Add reset assertion/deassertion for Aspeed MDIO. There are 4 MDIO
controllers embedded in Aspeed AST2600 SOC and share one reset control
register SCU50[3]. To work with old DT blobs which don't have the reset
property, devm_reset_control_get_optional_shared is used in this change.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Create a local device *dev in order to not dereference the platform_device
several times throughout the probe function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a driver for an interrupt controller is missing, of_irq_get()
returns -EPROBE_DEFER ad infinitum, causing
fwnode_mdiobus_phy_device_register(), and ultimately, the entire
of_mdiobus_register() call, to fail. In turn, any phy_connect() call
towards a PHY on this MDIO bus will also fail.
This is not what is expected to happen, because the PHY library falls
back to poll mode when of_irq_get() returns a hard error code, and the
MDIO bus, PHY and attached Ethernet controller work fine, albeit
suboptimally, when the PHY library polls for link status. However,
-EPROBE_DEFER has special handling given the assumption that at some
point probe deferral will stop, and the driver for the supplier will
kick in and create the IRQ domain.
Reasons for which the interrupt controller may be missing:
- It is not yet written. This may happen if a more recent DT blob (with
an interrupt-parent for the PHY) is used to boot an old kernel where
the driver didn't exist, and that kernel worked with the
vintage-correct DT blob using poll mode.
- It is compiled out. Behavior is the same as above.
- It is compiled as a module. The kernel will wait for a number of
seconds specified in the "deferred_probe_timeout" boot parameter for
user space to load the required module. The current default is 0,
which times out at the end of initcalls. It is possible that this
might cause regressions unless users adjust this boot parameter.
The proposed solution is to use the driver_deferred_probe_check_state()
helper function provided by the driver core, which gives up after some
-EPROBE_DEFER attempts, taking "deferred_probe_timeout" into consideration.
The return code is changed from -EPROBE_DEFER into -ENODEV or
-ETIMEDOUT, depending on whether the kernel is compiled with support for
modules or not.
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220407165538.4084809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add Clause 45 support for Aspeed mdio driver.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add following additional functions to move out the implementation from
aspeed_mdio_read() and aspeed_mdio_write().
c22:
- aspeed_mdio_read_c22()
- aspeed_mdio_write_c22()
c45:
- aspeed_mdio_read_c45()
- aspeed_mdio_write_c45()
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add aspeed_mdio_op() and aseed_mdio_get_data() for register accessing.
aspeed_mdio_op() handles operations, write command to control register,
then check and wait operations is finished (bit 31 is cleared).
aseed_mdio_get_data() fetchs the result value of operation from data
register.
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the MDIO bus will have the hardware default bus frequency.
Read the desired frequency of the bus from the device tree and configure
it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN966x has two internal PHYs which are in reset by default. The
driver already supported the internal PHYs of the SparX-5. Now add
support for the LAN966x, too. Add a new compatible to distinguish them.
The LAN966x has additional control bits in this register, thus convert
the regmap_write() to regmap_update_bits() to leave the remaining bits
untouched. This doesn't change anything for the SparX-5 SoC, because
there, the register consists only of reset bits.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the magic numbers by macros which are already defined. It seems
the original commit missed to use them.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver can have up to two regmaps. If the second one is registered
its debugfs entry will have the same name as the first one and the
following error will be printed:
[ 3.833521] debugfs: Directory 'e200413c.mdio' with parent 'regmap' already present!
Give the second regmap a name to avoid this.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312224140.4173930-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of DT-configured systems it may be hard to identify the PHY
interrupt in the /proc/interrupts output. Therefore add the name to
the id to make clearer that it's about a device on a muxed mdio bus.
In my case:
Now: mdio_mux-0.e40908ff:08
Before: 0.e40908ff:08
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/00b4bb1e-98f9-b4e7-5549-e095a4701f66@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.
PHY detect failure started to show after commit 7590fc6f80 ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.
10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loading of the driver when built as a module.
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's build error while CONFIG_REGMAP_MMIO is not set
and CONFIG_MDIO_MSCC_MIIM=m.
ERROR: modpost: "__devm_regmap_init_mmio_clk"
[drivers/net/mdio/mdio-mscc-miim.ko] undefined!
Add the depend of REGMAP_MMIO to fix it.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130110209.804536-1-dtcccc@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the blamed commit, the second memory resource was not considered
anymore as optional. On some platforms like sparx5 the second resource
is optional. So add it back as optional and restore the comment that
says so.
Fixes: a27a762828 ("net: mdio: mscc-miim: convert to a regmap implementation")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to a shared MDIO access implementation by way of the mdio-mscc-miim
driver.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize regmap instead of __iomem to perform indirect mdio access. This
will allow for custom regmaps to be used by way of the mscc_miim_setup
function.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap() instead of ioremap() to avoid iounmap() missing.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The second resource is optional which is only provided on the chipset
IPQ5018. But the blamed commit ignores that and if the resource is
not there it just fails.
the resource is used like this,
if (priv->eth_ldo_rdy) {
val = readl(priv->eth_ldo_rdy);
val |= BIT(0);
writel(val, priv->eth_ldo_rdy);
fsleep(IPQ_PHY_SET_DELAY_US);
}
This patch reverts that to still allow the second resource to be optional
because other SoC have the some MDIO controller and doesn't need to
second resource.
Fixes: fa14d03e01 ("net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210928134849.2092-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the documentation the second resource is optional. But the
blamed commit ignores that and if the resource is not there it just
fails.
This patch reverts that to still allow the second resource to be
optional because other SoC have the some MDIO controller and doesn't
need to second resource.
Fixes: 672a1c3949 ("net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa19644 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b601616681 ("mdio: mux: Correct mdio_mux_init error path issues")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPQ MDIO driver currently supports the chipset IPQ40xx, IPQ807x,
IPQ60xx and IPQ50xx.
Add the compatible 'qcom,ipq5018-mdio' because of ethernet LDO dedicated
to the IPQ5018 platform.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. configure the MDIO clock source frequency.
2. the LDO resource is needed to configure the ethernet LDO available
for CMN_PLL.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:
depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
OR:
depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.
Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.
Fixes: 62a6ef6a99 ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new helper function that
wraps acpi_/of_ mdiobus_register() and allows its
usage via common fwnode_ interface.
Fall back to raw mdiobus_register() in case CONFIG_FWNODE_MDIO
is not enabled, in order to satisfy compatibility
in all future user drivers.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced helper to setup both the of_node and the
fwnode for a given device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By mistake, the of_node of the MDIO device was not setup in the patch
linked below. As a consequence, any PHY driver that depends on the
of_node in its probe callback was not be able to successfully finish its
probe on a PHY, thus the Generic PHY driver was used instead.
Fix this by actually setting up the of_node.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define acpi_mdiobus_register() to Register mii_bus and create PHYs for
each ACPI child node.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor of_mdiobus_register_phy() to use fwnode_mdiobus_register_phy().
Also, remove the of_find_mii_timestamper() since the fwnode variant is
used instead.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fwnode_mdiobus_register_phy() to register PHYs on the
mdiobus. From the compatible string, identify whether the PHY is
c45 and based on this create a PHY device instance which is
registered on the mdiobus.
Along with fwnode_mdiobus_register_phy() also introduce
fwnode_find_mii_timestamper() and fwnode_mdiobus_phy_device_register()
since they are needed.
While at it, also use the newly introduced fwnode operation in
of_mdiobus_phy_device_register().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of unregister_mii_timestamper() currently check for NULL
value of mii_ts before calling it.
Place the NULL check inside unregister_mii_timestamper() and update
the callers accordingly.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of fwnode_get_phy_id(), refactor of_get_phy_id()
to use fwnode equivalent.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor of_phy_find_device() to use fwnode_phy_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define fwnode_mdio_find_device() to get a pointer to the
mdio_device from fwnode passed to the function.
Refactor of_mdio_find_device() to use fwnode_mdio_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
informations ==> information
typicaly ==> typically
derrive ==> derive
eventhough ==> even though
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
