The wm8940 provides the chip ID information via I2C. In this
patch this information is read and if not matching expected
value, the probe function is aborted.
This prevents from using (i.e. inserting) other wm89* modules
which use the same I2C bus address.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221216094624.3849278-3-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables support for internal wm8940's PLL and proper
divider to set proper value for 256x fs clock.
This approach is more flexible and replaces hardcoded clock
values and makes the codec work with the simple-card driver.
Card drivers calling set_pll() and set_clkdiv() directly are
unaffected.
For the reference - code in this commit is based on:
51b2bb3f25
("ASoC: wm8974: configure pll and mclk divider automatically")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221216094624.3849278-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The lack of platform data in the contemporary Linux
shall not be the reason to display warnings to the
kernel logs.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221216094624.3849278-1-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the DAI mono mode support and set the frame width to 32
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Tested-by: David Rau <David.Rau.opensource@dm.renesas.com>
Signed-off-by: David Rau <David.Rau.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20221214044058.6289-1-David.Rau.opensource@dm.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP SRAM is not used for audio shared buffer between host and DSP so
TOTAL_SIZE_SHARED_SRAM_FROM_TAIL is zero. Remove the definition and
redundant comparison to fix coverity "unsigned compared against 0".
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angeloigoacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221215061046.16934-1-yc.hung@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The error "Conflict in bytes vs. priv size." is too brief. With
the printed sizes it's a lot easier to find the size issue in
for binary control if such happens.
Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221216115350.28260-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_debug value is set by the user, developer intentionally.
To save time on figuring out what value has been passed to the kernel by
the user, developer, print it out if it is not 0.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20221216115435.28427-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for suspend to RAM by re-aranging the lines in switch..case
from mchp_pdmc_trigger() and saving/restoring the enabled interrupts. These
are necessary as AT91 devices has a special power saving mode (called
backup and self-refresh) where most of the SoC parts are powered off
and thus we need to reconfigure the PDMC on resume.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221213112851.89212-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement clock power saving taking advantage of runtime PM infrastructure.
This simplifies the code and allow using the same infrastructure for
suspend to RAM functionalities.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221213112851.89212-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle creation of peakvol module in FW. When peakvol module is created
it retrieves actual value from kcontrol and sends it to FW as part of
configuration data.
Co-authored-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20221214185500.3896902-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add callback to handle loading of kcontrol and linking it to active
widget. In order to link kcontrol to specific modules add additional
field to module data, as well as specify control id in kcontrol data.
Co-authored-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20221214185500.3896902-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To make introduced peakvol module useful from userspace perspective,
expose ALSA controls allowing DSP volume modification. These provide
even more granular control over volume but are also the only way to
modify volume for devices devoid of codec kcontrols e.g.: DMIC.
Co-authored-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20221214185500.3896902-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peakvol module allows for setting and obtaining DSP volume as well as
modifying shape and duration at which volume actually changes. Add IPC
messages to expose those capabilities.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20221214185500.3896902-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221212205406.3771071-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221212205406.3771071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221212205406.3771071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the sdev->fw_trace_is_supported is true then we must have the fw_tracing
ops set, no need to check again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For the sake of safety use the sof_ipc_get_ops() to fetch the fw_tracing
ops to avoid cases when either sdev->ipc or sdev->ipc->ops might be NULL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code treats the fw_tracing as optional feature but the documentation
was not reflecting this.
Correct it by explicitly stating that the fw_tracing is optional.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC ops are optional, but they require that the ops struct is to be
allocated with all callbacks set to NULL.
Update the code to extend the optionality to:
sdev->ipc == NULL
sdev->ipc->ops == NULL
sdev->ipc->ops->[pm/tplg] == NULL (treated optional for pm currently)
sdev->ipc->ops->[pm/tplg]->ops == NULL (treated optional currently)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC ops are optional, but they require that the ops struct is to be
allocated with all callbacks set to NULL.
Update the code to extend the optionality to:
sdev->ipc == NULL
sdev->ipc->ops == NULL
sdev->ipc->ops->[tplg] == NULL
sdev->ipc->ops->[tplg]->ops == NULL (treated optional currently)
At the same time standardize the naming of the ops pointer to tplg_ops
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC ops are optional, but they require that the ops struct is to be
allocated with all callbacks set to NULL.
Update the code to extend the optionality to:
sdev->ipc == NULL
sdev->ipc->ops == NULL
sdev->ipc->ops->[ops_group] == NULL
sdev->ipc->ops->[pcmops_group]->ops == NULL (treated optional currently)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC ops are optional, but they require that the ops struct is to be
allocated with all callbacks set to NULL.
Update the code to extend the optionality to:
sdev->ipc == NULL
sdev->ipc->ops == NULL
sdev->ipc->ops->[tplg] == NULL
sdev->ipc->ops->[tplg]->control == NULL
sdev->ipc->ops->[tplg]->control->ops == NULL (treated optional currently)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC ops are optional, but they require that the ops struct is to be
allocated with all callbacks set to NULL.
Update the code to extend the optionality to:
sdev->ipc == NULL
sdev->ipc->ops == NULL
sdev->ipc->ops->[pcm] == NULL
sdev->ipc->ops->[pcm]->ops == NULL (treated optional currently)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to a case when the DSP is not used.
In this case the IPC communication itself has no meaning and we might
not even have sdev->ipc allocated at all.
The sof_ipc_get_ops() macro can be used to get a named IPC ops struct or
return NULL if the sdev->ipc is not allocated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The core treats all function pointer in sof_ipc_tplg_ops as optional.
Update the documentation to reflect this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Other topology ops have been treated as optional, including the route_free.
Handle the route_setup in a conforming way as optional callback.
Note: we do not have checks for the callbacks itself which makes them all
optional in practice.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20221221102328.9635-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
allocator, as it copes with that just as badly as the coherent allocator,
and then add a check to make sure no one passes the flag ever again.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAmOlvh8LHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYN/Ig//SHLj6xlAPHiBSMY44j0qQj4w63G4WivPs4B0Nr7j
Wne6yh0x8pg2L/BDY1KWoMqo8XhNIXVYKx6jahdqrik9IKJinIZPKT9nYkK5TbO+
RQSu4HKqAsrMO7u1+LzVyhNZqOtavRXj4EJkkienHDTh7Rqry5o8hBAe40G2BLqe
TMrnPLAJ0VZ/I45LakzCSCR2WC8GA+33849zJO1Vd4glnxL+VdM5WigYi1N2j6Ng
d4ymVbprnJljXjIDK2aMy1AGw5ctlQE1hslD2OoUr/onJ6PPU1rmYmf/B1fm8Cqh
ahxv2jJJsZ0BvwO7uouU6rsJfVGaZx7dMkABmX+A9b7RtP9mC19qc76VleYUouKB
v28SJD+jFUoQIO5ylly2LEvSgiEPspymv1VJtYdX/y6/YAtm2XFgmIEJdv6dGQu0
ZMpAs2nCfxzsGy4mQNpXEnBZwrP7GnEtm1ynBLQ1/SJ7toqBmX9/4JzZuRZ0TPEh
gw+Tkl3fC/jfLUDaLSjCnJw4OpH4+ai9tJuhXtPZk6UN5VPrQbz5xu9bh6wiyPqX
Pm6ubCDv0Y3I1rwoXwVIcrWfOMTAm8OwfMHCBRoRVp1vfuFSihptpWjIIx6rQCrI
sdZtVla+FblL9zO5WvGStlx9FiZa39HJm2d6rQIazI5of6iNf9/xSyoWNcNWSrcu
EFY=
=q0m6
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
allocator, as it copes with that just as badly as the coherent
allocator, and then add a check to make sure no one passes the flag
ever again"
* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject GFP_COMP for noncoherent allocations
ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations
A few more updates for 6.2 since the last PR: most of changes are
about ASoC device-specific fixes.
- Lots of ASoC Intel AVS extensions and refactoring
- Quirks for ASoC Intel SOF as well as regression fixes
- ASoC Mediatek and Rockchip fixes
- Intel HD-audio HDMI workarounds
- Usual HD- and USB-audio device-specific quirks
-----BEGIN PGP SIGNATURE-----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=2Uko
-----END PGP SIGNATURE-----
Merge tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"A few more updates for 6.2: most of changes are about ASoC
device-specific fixes.
- Lots of ASoC Intel AVS extensions and refactoring
- Quirks for ASoC Intel SOF as well as regression fixes
- ASoC Mediatek and Rockchip fixes
- Intel HD-audio HDMI workarounds
- Usual HD- and USB-audio device-specific quirks"
* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
ASoC: lochnagar: Fix unused lochnagar_of_match warning
ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
ASoC: SOF: mediatek: initialize panic_info to zero
ASoC: rt5670: Remove unbalanced pm_runtime_put()
ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
ASoC: wm8994: Fix potential deadlock
ASoC: mediatek: mt8195: add sof be ops to check audio active
ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
ALSA: hda/hdmi: fix i915 silent stream programming flow
ALSA: hda: Error out if invalid stream is being setup
ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
ASoC: codecs: wcd-clsh: Remove the unused function
...
Some more small fixes and board quirks that came in since my last
update, the main one being the fixes from Kai for issues around the
attempts to get kexec working well on SOF based systems.
-----BEGIN PGP SIGNATURE-----
iQEyBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOhn2kACgkQJNaLcl1U
h9Dfdgf47os8jUAaEuV3/pFl7OOh+L2jR2P5yCK60VHu0CfuHo3lynwpYvS/8wKN
XqYz0eeuYOWpFeZ12wZBY/Dnk2dwkXiqpv7e0ID0szAH9TezSlQ3MRno9hwWGloU
w3ntU5VeIYTKl91E2y5X9GMoDsfnfh751MsjXOcP40npjGEJpOtAO0z1sIXANSKz
ftceXGapvTokSp7mbk68BM5ivom4TM3eDSlQiOeMj2OeOhXRylx5tHeQV3FzVeB+
4K7bECzveDn/hTYBX2Lopn2stR1RF5S9HDynjo83YDKXOKUp8bJfEHK7R/3y3u56
eIwKgMmxb2eK2IwgjU/7sKP87ARz
=OaSY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.2-3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.2
Some more small fixes and board quirks that came in since my last
update, the main one being the fixes from Kai for issues around the
attempts to get kexec working well on SOF based systems.
It seems that the firmware is broken and does not accept
the UAC_EP_CS_ATTR_SAMPLE_RATE URB. There is only one rate (48000Hz)
available in the descriptors for the output endpoint.
Create a new quirk QUIRK_FLAG_FIXED_RATE to skip the rate setup
when only one rate is available (fixed).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216798
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20221215153037.1163786-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow system health detection mechanisms to check the FW state, this
will allow them to check if the FW is in its "crashed" state going
forward to help automatically diagnose driver state.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221220125629.8469-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the DSP is suspended while the firmware is in the crashed state, we
skip tearing down the pipelines. This means that the widget reference
counts will not get to reset to 0 before suspend. This will lead to
errors with resuming audio after system resume. To fix this, invoke the
tear_down_all_pipelines op before skipping to DSP suspend.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221220125629.8469-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP crashes before the system suspends, the setting of target state
will be skipped because the firmware state will no longer be
SOF_FW_BOOT_COMPLETE. This leads to the incorrect assumption that the
DSP should suspend to D0I3 instead of suspending to D3. To fix this,
set the target_state before we skip to DSP suspend even when the DSP has
crashed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221220125629.8469-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While not quite as bogus as for the dma-coherent allocations that were
fixed earlier, GFP_COMP for these allocations has no benefits for
the dma-direct case, and can't be supported at all by dma dma-iommu
backend which splits up allocations into smaller orders. Due to an
oversight in ffcb754584 that flag stopped being cleared for all
dma allocations, but only got rejected for coherent ones.
Start fixing this by not requesting __GFP_COMP in the sound code, which
is the only place that did this.
Fixes: ffcb754584 ("dma-mapping: reject __GFP_COMP in dma_alloc_attrs")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reported-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
- intel: reorganization of hw_ops callbacks, splitting files etc
- qcom: support for v1.7.0 qcom controllers
-----BEGIN PGP SIGNATURE-----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=3uDi
-----END PGP SIGNATURE-----
Merge tag 'soundwire-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
"This include bunch of Intel driver code reorganization and support for
qcom v1.7.0 controller:
- intel: reorganization of hw_ops callbacks, splitting files etc
- qcom: support for v1.7.0 qcom controllers"
* tag 'soundwire-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: intel: split auxdevice to different file
soundwire: intel: add in-band wake callbacks in hw_ops
soundwire: intel: add link power management callbacks in hw_ops
soundwire: intel: add bus management callbacks in hw_ops
soundwire: intel: add register_dai callback in hw_ops
soundwire: intel: add debugfs callbacks in hw_ops
soundwire: intel: start using hw_ops
dt-bindings: soundwire: Convert text bindings to DT Schema
soundwire: cadence: use dai_runtime_array instead of dma_data
soundwire: cadence: rename sdw_cdns_dai_dma_data as sdw_cdns_dai_runtime
soundwire: qcom: add support for v1.7 Soundwire Controller
dt-bindings: soundwire: qcom: add v1.7.0 support
soundwire: qcom: make reset optional for v1.6 controller
soundwire: qcom: remove unused SWRM_SPECIAL_CMD_ID
soundwire: dmi-quirks: add quirk variant for LAPBC710 NUC15
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
lochnagar_of_match is used unconditionally, so COMPILE_TEST builds
without OF warn:
sound/soc/codecs/lochnagar-sc.c:247:34: error: ‘lochnagar_of_match’ defined but not used [-Werror=unused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221215134337.77944-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The bytcr_rt5640.c file already supports the HP Stream 7.
The HP Stream 8 is almost identical in terms of the hardware
with the exception of it having stereo speakers, a SIM
card slot and the obvious size difference.
Signed-off-by: Moises Cardona <moisesmcardona@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221214120830.1572474-1-moisesmcardona@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue, including
support for loading libraries and probes with IPC4 on SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems, Mediatek
systems with multiple DMICs, Nuvoton NAU8318, NXP fsl_rpmsg and
i.MX93, Qualcomm AudioReach Enable, MFC and SAL, RealTek RT1318 and
Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
Also, this PR also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates
-----BEGIN PGP SIGNATURE-----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=QV3a
-----END PGP SIGNATURE-----
Merge tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue,
including support for loading libraries and probes with IPC4 on
SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems,
Mediatek systems with multiple DMICs, Nuvoton NAU8318, NXP
fsl_rpmsg and i.MX93, Qualcomm AudioReach Enable, MFC and SAL,
RealTek RT1318 and Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
This also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates"
* tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (417 commits)
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
ALSA: patch_realtek: Fix Dell Inspiron Plus 16
ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
ASoC: dt-bindings: Correct Alexandre Belloni email
ASoC: dt-bindings: maxim,max98504: Convert to DT schema
ASoC: dt-bindings: maxim,max98357a: Convert to DT schema
ASoC: dt-bindings: Reference common DAI properties
ASoC: dt-bindings: Extend name-prefix.yaml into common DAI properties
ASoC: rt715: Make read-only arrays capture_reg_H and capture_reg_L static const
ASoC: uniphier: aio-core: Make some read-only arrays static const
ASoC: wcd938x: Make read-only array minCode_param static const
ASoC: qcom: lpass-sc7280: Add maybe_unused tag for system PM ops
ASoC : SOF: amd: Add support for IPC and DSP dumps
ASoC: SOF: amd: Use poll function instead to read ACP_SHA_DSP_FW_QUALIFIER
ALSA: usb-audio: Workaround for XRUN at prepare
ALSA: pcm: Handle XRUN at trigger START
ALSA: pcm: Set missing stop_operating flag at undoing trigger start
drm: tda99x: Don't advertise non-existent capture support
ASoC: hdmi-codec: Allow playback and capture to be disabled
kselftest/alsa: Add more coverage of sample rates and channel counts
...
Coverity spotted that panic_info is not initialized to zero in
mtk_adsp_dump. Using uninitialized value panic_info.linenum when
calling snd_sof_get_status. Fix this coverity by initializing
panic_info struct as zero.
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20221213115617.25086-1-yc.hung@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason rt5670_i2c_probe() does a pm_runtime_put() at the end
of a successful probe. But it has never done a pm_runtime_get() leading
to the following error being logged into dmesg:
rt5670 i2c-10EC5640:00: Runtime PM usage count underflow!
Fix this by removing the unnecessary pm_runtime_put().
Fixes: 64e89e5f55 ("ASoC: rt5670: Add runtime PM support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221213123319.11285-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Advantech MICA-071 tablet deviates from the defaults for
a non CR Bay Trail based tablet in several ways:
1. It uses an analog MIC on IN3 rather then using DMIC1
2. It only has 1 speaker
3. It needs the OVCD current threshold to be set to 1500uA instead of
the default 2000uA to reliable differentiate between headphones vs
headsets
Add a quirk with these settings for this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221213123246.11226-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
This patchset is an alternative solution to problems
reported by Ricardo Ribalda <ribalda@chromium.org> and
Zhen Ni <nizhen@uniontech.com>, as discussed in
- "[PATCH] ALSA: core: Fix deadlock when shutdown a frozen userspace"
https://mailman.alsa-project.org/pipermail/alsa-devel/2022-November/209248.html
- "[PATCH] ASoc: SOF: Fix sof-audio-pci-intel-tgl shutdown timeout during hibernation"
https://mailman.alsa-project.org/pipermail/alsa-devel/2022-December/209685.html
It was raised by Oliver Neukum <oneukum@suse.com> that kernel should
not let user-space stall the shutdown process in any scenario and the
unregister call in current SOF shutdown code is not right.
This series reverts the ASoC SOF patch to unregister clients and
the machine drivers at shutdown. To avoid bringing back old bugs,
the series includes a patch to fix S5 entry on certain Intel
platforms.
The unique ID is determined by the ADR pin level of rt1318.
ODM changed design, update codec addr to match new design.
Fixes: 0050e3d3d4 ("ASoC: Intel: soc-acpi: add SKU 0C11 SoundWire configuration")
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221212085527.1886168-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rk_spdif_runtime_resume() may have called clk_prepare_enable() before return
from failed branches, add missing clk_disable_unprepare() in this case.
Fixes: f874b80e15 ("ASoC: rockchip: Add rockchip SPDIF transceiver driver")
Signed-off-by: Wang Jingjin <wangjingjin1@huawei.com>
Link: https://lore.kernel.org/r/20221208063900.4180790-1-wangjingjin1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix this by dropping wm8994->accdet_lock while calling
cancel_delayed_work_sync(&wm8994->mic_work) in wm1811_jackdet_irq().
Fixes: c0cc3f1665 ("ASoC: wm8994: Allow a delay between jack insertion and microphone detect")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221209091657.1183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In MT8195 SOF design, both DSP and audio driver would access audio
registers. Before DSP accesses audio registers, audio power and clock
should be enabled. DSP will hang up if DSP access audio register but
audio power and clock are disabled. Therefore, we add audio pm runtime
active checking before accessing audio registers in SOF BE's callback
hw_params function to avoid this situation.
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20221209031053.8444-1-yc.hung@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If system shutdown has not been completed cleanly, it is possible the
DMA stream shutdown has not been done, or was not clean.
If this is the case, Intel TGL/ADL HDA platforms may fail to shutdown
cleanly due to pending HDA DMA transactions. To avoid this, detect this
scenario in the shutdown callback, and perform an additional controller
reset. This has been tested to unblock S5 entry if this condition is
hit.
Co-developed-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221209114529.3909192-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the new style KAE keep-alive implementation is used on compatible
Intel hardware, the clocks are maintained when codec is in D3. The
generic code in hda_cleanup_all_streams() can however interfere with
generation of audio samples in this mode, by setting the stream and
channel ids to zero.
To get full benefit of the keepalive, set the new
no_stream_clean_at_suspend quirk bit on affected Intel hardware. When
this bit is set, stream cleanup is skipped in hda_call_codec_suspend().
Special handling is needed for the case when system goes to suspend. The
stream id programming can be lost in this case. This will also cause
codec->cvt_setups to be out of sync. Handle this by implementing custom
suspend/resume handlers. If keep-alive is active for any converter, set
the quirk flags no_stream_clean_at_suspend and forced_resume. Upon
resume, keepalive programming is restored if needed.
Fixes: 15175a4f2b ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-4-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the stream-id is zero, the keep-alive (KAE) will only ensure clock is
generated, but no audio samples are sent over display link. This happens
before first real audio stream is played out to a newly connected
receiver.
Reuse the code in silent_stream_enable() to set up stream parameters
to sane defaults values, also when using the newer keep-alive flow.
Fixes: 15175a4f2b ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-3-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The i915 display codec may not successfully transition to
normal audio streaming mode, if the stream id is programmed
while codec is actively transmitting data. This can happen
when silent stream is enabled in KAE mode.
Fix the issue by implementing a i915 specific programming
flow, where the silent streaming is temporarily stopped,
a small delay is applied to ensure display codec becomes
idle, and then proceed with reprogramming the stream ID.
Fixes: 15175a4f2b ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7353
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20221209101822.3893675-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Scenario when snd_hdac_stream_setup_periods() receives an instance of
struct hdac_stream with neither ->substream nor ->cstream initialized is
invalid.
Simultaneously addresses "uninitialized symbol 'dmab'" error reported by
Smatch.
Fixes: 3e9582267e ("ALSA: hda: Interrupt servicing and BDL setup for compress streams")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221208142635.1514944-1-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more updates for v6.2 which can hopefully go into a later pull
request, the bulk of these are fixes, minor cleanups or new board quirks
- the one big bit that isn't is support for getting diagnostic data out
of the Intel AVS firmwares.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOR9PIACgkQJNaLcl1U
h9C3wAf9FkTPVSSljH3u0mHDWrFjz4h+MRW8bzNGFmTSU9IEQwk2vjfXcSod1D8o
aDUhMVd1pGujc/1u6jk7virAG6IrT7mt0N6VHh4Qckxlj10EnAn/lVW0A/BWbtj3
j2j1AS1XxtYEdG0DQX7A4TAcdDysI1q66BEX3+kOlozAs8bn8Q1ZiEc2p2uaHKkY
pPNdvYQnZyxng4sQb2l3MmHtRAt3gwG6QC3VwAsGX1PNwlHqQNd6U2Tg9MQKP9q0
rwcUeutXcJihE576y+H7jsBpkopsIpSAl8Wb/LQzgDBfScY0YITPw/wUGNIUhNk7
LMNuJBQAQ66EyNJH58K2DrmXsSXOjA==
=lNJM
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.2
A few more updates for v6.2 which can hopefully go into a later pull
request, the bulk of these are fixes, minor cleanups or new board quirks
- the one big bit that isn't is support for getting diagnostic data out
of the Intel AVS firmwares.
DAIs parameters should be cleared if there's no active stream. Before,
we implemented it in soc_pcm_hw_free() by detecting stream_active. If
the running stream is the last active stream, we're going to clear
parameters.
However it will cause DAIs parameters never be cleared if there're
more than one stream. For example, we have stream1 and stream2 about
to stop. stream2 executes soc_pcm_hw_free() before stream1 executes
soc_pcm_close(). At the moment, stream2 should clear DAIs parameters.
Since stream_active is not yet updated by stream1 in soc_pcm_close(),
stream2 will not clear DAIs parameters. In result both stream1 and
stream2 don't clear the parameters.
This patch moves DAIs parameters cleanup after stream_active is
updated.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://lore.kernel.org/r/20221128060950.3540845-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function wcd_clsh_set_buck_mode() is defined in the wcd-clsh-v2.c
file, but not called elsewhere, so remove this unused function.
sound/soc/codecs/wcd-clsh-v2.c:133:20: warning: unused function 'wcd_clsh_enable_status'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3348
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221205073507.36071-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
One new JasperLake configuration, core refactoring between RT1316 and
RT1318 and a minor uninitialized variable corner case.
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Even though skylake-driver is going to be replaced by the avs-driver,
the goal is to keep it functional on all the configurations it supports
until its EOL. When comparing chrome trees against upstream
skylake-driver, couple fixes pop up that are not part of upstream
repository. These fixes are backed up by real bugs (issue trackers),
address real problems. There is no reason for them to stay in the
internal tree.
Patches 1-4 combined together address issue where the driver updates the
presumably static audio format descriptions coming from the topology
files through its "fixup" functions. As long as given audio format is
used by a single path, nothing collides and any updates are harmless.
However, when multiple paths e.g.: DMIC and HDMI1 utilize the same audio
format descriptor, any updates caused by the opening of the first path,
may cause the second to fail.
The 5th change from the set fixes driver hang sporadically occurring
during shutdown procedure. Once HDAudio links are powered down along
with the AudioDSP, the hang stops reproducing.
The last change helps survive in environments with limited/fragmented
memory. While the BDL is small already, other buffers can be allocated
using scatter-gather. This basically aligns the code with what the
avs-driver does.
The node returned by of_parse_phandle() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
error path in mt8183_mt6358_ts3a227_max98357_dev_probe().
Fixes: 11c0269017 ("ASoC: Mediatek: MT8183: Add machine driver with TS3A227")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1670234188-23596-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212051943476482106@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_disable_unprepare() should be called in the error handling of
rockchip_pdm_runtime_resume().
Fixes: fc05a5b222 ("ASoC: rockchip: add support for pdm controller")
Signed-off-by: Wang Jingjin <wangjingjin1@huawei.com>
Link: https://lore.kernel.org/r/20221205032802.2422983-1-wangjingjin1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_get_next_child() returns a node with refcount incremented, and
decrements the refcount of prev. So in the error path of the while loop,
of_node_put() needs be called for cpu_ep.
Fixes: fce9b90c1a ("ASoC: audio-graph-card: cleanup DAI link loop method - step2")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1670228127-13835-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The node returned by of_parse_phandle() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
error path in mt8173_rt5650_rt5514_dev_probe().
Fixes: 0d1d7a6642 ("ASoC: mediatek: Refine mt8173 driver and change config option")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1670234664-24246-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'ret' will not be initialized if dai_fmt is not DSP_A or DSP_B.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221206212507.359993-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sof_sdw_rt1308.c/sof_sdw_rt1316.c/sof_sdw_rt1318.c handle amp
in basically the same way, optimized and merged into one file.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221206212507.359993-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Resign from ->alloc_dma_buf() and use snd_dma_alloc_pages() directly.
For data i.e.: base firmware binary transfer, make use of SG allocation
to better adapt to memory-limited environment. For BDL descriptor, given
its small size this is not required.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AudioDSP cores and HDAudio links need to be turned off on shutdown to
ensure no communication or data transfer occurs during the procedure.
Fixes: c5a76a2469 ("ASoC: Intel: Skylake: Add shutdown callback")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a single location for pipe config selection where all fields
that have to be updated whenever ->pipe_config_idx changes can be
updated accordingly.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Field ->pipe_config_idx duplicates the job of ->cur_config_idx so
remove it.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than forcing userspace to select proper format with enumerable
kcontrols, select it ourselves based on provided hw_params.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Without updating the index before BE copier config is filled with
hardware parameters, outdated parameters are used instead.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihlaf.com>
Link: https://lore.kernel.org/r/20221205085330.857665-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI audio is not working on the HP EliteDesk 800 G6 because the pin is
unconnected. This issue can be resolved by using the 'hdajackretask'
tool to override the unconnected pin to force it to connect.
Signed-off-by: Jiao Zhou <jiaozhou@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221206185311.3669950-1-jiaozhou@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a fairly sedate release for the core code, but there's been a
lot of driver work especially around the x86 platforms and device tree
updates:
- More cleanups of the DAPM code from Morimoto-san.
- Factoring out of mapping hw_params onto SoundWire configuration by
Charles Keepax.
- The ever ongoing overhauls of the Intel DSP code continue, including
support for loading libraries and probes with IPC4 on SOF.
- Support for more sample formats on JZ4740.
- Lots of device tree conversions and fixups.
- Support for Allwinner D1, a range of AMD and Intel systems, Mediatek
systems with multiple DMICs, Nuvoton NAU8318, NXP fsl_rpmsg and
i.MX93, Qualcomm AudioReach Enable, MFC and SAL, RealTek RT1318 and
Rockchip RK3588
There's more cross tree updates than usual, though all fairly minor:
- Some OMAP board file updates that were depedencies for removing their
providers in ASoC, as part of a wider effort removing the support for
the relevant OMAP platforms.
- A new I2C API required for updates to the new I2C probe API.
- A DRM update making use of a new API for fixing the capabilities
advertised via hdmi-codec.
Since this is being sent early I might send some more stuff if you've
not yet sent your pull request and there's more come in.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOOO08ACgkQJNaLcl1U
h9BiIAf+O8zqcxtokSTS3wsoFHDp2zprTTUk3RZbxaYMFTmFrALbQVUx5EdJ179X
Dr9rL9T2iNBN7YGhDvmzoVvLrDncJEerMk7cgbc88a5tkB7ZipI7E9QliZt92QaP
ihrXAyD7ekLC6QLXrHFNmzwUeFspgtsBkT3MakcfcucuMN53UQbFwD1r0ziCJOMZ
gFnkZKBemUDsURxWR+LCveB/WYKNrZ6Bjokdg8HY1yenACMiXaoWedmIFJ2SxId3
NNS8vqUDUSEFhDaeJVBo1Ow9m8fe+dZBUeVk9Ej7bGEXxYptwtu3aODXknySa8Eb
YVlalR9qQPvaI1688WRleRWp+oyL4Q==
=x1AC
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.2
This is a fairly sedate release for the core code, but there's been a
lot of driver work especially around the x86 platforms and device tree
updates:
- More cleanups of the DAPM code from Morimoto-san.
- Factoring out of mapping hw_params onto SoundWire configuration by
Charles Keepax.
- The ever ongoing overhauls of the Intel DSP code continue, including
support for loading libraries and probes with IPC4 on SOF.
- Support for more sample formats on JZ4740.
- Lots of device tree conversions and fixups.
- Support for Allwinner D1, a range of AMD and Intel systems, Mediatek
systems with multiple DMICs, Nuvoton NAU8318, NXP fsl_rpmsg and
i.MX93, Qualcomm AudioReach Enable, MFC and SAL, RealTek RT1318 and
Rockchip RK3588
There's more cross tree updates than usual, though all fairly minor:
- Some OMAP board file updates that were depedencies for removing their
providers in ASoC, as part of a wider effort removing the support for
the relevant OMAP platforms.
- A new I2C API required for updates to the new I2C probe API.
- A DRM update making use of a new API for fixing the capabilities
advertised via hdmi-codec.
Since this is being sent early I might send some more stuff if you've
not yet sent your pull request and there's more come in.
I got a null-ptr-defer error report when I do the following tests
on the qemu platform:
make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m,
CONFIG_SND_MTS64=m
Then making test scripts:
cat>test_mod1.sh<<EOF
modprobe snd-mts64
modprobe snd-mts64
EOF
Executing the script, perhaps several times, we will get a null-ptr-defer
report, as follow:
syzkaller:~# ./test_mod.sh
snd_mts64: probe of snd_mts64.0 failed with error -5
modprobe: ERROR: could not insert 'snd_mts64': No such device
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6
Call Trace:
<IRQ>
snd_mts64_interrupt+0x24/0xa0 [snd_mts64]
parport_irq_handler+0x37/0x50 [parport]
__handle_irq_event_percpu+0x39/0x190
handle_irq_event_percpu+0xa/0x30
handle_irq_event+0x2f/0x50
handle_edge_irq+0x99/0x1b0
__common_interrupt+0x5d/0x100
common_interrupt+0xa0/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30
parport_claim+0xbd/0x230 [parport]
snd_mts64_probe+0x14a/0x465 [snd_mts64]
platform_probe+0x3f/0xa0
really_probe+0x129/0x2c0
__driver_probe_device+0x6d/0xc0
driver_probe_device+0x1a/0xa0
__device_attach_driver+0x7a/0xb0
bus_for_each_drv+0x62/0xb0
__device_attach+0xe4/0x180
bus_probe_device+0x82/0xa0
device_add+0x550/0x920
platform_device_add+0x106/0x220
snd_mts64_attach+0x2e/0x80 [snd_mts64]
port_check+0x14/0x20 [parport]
bus_for_each_dev+0x6e/0xc0
__parport_register_driver+0x7c/0xb0 [parport]
snd_mts64_module_init+0x31/0x1000 [snd_mts64]
do_one_initcall+0x3c/0x1f0
do_init_module+0x46/0x1c6
load_module+0x1d8d/0x1e10
__do_sys_finit_module+0xa2/0xf0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
The mts wa not initialized during interrupt, we add check for
mts to fix this bug.
Fixes: 68ab801e32 ("[ALSA] Add snd-mts64 driver for ESI Miditerminal 4140")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221206061004.1222966-1-cuigaosheng1@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The patchset focuses on debug functionality for the avs-driver.
Two major blocks are covered here: data probing and AudioDSP firmware
logging. Both are configured and controlled through debugfs.
Data probing is a AudioDSP debug functionality which allows for
gathering the actual data that is being routed to or from a module.
Helps in debugging its processing capabilities - navigate to a specific
module which may have caused a glitch within a pipeline (set of modules
bound together).
First few allow for assigning compress stream to a HDAudio stream, what
is currently limited to pcm substreams only. These patches were already
present on this list and reviewed in the past [1].
The next few tidy existing debug-related code up so it's ready for
addition of new functionalities and make it clear which part of the avs
is debug related and which is not. These also simplify the existing
locking around the trace fifo.
Afterward, debug-related IPCs are defined along with stub soc-component
and compress DAI operations. Not much is done there as it's not a
standard PCM streaming scenario. Most code found in compress operations
is inherited from the HOST side of HDAudio streaming found in pcm.c
file of the driver.
Finally, a debugfs file operations are defined. These facilitate
connecting to DSP modules from which the data shall be gathered as well
as control and configuration of firmware logging. Additionally, entries
are added to allow for dumping snapshots of key memory windows.
sof_es8336_remove() calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This
means that the callback function may still be running after
the driver's remove function has finished, which would result
in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Fixes: 89cdb224f2 ("ASoC: sof_es8336: reduce pop noise on speaker")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221205143721.3988988-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>:
Fix an issue with starting the ACP DSP and support debug dumps to aid
maintainability.
The Dell Inspiron Plus 16, in both laptop and 2in1 form factor, has top
speakers connected on NID 0x17, which the codec reports as unconnected.
These speakers should be connected to the DAC on NID 0x03.
Signed-off-by: Philipp Jungkamp <p.jungkamp@gmx.net>
Link: https://lore.kernel.org/r/20221205163713.7476-1-p.jungkamp@gmx.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HW platforms with multiple CS42L42 parts, faster CPU and i2c
requre some extra delay to allow PLL to settle and lock. Adding
extra 10ms delay.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221205145713.23852-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate the read-only arrays capture_reg_H and capture_reg_L
on the stack but instead make them static const. Also makes the
object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221202171450.1815346-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the read-only arrays slotsel_2ch, slotsel_multi, v_pll
and v_div on the stack but instead make them static const. Also makes
the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221202164156.1812971-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the read-only array minCode_param on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221202170644.1814720-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add __maybe_unused tag for system PM ops suspend and resume.
This is required to fix allmodconfig compilation issue.
Fixes: a3a96e93cc ("ASoC: qcom: lpass-sc7280: Add system suspend/resume PM ops")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1670219333-32526-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skyrim project and Whiterun met error when DSP
loading during device boot.
Ex, error in kernel log,
ERR kernel: [ 16.124537] snd_sof_amd_rembrandt
0000:04:00.5: PSP validation failed.
Use the snd_sof_dsp_read_poll_timeout function to successfully
read the FW_QUALIFIER register
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20221205120649.1950576-2-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SRAM0 window begins with a block of memory, usually of size PAGE_SIZE,
dedicated to the base firmware registers. When debugging firmware, it is
desirable to be able to dump them at will.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-16-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When user closes the tracer, some logs may still remain in the tail of
the buffer as firmware sends LOG_BUFFER_STATUS notification only when
certain threshold of data is reached. Add whatever is left to already
gathered logs so no information is lost.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-15-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define debugfs subdirectory delegated for IPC communication with DSP.
Input format: uint,uint,(...) which are later translated into DWORDS
sequence and further into instances of struct of interest given the IPC
type.
For Extractor probes, following have been enabled:
- PROBE_POINT_ADD (echo <..> probe_points)
- PROBE_POINT_REMOVE (echo <..> probe_points_remove)
- PROBE_POINT_INFO (cat probe_points)
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-14-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define stub component for data probing. Stub as most operations from
standard PCM case do not apply here. Specific bits are CPU DAIs and
compress_ops. FE DAIs can link against these new CPU DAI to create new
compress devices.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compress operations handlers for data extraction through probes. A
single HDAudio stream is enlisted for said purpose. Operations follow
same protocol as for standard PCM streaming on HOST side.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-11-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Data probing is a cAVS firmware functionality that allows for data
extraction and injection directly from or to DMA stream. To support it,
new functions and types are added. These facilitate communication
with the firmware.
Total of eight IPCs:
- probe module initialization and cleanup
- addition and removal of probe points
- addition and removal of injection DMAs
- dumping list of currently connected probe points or enlisted DMAs
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-10-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to debug-context aware wrappers instead of accessing debug
members directly allowing for readable separation of debug and non-debug
related code. Duplicates are removed along the way.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-9-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Without debug filesystem present, this code is redundant.
Operations: log_buffer_status and log_buffer_offset are left as is as
EXCEPTION_CAUGHT and even unexpected LOG_BUFFER_STATUS notifications may
occur without user ever touching debugfs.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Debug-related fields and log-dumping are useful when debugfs is enabled.
Define them under CONFIG_DEBUG_FS and provide stubs when the config is
disabled so that the code that makes use of these needs not to be
complicated unnecessarily.
Members that are duplicated by this patch will be removed by the follow
up changes.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Account for compress streams when receiving and servicing buffer
completed interrupts. In case of compress stream enlisting hdac_stream
for data transfer, setup BDL entries much like it is the case for PCM
streams.
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20221202152841.672536-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before introducing compress specific changes, adjust BDL and parameters
setup functions so these are not tightly coupled with PCM streams.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20221202152841.672536-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently only PCM streams can enlist hdac_stream for their data
transfer. Add cstream field to hdac_ext_stream to expose possibility of
compress stream assignment in place of PCM one.
Limited to HOST-type only as there no other users on the horizon.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20221202152841.672536-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Under certain situations (typically in the implicit feedback mode),
USB-audio driver starts a playback stream already at PCM prepare call
even before the actual PCM trigger-START call. For implicit feedback
mode, this effectively starts two streams for data and sync
endpoints, and if a coupled sync stream gets XRUN at this point, it
results in an error -EPIPE.
The problem is that currently we return -EPIPE error as is from the
prepare. Then application tries to recover again via the prepare
call, but it'll fail again because the sync-stop is missing. The
sync-stop is missing because it's an internal trigger call (hence the
PCM core isn't involved).
Since we'll need to re-issue the prepare in anyway when trapped into
this pitfall, this patch attempts to address it in a bit different
way; namely, the driver tries to prepare once again after syncing the
stop manually by itself -- so applications don't see the internal
error. At the second failure, we report the error as is, but this
shouldn't happen in normal situations.
Reported-and-tested-by: Carl Hetherington <lists@carlh.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b4e71631-4a94-613-27b2-fb595792630@carlh.net
Link: https://lore.kernel.org/r/20221205132124.11585-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver returns -EPIPE for indicating an XRUN already at PCM
trigger START, we should treat properly and set it to the XRUN state.
Otherwise the state is missing and the application would try to issue
trigger again without knowing that it's in an error state.
This is just for a theoretical bug, and it won't happen in most
cases.
Link: https://lore.kernel.org/r/b4e71631-4a94-613-27b2-fb595792630@carlh.net
Link: https://lore.kernel.org/r/20221205132124.11585-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM trigger-start fails at snd_pcm_do_start(), PCM core tries
to undo the action at snd_pcm_undo_start() by issuing the trigger STOP
manually. At that point, we forgot to set the stop_operating flag,
hence the sync-stop won't be issued at the next prepare or other
calls.
This patch adds the missing stop_operating flag at
snd_pcm_undo_start().
Fixes: 1e850beea2 ("ALSA: pcm: Add the support for sync-stop operation")
Link: https://lore.kernel.org/r/b4e71631-4a94-613-27b2-fb595792630@carlh.net
Link: https://lore.kernel.org/r/20221205132124.11585-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Mark Brown <broonie@kernel.org>:
The recently added pcm-test selftest has pointed out that systems with
the tda998x driver end up advertising that they support capture when in
reality as far as I can see the tda998x devices are transmit only. The
DAIs registered through hdmi-codec are bidirectional, meaning that for
I2S systems when combined with a typical bidrectional CPU DAI the
overall capability of the PCM is bidirectional. In most cases the I2S
links will clock OK but no useful audio will be returned which isn't so
bad but we should still not advertise the useless capability, and some
systems may notice problems for example due to pinmux management.
This is happening due to the hdmi-codec helpers not providing any
mechanism for indicating unidirectional audio so add one and use it in
the tda998x driver. It is likely other hdmi-codec users are also
affected but I don't have those systems to hand.
Mark Brown (2):
ASoC: hdmi-codec: Allow playback and capture to be disabled
drm: tda99x: Don't advertise non-existent capture support
drivers/gpu/drm/i2c/tda998x_drv.c | 2 ++
include/sound/hdmi-codec.h | 4 ++++
sound/soc/codecs/hdmi-codec.c | 30 +++++++++++++++++++++++++-----
3 files changed, 31 insertions(+), 5 deletions(-)
base-commit: f0c4d9fc9c
--
2.30.2
Currently the hdmi-codec driver always registers both playback and capture
capabilities but for most systems there's no actual capture capability,
usually HDMI is transmit only. Provide platform data which allows the users
to indicate what is supported so that we don't end up advertising things
to userspace that we can't actually support.
In order to avoid breaking existing users the flags in platform data are
a bit awkward and specify what should be disabled rather than doing the
perhaps more expected thing and defaulting to not supporting capture.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221130184644.464820-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMTP pin define headsets can be mis-detected as line out
instead of OMTP, causing obvious issues with audio quality.
This patch is to put increased resistances within
the device at a suitable point.
To solve this issue better, the new mechanism setup
ground switches with conditional delay control
and these allow for more stabile detection process
to operate as intended. This conditional delay control
will not impact the hardware process
but use extra system resource.
This commit improves control of ground switches in the AAD logic.
Signed-off-by: David Rau <david.rau.zg@renesas.com>
Link: https://lore.kernel.org/r/20221121050744.2278-1-david.rau.zg@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following a commit 1dd0dd0b1f ("ALSA: firewire: Remove some left-over
license text in sound/firewire"), this patch removes it added carelessly.
Fixes: 2133dc91d6 ("ALSA: dice: add support for Focusrite Saffire Pro 40 with TCD3070 ASIC")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221201030100.31495-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some more fixes for v6.1, some of these are very old and were originally
intended to get sent for v5.18 but got lost in the shuffle when there
was an issue with Linus not liking my branching strategy and I rebuilt
bits of my workflow. The ops changes have been validated by people
looking at real hardware and are how things getting dropped got noticed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOHg3AACgkQJNaLcl1U
h9AO+gf8C1E6GHk6UI3mU/xYCap0KgJavCVEJKExal2/pgCtCheC8OutFRAepsEM
mnbhfNImFEEkD/3YfdhH22XqavDE+fN0DSfFhkdiEbsfPTrHhc+PeWU8aQzEyOxT
tND7X01tmkWojmmoWJcVAv/z7hW1vF3FE/RUOiXHi3M7LhlJiSMy2ZkxHC9AEIz/
3jyahc2LbzZ5SuIo+c8kSoErg/mZ8zI2KlAGx3afpFAHUiGkSVWmhl4XOQ+1lozQ
dv4JtPMDx7SsM06GXUcvVTf6RI8QZQq6ohfz02BK7+NqD+odRrg3WlbabcTLvi1k
LpNg5saPWYx8JVwHu9ggLtNfE5TAVQ==
=T8ew
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.1-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.1
Some more fixes for v6.1, some of these are very old and were originally
intended to get sent for v5.18 but got lost in the shuffle when there
was an issue with Linus not liking my branching strategy and I rebuilt
bits of my workflow. The ops changes have been validated by people
looking at real hardware and are how things getting dropped got noticed.
TC Applied Technologies (TCAT) produces TCD3070 as final DICE ASIC for
communication in IEEE 1394 bus for IEC 61883-1/6 protocol. As long as I
know, latter model of Focusrite Saffire Pro 40 is an application of the
ASIC and only in the market for consumers.
This patchset adds support for the device. The device has several
remarkable points.
1. No support for extended synchronization information section in TCAT
general protocol. The value of GLOBAL_EXTENDED_STATUS register is always
zero. Additionally, NOTIFY_EXT_STATUS message is never emitted.
2. No support for TCAT protocol extension. Hard coding is required for
format of CIP payload.
3. During several seconds after changing sampling rate, the block to
process PCM frames is under disfunction. When starting packet streaming
during the state, the block is never function till configuring different
sampling rate and several seconds.
This commit adds support for the device. The item 1 and 2 can be
adaptable, while item 3 is not. It's not preferable that user process
is forced to sleep during the disfunction in the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS or SNDRV_PCM_IOCTL_PREPARE request. It's
inconvenient but let user configure preferable sampling rate in advance
of starting PCM substream.
The content of configuration ROM in the device I used is available at:
* https://github.com/takaswie/am-config-roms/
I note that any mixer control operation is implemented by unique
transaction. The frame of request consists of 16 bytes header followed
by payload.
header (4 quadlets):
1st: the type of request, prefixed with 0x8000
2nd: counter at 2 bytes in MSB side, the length of data at 2 bytes in LSB
side
3rd: parameter 0
4th: parameter 1
payload (variable length if need):
5th-: data according to parameters
The request frame is sent by block write request to 0x'ffff'e040'01c0.
The frame of response is similar to the frame of request, but it is
header only, thus fixed to 16 bytes. The response frame is sent to the
address which is registered by lock transaction to 0x'ffff'e040'0008.
If the operation results in batch of data, the 2nd quadlet of header
includes the length of data like request. The data is itself readable
by read block request to 0x'ffff'e040'0030, which includes both
header and payload for data, thus the length to read should be the
length of data plus 16 bytes for header
The actual value of request, parameter 0, parameter 1, and data is
unclear yet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130143313.43880-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Lexicon I-ONIX FW810S, the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS can returns -ETIMEDOUT. This is a regression due
to the commit 41319eb56e ("ALSA: dice: wait just for
NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation"). The device
does not emit NOTIFY_CLOCK_ACCEPTED notification when accepting
GLOBAL_CLOCK_SELECT operation with the same parameters as current ones.
This commit fixes the regression. When receiving no notification, return
-ETIMEDOUT as long as operating for any change.
Fixes: 41319eb56e ("ALSA: dice: wait just for NOTIFY_CLOCK_ACCEPTED after GLOBAL_CLOCK_SELECT operation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130130604.29774-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model requires an additional detection quirk to enable the
internal microphone - BIOS doesn't seem to support AcpDmicConnected
(nothing in acpidump output).
Signed-off-by: Artem Lukyanov <dukzcry@ya.ru>
Link: https://lore.kernel.org/r/20221130085247.85126-1-dukzcry@ya.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
If we do not shutdown the peripheral properly at shutdown, the whole system
crashes after kexec() on the first io access.
Let's implement the appropriate callback.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221127-mtk-snd-v1-0-b7886faa612b@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Leftover from recent series [1].
Following changes are proposed for the rt5682 sound card driver:
1) Move jack unassignment from platform_device->remove() to
dai_link->exit(). This is done to make jack init and deinit flows
symmetric
2) Remove platform_device->remove() function
3) Simplify card->suspend_pre() and card->resume_post() by making use of
snd_soc_card_get_codec_dai() helper
Use link->exit() rather than pdev->remove() to unassign jack during card
unbind procedure so codec link initialization and exit procedures are
symmetrical.
Also, there is no need to perform search for codec dai in suspend_pre()
and resume_post() ourselves. Use snd_soc_card_get_codec_dai() instead.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221129180738.2866290-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following commits will make use of it to find codec DAI, define it
first.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221129180738.2866290-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:f086ba9d5389c ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160402.126140-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
For all the boards included in this patchset, a similar set of changes
is proposed:
1) Move jack unassignment from platform_device->remove() to
dai_link->exit(). This is done to make jack init and deinit flows
symmetric
2) Remove platform_device->remove() function
3) Simplify card->suspend_pre() and card->resume_post() by making use of
snd_soc_card_get_codec_dai() helper
While bdw_rt286 board - which is utilized by the catpt-driver - is
definitely not part of "avs", same treatment applies. And thus decided
to make it part of this series instead of sending it separately.
Add __maybe_unused tag for system PM ops suspend and resume.
This is required to fix allmodconfig compilation issue.
Fixes: a3a96e93cc ("ASoC: qcom: lpass-sc7280: Add system suspend/resume PM ops")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1669726428-3140-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tascam's Model 12 is a mixer which can also operate as a USB audio
interface. The audio interface uses explicit feedback but it seems that
it does not correctly handle missing isochronous frames.
When injecting an xrun (or doing anything else that pauses the playback
stream) the feedback rate climbs (for example, at 44,100Hz nominal, I
see a stable rate around 44,099 but xrun injection sees this peak at
around 44,135 in most cases) and glitches are heard in the audio stream
for several seconds - this is significantly worse than the single glitch
expected for an underrun.
While the stream does normally recover and the feedback rate returns to
a stable value, I have seen some occurrences where this does not happen
and the rate continues to increase while no audio is heard from the
output. I have not found a solid reproduction for this.
This misbehaviour can be avoided by totally resetting the stream state
by switching the interface to alt 0 and back before restarting the
playback stream.
Add a new quirk flag which forces the endpoint and interface to be
reconfigured whenever the stream is stopped, and use this for the Tascam
Model 12.
Separate interfaces are used for the playback and capture endpoints, so
resetting the playback interface here will not affect the capture stream
if it is running. While there are two endpoints on the interface,
these are the OUT data endpoint and the IN explicit feedback endpoint
corresponding to it and these are always stopped and started together.
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221129130100.1257904-1-john@metanate.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use link->exit() rather than pdev->remove() to unassign jack during card
unbind procedure so codec link initialization and exit procedures are
symmetrical.
Also, there is no need to perform search for codec dai in suspend_pre()
and resume_post() ourselves. Use snd_soc_card_get_codec_dai() instead.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-10-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following commits will make use of it to find codec DAI, define it
first.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-9-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use link->exit() rather than pdev->remove() to unassign jack during card
unbind procedure so codec link initialization and exit procedures are
symmetrical.
Also, there is no need to perform search for codec dai in suspend_pre()
and resume_post() ourselves. Use snd_soc_card_get_codec_dai() instead.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following commits will make use of it to find codec DAI, define it
first.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use link->exit() rather than pdev->remove() to unassign jack during card
unbind procedure so codec link initialization and exit procedures are
symmetrical.
Also, there is no need to perform search for codec dai in suspend_pre()
and resume_post() ourselves. Use snd_soc_card_get_codec_dai() instead.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
