HyperFlash devices fail to probe:
rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function. However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.
Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().
Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.
Fixes: fff53a551d ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be
Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 3e25f800af ("memory: fsl_ifc: populate child devices without
relying on simple-bus") was trying to replace the "simple-bus"
compatible with explicit bus populate in the driver. But
of_platform_populate() only populates child nodes of ifc without
populating child buses and child mfd devices residing under ifc. Change
it to of_platform_default_populate() to fix the problem.
Fixes: 3e25f800af ("memory: fsl_ifc: populate child devices without relying on simple-bus")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20220307204118.19093-1-leoyang.li@nxp.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 87108dc78e ("memory: atmel-ebi: Enable the SMC clock if specified")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220309110144.22412-1-linmq006@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Make sure to free the flash platform device in the event that
registration fails during probe.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: stable@vger.kernel.org # 5.8
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220303180632.3194-1-johan@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
There are a few separately maintained driver subsystems that we merge through
the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs,
and clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport based
on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ
and older NVIDIA Tegra chips
-----BEGIN PGP SIGNATURE-----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=Cfbk
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are a few separately maintained driver subsystems that we merge
through the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs, and
clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport
based on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
NVIDIA Tegra chips"
* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
ARM: spear: fix typos in comments
soc/microchip: fix invalid free in mpfs_sys_controller_delete
soc: s4: Add support for power domains controller
dt-bindings: power: add Amlogic s4 power domains bindings
ARM: at91: add support in soc driver for new SAMA5D29
soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
memory: emif: check the pointer temp in get_device_details()
memory: emif: Add check for setup_interrupts
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: ti: k3-socinfo: Add AM62x JTAG ID
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
...
The pointer temp is allocated by devm_kzalloc(), so it should be
checked for error handling.
Fixes: 7ec944538d ("memory: emif: add basic infrastructure for EMIF driver")
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20220225132552.27894-1-baijiaju1990@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value of the
setup_interrupts() and return error if fails.
Fixes: 68b4aee35d ("memory: emif: add interrupt and temperature handling")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220224025444.3256530-1-jiasheng@iscas.ac.cn
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
1. Several updates in the MTK SMI bindings.
2. Add support for MT8186 MTK SMI and improvements in support for MT8195.
-----BEGIN PGP SIGNATURE-----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=V7gd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Bquy
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-mediatek-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.18 - Mediatek SoC
1. Several updates in the MTK SMI bindings.
2. Add support for MT8186 MTK SMI and improvements in support for MT8195.
* tag 'memory-controller-drv-mediatek-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: mtk-smi: Enable sleep ctrl safety function for MT8195
memory: mtk-smi: mt8186: Add smi support
memory: mtk-smi: Add sleep ctrl function
memory: mtk-smi: handle positive return value for clk_bulk_prepare_enable
dt-bindings: memory: mediatek: Add mt8186 support
dt-bindings: memory: mtk-smi: Correct minItems to 2 for the gals clocks
dt-bindings: memory: mtk-smi: No need mediatek,larb-id for mt8167
dt-bindings: memory: mtk-smi: Rename clock to clocks
Link: https://lore.kernel.org/r/20220228164313.52931-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the code parsing the "jedec,lpddr2" device tree
binding to use the new `revision-id` property instead of the deprecated
`revision-id1` and `revision-id2` properties if available.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Link: https://lore.kernel.org/r/20220224003421.3440124-3-jwerner@chromium.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Passing the memory timings maximum frequency as an unit address was
a workaround and instead 'max-freq' is preferred. Look for 'max-freq'
first and then fallback to 'reg'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.ahtar@samsung.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220206135807.211767-8-krzysztof.kozlowski@canonical.com
Enable the sleep ctrl function to wait until all the queued commands
are executed before suspending the LARBs, like done for MT8186.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220204125543.1189151-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
After adding device_link between the iommu consumer and smi-larb,
the pm_runtime_get(_sync) of smi-larb and smi-common will be called
automatically. we can get rid of mtk_smi_larb_get/put.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The double `to' in the comment in line 427 is repeated. Remove it
from the comment.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211212033347.67921-1-wangborong@cdjrlc.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The only usage of tegra210_emc_cd_ops is to pass its address to
devm_thermal_of_cooling_device_register() which is a pointer to const
struct thermal_cooling_device_ops. Make it const to allow the compiler
to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211128204158.19544-1-rikard.falkeborn@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
After we update the binding to not use simple-bus compatible for the
controller, we need the driver to populate the child devices explicitly.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20211116211846.16335-3-leoyang.li@nxp.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This definition is tied to the number of SMI common clocks (the array
mtk_smi_common_clks): improve the definition by using the ARRAY_SIZE
macro instead. That will also reduce room for mistakes when updating
the aforementioned array in the future.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20211015151557.510726-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Memory chip select is swapped when we read mode register, correct it.
We didn't have devices that use a single LPDDR chip and both chips are
always identical, hence this change is just a minor improvement.
Fixes: 131dd9a436 ("memory: tegra20-emc: Support matching timings by LPDDR2 configuration")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211222043215.28237-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Print out memory type and LPDDR2 configuration on Tegra30, making it
similar to the memory info printed by the Tegra20 memory driver. This
info is useful for debugging purposes.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # T30 ASUS TF201 LPDDR2
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211222043215.28237-1-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Sleep control means that when the larb goes to sleep, we should wait a bit
until all the current commands are finished. Thus, when the larb runtime
suspends, we need to enable this function to wait until all the existed
commands are finished. When the larb resumes, just disable this function.
This function only improves the safety of bus. Add a new flag for this
function. Prepare for mt8186.
Signed-off-by: Anan Sun <anan.sun@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-7-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Function clk_bulk_prepare_enable() returns 0 for success or a negative
number for error, although the common style for the callers is to check
always for any non-zero return value (just like its implementation in
clk.h does). Adjust the code to such coding style.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-6-yong.wu@mediatek.com
[krzysztof: rewrite commit msg]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
* mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
* gen_probe: Use bitmap_zalloc() when applicable
* Introduce an expert mode for forensics and debugging purposes
* Clear out unregistered devices a bit more
* Provide unique name for nvmem device
* Remove unused header file <linux/mtd/latch-addr-flash.h>
* Fixed breaking list in __mtd_del_partition.
MTD device changes:
* sst25l, mchp48l640, mchp23k256, dataflash:
- Warn about failure to unregister mtd device
Raw NAND core changes:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
* Add Pratyush as SPI NOR co-maintainer.
* Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
* Rework the flash_info flags and clarify where one should be used.
* Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
* Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
* Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
* Fix mtd size for s3an flashes.
* Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Hyperbus changes:
* Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO+g8ACgkQJWrqGEe9
VoRW1AgAjFC58ARNBw7asYerGyiUWv7b8RjPIRWZqmcSQ6D5m20cGNBTa15c2NrC
v0dNMf2+3FrCECso6wKPbkEbLt9lHjlMmt+AdlraV0QvHBXrJq/Tc2p2ATI5kTqq
WaP4oCx1mccgO+IrEIiGikOcFx/TLBBJEk+U0Anbm16eia9Cjw+uD/q7X2HbF5xQ
MOFZyQ+rAVqkM8tCh6VHhCpX85pn9pj2ZdouOhPWsqjULaGqDbUopC70YPZLVJyx
9u4xHFaVLVae6AS5Gitser2ie8klypTN/H+1weSao43GGmwIrT0wK0mCOVIm90Zd
4frlpnt4QE/IIAKgAm+HxkWg+KV9qg==
=E8lV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
As more compatibles can be added to the GPMC NAND controller driver
use a compatible match table.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-4-rogerq@kernel.org
[krzysztof: remove "is_nand" variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The TI's AM64 SoC has the GPMC module. Add compatible for it.
Traditionally GPMC external addresses have always been mapped to first
1GB physical address. However newer platforms, can have it mapped
at different locations. Support this address provision via device tree.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20211221131757.2030-3-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20211221203916.18588-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
We add the ostd setting for mt8195. It introduces a KE for the
previous SoC which doesn't have ostd setting. This is the log:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000080
...
pc : mtk_smi_larb_config_port_gen2_general+0x64/0x130
lr : mtk_smi_larb_resume+0x54/0x98
...
Call trace:
mtk_smi_larb_config_port_gen2_general+0x64/0x130
pm_generic_runtime_resume+0x2c/0x48
__genpd_runtime_resume+0x30/0xa8
genpd_runtime_resume+0x94/0x2c8
__rpm_callback+0x44/0x150
rpm_callback+0x6c/0x78
rpm_resume+0x310/0x558
__pm_runtime_resume+0x3c/0x88
In the code: larbostd = larb->larb_gen->ostd[larb->larbid],
if "larb->larb_gen->ostd" is null, the "larbostd" is the offset(e.g.
0x80 above), it's also a valid value, then accessing "larbostd[i]" in the
"for" loop will cause the KE above. To avoid this issue, initialize
"larbostd" to NULL when the SoC doesn't have ostd setting.
Fixes: fe6dd2a401 ("memory: mtk-smi: mt8195: Add initial setting for smi-larb")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211108082429.15080-1-yong.wu@mediatek.com
Link: https://lore.kernel.org/r/20211124085042.9649-3-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Don't use _HIZ macros but also provide a val. This is more consistent
with the other macros and, thus, easier to read. Also shorter.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211119110442.4946-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Instead of writing fixed values with undocumented bits which happen to
be set on some SoCs, better switch to read-modify-write operations
changing only bits which are documented. This is way more future-proof
as we don't know yet how these bits may be on upcoming SoCs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117093710.14430-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
No need to open code regmap_update_bits().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117102902.20062-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.
This patch adds a new compatible string for the RZ/G2L family so
that the timing values on RZ/G2L can be adjusted.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211025205631.21151-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
RPCIF_DIRMAP_SIZE may differ on various SoC's. Instead of using
RPCIF_DIRMAP_SIZE macro use resource size to get dirmap size
which is already part of struct rpcif.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 EMC driver uses simple devfreq governor. Add simple devfreq
governor to the list of the Tegra20 EMC driver module softdeps to allow
userspace initramfs tools like dracut to automatically pull the devfreq
module into ramfs image together with the EMC module.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Suggested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211019231524.888-1-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
ASUS Transformer TF101 doesn't provide RAM code and in this case memory
timings should be selected based on identity information read out from
SDRAM chip. Support matching timings by LPDDR2 configuration.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211006224659.21434-10-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add common helpers for reading and parsing standard LPDDR2 configuration
properties.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211006224659.21434-9-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
1. Renesas RPC: fix unaligned bus access and QSPI data transfers in
manual modes.
2. Renesas RPC: select RESET_CONTROLLER as it is necessary for
operation.
3. FSL IFC: fix error paths.
4. Broadcom: allow building as module.
-----BEGIN PGP SIGNATURE-----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=ZsTv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFkDP4ACgkQmmx57+YA
GNnOzRAAxRm9E9hFwaqKoyEopnuxJRFxxjXFS8hM8GieiwD5upJBBtB7HjGqcfBC
i5RZV9RRKU2v04tdddkWhS4Pcw52eEmE/T77uMhr8UwaOzzkuVgKdOz432XuVCwf
2O6oGS2igTTWMKakb+4Zza9q3PXPuUdFgXyOBdeB1PF96RnV9qjSRviwpp+P75fj
9X0ikocRVo80hCDMsiTtYwzd10CbslVIOv9wWHSa7kKQzuHJbALYL4mjnlvF4bCo
9iDVu+UJCsAhd16Xtks2VtewYmox+n/+q/ThKDU0IB2I9kdR5tvpkQqPhdn8W0Fj
LiJDfDexB5rS3o9E/ws6CJGFhMxI9QFyMLXGq8HAXHjRGTIlCKA53DqpH2r10Hlj
5mzuNRfxyo2mAu2sXzDF2ScVXImsSGN65evdsFFOlohVbivhq5AZzpYnQBT/tR1K
E4srv07jl7FxI03YavNevq3fqzE+SSZ1cX8PAcKY7qeueci4yPmd9/7SiJLqyHDd
Q5B2q60bbCF3E7F0UQpKMjq1ZB0jO16PKYZ1BzOtXLQloC6HRR+HuLMpsyLEb09d
4aAwWl3Xa183t9lTLCuzZuC3b8qZgwcKrVrDO+Rigb8adtlOVAQFoqWZthzhL3Ys
nIRY2wc83rtJ/uSghFEe1sLZvZ+2K9nEWD0wInejtq+GqhqWn9s=
=OOXj
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.16
1. Renesas RPC: fix unaligned bus access and QSPI data transfers in
manual modes.
2. Renesas RPC: select RESET_CONTROLLER as it is necessary for
operation.
3. FSL IFC: fix error paths.
4. Broadcom: allow building as module.
* tag 'memory-controller-drv-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: fsl_ifc: fix leak of irq and nand_irq in fsl_ifc_ctrl_probe
memory: renesas-rpc-if: RENESAS_RPCIF should select RESET_CONTROLLER
memory: brcmstb_dpfe: Allow building Broadcom STB DPFE as module
memory: samsung: describe drivers in KConfig
memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
dt-bindings: rpc: renesas-rpc-if: Add support for the R8A779A0 RPC-IF
Link: https://lore.kernel.org/r/20211010175836.13302-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add MT8195 support to the Mediatek SMI memory controller driver. This
brings also several cleanups and minor enhancements before adding actual
new device support.
-----BEGIN PGP SIGNATURE-----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=mga+
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFkDLYACgkQmmx57+YA
GNlQoxAAg6UiMSe7Ew8SXPEciwvdzt+uOOaNCDgyR6HOEYtOyQjNe2BZk+5blpTV
LVDD0iG4CujyY70zsboBGqYRrfXjPWzdwt37/1WHT5r6AWtKKbAFfhwg5ixE7xh7
pFVFp07mMYZVFHWwNCmuG7UPD9cOZuixXiMMB7KWUHSa8/Y+CaU5OTSA0j83ksut
8bRJT7fzd4mD2UJUqxb50/UsuHHs+9f8xe+aY7FqUfmqpozDnSmQmCowbE9OUYjA
4E1xOtn9MFS8cX1enBdcB2gHuK81RxhYNUnxW/BZfu1y/t7hpn/Akun/XI4czneE
7GPniw3wmcqtgkkJh1SdwbJCIm9nAqX2ldKKUv85XSAncuHx5JOxc6efEBS0uo8x
M3XDm7DR8UXVTWJd4TtEoyD/i81mpZaccpaKKscSyPXU/wsHIFxNwmJAUvqpFDy0
WRP7o6N+ckIQZE1l+jhPTEk2W3uK9TmD6GvKpfIKCsE8ro5Vsps4bAHLERVezom1
Aeunk8FrxkueO8Pv1zL6tsdOMB+UK0kYv+FaQGRRZAWdl2UPt1Q2J/v5t0kxbrCo
oeAHdnER+rjN2tI5POmhjkV+FJKGcJU7pX+OGvVGaFjhtJiK1/D925Bz4HZmRYGu
WxVK7lWy0jcdQNb9uTsfCb6LeZGiVMo5f+6o8UT6Wt9Mn6HjJhg=
=HHse
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-mtk-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.14 - Mediatek
Add MT8195 support to the Mediatek SMI memory controller driver. This
brings also several cleanups and minor enhancements before adding actual
new device support.
* tag 'memory-controller-drv-mtk-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
MAINTAINERS: Add entry for MediaTek SMI
memory: mtk-smi: mt8195: Add initial setting for smi-larb
memory: mtk-smi: mt8195: Add initial setting for smi-common
memory: mtk-smi: mt8195: Add smi support
memory: mtk-smi: Use devm_platform_ioremap_resource
memory: mtk-smi: Add clocks for smi-sub-common
memory: mtk-smi: Add device link for smi-sub-common
memory: mtk-smi: Add error handle for smi_probe
memory: mtk-smi: Adjust some code position
memory: mtk-smi: Rename smi_gen to smi_type
memory: mtk-smi: Use clk_bulk clock ops
dt-bindings: memory: mediatek: Add mt8195 smi sub common
dt-bindings: memory: mediatek: Add mt8195 smi binding
Link: https://lore.kernel.org/r/20211010175836.13302-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
fix debugfs_simple_attr.cocci warning:
drivers/memory/tegra/tegra210-emc-core.c:1665:0-23: WARNING:tegra210_emc_debug_min_rate_fops
should be defined with DEFINE_DEBUGFS_ATTRIBUTE
Commit 6fc5f1adf5 ("memory: tegra210-emc: replace
DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE") fixed the same
warning, but didn't fix all matches in this file at once.
Signed-off-by: Kai Song <songkai01@inspur.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211005043514.9650-1-songkai01@inspur.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Renesas RPC-IF driver calls devm_reset_control_get_exclusive(),
which returns -ENOTSUPP if CONFIG_RESET_CONTROLLER is not enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/e443aa66d146da5646b7ebece8876545b8621063.1633447756.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Return the error code when command fails.
Fixes: 13324edbe9 ("memory: tegra186-emc: Handle errors in BPMP response")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210928021545.3774677-1-yangyingliang@huawei.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Allow building the Broadcom STB DPFE driver as a module, it is already a
platform driver proper with all of the resource releasing device
managed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Link: https://lore.kernel.org/r/20210924031459.8911-1-f.fainelli@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
HyperFlash devices in Renesas SoCs use 2-bytes addressing, according
to HW manual paragraph 62.3.3 (which officially describes Serial Flash
access, but seems to be applicable to HyperFlash too). And 1-byte bus
read operations to 2-bytes unaligned addresses in external address space
read mode work incorrectly (returns the other byte from the same word).
Function memcpy_fromio(), used by the driver to read data from the bus,
in ARM64 architecture (to which Renesas cores belong) uses 8-bytes
bus accesses for appropriate aligned addresses, and 1-bytes accesses
for other addresses. This results in incorrect data read from HyperFlash
in unaligned cases.
This issue can be reproduced using something like the following commands
(where mtd1 is a parition on Hyperflash storage, defined properly
in a device tree):
[Correct fragment, read from Hyperflash]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=32 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa f6 03 02 aa f7 03 03 aa |................|
00000010 00 00 80 d2 40 20 18 d5 00 06 81 d2 a0 18 a6 f2 |....@ ..........|
00000020
[Incorrect read of the same fragment: see the difference at offsets 8-11]
root@rcar-gen3:~# dd if=/dev/mtd1 of=/tmp/zz bs=12 count=1
root@rcar-gen3:~# hexdump -C /tmp/zz
00000000 f4 03 00 aa f5 03 01 aa 03 03 aa aa |............|
0000000c
Fix this issue by creating a local replacement of the copying function,
that performs only properly aligned bus accesses, and is used for reading
from HyperFlash.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Link: https://lore.kernel.org/r/20210922184830.29147-1-andrew_gabbasov@mentor.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>