This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77965
SoC.
Based on a similar patch of the R8A7796 PFC driver
by Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a build-time check, to ensure the register and field widths in
descriptors for config registers with fixed-width fields are sane.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are two pin groups for the FSIC SPDIF signal, but the FSIC pin
group array lists only one, and it refers to a nonexistent group.
Fixes: 2ecd4154c9 ("sh-pfc: sh73a0: Add FSI pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_data18_b pin group itself is present, but it is not listed in
the VIN1 pin group array, and thus cannot be selected.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a
typo, thus the group cannot be selected.
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The err_rst_reqb, ext_clki, lowpwr, and ref_clko pin groups are present,
but no pinmux functions refer to them, hence they can not be selected.
Fixes: 1e7d5d849c ("sh-pfc: Add emev2 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When declaring the HSPI RX1_B and TX1_B pins, two mistakes were made:
- the rows and columns in the BGA pin matrix, from which the pin
numbers are derived, were exchanged,
- it was not taken into account that pin row labelling skips
characters I, O, Q, and S.
Fix the order, and the corresponding pin names.
Notes:
- The actual values of the pin numbers don't really matter (they just
have to be unique), so the wrong order didn't have any impact,
- Changing the names of the pins is user-visible, but there are no
users in (upstream) DTS files.
Fixes: 4f82e3ee72 ("sh-pfc: Support pins not associated with a GPIO port")
Fixes: 09cc76a958 ("sh-pfc: r8a7778: add HSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Unlike R-Car M3-W, R-Car M3-N does not have DU_DOTCLKIN2, but the
corresponding pin carries the DU_DOTCLKIN3 signal. Correct all
references to DU_DOTCLKIN2 to fix this.
This change does not have any runtime effect, as it only changes an
internal enum name, and a comment.
Fixes: 490e687eb8 ("pinctrl: sh-pfc: Initial R-Car M3-N support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The naming of the "b" versions of the VIN1 pin groups is a bit odd, in
that the "_b" appears in the middle of the names, instead of as a
suffix.
Increase consistency with other SoCs by making R-Car M2-W and M2-N, and
RZ/G1M and RZ/G1N, use the recently added optional "version" argument of
the VIN_DATA_PIN_GROUP() macro.
Note that this breaks backwards compatibility with existing DTBs, but
there are no upstream users of the "vin1_b_*" names.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN1 channel.
This reduces kernel size by 144 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data12 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN0 and VIN1 channels.
This reduces kernel size by 288 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Use union vin_data16 and VIN_DATA_PIN_GROUP() to reduce redundancies in
pin definitions for the VIN5 channel.
This reduces kernel size by 240 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.35 in R-Car E2 v0.5). However, the reset value of the register is 0,
so software has to do it. Add this to the kernel driver to ensure this
is really done independent of firmware versions and use whitelisting for
ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Documentation for ES1.0 says that some bits in TDSEL must be set (ch
5.3.39 in R-Car H2 v0.91). However, the reset value of the register is
0, so software has to do it. Add this to the kernel driver to ensure
this is really done independent of firmware versions and use
whitelisting for ES versions known to need this.
This is needed for some SD cards supporting SDR104 transfer mode. For
me, TDSEL was not initialized by the firmware and I had problems with
the card when re-inserting it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Knowing which pin group is being configured is useful information when
debugging pin configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit f4caa6ee73.
The same can be expressed better by dropping the
SH_PFC_PIN_CFG_PULL_DOWN flag from the GPIO description, as it includes
returning an error to the caller when trying to configure the pin for
pull-down, causing:
sh-pfc e6060000.pin-controller: pin_config_set op failed for pin 201
sh-pfc e6060000.pin-controller: Error applying setting, reverse things back
sh-pfc e6060000.pin-controller: failed to select default state
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car D3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] D3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
[shimoda: split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use a macro to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
MOD_SEL register bit numbering was different from R-Car E3 SoC and
R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'0 b'0
Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'00 b'00
Set Value = H'1 b'01 b'10
Set Value = H'2 b'10 b'01
Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3
=============== ========== =====
Set Value = H'0 b'000 b'000
Set Value = H'1 b'001 b'100
Set Value = H'2 b'010 b'010
Set Value = H'3 b'011 b'110
Set Value = H'4 b'100 b'001
Set Value = H'5 b'101 b'101
Set Value = H'6 b'110 b'011
Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
[shimoda: Split a patch per SoC and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[geert: Use macros to do the actual reordering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and
SCK2_A pin functions are selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is
selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
pinmux_cfg_reg.var_field_width[] is actually a variable-length array,
terminated by a zero, and counting at most r_width entries.
Usually the number of entries is much smaller than r_width, so the
ability to catch bugs at compile time through an "excess elements in
array initializer" warning is fairly limited.
Hence make the array variable-length, decreasing kernel size slightly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The debug code in sh_pfc_write_config_reg() prints the width of the
field being modified.
However, registers with a variable-width field layout are identified by
pinmux_cfg_reg.field_width being zero, hence zeroes are printed instead
of the actual field widths.
Fix this by printing the Hamming weight of the field mask instead, which
is correct for both fixed-width and variable-width fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc421 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
While the SEL_PWM[0-3] fields in the Module Select Register 0 support 4
possible configurations per PWM pin, only the first 3 are valid.
Replace the invalid and unused configurations for SEL_PWM[0-3]_3 by
dummies.
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: f59125248a ("pinctrl: sh-pfc: Add R8A77980 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 9 contains 12 fields, but the
variable field descriptor contains a 13th bogus field of 3 bits.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a build-time check, to ensure the number of pins and pin marks in a
pin group matches. This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The tpu4_to3_mux[] array contains the TPU4TO3 pin mark, but the
tpu4_to3_pins[] array lacks the corresponding pin number.
Add the missing pin number, for non-GPIO pin F26.
Fixes: 5da4eb049d ("sh-pfc: sh73a0: Add TPU pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The lcd0_data24_1_pins[] array contains the LCD0 D1[2-5] pin numbers,
but the lcd0_data24_1_mux[] array lacks the corresponding pin marks.
Fixes: 06c7dd866d ("sh-pfc: r8a7740: Add LCDC0 and LCDC1 pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The gether_gmii_mux[] array contains the REF125CK pin mark, but the
gether_gmii_pins[] array lacks the corresponding pin number.
Fixes: bae11d30d0 ("sh-pfc: r8a7740: Add GETHER pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Due to an interaction with commit 9f2b76a2db ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control
Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3.
Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
Fixes: 33847a7137 ("pinctrl: sh-pfc: r8a77990: Add voltage switch operations for SDHI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018) states
that the USB30_OVC pin supports pull-up only. It has a bit assigned in
the pull-enable register (PUEN5), but not in the pull-up/down control
register (PUD5).
Add a check for this, to prevent configuring a prohibited setting.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 83f6941a42 ("pinctrl: sh-pfc: r8a77990: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the QSPI{0|1} pins/groups/functions to the R8A77980 PFC driver.
[Sergei: ported to the upstream driver, fixed up the swapped QSPI0 SPCLK/
SSL pins, fixed up the comments, moved the QSPI pins/groups/functions to
be in the alphanumeric order, removed unneeded empty lines, renamed the
patch.]
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[geert: Move canfd from common to automotive]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77965
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN{0,1} pins, groups and functions to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
