8002b26a9c6b1fe7d6baf33eac86)
patch.
This branch also depends on zynq/dt branch because of previous major
zynq changes.
zynq/cleanup branch is subset of zynq/dt.
* 'zynq/multiplatform' of git://git.monstr.eu/linux-2.6-microblaze:
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Add/add conflict in arch/arm/Kconfig.debug.
Signed-off-by: Olof Johansson <olof@lixom.net>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ARM IM-PD1 add-on module has a few clock of its own, let's
move also these down to the drivers/clk/versatile driver dir
and get rid of any remaining oldschool Integrator clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is required for some of the clps711x series, so we're bringing in
the dependency explicitly.
By Linus Walleij (5) and others
via Linus Walleij
* depends/gpio-devel:
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
gpio/em: convert to linear IRQ domain
gpio/mvebu: convert to use irq_domain_add_simple()
gpio/tegra: convert to use linear irqdomain
gpiolib: unlock on error in gpio_export()
gpiolib: add gpio get direction callback support
GPIO: clps711x: Fix direction logic for PORTD
GPIO: clps711x: Fix return value for gpio_clps711x_get
gpiolib: Refactor gpio_export
GPIO: vt8500: Add extended gpio bank for WM8505/WM8650
gpio: clps711x: delete local <mach/gpio.h> header
GPIO: Add support for GPIO on CLPS711X-target platform
DA9055 GPIO driver
gpio/gpio-omap: Use existing pointer to struct device
gpio/gpio-pl061: Covert to use devm_* functions
Signed-off-by: Olof Johansson <olof@lixom.net>
Warnings were generated because of the following commit changed data type for
address pointer
195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors
add __iomem annotation to fix following warnings
drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’:
drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing
argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default]
arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile
void *’ but argument is of type ‘long unsigned int’
This patch stores the ioremap_nocache() returned address in a
void __iomem * instead of a unsigned long and passes the same to
readl/writel functions which fixes the above warnings.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update contact information to correspond my e-mail address changes.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is easier fro humans to understand decimal numbers than hexadecimals when
they are used as indexes.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use enum list for the module definitions (TWL4030_MODULE_*) which will ease
up future work with the IDs.
At the same time group the IDs in block of five so it is easier to find the
ID we are looking for (to count the number they stand for).
At the same time define TWL_MODULE_LED so client drivers can switch to use
it as soon as it is possible.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
AUDIO and MADC only available on twl4030 series and the TWL_MODULE_* mapping
is not needed.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Retu is a multi-function device found on Nokia Internet Tablets
implementing at least watchdog, RTC, headset detection and power button
functionality.
This patch implements minimum functionality providing register access,
IRQ handling and power off functions.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the regmap irq framework for implementing TPS65090 interrupt
support in place of implementing it locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since tps65090 register is accessed via regmap, moving
the register access APIs to header and making it as inline.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove unused member from tps65090 data structure as
these are not used.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. The device provides five configurable
step-down converters, 11 general purpose LDOs, USB OTG Module,
ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with
Power Path from USB, 32K clock generator.
Add the mfd core driver for TPS80031/TPS80032.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The channel field stores the LCDC channel corresponding to the MIPI-DSI
transmitter. The information is currently obtained through the lcd_chan
field that will be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From Pawel Moll:
* 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove motherboard dependencies in the DTS files
ARM: vexpress: Start using new Versatile Express infrastructure
ARM: vexpress: Add config bus components and clocks to DTs
mfd: Versatile Express system registers driver
mfd: Versatile Express config infrastructure
From Mike Turquette:
* depends/clk:
clk: Common clocks implementation for Versatile Express
clk: Versatile Express clock generators ("osc") driver
CLK: clk-twl6040: Initial clock driver for OMAP4+ McPDM fclk clock
clk: fix return value check in sirfsoc_of_clk_init()
clk: fix return value check in of_fixed_clk_setup()
clk: ux500: Update sdmmc clock to 100MHz for u8500
clk: ux500: Support prcmu ape opp voltage clock
mfd: dbx500: Export prmcu_request_ape_opp_100_voltage
clk: Don't return negative numbers for unsigned values with !clk
clk: Fix documentation typos
clk: Document .is_enabled op
clk: SPEAr: Vco-pll: Fix compilation warning
From Stephen Warren:
ARM: tegra: core SoC code enhancements
Various small clock initialization table and driver changes to support
WiFi modules, SPI controllers, and host1x (graphics/display hardware).
Various AHB/APB-related clocks were added to the Tegra30 clock driver.
The level 2 cache initialization is now driven by data from device tree,
and the cache configuration tweaked.
AUXDATA is added to support SPI controllers and host1x.
Code to decode Tegra's "speedo" process identification fuses is added.
This pull request is based on tegra-for-3.8-cleanup.
* tag 'tegra-for-3.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (26 commits)
ARM: tegra: Add Tegra30 host1x clock support
ARM: tegra: Add AUXDATA for Tegra30 host1x
ARM: tegra: Add Tegra20 host1x clock support
ARM: tegra: Add AUXDATA for Tegra20 host1x
ARM: tegra: Tegra30 speedo-based process identification
ARM: tegra: Add speedo-based process identification
ARM: tegra: flexible spare fuse read function
ARM: tegra: Implement 6395/1 for Tegra
ARM: tegra: Add OF_DEV_AUXDATA for sflash driver in board dt
ARM: tegra: enable data prefetch on L2
ARM: tegra: Add OF_DEV_AUXDATA for SLINK driver in board dt
ARM: tegra: common: using OF api for L2 cache init
ARM: tegra: dt: add L2 cache controller
ARM: tegra30: clocks: add AHB and APB clocks
ARM: tegra: set up wlan clocks for tegra dt
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
...
avoids needs for CONFIG_REGULATOR in sdhci.c
Signed-off-by: Philip Rakity <prakity@nvidia.com>
Reviewed-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be crystal clear on what the arguments mean in this
funtion dealing with both GPIO and PIN ranges with confusing
naming, we now have gpio_offset and pin_offset and we are
on the clear that these are offsets into the specific GPIO
and pin controller respectively. The GPIO chip itself will
of course keep track of the base offset into the global
GPIO number space.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various cleanups and enhancements are made to core Tegra code towards the
aim of including Tegra in a multi-platform ARM kernel:
RTC, timer, and TWD are configured via device tree.
SPARSE_IRQ is enabled.
Tegra's debug_ll options are simplified, and the macros brought into
line with other multi-platform implementations, and moved to the new
common location.
Two headers still need to be eliminated in order to include Tegra in a
multi-platform kernel/ <mach/{clk,powergate}.h>. A new common API needs
to be invented to replace parts of clk.h. powergate.h might be replaced
by regulators; this needs more investigation.
This pull request is based on tegra-for-3.8-dt, followed by a merge of
arm-soc's devel/debug_ll_init branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qXVf
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-single-zimage' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/multiplatform
From Stephen Warren:
ARM: tegra: single-zImage preparation work
Various cleanups and enhancements are made to core Tegra code towards the
aim of including Tegra in a multi-platform ARM kernel:
RTC, timer, and TWD are configured via device tree.
SPARSE_IRQ is enabled.
Tegra's debug_ll options are simplified, and the macros brought into
line with other multi-platform implementations, and moved to the new
common location.
Two headers still need to be eliminated in order to include Tegra in a
multi-platform kernel/ <mach/{clk,powergate}.h>. A new common API needs
to be invented to replace parts of clk.h. powergate.h might be replaced
by regulators; this needs more investigation.
This pull request is based on tegra-for-3.8-dt, followed by a merge of
arm-soc's devel/debug_ll_init branch.
* tag 'tegra-for-3.8-single-zimage' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (58 commits)
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
...
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ytxh
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aH3p
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup for 3.8
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
* tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
iommu: tegra: remove include of <mach/iomap.h>
staging: nvec: remove include of <mach/iomap.h>
crypto: tegra: remove include of <mach/clk.h>
ARM: tegra: update *.dts for regulator-compatible deprecation
usb: phy: tegra remove include of <mach/iomap.h>
usb: host: tegra remove include of <mach/iomap.h>
In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's stop spawning the pinctrl driver from the GPIO driver,
we have these two mechanisms broken apart now, and they can
each probe in isolation. If the GPIO driver cannot find its
pin controller (pinctrl-u300), the pin controller core will
tell it to defer probing.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a function to the pinctrl core to retrieve the GPIO
range associated with a certain pin for a certain controller.
This is needed when a pinctrl driver want to look up the
corresponding struct gpio_chip for a certain pin. As the
GPIO drivers can now create these ranges themselves, the
pinctrl driver no longer knows about all its associated GPIO
chips.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the function find_pinctrl_and_add_gpio_range()
to pinctrl_find_and_add_gpio_range() so as to be consistent
with the rest of the functions.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Like with commit 3c739ad0df
it is not always enough to specify all the pins of a gpio_chip
from offset zero to be added to a pin map range, since the
mapping from GPIO to pin controller may not be linear at all,
but need to be broken into a few consecutive sub-ranges or
1-pin entries for complicated cases. The ranges may also be
sparse.
This alters the signature of the function to accept offsets
into both the GPIO-chip local pinspace and the pin controller
local pinspace.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQqmPJAAoJEAf03oE53VmQbHEIAL7sxxa70NAZu0RnFq3iM0ic
B+zycq2wtVkjp1i9qWh47+xeF88JRINmYRjh4WIlnTJ3uDvK70H/dA7DUGQP0pbB
nTbaKInPnp1SOhyhfV1+3qxw8VNzNlvUQPunCP5ux9DJ1cwpfGn+d676I7l9skbe
91VEd+e9Sl1wdD6CfhtXGgAbi/y6UINj6CREK/HLVPzb6W2R6yFWDhKZLJRHKMCt
DxWXvHP8Vh+5/A9UoLtVR3PzG8yLCLN6Ty8ca25O2y/yTiEd+PpdfgwTS3tkBJ74
JhRl5pXdE7GmSvGvVdh1V3RN4anEKueJkuHnXomZiLR2E8mYg9S5ZmrScwQKpM4=
=B3yD
-----END PGP SIGNATURE-----
Merge tag 'at91-header' of git://github.com/at91linux/linux-at91 into next/headers
From Nicolas Ferre:
One fix related to UART for the "headers move" branch
* tag 'at91-header' of git://github.com/at91linux/linux-at91:
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCmwSAACgkQGxsu9jQV9nbssgCcChzwuFlPkP4sVdTtAGGh5mWD
rNcAn3PfG1ByMR57GkDtdQiAjS5N2dME
=Pi49
-----END PGP SIGNATURE-----
Merge tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner SoC support for 3.8
* tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux:
ARM: sunxi: Add entry to MAINTAINERS
ARM: sunxi: Add device tree for the A13 and the Olinuxino board
ARM: sunxi: Add earlyprintk support
ARM: sunxi: Add basic support for Allwinner A1x SoCs
irqchip: sunxi: Add irq controller driver
clocksource: sunxi: Add Allwinner A1X Timer Driver
clk: sunxi: Add dummy fixed rate clock for Allwinner A1X SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
The following pattern of code is tempting:
for_each_matching_node(np, table) {
match = of_match_node(table, np);
However, this results in iterating over table twice; the second time
inside of_match_node(). The implementation of for_each_matching_node()
already found the match, so this is redundant. Invent new function
of_find_matching_node_and_match() and macro
for_each_matching_node_and_match() to remove the double iteration,
thus transforming the above code to:
for_each_matching_node_and_match(np, table, &match)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Many of the regmap enabled drivers implementing one or more of the
readable, writeable, volatile and precious methods use the same code
pattern:
return ((reg >= X && reg <= Y) || (reg >= W && reg <= Z) || ...)
Switch to a data driven approach, using tables to describe
readable/writeable/volatile and precious registers ranges instead.
The table based check can still be overridden by passing the usual function
pointers via struct regmap_config.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current platform device creation and registration code in
acpi_create_platform_device() is quite convoluted. This function
takes an ACPI device node as an argument and eventually calls
platform_device_register_resndata() to create and register a
platform device object on the basis of the information contained
in that code. However, it doesn't associate the new platform
device with the ACPI node directly, but instead it relies on
acpi_platform_notify(), called from within device_add(), to find
that ACPI node again with the help of acpi_platform_find_device()
and acpi_platform_match() and then attach the new platform device
to it. This causes an additional ACPI namespace walk to happen and
is clearly suboptimal.
Use the observation that it is now possible to initialize the ACPI
handle of a device before calling device_add() for it to make this
code more straightforward. Namely, add a new field to struct
platform_device_info allowing us to pass the ACPI handle of interest
to platform_device_register_full(), which will then use it to
initialize the new device's ACPI handle before registering it.
This will cause acpi_platform_notify() to use the ACPI handle from
the device structure directly instead of using the .find_device()
routine provided by the device's bus type. In consequence,
acpi_platform_bus, acpi_platform_find_device(), and
acpi_platform_match() are not necessary any more, so remove them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid adding an ACPI handle pointer to struct device on
architectures that don't use ACPI, or generally when CONFIG_ACPI is
not set, in which cases that pointer is useless, define struct
acpi_dev_node that will contain the handle pointer if CONFIG_ACPI is
set and will be empty otherwise and use it to represent the ACPI
device node field in struct device.
In addition to that define macros for reading and setting the ACPI
handle of a device that don't generate code when CONFIG_ACPI is
unset. Modify the ACPI subsystem to use those macros instead of
referring to the given device's ACPI handle directly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ADIS16375, ADIS16480, ADIS16485, ADIS16488 6
degree to 10 degree of freedom IMUs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Factor out the code for parsing fixed point numbers into its own function and
make this function globally available. This allows us to reuse the code to parse
fixed point numbers in individual IIO drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for a new IIO channel type for pressure measurements.
This can for example be used for barometric pressure sensors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some of the newer generation devices from the ADIS16XXX series have more
registers than what can be supported with the current register addressing
scheme. These devices implement register paging to support a larger register
range. Each page is 128 registers large and the currently active page can be
selected via register 0x00 in each page. This patch implements transparent
paging inside the common adis library. The register read/write interface stays
the same and when a register is accessed the library automatically switches to
the correct page if it is not already selected. The page number is encoded in
the upper bits of the register number, e.g. register 0x5 of page 1 is 0x85.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In the event that an association exceeds its max_retrans attempts, we should
send an ABORT chunk indicating that we are closing the assocation as a result.
Because of the nature of the error, its unlikely to be received, but its a nice
clean way to close the association if it does make it through, and it will give
anyone watching via tcpdump a clue as to what happened.
Change notes:
v2)
* Removed erroneous changes from sctp_make_violation_parmlen
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the newer generation devices from the ADIS16XXX family have 32bit wide
register which spans two 16bit wide registers. This patch adds support for
reading and writing a 32bit wide register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Provide a IIO debugfs register access function for the ADIS library. This
function can be used by individual drivers to allow raw register access via
debugfs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch add the support of 6RD tunnels management via netlink.
Note that netdev_state_change() is now called when 6RD parameters are updated.
6RD parameters are updated only if there is at least one 6RD attribute.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides extensions to VXLAN for supporting Distributed
Overlay Virtual Ethernet (DOVE) networks. The patch includes:
+ a dove flag per VXLAN device to enable DOVE extensions
+ ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint
answers ARP requests from the local bridge on behalf of
remote DOVE clients
+ route short-circuiting (aka L3 switching). Known destination IP
addresses use the corresponding destination MAC address for
switching rather than going to a (possibly remote) router first.
+ netlink notification messages for forwarding table and L3 switching
misses
Changes since v2
- combined bools into "u32 flags"
- replaced loop with !is_zero_ether_addr()
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pool_size is always PAGE_SIZE, and since it is a software
configuration paramter (and not a hardware description parameter), we
cannot make it part of the Device Tree binding, so we'd better remove
it from the platform_data as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There is no need for the platform_data to give this ID, it is simply
the channel number, so we can compute it inside the driver when
registering the channels.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since we got rid of the per-XOR channel 'mv_xor' driver, now the
per-XOR engine driver that used to be called 'mv_xor_shared' can
simply be named 'mv_xor'.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
'struct mv_xor_shared_platform_data' used to be the platform_data
structure for the 'mv_xor_shared', but this driver is going to be
renamed simply 'mv_xor', so also rename its platform_data structure
accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
mv_xor_platform_data used to be the platform_data structure associated
to the 'mv_xor' driver. This driver no longer exists, and this data
structure really contains the properties of each XOR channel part of a
given XOR engine. Therefore 'struct mv_xor_channel_data' is a more
appropriate name.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that XOR channels are directly registered by the main
'mv_xor_shared' device ->probe() function and all users of the
'mv_xor' device have been removed, we can get rid of the latter.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Extend the XOR engine driver (currently called "mv_xor_shared") so
that XOR channels can be passed in the platform_data structure, and be
registered from there.
This will allow the users of the driver to be converted to the single
platform_driver variant of the mv_xor driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
'guarantee' is already removed from cgroup_task_migrate, so remove
the corresponding comments. Some other typos in cgroup are also
changed.
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
These are required for the clock infrastructure code to properly configure
and control the sta2x11 PLLs.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since there are now many sta2x11-mfd platform devices, using defines
for their names looks like a better solution.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A couple of predefined clocks (mux and gated) need to be
initialized with the virtual address of the clock's controlling
register and the address of a spinlock used to protect against
races.
This function exports such data for all the mfd cells.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A driver for the apb-soc registers is needed by the clock
infrastructure code to configure and control clocks on the sta2x11
chip.
Since some of the functions in sta2x11-mfd.c were almost identical
for the two existing platform devices, the following changes
have been performed to avoid further code duplication while
adding the apb-soc-regs driver:
* The sctl_regs and apbreg_regs fields in struct sta2x11_mfd
have been turned into just one array of pointers accessed by
device index.
* Platform probe methods have become one-liners invoking a
common probe with the device's index as second parameter.
* For loops have been inserted where the same operations
were performed for each of the two bars of a pci device.
* The apbreg_mask and sctl_mask functions were almost identical,
so they were turned into inline functions invoking a common
__sta2x11_mfd_mask() with the platform device's index as last
parameter. To do this, enum sta2x11_mfd_plat_dev has been declared in
sta2x11-mfd.h and more device types have been added to it.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the mfd cell to use the adc part of the Nano River Technologies
viperboard.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the mfd cell to use the gpio a and gpio b part
of the Nano River Technologies viperboard.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd driver for Nano River Technologies viperboard.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create a da9052-irq.c file so that it can handle interrupt related functions.
This is useful for allowing the da9052 drivers to use such functions
when dealing with da9052 interrupts.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In place of implementing the irq support in separate file,
moving implementation to main mfd file.
The irq files only contains the table and init steps only
and does not need extra file to have this only for this
purpose.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implement irq support of tps65910 with regmap irq framework
in place of implementing locally.
This reduces the code size significantly and easy to maintain.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow maps to replace the lock function for integration with dynamic
register accessability states.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KWk0
-----END PGP SIGNATURE-----
Merge tag 'lock' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into for-next
regmap: Customisable lock functions
Allow maps to replace the lock function for integration with dynamic
register accessability states.
Allow devfreq drivers to register a preferred governor name
and when the devfreq governor loads itself at a later point
required drivers are managed appropriately, at the time of
unload of a devfreq governor, stop managing those drivers
as well.
Since the governor structures do not need to be exposed
anymore, remove the definitions and make them static
NOTE: devfreq_list_lock is now used to protect governor
start and stop - as this allows us to protect governors and
devfreq with the proper dependencies as needed.
As part of this change, change the registration of exynos
bus driver to request for ondemand using the governor name.
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
[Merge conflict resolved by MyungJoo Ham]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Add devfreq_add_governor and devfreq_remove_governor which
can be invoked by governors to register with devfreq.
This sets up the stage to dynamically switch governors and
allow governors to be dynamically loaded as well.
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Useful for future dmaengine use.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds sysfs node which can be used to get information of frequency
transition. It represents transition table which contains total number of transition of
each freqeuncy state and time spent. It is inspired CPUFREQ's status driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
[Added Documentation/ABI entry, updated kernel-doc, and resolved merge conflict]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
struct parameters need to have ':' in documentation for
scripts/kernel-doc to parse appropriately.
Fix the errors reported by:
./scripts/kernel-doc include/linux/devfreq.h >/dev/null
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQj6QrAAoJEGFBu2jqvgRNn0gQAIr9rITJ0pg5KdUNLdEZE2yE
XjnkQWDF94KWvLhqj4rmYiPZDDCCaLSMgxbXizkJApmqwNeSX20MjeZmiURAXTva
AFNVa7CAHtO7oXIgk9bhZkkFk+VFHuGRNHHjO1kLbMr/pmfYJ16rgN0PB+PM9AkG
7bWP5F7Fd9wVkB4fmdrvTV0JdC5NquSmGUwnEQ9BCPoP89X4Flk3bSx2l5Q0aYN2
PwxTBlDwxZ59yoC7XqoHfox14M6G+0qd48tsT8yCxIyKNh1tNA02B9VIK6GT0fVL
Y0ya6SZBLDSDnRL3X9+NgGk9xdXDqRgEgLWsFulJrbB2RIBUzhZ/lVrusmYEhKLn
cCLuxrDjJj6T97fKpd/ZX0GDxldaAogjhNFqzAYLYAiGauSie7AXh1dg9iw5nkpJ
PV2FHpyWKShvhca5i+DlZbl4p4XohVp5H9v9gWuqSw68DTiT2qweq24g9n70279N
rmyI8mBcKfj0x040FPTZCNGwcSOxLfH6Q38ZTDWrkGeJEaWRm0VRTzMX7/zDXDPN
vy1cJdPmEXPUx6pmWhUN7dA25MOnsPOVpKpwB8bYBSWoPvj4navbw3S+YhoTS3G/
EJPvR0IpeiptLgBrOtUlqJrEPA2O3NEXqTeLD2y6DapMPInXw/Ta5l1B5XDd/a3V
tkJZCkmgBpRTLuEYfG05
=/FbB
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
These changes add DT boot support to DaVinci DA850
SoC.
* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: generate dtbs for da850 boards
ARM: davinci: add support for am1808 based EnBW CMC board
ARM: davinci: da850 evm: add DT data
ARM: davinci: da850: add SoC DT data
ARM: davinci: da850: add DT boot support
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
1) Support for PRUSS UIO driver for DA850 SoC
and related SRAM support updates.
2) Prepration for common clock migration
3) Serial support related changes for DA850 DT boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Z2vS
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/soc' of git://gitorious.org/linux-davinci/linux-davinci into next/soc
From Sekhar Nori:
SoC updates for DaVinci. Changes include:
1) Support for PRUSS UIO driver for DA850 SoC
and related SRAM support updates.
2) Prepration for common clock migration
3) Serial support related changes for DA850 DT boot
* tag 'davinci-for-v3.8/soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
This is similar to other platforms that don't allow command submission
to buffers locked on the cpu.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The mostly used lookup+get put+potential_destroy path of TTM objects
is converted to use RCU locks. This will substantially decrease the amount
of locked bus cycles during normal operation.
Since we use kfree_rcu to free the objects, no rcu synchronization is needed
at module unload time.
v2: Don't touch include/linux/kref.h
v3: Adapt to kref_get_unless_zero return value change
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function is intended to simplify locking around refcounting for
objects that can be looked up from a lookup structure, and which are
removed from that lookup structure in the object destructor.
Operations on such objects require at least a read lock around
lookup + kref_get, and a write lock around kref_put + remove from lookup
structure. Furthermore, RCU implementations become extremely tricky.
With a lookup followed by a kref_get_unless_zero *with return value check*
locking in the kref_put path can be deferred to the actual removal from
the lookup structure and RCU lookups become trivial.
v2: Formatting fixes.
v3: Invert the return value.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current FSI driver is using platform information pointer,
but it is not good design for DT support.
This patch makes master clock selection
independent from platform information pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
vmwgfx was its only user and always sets it to the same..
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's unused.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's unused.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers set it to 0 and nothing uses it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jumps in the vblank and page flip event timestamps cause trouble for
clients, so we should avoid them. The timestamp we get currently with
gettimeofday can jump, so use instead monotonic timestamps.
For backward compatibility use a module flag to revert back to using
gettimeofday timestamps. Add also a DRM_CAP_TIMESTAMP_MONOTONIC flag
that is simply a read only version of the module flag, so that clients
can query this without depending on sysfs.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Actually there's a reason this stuff is there, and it's called
commit e58f637bb9
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Aug 20 09:13:36 2010 +0100
drm/kms: Add a module parameter to disable polling
The idea has been that users can enable/disable polling at runtime. So
the quick hack has been to just re-enable the output polling if xrandr
asks for the latest state of the connectors.
The problem with that hack is that when we force connectors to another
state than what would be detected, we nicely ping-pong:
- Userspace calls probe, gets the forced state, but polling starts
again.
- Polling notices that the state is actually different, wakes up
userspace.
- Repeat.
As that commit already explains, the right fix would be to make the
locking more fine-grained, so that hotplug detection on one output
does not interfere with cursor updates on another crtc.
But that is way too much work. So let's just safe this gross hack by
caching the last-seen state of drm_kms_helper_poll for that driver,
and only fire up the poll engine again if it changed from off to on.
v2: Fixup the edge detection of drm_kms_helper_poll.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49907
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers already have a work item to run the hpd code, so we don't
need to launch a new one in the helper code. Dave Airlie mentioned
that the cancel+re-queue might paper over DP related hpd ping-pongs,
hence why this is split out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of reusing the polling code for hpd handling, split them up.
This has a few consequences:
- Don't touch HPD capable connectors in the poll loop.
- Only touch HPD capable connectors in drm_helper_hpd_irq_event.
- We could run the HPD handling directly (because all callers already
use their own work item), but for easier bisect that happens in it's
own patch.
The ultimate goal is that drivers grow some smarts about which
connectors have received a hotplug event and only call the detect code
of that connector. But that's a second step.
v2: s/hdp/hpd/, noticed by Adam Jackson. I can't type.
v3: Split out the work item removal as requested by Dave Airlie. This
results in a temporary mode_config.hpd_irq_work item to keep things
the same.
v4: In the hpd_irq_event handler don't bail out if other bits than HPD
are set. This is useful where e.g. hpd is unreliably, but mostly
works. Drivers can then set both HPD and POLL flags, and users get the
best of both worlds: Quick hotplug feedback if the hpd works, but
still reliable detection with the polling. The poll loop already works
the same, and doesn't bail if HPD is set.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useful if drivers want to be slightly more clever about hotplug
handling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A helper that drivers can use to send vblank event after a pageflip.
If the driver doesn't support proper vblank irq based time/seqn then
just pass -1 for the pipe # to get do_gettimestamp() behavior (since
there are a lot of drivers that don't use drm_vblank_count_and_time())
Also an internal send_vblank_event() helper for the various other code
paths within drm_irq that also need to send vblank events.
v1: original
v2: add back 'vblwait->reply.sequence = seq' which should not have
been deleted
v3: add WARN_ON() in case lock is not held and comments
v4: use WARN_ON_SMP() instead to fix issue with !SMP && !DEBUG_SPINLOCK
as pointed out by Marcin Slusarz
v5: update docbook
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds support for getting CEA Video ID Code for a given
display mode after matching with edid_cea_modes list. Its index in
the list added with one, gives the desired code.
This exported function will be used by hdmi drivers for composing
AVI info frame data.
Signed-off-by: Stephane Marchesin <marcheu@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
Highlights of this -next round:
- ivb fdi B/C fixes
- hsw sprite/plane offset fixes from Damien
- unified dp/hdmi encoder for hsw, finally external dp support on hsw
(Paulo)
- kill-agp and some other prep work in the gtt code from Ben
- some fb handling fixes from Ville
- massive pile of patches to align hsw VGA with the spec and make it
actually work (Paulo)
- pile of workarounds from Jesse, mostly for vlv, but also some other
related platforms
- start of a dev_priv reorg, that thing grew out of bounds and chaotic
- small bits&pieces all over the place, down to better error handling for
load-detect on gen2 (Chris, Jani, Mika, Zhenyu, ...)
On top of the previous pile (just copypasta):
- tons of hsw dp prep patches form Paulo
- round scheduled work items and timers to nearest second (Chris)
- some hw workarounds (Jesse&Damien)
- vlv dp support and related fixups (Vijay et al.)
- basic haswell dp support, not yet wired up for external ports (Paulo)
- edp support (Paulo)
- tons of refactorings to prepare for the above (Paulo)
- panel rework, unifiying code between lvds and edp panels (Jani)
- panel fitter scaling modes (Jani + Yuly Novikov)
- panel power improvements, should now work without the BIOS setting it up
- extracting some dp helpers from radeon/i915 and move them to
drm_dp_helper.c
- randome pile of workarounds (Damien, Ben, ...)
- some cleanups for the register restore code for suspend/resume
- secure batchbuffer support, should enable tear-free blits on gen6+
Chris)
- random smaller fixlets and cleanups.
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (231 commits)
drm/i915: Restore physical HWS_PGA after resume
drm/i915: Report amount of usable graphics memory in MiB
drm/i915/i2c: Track users of GMBUS force-bit
drm/i915: Allocate the proper size for contexts.
drm/i915: Update load-detect failure paths for modeset-rework
drm/i915: Clear unused fields of mode for framebuffer creation
drm/i915: Always calculate 8xx WM values based on a 32-bpp framebuffer
drm/i915: Fix sparse warnings in from AGP kill code
drm/i915: Missed lock change with rps lock
drm/i915: Move the remaining gtt code
drm/i915: flush system agent TLBs on SNB
drm/i915: Kill off now unused gen6+ AGP code
drm/i915: Calculate correct stolen size for GEN7+
drm/i915: Stop using AGP layer for GEN6+
drm/i915: drop the double-OP_STOREDW usage in blt_ring_flush
drm/i915: don't rewrite the GTT on resume v4
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
drm/i915: put ring frequency and turbo setup into a work queue v5
drm/i915: don't block resume on fb console resume v2
drm/i915: extract l3_parity substruct from dev_priv
...
The pn544.h just provides the platform data struct and defines and
nothing else. So move it to to linux/platform_data/ now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The majority of the defines and structures from pn544.h are no
longer in use. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.
While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Match the iio_buffer_register stub signature up to the real function and make
the second parameter const. This fixes a the following warnings if
CONFIG_IIO_BUFFER is disabled:
drivers/staging/iio/accel/adis16201_core.c: In function ‘adis16201_probe’:
drivers/staging/iio/accel/adis16201_core.c:536: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16203_core.c: In function ‘adis16203_probe’:
drivers/staging/iio/accel/adis16203_core.c:468: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16204_core.c: In function ‘adis16204_probe’:
drivers/staging/iio/accel/adis16204_core.c:527: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16209_core.c: In function ‘adis16209_probe’:
drivers/staging/iio/accel/adis16209_core.c:542: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16240_core.c: In function ‘adis16240_probe’:
drivers/staging/iio/accel/adis16240_core.c:588: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make perf build for x86 once the UAPI disintegration patches for that arch
have been applied by adding the appropriate -I flags - in the right order -
and then converting some #includes that use ../.. notation to find main kernel
headerfiles to use <asm/foo.h> and <linux/foo.h> instead.
Note that -Iarch/foo/include/uapi is present _before_ -Iarch/foo/include.
This makes sure we get the userspace version of the pt_regs struct. Ideally,
we wouldn't have the latter -I flag at all, but unfortunately we want
asm/svm.h and asm/vmx.h in builtin-kvm.c and these aren't part of the UAPI -
at least not for x86. I wonder if the bits outside of the __KERNEL__ guards
*should* be transferred there.
I note also that perf seems to do its dependency handling manually by listing
all the header files it might want to use in LIB_H in the Makefile. Can this
be changed to use -MD?
Note that to do make this work, we need to export and UAPI disintegrate
linux/hw_breakpoint.h, which I think should've been exported previously so that
perf can access the bits. We have to do this in the same patch to maintain
bisectability.
Signed-off-by: David Howells <dhowells@redhat.com>
Read Local OOB Data command can take more than 1 second on some chips.
e.g. on CSR 0a12:0001 first call to Read Local OOB Data after reset
takes about 1300ms resulting in tx timeout error.
[27698.368655] Bluetooth: hci0 command 0x0c57 tx timeout
2012-10-31 15:53:36.178585 < HCI Command: Read Local OOB Data (0x03|0x0057) plen 0
2012-10-31 15:53:37.496996 > HCI Event: Command Complete (0x0e) plen 36
Read Local OOB Data (0x03|0x0057) ncmd 1
status 0x00
hash 0x92219d9b447f2aa9dc12dda2ae7bae6a
randomizer 0xb1948d0febe4ea38ce85c4e66313beba
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
