__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is not used outside of l2cap_core.c. Also l2cap_ertm_data_rcv is
only used after it is defined so there is no need for forward declaration.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These flags can and will be used for more general purpose values than
just pending state transitions so the more common name "flags" makes
more sense than "pend".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Remove unneeded conversion from sk to chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reference counter was incremented when starting ack timer but
decremented only when clearing timer, not when timer fired.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to send RNR immediately when entring local busy.
Also upper layer might clear local busy condition before ack timer
expires saving few cycles for sending RNR.
This also prevents sending two RNRs in some cases where sending one
would be enough i.e received N I-frame can trigger local busy
(sending RNR acking up to N-1 I-frame) and later sending ack (RNR
acking up to N I-frame).
This was affecting TC_ERM_BV_07_C and TC_ERM_BV_22_C with some non
default channel parameters (tx window and receiving buffer sizes).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ack_timer should be cleared when sending ACK to avoid acking I-frames
twice.
This commit introduces helper function (only send ack, not clearing
timer) which is used by l2cap_send_ack and l2cap_ack_timeout. This is
to avoid clearing ack timer in timer function.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
SREJ frame with P-bit set acknowledges I-frames numbered up to
(ReqSeq - 1). With this patch P-bit in SREJ is set only when there are
some I-frames to ack.
This fixes ambiguous situation when lost of I-frame with TxSeq=0 would
result in sending SREJ acking all previous I-frames.
Consider following scenario:
TxWindow=3
HostA: sent I-frame TxSeq=0
HostA: sent I-frame TxSeq=1
HostA: sent I-frame TxSeq=2
HostB: missed I-frame TxSeq=0
HostB: received I-frame TxSeq=1
HostB: sent SREJ ReqSeq=0 Pbit=1
HostA: received SREJ ReqSeq=0 Pbit=1 <- All I-frames acked or not?
...
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Those locks are not shared between interrupt and process context anymore,
so remove the part that disable interrupts. We are still safe because
preemption is disabled.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It should be the dst in the copy not src. 03a001948 introduced this bug.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It makes more sense this way, since info_timer is a timer using delayed
work API.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This one also needs to run in process context
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring an ERTM or streaming mode connection, remote devices
are expected to send an RFC option in a successful config response. A
misbehaving remote device might not send an RFC option, and the L2CAP
code should not access uninitialized data in this case.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This list has much more reads than writes, so RCU makes senses here, also
it avoid deadlock against the socket lock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
spin lock doesn't fit ok anymore on the new code based on workqueues.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We run everything in the same lock now. The backlog queue is useless now
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We now run everything in process context, so the mutex lock is the best
option. But in some places we still need the bh_lock_sock()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP timers also need to run in process context. As the works in l2cap
are small we are using the system worqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now we run everything in HCI in process context, so it's a better idea use
mutex instead spin_lock. The macro remains hci_dev_lock() (and I got rid
of hci_dev_lock_bh()), of course.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
I did this as a part of a testing course at university, but it might be
useful upstream as well.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fixes bluetooth compiling when CONFIG_BT_L2CAP is not enabled
net/built-in.o: In function `hci_dev_open':
(.text+0xdce9a): undefined reference to `enable_hs'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make __l2cap_global_chan_by_addr similar to other find functions.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This make it easier to see what is the real reason for loop to exit.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make it easier to see what is loop break condition.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Due to ERTM reliability L2CAP channel needs to be disconnected if
adding to srej list failed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
rename to l2cap_chan_check_security() to make it consistent with other
l2cap_exported functions. This function will be exported in a later
commit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
AMP channels can be moved between BR/EDR and AMP controllers using a
sequence of signals. Every attempted channel move involves a series of
four signals:
Move Initiator Move Responder
| |
| Move Channel Request |
| ----------------------------> |
| |
| Move Channel Response |
| <---------------------------- |
| |
| Move Channel Confirm |
| ----------------------------> |
| |
| Move Channel Confirm Response |
| <---------------------------- |
All four signals are sent even if the move fails.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
