The r8a7790 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The emev2 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently all PFC registers lie in low 32-bit address space. Hence use
u32 instead of unsigned long to store PFC register addresses in pinctrl
tables. All calculations of virtual addresses use a phys_addr_t
intermediate, so we know where to add an offset if the 32-bit assumption
ever becomes false.
While this doesn't impact 32-bit builds, it would save ca. 7 KiB on a
64-bit shmobile_defconfig kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All other loops over sh_pfc_soc_info.data_regs[] use
pinmux_data_reg.regwidth as the sentinel, which is safer as zero is
never a valid regwidth value (reg could be zero if we start using it to
store an offset).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As register and field widths and offsets are in the range 1..32, use
unsigned int (mostly replacing unsigned long) to store them in local
variables and for passing them around.
Move to one variable per line, move variables to the beginning of the
block where they are used, and drop superfluous initializations while we
are at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Register and field widths are in the range 1..32. Storing them in the
pinctrl data in (arrays of) unsigned long wastes space.
This decreases the size of a (32-bit) shmobile_defconfig kernel
supporting 7 SoCs by 26460 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As PFC registers are either 8, 16, or 32 bits wide, use u32 (mostly
replacing unsigned long) to store (parts of) register values and masks.
Switch the shadow register operations from {set,clear}_bit() to plain C
bit operations, as the former can operate on long data only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the last user of the in_pd/in_pu bias parameters of the _PCRH()
macro was removed in commit 80da8e02d2 ("sh-pfc: r8a7740: Add bias
(pull-up/down) pinconf support"), bias parameters are supposed to be
configured using the generic pinctl mechanism, which calls the
.set_bias() method.
However, the PORTCR() macro still represents the control register as
consisting of two 4-bit fields. Hence the bias configuration in the
uppermost 2 bits is always overwritten with zeroes when a pin is
configured for GPIO, disabling any previously configured bias.
Use the variable config register macro instead, to represent the
register as having 4 fields, and to make sure only the input/output
control and function fields are touched.
This affects R-Mobile APE6 (r8a73a4), R-Mobile A1 (r8a7740), SH-Mobile
AP4 (sh7372), and SH-Mobile AG5 (sh73a0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r8a7791 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove sh7372 PFC support as part of the sh7372 and Mackerel
legacy code removal.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PFC support for the EMMA Mobile EV2 SoC including pin groups for
on-chip devices.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Used to define pinmux configurations where the pinmux function have no
representation in the configuration registers but instead solely depends
on a group selection.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MLB+ 3-pin mode pin group to R8A7790 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MLB+ 3-pin mode pin group to R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R8A7791 manual sometimes calls the signal MLB_CLK and sometimes MLB_CK; the
latter can only be encountered in the PFC section and is probably just a typo
(this signal is always called MLB_CLK in the R8A7790 manual). Fix occurences
of MLB_CK throughout the R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.
To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.
Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.
v2:
- fix typo
- add missing documentation for @conf_items member in struct
- rebase to pinctrl/devel: conflict in abx500
- rename _pinconf_generic_dump() to pinconf_generic_dump_one()
- removed '_' from _parse_dt_cfg()
- removed BUG_ONs, error condition is handled in if statements
- removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
helpers
- fixed up corresponding call sites
- renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
- added kernel-doc to pinconf_generic_dump_pins()
- add kernel-doc
- more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
development series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084
pin controllers.
- Incremental new features on the Rockchip, atlas 6,
OMAP, AM437x, APQ8064, prima2, AT91, Tegra, i.MX, Berlin
and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b4Tn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.18 development
series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084 pin
controllers.
- Incremental new features on the Rockchip, atlas 6, OMAP, AM437x,
APQ8064, prima2, AT91, Tegra, i.MX, Berlin and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes"
* tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: specify bindings for pins and groups
pinctrl: nomadik: improve GPIO debug prints
pinctrl: abx500: refactor DT parser to take two paths
pinctrl: abx500: use helpers for map allocation/free
pinctrl: alter device tree bindings for functions
pinctrl: nomadik: refactor DT parser to take two paths
pinctrl: nomadik: use utils map free function
pinctrl: nomadik: use util function to reserve maps
pinctrl: qcom: use restart_notifier mechanism for ps_hold
pinctrl: sh-pfc: sh73a0: Remove unnecessary SoC data allocation
pinctrl: berlin: fix the dt_free_map function
pinctrl: at91: disable PD or PU before enabling PU or PD
pinctrl: st: remove gpiochip in failure cases
pinctrl: at91: Fix error handling while doing gpiochio_irqchip_add
pinctrl: at91: Fix failure path in at91_gpio_probe path
pinctrl: lantiq: Release gpiochip resources in fail case
pinctrl: imx: detect uninitialized pins
pinctrl: tegra: Add MIPI pad control
pinctrl: at91: Switch to using managed clk_get
pinctrl: adi2: Remove duplicate gpiochip_remove_pin_ranges
...
The SoC data structure allocated at init time only holds a regulator
pointer that is only used in the init function. Replace it with a local
variable and get rid of the SoC data structure allocation altogether.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vtable named *pinmux_ops in the affected files are not really
about pin multiplexing, but a struct related to some PFC-specific
operations, inclusing pin config (bias setting). Rename the variable
so as to avoid confusions.
Acked-by: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I had made last-minute changes before submitting the patch "sh-pfc: r8a7791:
add CAN pin groups"; now I'm seeing that they weren't complete: I had missed
update to the pin group names in pin[01]_groups[]. Drop the "_a" suffixes there.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves data allocated using regulator_register to
devm_regulator_register and does away the calls to regulator_unregister.
The sh73a0_pinmux_soc_exit function is no longer needed and is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
development cycle:
- Antoine Tenart made the get_group_pins() vtable entry
optional.
- Antoine also provides an entirely new driver for the
Marvell Berlin SoC. This is unrelated to the existing
MVEBU hardware driver and warrants its own separate
driver.
- Reflected from the GPIO subsystem there is a number of
refactorings to make pin control drivers with gpiochips
use the new gpiolib irqchip helpers. The following
drivers were converted to use the new infrastructure:
- ST Microelectronics STiH416 and friends
- The Atmel AT91
- The CSR SiRF (Prima2)
- The Qualcomm MSM series
- Massive improvements in the Qualcomm MSM driver from
Bjorn Andersson, Andy Gross and Kumar Gala. Among those
new support for the IPQ8064 and MSM8x74 SoC variants.
- Support for the Freescale i.MX6 SoloX SoC variant.
- Massive improvements in the Allwinner sunxi driver from
Boris Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori
Morimoto, Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from
Stepgen Warren.
- The Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- The MVEBU driver now supports the Orion5x SoC
variants, which is part of the effort of getting rid of
the old Marvell kludges in arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- A ton of cleanups and janitorial patches from Axel Lin.
- Some minor fixes and improvements here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wGE5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.16 development
cycle:
- Antoine Tenart made the get_group_pins() vtable entry optional.
- Antoine also provides an entirely new driver for the Marvell Berlin
SoC. This is unrelated to the existing MVEBU hardware driver and
warrants its own separate driver.
- reflected from the GPIO subsystem there is a number of refactorings
to make pin control drivers with gpiochips use the new gpiolib
irqchip helpers. The following drivers were converted to use the
new infrastructure:
* ST Microelectronics STiH416 and friends
* The Atmel AT91
* The CSR SiRF (Prima2)
* The Qualcomm MSM series
- massive improvements in the Qualcomm MSM driver from Bjorn
Andersson, Andy Gross and Kumar Gala. Among those new support for
the IPQ8064 and MSM8x74 SoC variants.
- support for the Freescale i.MX6 SoloX SoC variant.
- massive improvements in the Allwinner sunxi driver from Boris
Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori Morimoto,
Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from Stepgen
Warren.
- the Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- the MVEBU driver now supports the Orion5x SoC variants, which is
part of the effort of getting rid of the old Marvell kludges in
arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- a ton of cleanups and janitorial patches from Axel Lin.
- some minor fixes and improvements here and there"
* tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: sirf: fix a bad conflict resolution
pinctrl: msm: Add more MSM8X74 pin definitions
pinctrl: qcom: ipq8064: Fix naming convention
pinctrl: msm: Add missing sdc1 and sdc3 groups
pinctrl: sirf: switch to using allocated state container
pinctrl: Enable "power-source" to be extracted from DT files
pinctrl: sunxi: create irq/pin mapping during init
pinctrl: pinconf-generic: Use kmemdup instead of kmalloc + memcpy
pinctrl: berlin: Use devm_ioremap_resource()
pinctrl: sirf: fix typo for GPIO bank number
pinctrl: sunxi: depend on RESET_CONTROLLER
pinctrl: sunxi: fix pin numbers passed to register offset helpers
pinctrl: add pinctrl driver for imx6sx
pinctrl/at91: Fix lockup when IRQ on PIOC and PIOD occurs
pinctrl: msm: switch to using generic GPIO irqchip helpers
pinctrl: sunxi: Fix multiple registration issue
pinctrl: sunxi: Fix recursive dependency
pinctrl: berlin: add the BG2CD pinctrl driver
pinctrl: berlin: add the BG2 pinctrl driver
pinctrl: berlin: add the BG2Q pinctrl driver
...
In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.
This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a missing 0 entry from the MOD_SEL3 table.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The extra entry in the table makes SCIFA0_B, and all
peripherals after it, fail.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the muxing for the last missing i2c rcar core. Fix the sorting for
SH_PFC_PIN_NAMED while we are here.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DU parallel interface ODDF signal is optional, move it out of the
HSYNC/VSYNC group into a group of its down. The CDE and DISP signals are
independent, split them to two different groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the
STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung),
sunxi (AllWinner), i.MX (Freescale), Baytrail.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7Sq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk changes from Linus Walleij:
"Pin control bulk changes for the v3.15 series, no new core
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung), sunxi
(AllWinner), i.MX (Freescale), Baytrail"
* tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: tegra: add some missing Tegra114 entries
pinctrl: tegra: fix some mistakes in Tegra124
pinctrl: msm: fix up out-of-order merge conflict
pinctrl: st: Fix error check for of_irq_to_resource usage
pinctrl: tegra: consistency cleanup
pinctrl: tegra: dynamically calculate function list of groups
pinctrl: tegra: init Tegra20/30 at module_init time
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
pinctrl: st: add pinctrl support for the STiH407 SoC
pinctrl: st: Enhance the controller to manage unavailable registers
pinctrl: msm: Simplify msm_config_reg() and callers
pinctrl: msm: Remove impossible WARN_ON()s
pinctrl: msm: Replace lookup tables with math
pinctrl: msm: Drop OF_IRQ dependency
pinctrl: msm: Drop unused includes
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
pinctrl: msm: Silence recursive lockdep warning
pinctrl: mvebu: silence WARN to dev_warn
pinctrl: msm: drop wake_irqs bitmap
pinctrl-baytrail: add function mux checking in gpio pin request
...
Fix the SD1_CLK handling for r8a7791. Without this patch
it is impossible to request all pins needed for SDHI1 on
the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a new group for the USB0 OVC/VBUS pin by itself. This
allows us to monitor PWEN as GPIO on the Lager board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
- New driver for the Qualcomm TLMM pin controller and its
msm8x74 subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and
GPIO drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf
driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC"
driver and associated subdrivers as usual. It is settling
down a little bit now it seems.
- Minor fixes and incremental updates here and there as usual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ol2E
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
