The logic that checks if a device has remote control is wrong.
Due to that, the em28xx RC module is not loaded by default.
Fix the logic, in order to make it work properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This simply shows a little warning if the board does not have remote
control support. This should make it easier for users to see if they
have misconfigured their system or if the driver simply does not have
rc-support for their card (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cinergy HTC Stick HD uses the same remote control as the TerraTec
Cinergy XS products. Thus the same keymap could be re-used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the device is physically unplugged but there are still
open file handles, resource release is defered until last
opened handle is closed.
This patch fixes a missing em28xx_fh struct release.
Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the LNA amplifier also for DVB-T (like for DVB-T2 and DVB-C);
this greatly improves reception of weak signals without affecting the reception
of the strong ones.
Experimental data (collected with the mipsel STB) on the weakest frequencies
available in my area:
LNA OFF:
MUX level BER picture
RAI mux 4 72% 32000 corrupted
TIMB 2 75% 14 OK
TVA Vicenza 68% 32000 corrupted
RAI mux 2 78% 14 OK
LNA ON:
MUX level BER picture
RAI mux 4 73% 1500 OK
TIMB 2 76% 0 OK
TVA Vicenza 69% 0 OK
RAI mux 2 79% 0 OK
Moreover, with LNA enabled, the PCTV 290e was able to pick up 2 new frequencies
matching the integrated tuner of my Panasonic G20 TV, which is really good.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody ever waits on any of these wait_queue's,
so this patch removes them completely.
Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans namespace a bit by making em28xx_card_setup()
em28xx_pre_card_setup() static functions.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
media_build/v4l/au0828-video.c: In function 'au0828_irq_callback':
media_build/v4l/au0828-video.c:123:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx23888-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx23888-ir.c:334:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx25840-ir.c:319:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'cx25840_ir_tx_write':
media_build/v4l/cx25840-ir.c:863:21: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c: In function 'snd_em28xx_hw_capture_params':
media_build/v4l/em28xx-audio.c:346:31: warning: variable 'format' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:25: warning: variable 'rate' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:15: warning: variable 'channels' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-control.c: In function 'get_input_lines_info':
media_build/v4l/hdpvr-control.c:98:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-video.c: In function 'hdpvr_try_ctrl':
media_build/v4l/hdpvr-video.c:955:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/saa7134-video.c: In function 'saa7134_s_tuner':
media_build/v4l/saa7134-video.c:2030:6: warning: variable 'rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/sn9c102_core.c: In function 'sn9c102_stream_interrupt':
media_build/v4l/sn9c102_core.c:998:7: warning: variable 'timeout' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This used to be the default if the lock pointer was set, but now that lock is by
default only used for ioctl serialization. Those drivers that already used
core locking have this flag set explicitly, except for some drivers where
it was obvious that there was no need to serialize any file operations other
than ioctl.
The drivers that didn't need this flag were:
drivers/media/radio/dsbr100.c
drivers/media/radio/radio-isa.c
drivers/media/radio/radio-keene.c
drivers/media/radio/radio-miropcm20.c
drivers/media/radio/radio-mr800.c
drivers/media/radio/radio-tea5764.c
drivers/media/radio/radio-timb.c
drivers/media/video/vivi.c
sound/i2c/other/tea575x-tuner.c
The other drivers that use core locking and where it was not immediately
obvious that this flag wasn't needed were changed so that the flag is set
together with a comment that that driver needs work to avoid having to
set that flag. This will often involve taking the core lock in the fops
themselves.
Eventually this flag should go and it should not be used in new drivers.
There are a few reasons why we want to avoid core locking of non-ioctl
fops: in the case of mmap this can lead to a deadlock in rare situations
since when mmap is called the mmap_sem is held and it is possible for
other parts of the code to take that lock as well (copy_from_user()/copy_to_user()
perform a down_read(&mm->mmap_sem) when a page fault occurs).
It is very unlikely that that happens since the core lock serializes all
fops, but the kernel warns about it if lock validation is turned on.
For poll it is also undesirable to take the core lock as that can introduce
increased latency. The same is true for read/write.
While it was possible to make flags or something to turn on/off taking the
core lock for each file operation, in practice it is much simpler to just
not take it at all except for ioctl and leave it to the driver to take the
lock. There are only a handful fops compared to the zillion ioctls we have.
I also wanted to make it obvious which drivers still take the lock for all
fops, so that's why I chose to have drivers set it explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This functions are no longer used from another file,
so they should be declared as static.
Also is it necessary to move some of them before they
are used, since they are no longer header-declared.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is only used in em28xx-input.c so it
makes no sense to have it anywhere but in em28xx-input.c.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moving this helps isolating em28xx_input and will help
converting it into a separate module.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those functions will be needed by em28xx-input module, to be
added on the next patches.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dev->ctl_input() is always set before a call to video_mux(),
but then video_mux() sets it again with the same value.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of several unused parameters in struct em28xx_usb_isoc_ctl.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop the URBs in em28xx_stop_streaming(), so that em28xx_irq_callback()
cannot be called after the streaming has stopped.
This should eliminate the crashes reported by Antti Palosaari and the warnings
reported by Andy Furniss.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is applying some hunks that are already at changeset
c247d7b, causing a compilation breakage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is mostly copy/paste of the 520e code with setting GPIO7 removed
(no LED light).
I've worked on just released vanilla linux-3.3.0 kernel, so there may
be 1/2 lines offset to the internal working source, but most of the
code should apply cleanly.
I was able to get the DVB-C working (tuned and watched TV). Haven't
tested DVB-T (no signal atm).
Special thanks to everybody who worked on the code and to Antti
Palosaari and Devin Heitmueller who provided essential support on irc.
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
AVF4910 (not used atm)
Signed-off-by: Ivan Kalvachev <ikalvachev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is based of:
Empia EM2884
Micronas DRX 3926K
NXP TDA18271HDC2
... + analog parts.
Analog is not supported currently. Only DVB-T and DVB-C.
There seems to be still problems for locking DVB-C channels which have
strong signal. Attenuator helps. I think it is demodulator IF/RF AGC
issue. Lets fix it later. Patches are welcome.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is based of:
Empia EM2874B
Micronas DRX 3913KA2
NXP TDA18271HDC2
Only DVB-C supported currently since missing firmware.
According to my tests, DRX 3913KA2 demodulator requires firmware
in order to support DVB-T mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch saves 255 bytes of stack on usb_probe() by removing
a char array. In some platforms this is represents a substantial save.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These arrays were embedded in the struct itself, but they weren't
used by anyone, since urbs are now dinamically allocated
at em28xx_usb_isoc_ctl struct.
Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On MIPS/ARM set-top-boxes, as well as old x86 PCs, memory allocation failures
in the em28xx driver are common, due to memory fragmentation over time, that
makes impossible to allocate large chunks of coherent memory.
A typical system with 256/512 MB of RAM fails after just 1 day of uptime (see
the old thread for detailed reports and crashlogs).
In fact, the em28xx driver allocates memory for USB isoc transfers at runtime,
as opposite to the dvb-usb drivers that allocates the USB buffers when the
device is initialized, and frees them when the device is disconnected.
Moreover, in digital mode the USB isoc transfer buffers are freed, allocated
and cleared every time the user selects a new channel, wasting time and
resources.
This patch solves both problems by allocating DVB isoc transfer buffers in
em28xx_usb_probe(), and freeing them in em28xx_usb_disconnect().
In fact, the buffers size and number depend only on the max USB packet size
that is parsed from the USB descriptors in em28xx_usb_probe(), so it can
never change for a given device.
This approach makes no sense in analog mode (as the buffer size depends on
the alternate mode selected at runtime), the patch creates two separate sets
of buffers for digital and analog modes.
For digital-only devices, USB buffers are created when the device is probed
and freed when the device is disconnected.
For analog-only devices, nothing changes: isoc buffers are created at runtime.
For hybrid devices, two sets of buffers are maintained: the digital-mode
buffers are created when the device is probed, and freed when the device is
disconnected; analog-mode buffers are created/destroyed at runtime as before.
So, in analog mode, digital and analog buffers coexists at the same time: this
can be justified by the fact that digital mode is by far more commonly used
nowadays, so it makes sense to optimize the driver for this use case scenario.
The patch has been tested in the last few days on a x86 PC and a MIPS
set-top-box, with the PCTV 290e (digital only) and the Terratec Hybrid XS
(hybrid device). With the latter, I switched several times between analog and
digital mode (Kaffeine/TvTime) with no issue at all.
I unplugged/plugged the devices several times with no problem.
Also, after over 3 days of normal usage in the MPIS set-top-box, the PCTV 290e
was still up and running.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
This parameter is no longer used after multi-frontend to single-frontend change.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
The card definition of the Terratec Cinergy 200 USB uses the
wrong tuner type. Therefore some channels are currently missing.
Attached patch fixes this problem.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MaxPacketSize for em2800 based devices is too small to capture at full resolution.
Therefore scale down when the maximum frame size is selected.
The previous workaround that simply reduced the X resolution cannot be used
because it crops a part of the input as
the em2800 can only scale down with a factor of 0.5.
reverts commits 1ca31892e and fb3de0398a.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
writing the EM28XX_R06_I2C_CLK register leads to the problem that the
i2c bus on the Terratec Cinergy 200 USB is no longer usable when the
system is rebooted.
The device needs to be unplugged in order to bring it back to life.
Attached patch conditionally disables the write in
em28xx_pre_card_setup() like it is already done in em28xx_card_setup().
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It looks like the return value check that is done after setting the I2C
speed checks the wrong return code.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'struct em28xx *' pointer was passed by reference to the
em28xx_init_dev() function, for no reason. Instead, just pass it by
value, which is much more logical and simple.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for the Plextor ConvertX PX-AV100U, which uses the
eMPIA EM2820 chip. The device has a device_id of '0x093b, 0xa003'. I
am using the existing EM2820_BOARD_PINNACLE_DVC_90 board profile, as
the Pinnacle Dazzle DVC 90/100/101/107, Kaiser Baas Video to DVD
maker, and Kworld DVD Maker 2 were already mapped to it. Some more
background on the device and my testing can be found at
http://www.donkramer.net/plextor_122710.pdf
Signed-off-by: Don Kramer <dgkramer@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reworked device probing to get rid of hacks to guess the maximum size of
dvb iso transfer packets. The new code also selects the first alternate
config which supports the largest possible iso transfers for dvb.
[mchehab@redhat.com: Fix a few checkpatch.pl CodingStyle compliants]
Signed-off-by: Holger Nelson <hnelson@hnelson.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for the Honestech Vidbox NW03 USB capture device.
Signed-off-by: Gareth Williams <gareth@garethwilliams.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the Terratec Cinergy HTC USB XS which is similar to
the Terratec H5 by adding the USB-ids to the table. According to
http://linux.terratec.de it uses the same ICs and DVB-C works for me
using the firmware of the H5.
Signed-off-by: Holger Nelson <hnelson@hnelson.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix detection of EMP202 audio chip. Some versions have an id of
0x83847650 instead of 0xffffffff
Honestech Vidbox NW03 has a EMP202 audio chip with a different Vendor ID.
Apparently, it is the same with the Gadmei ITV380:
http://linuxtv.org/wiki/index.php/Gadmei_USB_TVBox_UTV380
Signed-off-by: Gareth Williams <gareth@garethwilliams.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating two DVB frontend entries for the same device,
create just one entry, and fill the delivery_system according with
the supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no need to initialize unused fields with zero, as Kernel does
it automatically.
Removing the initialization makes the code cleaner.
This also allows the removal of the unused pll_set callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
PCTV290E: Attach a single frontend, rather than a frontend each per
delivery system, whereby a multistandard frontend can advertise all
associated delivery systems.
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DRX-K doesn't change the delivery system at set_properties,
but do it at frontend init. This causes problems on programs like
w_scan that, by default, opens both frontends.
Instead, explicitly set the format when set_parameters callback is
called.
Tested-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
