With gcc-4.1.2:
mmc/core/block.c: In function ‘mmc_blk_issue_discard_rq’:
mmc/core/block.c:1150: warning: ‘arg’ may be used uninitialized in this function
mmc/core/block.c:1150: warning: ‘nr’ may be used uninitialized in this function
mmc/core/block.c:1150: warning: ‘from’ may be used uninitialized in this function
While this is a false positive, it can be avoided easily by jumping over
the checks for "err" that are always false.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the eMMC 5.0 version of the spec, several EXT_CSD fields about
device lifetime are added.
- Two types of estimated indications reflected by averaged wear out of memory
- An indication reflected by average reserved blocks
Export the information through sysfs.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setup tuning when the board is HS200 enabled.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The capability for HW_RESET is only activated if SDR104 is present, so
no need to check for SDR104 in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Prerequisites for tuning are the same as for hw_reset. We need an SCC
and a supported mode. Populate the tuning related functions only when
those conditions are met. This also removes a tiny race window.
Previously, the functions were populated when the SCC offset was not
initialized which could have led to an OOPS.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need a SCC unit for hw_reset. Those units can only be described in
of_data. So, of_data and a valid SCC offset are prerequisites for
enabling the hw_reset capability. Merge the two 'if' conditions into one
and add a check for an scc offset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By using the helper of_device_get_match_data(), we can skip some
checking and make the code simpler.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The master bit to enable SDIO interrupts can only be accessed if
SCLKDIVEN bit allows that. However, the core uses the SDIO enable
callback at times when SCLKDIVEN forbids the change. This leads to
"timeout waiting for SD bus idle" messages.
We now activate the master bit in probe once if SDIO is supported. IRQ
en-/disabling will be done now by the individual IRQ enablement bits
only.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.
A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches. Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete. As a result, mmcqd task
may be stuck forever.
Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:
..
[ 240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[ 240.257973] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.270955] mmcqd/1 D c047504c 0 52 2 0x00000000
[ 240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[ 240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[ 240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[ 240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[ 240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[ 240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[ 240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[ 240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[ 240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[ 240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[ 240.670943] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.683922] partprobe D c047504c 0 564 486 0x00000000
[ 240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[ 240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[ 240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[ 240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[ 240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..
Here is the detailed sequence showing when this issue may happen:
1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.
2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).
3) Then mmci interrupt is raised and mmci_irq() is called:
MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.
Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.
Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.
Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case. And we finally go
through following test at the end of while(status) loop:
/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;
Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:
a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is equal to 0x010003FF:
b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.
Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.
Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.
Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.
To fix the problem, this patch implements the following changes:
Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.
1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.
This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.
Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices. This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.
This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: <stable@vger.kernel.org>
It's necessary to setup bus if any slots are present.
- update clock after ctrl reset
- if the host has genpd node, we can guarantee the clock is
available before starting request. Otherwies, the clock register
is reset once power off the pd, and host can't output the active
clock during communication.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Fixes: df9bcc2bc0 ("mmc: dw_mmc: add missing codes for runtime resume")
cc: <stable@vger.kernel.org>
Reported-by: Randy Li <randy.li@rock-chips.com>
Reported-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.
The commit e173f8911f ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.
To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.
In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Gary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f8911f ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
According to the code the intention is to append 8 SCK cycles
instead of 4 at end of a MMC_STOP_TRANSMISSION command. But this
will never happened because it's an AC command not an ADTC command.
So fix this by moving the statement into the right function.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are
powered when probing") introduced code to powerup any acpi child
nodes listed in the dstd. But some dstd-s list all possible devices
used on some board variants, while reporting if the device is actually
present and enabled in the status field of the device.
So we end up calling the acpi _PS0 (power-on) method for devices which
are not actually present. This does not always end well, e.g. on my
cube iwork8 air tablet, this results in freezing the entire tablet as
soon as the r8723bs module is loaded.
This commit fixes this by checking the child device's status.present
and status.enabled bits and only call acpi_device_fix_up_power()
if both are set.
Fixes: e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are powered when probing")
BugLink: https://github.com/hadess/rtl8723bs/issues/80
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No actual segmentation faults were observed but the coding is
at least inconsistent.
irqreturn_t meson_mmc_irq():
We should not dereference host before checking it.
meson_mmc_irq_thread():
If cmd or mrq are NULL we should not dereference them after
writing a warning.
Fixes: 51c5d8447b MMC: meson: initial support for GX platforms
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mmc_read_ssr() function results in DMA to the raw_ssr member of
struct mmc_card, which is not guaranteed to be cache line aligned & thus
might not meet the requirements set out in Documentation/DMA-API.txt:
Warnings: Memory coherency operates at a granularity called the cache
line width. In order for memory mapped by this API to operate
correctly, the mapped region must begin exactly on a cache line
boundary and end exactly on one (to prevent two separately mapped
regions from sharing a single cache line). Since the cache line size
may not be known at compile time, the API will not enforce this
requirement. Therefore, it is recommended that driver writers who
don't take special care to determine the cache line size at run time
only map virtual regions that begin and end on page boundaries (which
are guaranteed also to be cache line boundaries).
On some systems where DMA is non-coherent this can lead to us losing
data that shares cache lines with the raw_ssr array.
Fix this by kmalloc'ing a temporary buffer to perform DMA into. kmalloc
will ensure the buffer is suitably aligned, allowing the DMA to be
performed without any loss of data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 5275a652d2 ("mmc: sd: Export SD Status via “ssr” device attribute")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e0097cf5f2 ("mmc: queue: Fix queue thread wake-up") did not go far
enough. mmc_wait_for_data_req_done() still contains some problems and can
be further simplified. First it should not touch
context_info->is_waiting_last_req because that is a wake-up control used by
the owner of the context. Secondly, it should always return when one of its
wake-up conditions is met because, again, that is contolled by the owner of
the context.
While the current block driver does not have an issue, these problems were
exposed during testing of the Software Command Queue patches.
Fixes: e0097cf5f2 ("mmc: queue: Fix queue thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit c2c24819b2 ("mmc: core: Don't power off the card when
starting the host"), the power state can still be MMC_POWER_UNDEFINED after
mmc_start_host() is called. That can trigger a warning in SDHCI during
runtime resume as it tries to restore the I/O state. Handle
MMC_POWER_UNDEFINED simply by not updating the I/O state in that case.
Fixes: c2c24819b2 ("mmc: core: Don't power off the card when starting the host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a Socionext SoC specific compatible (suggested by Rob Herring).
No SoC specific data are associated with the compatible strings for
now, but other SoC vendors may use this IP and want to differentiate
IP variants in the future.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Move files from the card directory to the core directory to enable
future clean-ups of the generic mmc header files and interfaces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U2+h
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull another MMC update from Ulf Hansson:
"Here's a second pull request for MMC for v4.10.
As a matter of fact it's only one change that moves some mmc files
around. I thought it was a good idea to get this into v4.10, as it
gives us a nice and fresh base for v4.11. Summary:
MMC core:
- Move files from the card directory to the core directory to enable
future clean-ups of the generic mmc header files and interfaces"
* tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: Move files to core
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Once upon a time it made sense to keep the mmc block device driver and its
related code, in its own directory called card. Over time, more an more
functions/structures have become shared through generic mmc header files,
between the core and the card directory. In other words, the relationship
between them has become closer.
By sharing functions/structures via generic header files, it becomes easy
for outside users to abuse them. In a way to avoid that from happen, let's
move the files from card directory into the core directory, as it enables
us to move definitions of functions/structures into mmc core specific
header files.
Note, this is only the first step in providing a cleaner mmc interface for
outside users. Following changes will do the actual cleanup, as that is not
part of this change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.
Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.
This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy the tuning loop by moving it to a separate function and making it a
for-loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are only 2 possible block sizes, so simplify 2 if-statements into 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out some functions to tidy up the code in sdhci_execute_tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use mmc_abort_tuning() instead of open-coding the stop command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").
A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JEDEC specification indicates CMD13 can be used after a HS200 switch
to check for errors. However in practice some boards experience CRC errors
in the CMD13 response. Consequently, for HS200, CRC errors are not a
reliable way to know the switch failed. If there really is a problem, we
would expect tuning will fail and the result ends up the same. So change
the error condition to ignore CRC errors in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is unnecessary to panic the kernel when testing mmc. Instead,
cast a warning for folkz to debug and return the error code to
the caller to indicate the failure of this test should be enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bounce_sg for mqrq_cur and mqrq_pre are proper
allocated when initializing the queue and will not
be freed before explicitly cleaning the queue. So from
the code itself it should be quite confident to remove
this check. If that BUG_ON take effects, it is mostly
likely the memory is randomly oopsing.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>