I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f8: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a77 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
This has been a busy release for regmap. By far the biggest set of
changes here are those from Markus Pargmann which implement support for
block transfers in smbus devices. This required quite a bit of
refactoring but leaves us better able to handle odd restrictions that
controllers may have and with better performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV6cZyAAoJECTWi3JdVIfQM3sH/RSygzRIOoOuvro0U3qd4+nM
qLzpuZNtuAP7xNc5yJZiixz1S6PqUNl+pK/u58s6x10GWDGsWZY6E0Lg94lYmfhA
26jqWSzrMHp42x+ZN7btLExzPTVnvRerrjtj4mqz6t4yun9SzqVymaZTUZ1hqPHB
qxSNHs3rHPiqiEWpQKJXb+5dazYYJCbOUrlivxJCk60+ns1N88cA71aY+5/zq5uy
36e0iYe3s+lv0lptedarFCf9p7o1E6EQzhvEMfyquGXtvq8fl7Qdeo7riRFQ8Iiy
sygCb3AYuZIiqnOC7+90xkr2Oq0iwdJUD91A9sl/SRiwgItG9jW03bWNHYIhQyk=
=CbGt
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
Commit cf736ea6f9 ("thermal: power_allocator: do not use devm*
interfaces") forgot to change a devm_kcalloc() to just kcalloc(), but
it's corresponding devm_kfree() was changed to kfree(). Allocate with
kcalloc() to match the kfree().
Fixes: cf736ea6f9 ("thermal: power_allocator: do not use devm* interfaces")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
policy->max is the maximum allowed frequency defined by user and
clipped_freq is the maximum that thermal constraints allow.
If clipped_freq is lower than policy->max, then we need to readjust
policy->max.
But, if clipped_freq is greater than policy->max, we don't need to do
anything. We used to call cpufreq_verify_within_limits() in this case,
but it doesn't change anything in this case.
Lets skip this unnecessary call and write a comment that explains this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
That's what it is for, lets name it properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We just need to take care of single event here and there is no need to
increase indentation level of most of the code (which causes lines
longer that 80 columns to break).
Kill the switch block.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If a valid cpufreq_dev is found for policy->cpu, we should update the
policy and quit the for loop. There is no need to keep traversing the
list of cpufreq_dev's.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Its always set before getting used, don't initialize it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code in question is called outside of standard driver
probe()/remove() callbacks and thus will not benefit from use of devm*
infrastructure.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
regmap_init(...) is a macro since commit
"regmap: Use different lockdep class for each regmap init call".
That same name is used as a function pointer: prevent its expansion
by adding parentheses around the function pointer.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds a thermal driver for Wildcat Point platform controller
hub. This driver register PCH thermal sensor as a thermal zone and
associate critical and hot trips if present.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The code testing if a temperature should be emulated or not is
not obvious. Add a comment explaining why this test is done.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use IS_ENABLED(CONFIG_THERMAL_EMULATION) to make the code more readable
and to get rid of the addtional #ifdef around the variable definitions
in thermal_zone_get_temp().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When the thermal zone has no get_temp callback then thermal_zone_device_register()
calls thermal_zone_device_set_polling() with a polling delay of 0. This
only cancels the poll_queue. Since the poll_queue hasn't been scheduled this
is a no-op. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Linux thermal framework support to change thermal governor
policy in userspace, but it can't show what available policies
supported.
This patch adds available_policies attribute to the thermal
framework, it can list the thermal governors which can be
used for a particular zone. This attribute is read only.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add support for Intel Denlow UP server platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The exynos thermal driver use the of_thermal_*() API to parse the basic data
for thermal management from devicetree file. So, if CONFIG_EXYNOS_THERMAL is
selected without CONFIG_THERMAL_OF, kernel can build it without any problem.
But, exynos thermal driver is not working with following error log. This patch
add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF.
[ 1.458644] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.459096] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.465211] exynos4412_tmu_initialize: No CRITICAL trip point defined at of-thermal.c!
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe the regulator (if present) was enabled but not disabled in
case of failure. So an unsuccessful probe lead to enabling the
regulator which was actually not needed because the device was not
enabled.
Additionally each deferred probe lead to increase of regulator enable
count so it would not be effectively disabled during removal of the
device.
Test HW: Exynos4412 - Trats2 board
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 498d22f616 ("thermal: exynos: Support for TMU regulator defined at device tree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor uses ftrace to output a bunch of internal
data for debugging and tuning. Currently, the requested power it
outputs is the "weighted" requested power, that is, what each cooling
device has requested multiplied by the cooling device weight. It is
more useful to trace the real request, without any weight being
applied.
This commit only affects the data traced, there is no functional change.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull thermal management updates from Zhang Rui:
"Specifics:
- enhance Thermal Framework with several new capabilities:
* use power estimates
* compute weights with relative integers instead of percentages
* allow governors to have private data in thermal zones
* export thermal zone parameters through sysfs
Thanks to the ARM thermal team (Javi, Punit, KP).
- introduce a new thermal governor: power allocator. First in kernel
closed loop PI(D) controller for thermal control. Thanks to ARM
thermal team.
- enhance OF thermal to allow thermal zones to have sustainable power
HW specification. Thanks to Punit.
- introduce thermal driver for Intel Quark SoC x1000platform. Thanks
to Ong, Boon Leong.
- introduce QPNP PMIC temperature alarm driver. Thanks to Ivan T. I.
- introduce thermal driver for Hisilicon hi6220. Thanks to
kongxinwei.
- enhance Exynos thermal driver to handle Exynos5433 TMU. Thanks to
Chanwoo C.
- TI thermal driver now has a better implementation for EOCZ bit.
From Pavel M.
- add id for Skylake processors in int340x processor thermal driver.
- a couple of small fixes and cleanups."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: hisilicon: add new hisilicon thermal sensor driver
dt-bindings: Document the hi6220 thermal sensor bindings
thermal: of-thermal: add support for reading coefficients property
thermal: support slope and offset coefficients
thermal: power_allocator: round the division when divvying up power
thermal: exynos: Add the support for Exynos5433 TMU
thermal: cpu_cooling: Fix power calculation when CPUs are offline
thermal: cpu_cooling: Remove cpu_dev update on policy CPU update
thermal: export thermal_zone_parameters to sysfs
thermal: cpu_cooling: Check memory allocation of power_table
ti-soc-thermal: request temperature periodically if hw can't do that itself
ti-soc-thermal: implement eocz bit to make driver useful on omap3
cleanup ti-soc-thermal
thermal: remove stale THERMAL_POWER_ACTOR select
thermal: Default OF created trip points to writable
thermal: core: Add Kconfig option to enable writable trips
thermal: x86_pkg_temp: drop const for thermal_zone_parameters
of: thermal: Introduce sustainable power for a thermal zone
thermal: add trace events to the power allocator governor
thermal: introduce the Power Allocator governor
...
This patch adds the support for hisilicon thermal sensor, within
hisilicon SoC. there will register sensors for thermal framework
and use device tree to bind cooling device.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In order to avoid having each driver adding their own
specific DT property to specify slope and offset,
this patch adds a basic coefficient reading from
DT thermal zone node. Right now, as the thermal
framework does not support multiple sensors,
the current coefficients apply only to the only
sensor in the thermal zone.
The supported equation is a simple linear model:
slope * <sensor reading> + offset.
slope and offset are read from the coefficients
DT property. In the same way as it is described in
the DT thermal binding.
So, as of today, the thermal framework will support
only cases like:
/* hotspot = 1 * adc + 6000 */
coefficients = <1 6000>;
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It is common to have a linear extrapolation from
the current sensor readings and the actual temperature
value. This is specially the case when the sensor
is in use to extrapolate hotspots.
This patch adds slope and offset constants for
single sensor linear extrapolation equation. Because
the same sensor can be use in different locations,
from board to board, these constants are added
as part of thermal_zone_params.
The constants are available through sysfs.
It is up to the device driver to determine
the usage of these values.
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In situations where there is an uneven number of cooling devices, the
division of power among them can lead to a milliwatt being dropped on
the floor due to rounding errors. This doesn't sound like a lot, but
some devices only grant the lowest cooling device state for their
maximum power. So for instance, if the granted_power is the maximum
power and all devices are getting their maximum power, one would get
max_power - 1, making it choose cooling device state 1, instead of 0.
Round the division to make the calculation more accurate.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is a copy and paste bug, "->clk" vs "->pclk", so we return the
wrong error code here.
Fixes: cbac8f6394 ('thermal: rockchip: add driver for thermal')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Package C8 to C10 was introduced in newer Intel CPUs, we need to
include them in the package c-state residency calculation.
Otherwise, idle injection target is not accurately maintained by
the closed control loop.
Also cleaned up the code to make it scale better with large number
of c-states.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Broadwell server has support for package C-states, idle injection works
as expected on this platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mark the module init / exit functions with __init / __exit accodingly.
This allows making the intel_powerclamp_ids[] array __initconst, too, as
it only gets referenced from powerclamp_probe(). This is safe as
file2alias doesn't care about the section, but the symbol name for the
MODULE_DEVICE_TABLE alias.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
DESCRIPTION
Spurious Thermal Alert: Talert can happen randomly while the device remains
under the temperature limit defined for this event to trig. This spurious
event is caused by a incorrect re-synchronization between clock domains.
The comparison between configured threshold and current temperature value
can happen while the value is transitioning (metastable), thus causing
inappropriate event generation. No spurious event occurs as long as the
threshold value stays unchanged. Spurious event can be generated while a
thermal alert threshold is modified in
CONTROL_BANDGAP_THRESHOLD_MPU/GPU/CORE/DSPEVE/IVA_n.
WORKAROUND
Spurious event generation can be avoided by performing following sequence
when the threshold is modified:
1. Mask the hot/cold events at the thermal IP level.
2. Modify Threshold.
3. Unmask the hot/cold events at the thermal IP level.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Bandgap Temperature read Dtemp can be corrupted
DESCRIPTION
Read accesses to registers listed below can be corrupted due to
incorrect resynchronization between clock domains.
Read access to registers below can be corrupted :
• CTRL_CORE_DTEMP_MPU/GPU/CORE/DSPEVE/IVA_n (n = 0 to 4)
• CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA_n
WORKAROUND
Multiple reads to CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA[9:0]:
BGAP_DTEMPMPU/GPU/CORE/DSPEVE/IVA is needed to discard false value and
read right value:
1. Perform two successive reads to BGAP_DTEMP bit field.
(a) If read1 returns Val1 and read2 returns Val1, then
right value is Val1.
(b) If read1 returns Val1, read 2 returns Val2, a third
read is needed.
2. Perform third read
(a) If read3 returns Val2 then right value is Val2.
(b) If read3 returns Val3, then right value is Val3.
The above in gist means if val1 and val2 are the same then we can go
ahead with that value else we need a third read which will be right
since synchronization will be complete by then.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds the support for Exynos5433's TMU (Thermal Management Unit).
Exynos5433 has a little different register bit fields as following description:
- Support the eight trip points for rising/falling interrupt by using two registers
- Read the calibration type (1-point or 2-point) and sensor id from TRIMINFO register
- Use a little different register address
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Ensure that the CPU for which the frequency is being requested
is online. If none of the CPUs are online the requested power is
returned as 0.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It was initially understood that an update to the cpu_device
(cached in cpufreq_cooling_device) was required to ascertain the
correct operating point of the device on a cpufreq policy->cpu update
or creation or deletion of a cpufreq policy.
(e.g. when the existing policy CPU goes offline).
This update is not required and it is possible to ascertain the OPPs
from the leading CPU in a cpufreq domain even if the CPU is hotplugged out.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful for tuning to be able to edit thermal_zone_parameters from
userspace. Export them to the thermal_zone sysfs so that they can be
easily changed.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We allocate the power_table in memory but we don't test whether the
allocation succeeded. Return -ENOMEM if kcalloc() fails.
Fixes: e0128d8ab423 ("thermal: cpu_cooling: implement the power cooling device API")
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When periodic mode is not enabled, it is neccessary to force reads.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For omap3, proper implementation of eocz bit is needed. It was
actually a TODO in the driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Simplify code by removing goto's where they point to simple return.
Avoid confusing |= on error values.
Correct whitespace.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A previous version of this patch had a config for THERMAL_POWER_ACTOR
but it was dropped. Remove the select as it is not doing anything.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering a thermal zone from device tree, default the trip
points to writable. By default, only the root user can change these.
This allows the trip points to be tweaked after the system has
booted.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a Kconfig option to allow system integrators to control whether
userspace tools can change trip temperatures. This option overrides
the thermal zone setup in the driver code and must be enabled for
platform specified writable trips to come into effect.
The original behaviour of requiring root privileges to change trip
temperatures remains unchanged.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
8754d5115693 ("thermal: introduce the Power Allocator governor") dropped
the const attribute in the struct thermal_zone_device. That means that
the thermal_zone_params pointer passed to thermal_zone_device_register()
also lost the const qualifier. Drop the const in x86_pkg_temp_thermal.c
as well to avoid the following warning as reported by the kbuild test
robot:
drivers/thermal/x86_pkg_temp_thermal.c: In function 'pkg_temp_thermal_device_add':
>> drivers/thermal/x86_pkg_temp_thermal.c:450:31: warning: passing argument 6 of 'thermal_zone_device_register' discards 'const' qualifier from pointer target type
phy_dev_entry, &tzone_ops, &pkg_temp_tz_params, 0, 0);
^
In file included from drivers/thermal/x86_pkg_temp_thermal.c:30:0:
include/linux/thermal.h:378:29: note: expected 'struct thermal_zone_params *' but argument is of type 'const struct thermal_zone_params *'
struct thermal_zone_device *thermal_zone_device_register(const char *, int, int,
^
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Introduce an optional property called, sustainable-power, which
represents the power (in mW) which the thermal zone can safely
dissipate.
If provided the property is parsed and associated with the thermal
zone via the thermal zone parameters.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add trace events for the power allocator governor and the power actor
interface of the cpu cooling device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The power allocator governor is a thermal governor that controls system
and device power allocation to control temperature. Conceptually, the
implementation divides the sustainable power of a thermal zone among
all the heat sources in that zone.
This governor relies on "power actors", entities that represent heat
sources. They can report current and maximum power consumption and
can set a given maximum power consumption, usually via a cooling
device.
The governor uses a Proportional Integral Derivative (PID) controller
driven by the temperature of the thermal zone. The output of the
controller is a power budget that is then allocated to each power
actor that can have bearing on the temperature we are trying to
control. It decides how much power to give each cooling device based
on the performance they are requesting. The PID controller ensures
that the total power budget does not exceed the control temperature.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a basic power model to the cpu cooling device to implement the
power cooling device API. The power model uses the current frequency,
current load and OPPs for the power calculations. The cpus must have
registered their OPPs using the OPP library.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add three optional callbacks to the cooling device interface to allow
them to express power. In addition to the callbacks, add helpers to
identify cooling devices that implement the power cooling device API.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
A governor may need to store its current state between calls to
throttle(). That state depends on the thermal zone, so store it as
private data in struct thermal_zone_device.
The governors may have two new ops: bind_to_tz() and unbind_from_tz().
When provided, these functions let governors do some initialization
and teardown when they are bound/unbound to a tz and possibly store that
information in the governor_data field of the struct
thermal_zone_device.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for the temperature alarm peripheral found inside
Qualcomm plug-and-play (QPNP) PMIC chips. The temperature alarm
peripheral outputs a pulse on an interrupt line whenever the
thermal over temperature stage value changes.
Register a thermal sensor. The temperature reported by this thermal
sensor device should reflect the actual PMIC die temperature if an
ADC is present on the given PMIC. If no ADC is present, then the
reported temperature should be estimated from the over temperature
stage value.
Cc: David Collins <collinsd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor has the concept of weights, which is the
influence of each cooling device in a thermal zone. The current
implementation forces the weights of all cooling devices in a thermal
zone to add up to a 100. This complicates setups, as you need to know
in advance how many cooling devices you are going to have. If you bind a
new cooling device, you have to modify all the other cooling devices
weights, which is error prone. Furthermore, you can't specify a
"default" weight for platforms since that default value depends on the
number of cooling devices in the platform.
This patch generalizes the concept of weight by allowing any number to
be a "weight". Weights are now relative to each other. Platforms that
don't specify weights get the same default value for all their cooling
devices, so all their cdevs are considered to be equally influential.
It's important to note that previous users of the weights don't need to
alter the code: percentages continue to work as they used to. This
patch just removes the constraint of all the weights in a thermal zone
having to add up to a 100. If they do, you get the same behavior as
before. If they don't, fair share now works for that platform.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It's useful to have access to the weights for the cooling devices for
thermal zones and change them if needed. Export them to sysfs.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fair share governor is not usable with thermal zones that use the
bind op and don't populate thermal_zone_parameters, the majority of
them. Now that the weight is in the thermal instance, we can use that
in the fair share governor to allow every thermal zone to trivially use
this governor. Furthermore, this simplifies the code.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently you can specify the weight of the cooling device in the device
tree but that information is not populated to the
thermal_bind_params where the fair share governor expects it to
be. The of thermal zone device doesn't have a thermal_bind_params
structure and arguably it's better to pass the weight inside the
thermal_instance as it is specific to the bind of a cooling device to a
thermal zone parameter.
Core thermal code is fixed to populate the weight in the instance from
the thermal_bind_params, so platform code that was passing the weight
inside the thermal_bind_params continue to work seamlessly.
While we are at it, create a default value for the weight parameter for
those thermal zones that currently don't define it and remove the
hardcoded default in of-thermal.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables intel_powerclamp driver to run on the
next-generation Intel(R) Xeon Phi Microarchitecture
code named "Knights Landing"
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
drivers/thermal/intel_soc_dts_iosf.c:358:4-7: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In Intel Quark SoC X1000, there is one on-die digital temperature sensor(DTS).
The DTS offers both hot & critical trip points.
However, in current distribution of UEFI BIOS for Quark platform, only
critical trip point is configured to be 105 degree Celsius (based on Quark
SW ver1.0.1 and hot trip point is not used due to lack of IRQ.
There is no active cooling device for Quark SoC, so Quark SoC thermal
management logic expects Linux distro to orderly power-off when temperature
of the DTS exceeds the configured critical trip point.
Kernel param "polling_delay" in milliseconds is used to control the frequency
the DTS temperature is read by thermal framework. It defaults to 2-second.
To change it, use kernel boot param "intel_quark_dts_thermal.polling_delay=X".
User interacts with Quark SoC DTS thermal driver through sysfs via:
/sys/class/thermal/thermal_zone0/
For example:
- to read DTS temperature
$ cat temp
- to read critical trip point
$ cat trip_point_0_temp
- to read trip point type
$ cat trip_point_0_type
- to emulate temperature raise to test orderly shutdown by Linux distro
$ echo 105 > emul_temp
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support two auxiliary DTS present on Braswell platform using side band
IOSF interface. This supports two read write trips, which can be used
to get notification on trip violation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
There is no change in functionality but using the common IOSF core APIs.
This driver is now just responsible for enumeration and call relevant
API to create thermal zone and register critical trip.
Also cpuid 0x4c is now handled in the int340x processor thermal driver
with the same functionality.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This is becoming a common feature for Intel SoCs to expose the additional
digital temperature sensors (DTSs) using side band interface (IOSF). This
change remove common IOSF DTS handler function from the existing driver
intel_soc_dts_thermal.c and creates a stand alone module, which can
be selected from the SoC specific drivers. In this way there is less
code duplication.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Default attributes are created when the device is registered. Attributes
created after device registration can lead to race conditions, where user space
(e.g. udev) sees the device but not the attributes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When thermal zone device register fails or on module exit, the memory
for aux_trip is not freed. This change fixes this issue.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the wrong control of PD_DET_EN (power down detection mode)
for Exynos7 because exynos7_tmu_control() always enables the power down detection
mode regardless 'on' parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It is possible that _ART/_TRT tables are missing or have errors.
Ignore those failures, as INT3400 thermal zone is still required
for _OSC or mode switch.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Atom* Processor C2000 Product
Family for Microservers (Avoton). Avoton - SoCs for micro-servers
has package C-states which can be used for idle injection.
Reported-by: Jose Navarro <jose.navarro@intel.com>
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jos.c.venegas.munoz@intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Swap interrupt disable and thermal zone unregistration in the error and
remove paths, to make them more symmetrical with the initialization
path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As soon as the interrupt has been enabled by devm_request_irq(), the
interrupt routine may be called, depending on the current status of the
hardware.
However, at that point rcar_thermal_common hasn't been initialized
complely yet. E.g. rcar_thermal_common.base is still NULL, causing a
NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0004000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30
Hardware name: Generic R8A73A4 (Flattened Device Tree)
task: ee8953c0 ti: ee896000 task.ti: ee896000
PC is at rcar_thermal_irq+0x1c/0xf0
LR is at _raw_spin_lock_irqsave+0x48/0x54
Postpone the call to devm_request_irq() until all initialization has
been done to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix following build warning if CONFIG_PM_SLEEP is not set:
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1478:12: warning: 'ti_bandgap_suspend' defined but not used [-Wunused-function]
static int ti_bandgap_suspend(struct device *dev)
^
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1492:12: warning: 'ti_bandgap_resume' defined but not used [-Wunused-function]
static int ti_bandgap_resume(struct device *dev)
^
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
Pull thermal managament updates from Zhang Rui:
"Specifics:
- Abstract the code and introduce helper functions for all int340x
thermal drivers. From: Srinivas Pandruvada.
- Reorganize the ACPI LPAT table support code so that it can be
shared for both ACPI PMIC driver and int340x thermal driver.
- Add support for Braswell in intel_soc_dts thermal driver.
- a couple of small fixes/cleanups for step_wise governor and int340x
thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal/int340x_thermal: remove unused uuids.
thermal: step_wise: spelling fixes
thermal: int340x: fix sparse warning
Thermal/int340x: LPAT conversion for temperature
ACPI / PMIC: Use common LPAT table handling functions
ACPI / LPAT: Common table processing functions
thermal: Intel SoC DTS: Add Braswell support
Thermal/int340x/int3402: Provide notification support
Thermal/int340x/processor_thermal: Add thermal zone support
Thermal/int340x/int3403: Use int340x thermal API
Thermal/int340x/int3402: Use int340x thermal API
Thermal/int340x: Add common thermal zone handler
this patch fixes following sparse warning:
processor_thermal_device.c:188:6: warning: symbol 'proc_thermal_remove' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add registers, bit fields and compatible strings for Exynos7 TMU
(Thermal Management Unit). Following are a few of the differences
in the Exynos7 TMU from earlier SoCs:
- 8 trigger levels
- Different bit offsets and more registers for the rising
and falling thresholds.
- New power down detection bit in the TMU_CONTROL register
which does not update the CURRENT_TEMP0 when tmu power down
is detected.
- Change in bit offset for the NEXT_DATA field of EMUL_CON
register. EMUL_CON register address has also changed.
- INTSTAT and INTCLEAR registers present in earlier SoCs
have been combined into one INTPEND register. The register
address for INTCLEAR and INTPEND is also different.
- Since there are 8 rising/falling interrupts as against
at most 4 in earlier SoCs the INTEN bit offsets are different.
- Multiple probe support which is handled by a TMU_CONTROL1
register (No support for this in the current patch).
This patch adds special clock support required only for Exynos7. It
also updates the "code_to_temp" prototype as Exynos7 has 9 bit
code-temp mapping.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When LPAT table is present, we need to convert raw temperature to
real temp using LPAT.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added Intel Braswell CPU id for SOC DTS. Since this doesn't support
APIC IRQ, the driver is modified to have capability to not register
any modifiable trips.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Up till now, by mistake, wrong variable was tested against being NULL.
Since exynos_report_trigger() is always called with valid p pointer,
it is only necessary to check if a valid thermal zone device is passed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing exynos_thermal_common.[c|h] files the CONFIG_EXYNOS_THERMA_CORE
is not needed anymore.
This patch removes this entry from Kconfig.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Data already present in the exynos_tmu_data.c file has been moved to the
appropriate device tree files.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In general, the kernel should report temperature readings exactly as
reported by the hardware. The cpu / gpu thermal driver works in 5 degree
increments,but we ought to do more accurate. The temperature will do
linear interpolation between the entries in the table.
Test= $md5sum /dev/zero &
$while true; do grep "" /sys/class/thermal/thermal_zone[1-2]/temp;
sleep .5; done
e.g. We can get the result as follows:
/sys/class/thermal/thermal_zone1/temp:39994
/sys/class/thermal/thermal_zone2/temp:39086
/sys/class/thermal/thermal_zone1/temp:39994
/sys/class/thermal/thermal_zone2/temp:39540
/sys/class/thermal/thermal_zone1/temp:39540
/sys/class/thermal/thermal_zone2/temp:39540
/sys/class/thermal/thermal_zone1/temp:39540
/sys/class/thermal/thermal_zone2/temp:39994
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After defining all necessary Exynos data in the device tree and heavy
reusage of the of-thermal.c those files can be removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch brings support for providing configuration via device tree.
Previously this data has been hardcoded in the exynos_tmu_data.c file.
Such approach was not scalable and very often required copying the whole
data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Up till now exynos_tmu_data.c was used for storing CPU cooling configuration
data. Now the Exynos thermal core code uses device tree to get this data.
For this purpose generic thermal code for configuring CPU cooling was
used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch is a preparatory patch to be able to read Exynos thermal
configuration from the device tree.
It turned out that DTC is not able to interpret enums properly and hence
it is necessary to #define those values explicitly.
For this reason the ./include/dt-bindings/thermal/thermal_exynos.h file
has been introduced.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Up till now the thermal_zone mode was by default "disabled". With this
patch the default behavior was changed to "enable".
One can read the mode at:
/sys/class/thermal/thermal_zone0/mode
Tested-by: Javi Merino <javi.merino@arm.com>
Reported-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Added thermal zones for processor thermal using APIs provided by
int340x thermal zone module.
Like other INT340x devices, processor thermal device can also contain
trip points and way to get temperature. On some platform there is
no ACPI _TMP method, in those platform using IA64 architecture MSRs to
get temperature.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Using APIs from int340x thermal zone module to add and remove thermal
zones.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Using APIs from int340x thermal zone module to add and remove thermal
zones.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Most of the processing for each int340x driver to add a thermal zone
is very similar and every driver has to duplicate code.
Created a common module, which exports API to add and remove zones.
In this way, we not only avoid duplicate code but also helps in
bug fixes and enhancements.
If for some driver default processing for thermal zone callback is
not enough they can overide individual callback.
The code for this driver is primarily copied from int3402_thermal.c.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal fixes from Zhang Rui:
"Specifics:
- bogus type qualifier fix in OF thermal code.
- Minor fixes on imx and rcar thermal drivers.
- Update TI SoC thermal maintainer entry.
- Updated documentation of OF cpufreq cooling register"
* 'thermal-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar: Spelling/grammar: s/drier use .../driver uses ...s/
thermal: rcar: change type of ctemp in rcar_thermal_update_temp()
thermal: rcar: fix ENR register value
Documentation: thermal: document of_cpufreq_cooling_register()
Thermal: imx: add clk disable/enable for suspend/resume
MAINTAINERS: update ti-soc-thermal status
MAINTAINERS: Add linux-omap to list of reviewers for TI Thermal
thermal: of: Remove bogus type qualifier for of_thermal_get_trip_points()
Since the ctemp is used for rcar_thermal_write() in
rcar_thermal_update_temp(), the type of 'ctemp' should be "u32" instead
of "int". This patch also changes type of the helper variables 'old'
and 'new'.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On R-Mobile APE6, since it has 3 thermal zones, ENR register
has enable bits in bit 19-16, bit 11-8 and bit 3-0.
However, on R-Car gen2, since it has 1 thermal zone, ENR register has
enable bits in bit 3-0. (In other words, the write value should always
be 0 for bit 31-4 of ENR register.)
So, this patch fixes the ENR register value using I/O resource sets.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal sensor's clk is from pll3_usb_otg, per hardware
design requirement, need to make sure pll3_usb_otg is disabled
before STOP mode is entered, otherwise, all PFDs under it may
enter incorrect state, this patch disables pll3_usb_otg before
suspend and enables it after resume.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
there is no ACPI device object
processor_thermal_device driver needs ACPI support to work. Thus, the driver
probing should fail when there is no ACPI device object asscociated.
This fixes a NULL pointer dereference when the driver is loaded
with INT340X feature disabled in BIOS.
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
For some INT340X thermal devices, even if they are not referred in
_TRT/_ART table, they still can be used by userspace for thermal control.
Thus change the code to enumerated all the INT340X devices,
no matter if they're referred in _TRT/_ART or not.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
With gcc 4.1.2, 4.2, and 4.2.4 (4.4 and later are OK):
drivers/thermal/thermal_core.h:110: warning: type qualifiers ignored on function return type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: ce8be77859 ("thermal: of: Extend of-thermal to export table of trip points")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Int340x thermal provides a processor thermal device, which
is used to control processor thermal states. These devices are
either reported as a PCI device or an ACPI device. This
device provides power limits, control states and optional
temperature.
This change implements minimal requirements to expose processor
power limits which can be used during thermal power limiting.
Power limits are exposed via an attribute group called
"power_limits" under the device. The exported attributes
are:
power_limit_0_max_uw
power_limit_1_max_uw
power_limit_0_min_uw
power_limit_1_min_uw
power_limit_0_tmin_us
power_limit_1_tmin_us
power_limit_0_tmax_us
power_limit_1_tmax_us
power_limit_0_step_uw
power_limit_1_step_uw
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The node field of struct cpufreq_cooling_device was reintroduced in
2dcd851fe4 (thermal: cpu_cooling: Update always cpufreq policy with
thermal constraints) but without the documentation that it once had.
Add it back so that all the fields of struct cpufreq_cooling_device
are documented.
Cc: Yadwinder Singh Brar <yadi.brar@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable Intel Powerclamp driver on Xeon cpu id 0x56, package C-state
is available on this CPU for idle injection.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If either of the entries was missing, the driver tried to free memory
using uninitialized pointer. In addition, it was dereferencing null
pointer.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
commit 4dbd27711c "tick: export nohz tick idle symbols for module
use" was merged via the thermal tree without an explicit ack from the
relevant maintainers.
The exports are abused by the intel powerclamp driver which implements
a fake idle state from a sched FIFO task. This causes all kinds of
wreckage in the NOHZ core code which rightfully assumes that
tick_nohz_idle_enter/exit() are only called from the idle task itself.
Recent changes in the NOHZ core lead to a failure of the powerclamp
driver and now people try to hack completely broken and backwards
workarounds into the NOHZ core code. This is completely unacceptable
and just papers over the real problem. There are way more subtle
issues lurking around the corner.
The real solution is to fix the powerclamp driver by rewriting it with
a sane concept, but that's beyond the scope of this.
So the only solution for now is to remove the calls into the core NOHZ
code from the powerclamp trainwreck along with the exports.
Fixes: d6d71ee4a1 "PM: Introduce Intel PowerClamp Driver"
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Pan Jacob jun <jacob.jun.pan@intel.com>
Cc: LKP <lkp@01.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1412181110110.17382@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
There was a left over return here so the error handling isn't run.
It leads to a small memory leak and a static checker warning.
drivers/thermal/cpu_cooling.c:351 __cpufreq_cooling_register()
info: ignoring unreachable code.
Fixes: f6859014c7 ("thermal: cpu_cooling: Store frequencies in descending order")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Avoid printing the error message in the EPROBE_DEFER case
where registering cpu cooling at ti-soc-thermal thermal driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Avoid printing the error message in the EPROBE_DEFER case
where registering cpu cooling at db8500 thermal driver.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During imx_thermal probe we have the following log:
[ 1.514819] imx_thermal 2000000.aips-bus:tempmon: failed to register cpufreq cooling device: -517
[ 1.515064] platform 2000000.aips-bus:tempmon: Driver imx_thermal requests probe deferral
Avoid printing the error message in the EPROBE_DEFER case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As samsung thermal support is enabled only for ARCH_EXYNOS, there is no
need to select ARCH_HAS_BANDGAP from the arch-specific code. Removing this
dependency will also allow the driver to be enabled on 64-bit SoCs.
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Previously the return value of the last acpi_bus_get_device() was
returned. However, since we only report those issues, it should be
cleared to continue as expected.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Braswell also has package C-states which can be used for idle
injection. This patch adds Braswell CPU ID in intel powerclamp
driver.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
drivers/thermal/int340x_thermal/int3403_thermal.c:468:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Avoid pointer casting which may also lead to problems on big endian
64 bit systems.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal_zone_device_unregister() function tests whether its argument
is NULL and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
INT3400 currently supports only one policy, which can't be changed.
This change exports all available policies (uuids) to user space and
allow this to be changed.
It introduces an attribute group uuids in INT3400 platform driver.
There are two attributes exposed:
- available_uuids
- current_uuid
User space can set current_uuid via this interface to one of the
available uuids. The uuid change is communicated to firmware, only
when the current zone mode is changed to "enabled". So the ideal
sequence should be
- set INT3400 zone mode to "disabled"
- change current_uuid
- set INT3400 zone mode to "enabled"
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The return code from ->get_max_state() callback was not checked during
binding cooling device to thermal zone device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Before this change it was only possible to set get_temp() and get_trend()
methods to be used in the common code handling passing parameters via
device tree to "cpu-thermal" CPU thermal zone device.
Now it is possible to also set emulated value of temperature for debug
purposes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to export trip points for a given
thermal zone.
Thermal drivers should use of_thermal_get_trip_points() method to get
pointer to table of thermal trip points.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch changes name of struct __thermal_trip to thermal_trip and moves
declaration of the latter to ./include/linux/thermal.h for better visibility.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to provide check if trip point is
valid.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch extends the of-thermal.c to provide information about number of
available trip points.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Adding my copyright information for two purposes:
- To get cc'd for future patches to review (Only if people read this header
while sending mail)
- Have done enough changes to earn a place here?
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
get_property() was an over complicated beast with BUGs. It used to believe that
cpufreq table is present in ascending or descending order, which might not
always be true.
Previous patch has created another freq table in descending order for us and we
better use it now. With that get_property() simply goes away and another helper
get_level() comes in.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
CPUFreq framework *doesn't* guarantee that frequencies present in cpufreq table
will be in ascending or descending order. But cpu_cooling somehow assumes that.
Probably because most of current users are creating this list from DT, which is
done with the help of OPP layer. And OPP layer creates the list in ascending
order of frequencies.
But cpu_cooling can be used for other platforms too, which don't have
frequencies arranged in any order.
This patch tries to fix this issue by creating another list of valid frequencies
in descending order. Care is also taken to throw warnings for duplicate entries.
Later patches would use it to simplify code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We already know the value of 'cpufreq_dev->max_level' and so there is no need
calculating that once again. For this, we need to send 'cpufreq_dev' to
get_property().
Make all necessary changes for this change. Because cpufreq_cooling_get_level()
doesn't have access to 'cpufreq_dev', it is updated to iterate over the list of
cpufreq_cooling_devices to get cooling device for the cpu number passed to it.
This also makes it robust to return levels only for the CPU registered via a
cooling device. We don't have to support anything that isn't registered yet.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As we already have a list of cpufreq_cooling_devices now, lets use it instead of
a local counter.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We don't use get_property() to find max levels anymore as it is done at boot
now. So, don't support GET_MAXL in get_property().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
CPU frequency tables don't update after the driver is registered and so we don't
need to iterate over them to find total number of states every time
cpufreq_get_max_state() is called. Do it once at boot time.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
get_cpu_frequency() isn't doing much by itself, just calling get_property(). And
so this wrapper isn't required at all. Get rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cpufreq_apply_cooling() has a single caller, cpufreq_set_cur_state() and
cpufreq_set_cur_state() is an unnecessary wrapper over cpufreq_apply_cooling().
Get rid of it by merging both routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point checking for validity of 'cpufreq_val' from
cpufreq_thermal_notifier() every time the routine is called. Its guaranteed to
be 0 on the first call but will be valid otherwise.
Lets update it once while the device registers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This makes life easy and bug free. And is scalable for future resource
allocations.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Because get_cpu_frequency() has returned a valid frequency, it means that the
cpufreq policy is surely valid and so no point checking that again with
is_cpufreq_valid(). Get rid of the routine as well as there are no more users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All CPUs present in 'allowed_cpus' share the same 'struct cpufreq_policy'
structure and so calling cpufreq_update_policy() for each of them doesn't make
sense.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In __cpufreq_cooling_register() we try to match min/max frequencies for all CPUs
passed in 'clip_cpus' mask. This mask is the cpumask of cpus where the frequency
constraints will be applied.
Same frequency constraint can be applied only to the CPUs belonging to the same
cluster (i.e. CPUs sharing clock line). For all such CPUs we have a single
'struct cpufreq_policy' structure managing them and so getting policies for all
CPUs wouldn't make any sense as they will all return the same pointer.
So, remove this useless check of checking min/max for all CPUs. Also update doc
comment to make this more obvious that clip_cpus should be same as
policy->related_cpus.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We aren't supposed to return our own error type here. Return what we got.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
ret is initialized before it is used, so no need to set it to 0 in its declaration.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
It will be overwritten soon with return value of kzalloc().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This wasn't explained well anywhere and should be clearly specified. Lets add a
top level comment for this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
cooling_cpufreq_lock isn't used to protect this structure and so the comment
over it is outdated. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
