When the host->tuning_count is zero it means that the retuning is
disabled. This is checked on the first run of sdhci_execute_tuning()
by the if statement below:
if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
(host->tuning_mode == SDHCI_TUNING_MODE_1)) {
So only when tuning_count is non-zero it will set the host flag
SDHCI_USING_RETUNING_TIMER. The else statement is only for re-programming
the timer, which means that flag must be set. Because that is not checked
the else statement is executed in the first run when tuning_count is zero.
This was seen on a host controller which indicated SDHCI_TUNING_MODE_1 (0)
and tuning_count being zero. Suspect that (one of) these registers is not
properly set.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
If the SDHCI irq is shared with another device then the interrupt
handler can get called while SDHCI is runtime suspended. That is
harmless but the warning message is not useful so remove it. Also
returning IRQ_NONE is more appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>
The driver has a timer with a 10 second timeout to catch devices that stop
responding. However it is possible for commands to take even longer than
that. Change the timer timeout to reflect the command timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
In function sdhci_request(), it is possible to do the tuning execution
like below:
sdhci_request() {
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
spin_unlock_irqrestore(&host->lock, flags);
<=== Here it is possible one pending finish_tasklet get running
and it will operate the original mrq, and notified the mrq
is done, and causes memory corruption.
sdhci_execute_tuning(mmc, tuning_opcode);
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
}
In the above race place, the original mrq should not be finished wrongly,
so here before unlock the spinlock, we need to set the host->mrq to NULL
to avoid this case.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The auto cmd settings bits should be cleared before sending new commands
or we may receive command timeout error for normal commands due to wrongly
pre-sent auto cmd.
e.g. we receive CMD13 timeout error due to ACMD23 is wrongly enabled
by former data commands.
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2 p3 p4 < p5 p6 p7 >
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot1: unknown partition table
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot0: unknown partition table
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ignore Card Interrupt bit in the interrupt status if we already
know that mmc_signal_sdio_irq() is going to be called at the end of
sdhci_irq(). This avoids a needless loop in sdhci_irq() repeatedly
reading interrupt status and doing nothing.
Signed-off-by: Alexey Neyman <stilor@att.net>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original code missed to report an error when the maximum tuning
loops exhausted or timeout, it will cause the upper layer to wrongly
think the tuning process is passed.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It helps for platform code to use it send tuning commands.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tuning of some platforms may not follow the standard host control
spec v3.0, e.g. Freescale uSDHC on i.MX6Q/DL.
Add a hook here to allow execute platform specific tuning instead of
standard host controller tuning.
The hook only replaces the tuning process, so it's placed after tuning
checking and before the real tuning process.
Some notes for the tuning hook:
1) it needs handle lock itself if it wants to access host controller
according platform specific implementation.
2) do not need to handle runtime pm since it executes with runtime pm
get already.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJSLxu8AAoJEHNBYZ7TNxYMkV8P/RZMkP3L88wPmvdQ4IxVD/Bg
jphPsZTAlY8pLY7EcBVfbIGfBMMoVZ8CayuAbj9u5jFiMBNDUKRnKrky1m95F62n
xXiS5vUiKdWpByMpfKmrqvJr6eS8SWq5z/yug1c3s1Y9T363KgfypgJLvNgbMGiv
qbmjE+Zw65nMwHCk+4Rvq6s4aN6KosRZP0ABsn1foXt3kybSgemp5ShrlEyXohfS
E91EiYxHFC4fdmuWiZZvL1tyHFeV25omyZA90mpkioNItiwoyOM2rfjfEfNq+WBw
UrmdBesbGsF0Zi12CBa9LtzdRjYK8PugBWKW3mycS5++NX9KW6Ac/EpGqFeH9KgL
WZ2v4aQjkbnzQKUB2HcWAyXm88G9MkNvpLbIrmIPtson+q0UjgPYWe5BI3dy/Y1v
YS1JeseslVtSTKzGYsa1GJ7Nc1xYiILRz0RS4YGYXNjwvrl89i2UH7cglYDW36Xd
vxvRBaFpVsj1mfjjITEoG6nE0v5aYH6gSITY79XR+/kN871/99/oIUaWdpjcm9yv
SIYmK7ipcvxugkQ7BoMGbym/dvuUrZ+Vnf8dFlGPTJegZVsnfgrVAnRpvcVwW8+x
4Z79wUPSIETRqj2XX2I/Y0JnrXry+dLLVyeK1tELoeOKev73Ai2lcqPSz6J0tzJs
IErcz0hM1znL2RtgNwio
=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
We use host->ocr_mask to hold the voltage get from device-tree
node, In case host->ocr_mask was available, we use host->ocr_mask
as the final available voltage can be used by MMC/SD/SDIO card.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Add a card_event callback to sdhci so that clients can provide their
own card_event to be called when card_detect is triggered.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the HC ctrl_2 programming where, in case of
SDR104 and HS200, we have to write 100b in the the UHS Mode
bits. We wrote 101b that is reserved from Arasan Specs.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Although the HC supports HS200 (eMMC) the caps2 are always zero; this
means there's no way to use the super speed mode (when init the card).
If the HC support SDR104, for SD3.0, so it also supports HS200 for eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The following error randomly appears on an imx6q board where gpio is
used to implement card-detection when mounting EXT4 rootfs during boot.
mmc1: Card removed during transfer!
mmc1: Resetting controller.
mmcblk0: unknown error -123 sending read/write command, card status 0x900
end_request: I/O error, dev mmcblk0, sector 106744
EXT4-fs error (device mmcblk0p2): ext4_find_entry:1312: inode #5011: comm swapper/0: reading directory lblock 0
It turns out that the error message comes from the card removal check
in function sdhci_card_event(). While we have a well implemented
function sdhci_do_get_cd() handling all the possible cases of
CD, the current code only checks controller internal CD case. That
causes problem for other CD cases like gpio on above imx6q board.
Improve the check by using sdhci_do_get_cd() to cover all possible CD
cases, so that above error on the imx6q board gets fixed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If card power is dependent on SD bus power then the host controller
must not be runtime suspended while the card is powered up. Add
the ability to stay runtime-resumed in that case and enable it with a new
quirk SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
/git/arm-soc/drivers/mmc/host/sdhci.c: In function 'sdhci_add_host':
/git/arm-soc/drivers/mmc/host/sdhci.c:2910:19: warning: ignoring
return value of 'regulator_enable', declared with attribute
warn_unused_result [-Wunused-result]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
1. mmc_rescan will call get_cd to know whether the card is present
before mmc_rescan_try_freq to avoid useless trials during
card removal or start host is called when card is not present.
2. get_cd needs to be checked to resolve slow card removal issue.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:
drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]
Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The protocol related code is moved to core stack. So update the host
driver accordingly.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Tim Wang <wangtt@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are three places where same piece of code is used. Let's split it
to a separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Don't disable SD Host IRQ during suspend if it is wake up source.
Enable wakeup event during suspend.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current code missed disabling interrupts before free irq which is shared.
Notice below comments for function free_irq (kernel/irq/manage.c):
On a shared IRQ the caller must ensure the interrupt is disabled
on the card it drives before calling this function.
Original code has below issue during suspend/resume when multiple SD
hosts share the same IRQ:
1. Assume there are two hosts (host1 for emmc while host2 for sd) share
the same mmc irq.
2. When system suspend, host2 will be suspended before host1.
So the sequence is below:
step1: irq handler for host2 removed ->
step2: irq handler for host1 removed and irq disabled ->
... system suspended ...
... system resumed ...
step3: irq enabled and the irq handler for host1 restored ->
step4: irq handler for host2 restored
3. So there is the buggy time slot that the irq is enabled but the irq
handler for host2 is removed. Then host2 interrupt can be triggered
but can't be handled at that moment.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call mmc_gpio_get_cd() to query card presence from cd-gpio before
asking SDHCI. The rationale behind this change is that flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is designed for SDHCI controller to
tell that SDHCI_PRESENT_STATE is broken, and it should be used for this
case only. So when cd-gpio is being used, the controller should set
the flag to tell that SDHCI_PRESENT_STATE is not available.
However, the existing code will skip checking cd-gpio as long as flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is set. Change the querying order
between cd-gpio and SDHCI to support the rationale above.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Extracting a part of the SDHCI card tasklet into a .card_event()
implementation allows SDHCI hosts to use generic card-detection
services, e.g. the GPIO slot function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available.
Add a quirk so that systems such as this one can override disable
1.8v support, adding support for UHS-I cards (by running them at
3.3v).
This avoids a problem where the system would first try to run the
card at 1.8v, fail, and then not be able to fully reset the card
to retry at the normal 3.3v voltage.
This is more appropriate than using the MISSING_CAPS quirk, which
is intended for cases where the SDHCI controller is actually lying
about its capabilities, and would force us to somehow override both
caps words from another source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For regulator vmmc/vmmcq, use voltage range as below
3.3v/3.0v: (2.7v, 3.6v)
1.8v: (1.7v, 1.95v)
Original code uses the precise value which may fail in regulator
driver if it does NOT support the precise voltage.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 473b095a72 ("mmc: sdhci: fix incorrect command used in tuning")
introduced a NULL dereference at resume-time if an SD 3.0 host controller
raises the SDHCI_NEEDS_TUNING flag while no card is inserted. Seen on an
OLPC XO-4 with sdhci-pxav3, but presumably affects other controllers too.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable <stable@vger.kernel.org> [3.3+]
There are two problems here:
The check for vmmc was printing an unnecessary pr_info() when
host->vmmc is NULL.
The intent of the check for vqmmc was to only remove UHS if we have a
regulator that doesn't support the required voltage, but since IS_ERR()
doesn't catch NULL, we were actually removing UHS modes if vqmmc isn't
present at all -- since it isn't present for most users, this breaks
UHS for them. This patch fixes that UHS regression in 3.7-rc1.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Bin Wang <binw@marvell.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.
The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.
A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously to this patch, an SDHCI platform that uses a GPIO for
card detection instead of the internal SDHCI_CARD_PRESENT bit on
the presence register would fail to detect a new card.
Some drivers worked around this in various ways: esdhc-imx defines
an IO accessor to fake the presence bit being true, s3c turns on
polling (which stops the SDHCI driver from checking the bit) after
a card's inserted. But none of this should be necessary; the real
fix is to check whether we're using a GPIO and avoid relying on
the presence bit if so, as this patch implements.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The vmmc regulator should not rely on the platform code to enable it.
Expliciitly enable and disable the regulator inside the driver.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some systems the host controller does not support vccq
signaling. This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host has different current capabilities at different voltages, we need
to record these settings seperately. The defined voltages are 1.8/3.0/3.3.
For other voltages, we do not touch current limit setting.
Before we set the current limit for the sd card, find out the host's
operating voltage first and then find out the current capabilities of
the host at that voltage to set the current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Power needs to be removed from the card when switching to 1.8v fails.
If a regulator is used to control vmmc we need to turn the
regulator off and then back on otherwise power will not be
removed from the card.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Marvell CaFe is now marked as having bad card detection to fix
a problem during system resume.
Now on the OLPC XO-1 we are facing the issue that the card is marked
as logically unremovable (via MMC_UNSAFE_RESUME), which means that
mmc_card_is_removable considers the card non-removable. The existing
code logic decides not to poll for card presence in this case, and
card detection is also disabled because of the quirk being set.
This means that no SD cards are detected when inserted after boot.
Refine the logic to enable card presence polling in the case when
a card is logically unremovable, only avoiding the poll in the case
when the card is physically non-removable (denoted with
MMC_CAP_NONREMOVABLE).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host
is using a retuning timer for the card inserted.
This flag is set when the host does tuning the first time for the card
and the host's retuning mode is 1. This flag is used afterwards whenever
needs to decide if the host is currently using a retuning timer.
This flag is cleared when the card is removed in sdhci_reinit.
The set/clear of the flag and the start/stop of the retuning timer is
associated with the card's init/remove time, so there is no need to
touch it when the host is to be removed as at that time the card should
have already been removed.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some of the host settings are affected by different cards inserted, e.g.
when an UHS-I card is inserted, the SDHCI_NEEDS_RETUING flag might be
set when the tuning timer expired and host's max_blk_count will be
reduced to make sure the data transfer for a command does not exceed 4MiB
to meet the retuning mode 1's requirement.
When the card is removed, we should restore the original setting of the
host since we can't be sure the next card being inserted will still be
an UHS-I card that needs tuning. The original setting include its
max_blk_count and no set of the flag of SDHCI_NEEDS_RETUNING.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For SD hosts using retuning mode 1, when retuning timer expired, it will
need to do retuning in sdhci_request before processing the actual
request. But the retuning command is fixed: cmd19 for SD card and cmd21
for eMMC card, so we can't use the original request's command to do the
tuning.
And since the tuning command depends on the card type attached to the
host, we will need to know the card type to use the correct tuning
command.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Cc: stable <stable@vger.kernel.org> [3.3+]
Signed-off-by: Chris Ball <cjb@laptop.org>
For most error conditions sdhci_add_host() will print a diagnostic
message indicating why it failed but there are a few cases where this
does not happen. Add error messages in these cases to aid diagnosis.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently only the capability_0 register can be set if
SDHCI_QUIRK_MISSING_CAPS is defined. This is a problem when
the capability_1 register also needs changing. Use the quirk
SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set.
Redefining caps[1] is useful when the board design does not
support 1.8v vccq so UHS modes are not available. The code that
calls sdhci_add_host can then detect this condition and adjust
the caps so the UHS mode will not be attempted on UHS cards.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we are using a regulator the SD Host Controller and the
regulator should agree about the voltages supported. Use
the common subset that is supported.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sd host controller spec indicates the the MAX_CURRENT value may
be returned as 0. In this case other methods need to be used to
return the current. If 0 is returned and there is a regulator,
ask the regulator for how much current is available.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
3bdc9ba892 ("mmc: use really long write timeout to deal with crappy
cards") in 3.4 increased the write timeout that the core sends to host
drivers to 3 seconds. This makes sdhci's "requested timeout too large"
warning trigger on every write; so, change this pr_warning() to a DBG().
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rather than just logging that we came up with an excessively large timeout
say what the timeout was, this may provide some clues as to what the issue
is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit c79396c191 ("mmc: sdhci: prevent card detection activity
for non-removable cards") disables card detection where the cards
are marked as non-removable.
This makes sense, but the implementation detail of calling
mmc_card_is_removable() causes some problems, because
mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME
semantics.
In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root
filesystem is stored on SD, but we also have external SD card slots
where we want automatic card detection.
Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE,
which is defined to mean that the card is *really* nonremovable. This
could be revisited in future if we find a way to improve
CONFIG_MMC_UNSAFE_RESUME semantics.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
[stable@: please apply to 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using MSI it is possible that a new MSI is sent while an earlier
MSI is currently handled. In this case SDHCI_INT_STATUS only contains
SDHCI_INT_RESPONSE and the ISR would not be called again. But at the end
of the ISR SDHCI_INT_DATA_END is now also pending which would be ignored.
Fix this by rereading the interrupt flags in the ISR until no interrupt
we care is pending.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add quirk SDHCI_QUIRK2_HOST_OFF_CARD_ON to cater for the case when the
card keeps power during suspend but the host controller does not i.e.
the card power is not controlled by the host controller. In that
case, the controller must be fully reset on resume.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms require saving/restoring registers across suspend/resume;
this hook allows them to do that inside their driver.
Signed-off-by: Chris Ball <cjb@laptop.org>
If dma is enabled, it'll be cleared when reset all is performed, this can
be observed on some platforms, such as P2041 which has a version 2.3
controller, but platform like P4080 which has a version 2.2 controller,
does not suffer this, so we will check if the dma is enabled, we should
restore it after reset all.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there are errors happened in sdhci_suspend_host, handle it so that
when the function returns with an error, the host's behaviour is the
same before this function call, e.g. card detection is enabled and
tuning timer is active, etc.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader. Patch 49c468f ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: Alexander Elbs <alex@segv.de>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When suspending host, the tuning timer shoule be deactivated.
And the HOST_NEEDS_TUNING flag should be set after tuning timer is
deactivated.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
To allow the set_clock host op to disable the SDCLK source when not
needed, always call the host op when the requested clock speed is
zero. Do this even if host->clock already equals zero, because
the SDHCI driver may set that value (without calling the host op)
to force an update at the next (non-zero-speed) call.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not enable card detection interrupts for non-removable cards.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Presently the vmmc regulator is enabled when the host
controller is added and disabled when it is removed.
However, the vmmc regulator should be under the control
of the upper layers via ->set_ios(). Make it so.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.
For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios. Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Drop the "state" argument from sdhci_suspend_host. Its only user is the
PCI glue; this allows to move all SDHCI glues to use dev_pm_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed. During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.
For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an SDHCI operation for hardware reset and connect it to the
host controller operation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In general, SDHC hardware timeout cannot be avoided.
Accordingly, the maximum timeout is specified to limit
the maximum discard size.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The issue was initially found by Eric Benard as below.
http://permalink.gmane.org/gmane.linux.ports.arm.kernel/108031
Not sure about other SDHCI based controller, but on Freescale eSDHC,
the SDHCI_INT_CARD_INSERT bits will be immediately set again when it
gets cleared, if a card is inserted. The driver need to mask the irq
to prevent interrupt storm which will freeze the system. And the
SDHCI_INT_CARD_REMOVE gets the same situation.
The patch fixes the problem based on the initial idea from
Eric Benard.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Benard <eric@eukrea.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enables Auto-CMD23 support where available (SDHCI 3.0 controllers)
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Tested-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow platform specific code to set UHS registers if
implementation requires speciial platform specific handling
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 can support retuning modes 1,2 or 3 depending on
the bits 46-47 of the Capabilities register. Also, the timer count for
retuning is indicated by bits 40-43 of the same register. We initialize
timer_list for retuning the first time we execute tuning procedure. This
condition is indicated by SDHCI_NEEDS_RETUNING not being set. Since
retuning mode 1 sets a limit of 4MB on the maximum data length, we set
max_blk_count appropriately. Once the tuning timer expires, we set
SDHCI_NEEDS_RETUNING flag, and if the flag is set, we execute tuning
procedure before sending the next command. We need to restore mmc_request
structure after executing retuning procedure since host->mrq is used
inside the procedure to send CMD19. We also disable and re-enable this
flag during suspend and resume respectively, as per the spec v3.00.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 supports programmable clock mode as an optional
feature. The support for this mode is indicated by non-zero value in
bits 48-55 of the Capabilities register. If supported, the actual
value of Clock Multiplier is one more than the value provided in the
bit fields. We only set Clock Generator Select (bit 5) and SDCLK
Frequency Select (bits 8-15) of the Clock Control register in case
Preset Value Enable is not set, otherwise these fields are automatically
set by the Host Controller based on the UHS mode selected. Also, since
the maximum and minimum clock frequency in this mode can be
(Base Clock * Clock Mul) and (Base Clock * Clock Mul)/1024 respectively,
f_max and f_min have been recalculated to reflect this change.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the Host Controller spec v3.00, setting Preset Value Enable
in the Host Control2 register lets SDCLK Frequency Select, Clock Generator
Select and Driver Strength Select to be set automatically by the Host
Controller based on the UHS-I mode set. This patch enables this feature.
Since Preset Value Enable makes sense only for UHS-I cards, we enable this
feature after successfull UHS-I initialization. We also reset Preset Value
Enable next time before initialization.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.
We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We decide on the current limit to be set for the card based on the
Capability of Host Controller to provide current at 1.8V signalling,
and the maximum current limit of the card as indicated by CMD6
mode 0. We then set the current limit for the card using CMD6 mode 1.
As per the Physical Layer Spec v3.01, the current limit switch is
only applicable for SDR50, SDR104, and DDR50 bus speed modes. For
other UHS-I modes, we set the default current limit of 200mA.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per Host Controller spec v3.00, we reset SDCLK before setting
High Speed Enable, and then set it back to avoid generating clock
gliches. Before enabling SDCLK again, we make sure the clock is
stable, so we use sdhci_set_clock().
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On HP laptops with JMicron 388 chip, the write-locked SD card isn't
detected correctly as read-only in many cases. This is because the
PRESENT_STATE register becomes unsable just after plugging, and it
returns the WRITE_PROTECT bit wrongly at the first read.
This patch fixes the read-only detection by adding a new sdhci quirk
indicating to check the register more intensively with a relatively
long delay.
The patch is tested with 2.6.39-rc4 kernel.
Cc: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Marvell pxa controllers have private registers that may need to be
modified before and after a reset is done.
For example, the SD reset operation, RESET_ALL, will reset the private
registers to their default state. This will cause the clock adjustment
registers that may have been programmed to have incorrect values.
RESET_DATA sometimes needs to be delayed before the reset is done
(depending on SoC) to enable any transactions being handled by the
SDIO card to be completed. Needed in pre SD 3.0 silicon to handle
clock gating.
Implement hooks to allow this to happen.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 373e6a (mmc: sdhci: R1B command handling + MMC_CAP_ERASE) moved the
handling of SDHCI_QUIRK_TIMEOUT_USES_SDCLK from sdhci_calc_timeout() to
sdhci_add_host(). This causes division by zero errors on at least the S3C
SDHCI controller as the quirk implementation needs host->clock set to work
but host->clock has not been set when sdhci_add_host() is called.
Fix this by backing out that portion of the change, the clock may vary at
runtime anyway. It does occur to me that we may want to move the quirk to
where we set the clock but this seems more invasive and I'm concerned
about undesirable side effects.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SD host controllers (noticed on an integrated JMicron SD reader on an
HP Pavilion dv5-1250eo laptop) don't update the dma address register before
signaling a dma interrupt due to a dma boundary. Update the register
manually to the next boundary (by default 512KiB), at which the transfer
stopped.
As long as each transfer is at most 512KiB in size (guaranteed by a BUG_ON
in sdhci_prepare_data()) and the boundary is kept at the default value,
this fix is needed at most once per transfer. Smaller boundaries are taken
care of by counting the transferred bytes.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=28462
Signed-off-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ERASE command needs R1B response, so fix R1B-type command
handling for SDHCI controller. For non-DAT commands using a busy
response, the cmd->cmd_timeout_ms (in ms) field is used for timeout
calculations.
Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It seems that under certain circumstances the sdhci_tasklet_finish()
call can be entered with mrq set to NULL, causing the system to crash
with a NULL pointer de-reference.
Seen on S3C6410 system. Based on a patch by Dimitris Papastamos.
Reported-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It seems that under certain circumstances that the sdhci_tasklet_finish()
call can be entered with mrq->cmd set to NULL, causing the system to crash
with a NULL pointer de-reference.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at sdhci_tasklet_finish+0x34/0xe8
LR is at sdhci_tasklet_finish+0x24/0xe8
Seen on S3C6410 system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers misparse segment length 0 as being 0, not 65536. Add
a quirk to deal with it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively. This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.
[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
JMicron 388 SD/MMC combo controller supports the 1.8V low-voltage for
SD, but MMC doesn't work with the low-voltage, resulting in an error
at probing.
This patch adds the support for multiple voltage mask per device type,
so that SD works with 1.8V while MMC forces 3.3V. Here new ocr_avail_*
fields for each device are introduced, so that the actual OCR mask is
switched dynamically.
Also, the restriction of low-voltage in core/sd.c is removed when the
bit is allowed explicitly via ocr_avail_sd mask.
This patch was rewritten from scratch based on Aries' original code.
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
More information should be shown when sdhci_dumpregs is called.
Knowing the command is useful for debugging, and Capability 1
is useful for SD v3.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A little more work was needed for SDIO IRQ wakeups to be functional.
Wake-on-WLAN on the SD WiFi adapter in the XO-1.5 laptop is now working.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers handle their write-protection differently. Introduce a
callback to be able to handle it, ensuring the same locking takes place
for it. Rename the status variable to make it more obvious why the read
from the registers needs to be inverted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Snippet of code for how adaptation layer should handle the call:
/*
* eMMC spec calls for the host to send 74 clocks to the card
* during initialization, right after voltage stabilization.
* create the clocks manually right here.
*/
void generate_init_clocks_A0(struct sdhci_host *host, u8 power_mode)
{
struct sdhci_mmc_slot *slot = sdhci_priv(host);
if (slot->power_mode == MMC_POWER_UP &&
power_mode == MMC_POWER_ON) {
/* controller specific code here */
/* slot->power_mode holds previous power setting */
}
slot->power_mode = power_mode;
}
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SD and MMC code set highspeed using different constants.
Change the sd driver to recognize this and switch to high speed.
Validated code when testing eMMC dual data rate.
Signed-off-by: Philip Rakity <prakity@marvell.com>
[cjb: changelog + indentation fixes]
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a warning when compiling the sdhci driver:
pwr may be used uninitialized in sdhci_set_power
Tested with the following compiler versions: 4.2.4 and 4.4.4
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a controller requires SDHCI_QUIRK_BROKEN_CARD_DETECTION, we poll
for card insertion/removal, and that creates interrupts. There's no
need to be doing this if we have a non-removable card.
This patch requires cards to be removable before we're willing to set
MMC_CAP_NEEDS_POLL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[cjb: modified changelog and code indentation]
Signed-off-by: Chris Ball <cjb@laptop.org>
In a multi-controller environment it is helpful to know which controller
has problems.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is necessary to gain the performance boost from 8-bit data
with the sdhci-stm driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP_MMC_HIGHSPEED allows MMC and eMMC to negotiate up to 50M
instead of the previous limit of 25M.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
While we're at it, add symbols for SDHCI_MAX_DIV_SPEC_{200,300}.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHC Spec 3.0: Capabilities Register bits[15-08] are Base Clock Frequency
1.0/2.0: Capabilities Register bits[13-08] are Base Clock Frequency
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Michal Miroslaw <mirqus@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "6882a8c sdhci: Add better ADMA error reporting" commit added
sdhci_show_adma_error() which is built when DEBUG is defined. Since we
already have CONFIG_MMC_DEBUG used elsewhere in this driver, may as well
make consistent use of that config knob instead.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SDHCI controllers like s5pc110 don't have an HISPD bit in the HOSTCTL
register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add auto CMD12 command support for eSDHC driver. This is needed by P4080
and P1022 for block read/write. Manual asynchronous CMD12 abort operation
causes protocol violations on these silicons.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for regulator API to sdhci core driver.
Regulators can be used to disable power in suspended state to reduce
dissipated energy.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C SDHCI host controller can change the source for generating mmc clock.
By default host bus clock is used, what causes some problems on machines
with 133MHz bus, because the SDHCI divider cannot be as high get proper
clock value for identification mode. This is not a problem for the
controller, because it can generate lower frequencies from other clock
sources. This patch changes sdhci driver to use get_min_clock() call if
it has been provided.
This fixes the flood of the following warnings on Samsung S5PV210 SoCs:
mmc0: Minimum clock frequency too high for identification mode
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some host controllers can set mmc->caps before sdhci_add_host().
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some host controllers such as s5pc110 support the WIDE8 feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using QUIRK_NONSTANDARD_CLOCK, it checks the set_clock() function
which is not used actually. So delete it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current way of disabling it is not well tested by vendor and has all
kinds of bugs that show up on resume from ram/disk. A very good example
is a dead SDHCI controller.
Old way of disabling is still supported by continuing to use
CONFIG_MMC_RICOH_MMC.
Based on 'http://list.drzeus.cx/pipermail/sdhci-devel/2007-December/002085.html'
Therefore most of the credit for this goes to Andrew de Quincey
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Philip Langdale <philipl@overt.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core. As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.
We might as well just delete the unused paramter.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s3c6410 sdhci controller does not support the 'End' attribute and NOP
attribute in the same 8-Byte ADMA descriptor. This patch adds a new quirk
to identify sdhci host contollers with such behaviour. In addition to
this, for controllers using the new quirk, the last entry in the ADMA
descritor table is marked with the 'End' attribute (instead of using a NOP
descriptor with 'End' attribute).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hosts (e.g. as found in CNS3xxx SOCs) report wrong value in
CLOCK_BASE capability field, and currently there is no way to force the
SDHCI core to use the platform-provided base clock value.
This patch implements CAP_CLOCK_BASE_BROKEN quirk. When enabled, the
SDHCI core will always use base clock frequency provided by the platform.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Tested with an XO v1.5 from OLPC.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory. Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.
This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.
As an example on ARM S3C64XX SoC, in little-endian configuration:
000000d4 <sdhci_set_adma_desc>:
- d8: e1a0c423 lsr ip, r3, #8
- dc: e1a0ec21 lsr lr, r1, #24
- e0: e1a04821 lsr r4, r1, #16
- e4: e1a05421 lsr r5, r1, #8
- e8: e1a06442 asr r6, r2, #8
- ec: e5c0c001 strb ip, [r0, #1]
- f0: e5c0e007 strb lr, [r0, #7]
- f4: e5c04006 strb r4, [r0, #6]
- f8: e5c05005 strb r5, [r0, #5]
- fc: e5c01004 strb r1, [r0, #4]
- 100: e5c06003 strb r6, [r0, #3]
- 104: e5c02002 strb r2, [r0, #2]
- 108: e5c03000 strb r3, [r0]
+ d4: e5801004 str r1, [r0, #4]
+ d8: e1c030b0 strh r3, [r0]
+ dc: e1c020b2 strh r2, [r0, #2]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function. This will also be useful if the patch to make the write
more efficient is accepted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On an OLPC XO-1.5 development board with Via VX855 chipset, the sdhci
controller can take up to 12ms to stabilize its clock, but the current
timeout at which we give up on the controller is 10ms.
The patch increases the timeout delay rather than using a device-specific
quirk -- since we exit the loop when the clock comes up, increasing the
timeout value will only make us mdelay() longer in the errant case of a
device with a clock that is not stabilizing, which it seems worth waiting
a little longer for in general.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for ADMA on SDHCI hosts, not supporting SDMA.
According to the SDHCI specifications a host can support ADMA but not SDMA
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eSDHC fails to recognize some SDHS cards, throwing timeout errors:
mmc0: error -110 whilst initialising SD card
That's because we calculate timeout value in a wrong way: on eSDHC hosts
the timeout clock is derivied from the SD clock, which is set dynamically.
As David Vrabel suggested, deriving timeout clock from SD clock is a
common scheme, so let's implement DATA_TIMEOUT_USES_SDCLK quirk and use it
for eSDHC hosts.
Also, from now on we don't need esdhc_get_timeout_clock() callback, so
remove it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_min_clock() makes sense only with NONSTANDARD_CLOCK quirk and when
set_clock() callback is specified.
The patch should cause no functional changes, it just makes the code
self-documented and avoids any possible misuse of get_min_clock().
Suggested-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
so the page will be flushed on unmap on ARCH which need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Since commit 8dfd0374be ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:
...
mmc0: Minimum clock frequency too high for identification mode
mmc0: Minimum clock frequency too high for identification mode
...
The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.
But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.
This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SDHCI controller found in the VX855ES requires 10ms
delay between applying power and applying clock.
This issue has been discovered and documented by the OLPC XO1.5 team.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some hosts (hardware configurations, or particular SD/MMC slots) may
not support 4-bit bus. For example, on MPC8569E-MDS boards we can
switch between serial (1-bit only) and nibble (4-bit) modes, thought
we have to disable more peripherals to work in 4-bit mode.
Along with some small core changes, this patch modifies sdhci-of
driver, so that now it looks for "sdhci,1-bit-only" property in the
device-tree, and if specified we enable a proper quirk.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Add quirk to show the controller cannot do multi-block IO.
This is mainly for the Samsung SDHCI controller that currently
cannot manage to do multi-block PIO without timing out.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Update the ADMA error reporting to not only show the
overall controller state but also to print the ADMA
descriptor list.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.
But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.
Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.
[1] http://lkml.org/lkml/2008/12/2/160
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.
p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.
p.s. Actually, the quirk is more board-specific than
controller-specific.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.
This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.
sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().
New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().
Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:
- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant
sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the led device naming for the sdhci driver.
The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.
To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This reverts commit a4b7619377.
It turned out that the controller had problem running at the
higher speed, so go back to trusting the hardware capability
bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As reported by Randy Dunlap, having sdhci built-in and LEDs class
as a module resulted in undefined symbols. Change the code to handle
that case properly (by not having LEDs class support in sdhci).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The variable 'scratch' is always initialized before it's used. The
conditional which is responsible for initialization of 'scratch' will
always evaluate 'true' when the first loop iteration occurs, and thus,
it's properly initialized. GCC doesn't see this, of course, so using
the uninitialized_var() macro seems to work for silencing this case.
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some high speed capable controllers forget to set the high speed
capability bit. Make sure we enable the functionality anyway.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The card detection delay was added early when the behaviour of the
card interrupt was still very much unknown (i.e. before there was a
public specification). As it is now known that it is a debounced signal,
reduce the delay to something more sensible.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The sdhci controllers can interrupt us when the busy state from the
card has ended, saving CPU cycles and power.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wrong flag was manipulated when an invalid sg list was given, turning
off DMA on the next (and all subsequent) request instead of the current
one.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8b3e02 renamed a variable, but missed one reference to it
inside a WARN_ON, causing it to incorrectly trigger.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The ADMA code path assumes that the 3 byte alignment fix doesn't cross
a page boundary. I'm not convinced this is worth supporting, but at
least print a warning in the off chance we'll actually see such a request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This comment update got lost in the great floo^Wmerge. As Pierre
pointed out, no one knows what 'CaFe' is.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.
Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.
This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The specification is insufficiently strict when it comes to how the
hardware should update the block count register, making it useless
for checking transfer progress.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Even the newer ENE controllers have bugs in their DMA engine that make
it too dangerous to use. Disable it until someone has figured out under
which conditions it corrupts data.
This has caused problems at least once, and can be found as bug report
10925 in the kernel bugzilla.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CaFe chip has a hardware bug that ends up with us getting a timeout
value that's too small, causing the following sorts of problems:
[ 60.525138] mmcblk0: error -110 transferring data
[ 60.531477] end_request: I/O error, dev mmcblk0, sector 1484353
[ 60.533371] Buffer I/O error on device mmcblk0p2, logical block 181632
[ 60.533371] lost page write due to I/O error on mmcblk0p2
Presumably this is an off-by-one error in the hardware. Incrementing
the timeout count value that we stuff into the TIMEOUT_CONTROL register
gets us a value that works. This bug was originally discovered by
Pierre Ossman, I believe.
[thanks to Robert Millan for proving that this was still a problem]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been sitting around unloved for way too long..
The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write. This adds a quirk that does
that particular dance in two steps.
It also adds an entry to pci_ids.h for the CaFe chip's SD device.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The quirk was meant to just inhibit some resets, but ended up blocking
all of them. Fortunately, this was just what was needed. Change the
comment to reflect reality.
Also, this issue has just been observed on Samsung laptops, so reduce
the number of chips the quirk affects.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Do a full scan of the directory to try and be a bit more proactive,
instead of waiting for things to break.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The forcedma and nodma module parameters can be replaced with the quirks
parameter, so remove the redundancy.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers like ENE712 can't work properly with DMA mode,
add this quirk to force these kinds of HW work with PIO mode
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Many host controllers don't fully follow the PCI spec to claim
whether they support DMA in PCI class register. Leave the driver
to judge it from the Capability register, quirks and module parameter
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some SDHC cards report an invalid maximum block size, in these cases
assume they support block sizes up to 512 bytes instead of returning
an error.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The block count register shouldn't be trusted for single block transfers,
so avoid using it completely when calculating transferred bytes.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Added its pci_id and implemented a quirk for it because this
controller needs to reset cmd and data when setting ios.
Signed-off-by: Leandro Dorileo <dorileo@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers signal "command complete" even on failures (which
they are allowed to do according to the spec). Make sure we check
the error bits first so we don't get any false positives.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The controller has a bit indicating that one of the higher bits (the
error bits) are set. A previous bug caused this bit to be masked, but
since that bug has been fixed we have to clear it explicictly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Whenever a power interrupt is signaled it is also reported as an unexpected
one. All other unexpected interrupts get lost. Cause is a not inversed
bitmask to remove power interrupts from the status.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
ENE has a very weird design where an SDHCI device (0805) is presented
on the PCI bus, but that device is non-functional, and the real device
is hidden as a more generic device.
Signed-off-by: Milko Krachounov <milko@3mhz.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix handling of low voltage MMC cards.
The latest MMC and SD specs both agree that support for
low-voltage operations is indicated by bit 7 in the OCR.
The MMC spec states that the low voltage range is
1.65-1.95V while the SD spec leaves the actual voltage
range undefined - meaning that there is still no such
thing as a low voltage SD card.
However, an old Sandisk spec implied that bits 7.0
represented voltages below 2.0V in 1V or 0.5V increments,
and the code was accordingly written with that expectation.
This confusion meant that host drivers attempting to support
the typical low voltage (1.8V) would set the wrong bits in
the host OCR mask (usually bits 5 and/or 6) resulting in the
the low voltage mode never being used.
This change corrects the low voltage range and adds sanity
checks on the reserved bits (0-6) and for SD cards that
claim to support low-voltage operations.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Consolidate the list of available voltages.
Up until now, a separate set of defines has been
used for host->vdd than that used for the OCR
voltage mask values. Having two sets of defines
allows them to get out of sync and the current
sets are already inconsistent with one claiming
to describe ranges and the other specific voltages.
Only the SDHCI driver uses the host->vdd defines and
it is easily fixed to use the OCR defines.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
