This removes a lot of ancient cruft from the Ux500 SMP boot.
Instead of the pen grab/release, just point the ROM to
secondary_boot() and start the second CPU there, then send
the IPI.
Use our own SMP enable method. This enables us to remove the
last static mapping and get both CPUs booting properly.
Tested this and it just works.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ux500 SoC uses the generic PM domain and requires the domains to be
specified through DT.
Currently the genpd callbacks for handling power gating|ungating are
implemented as dummy functions. To be able to enable those to perform
PM domain gating/ungating, each device that resides in the VAPE domain
must be properly handled from a runtime PM perspective.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since all platform data has been transfered to DT, we don't need the
container for the mmci platform data anymore. Remove the file and the
corresponding references to it's data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This moves the set-up of the HREF500 with its AB8505 ASIC to
a device tree include. Since there is not yet any device tree
for this board the DTSI is currently unused. After this delete
the board file for pins for good and migration of pins to the
device tree is complete.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decomission the AMBA device register functions.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the platform data from all these files into one, delete empty
files and remove all references to them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit f1ff5b2549
"ARM: ux500: Stop enabling GPIOs when not booting with Device Tree"
deleted devices-common.c, but did not delete the build
rule from Makefile (most likely due to compiling in
a dirty tree where the object file still existed so
linking would complete anyway).
Delete the makerule, the header file associated
with this file and the remaining reference to the header.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no more dependency with arch/arm headers, so we can safely move the
driver to the drivers/cpuidle directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
If we try to build this file in a multiplatform configuration with
ARMv6 enabled, gas complains about the dsb operation being undefined.
Adding -march=armv7-a is safe because that code is only ever run
on ux500, which is Cortex-A9.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.
Basically we are left with the two alternatives of code
placement as:
- arch/arm/mach-ux500/pm.c - this because the code is
closely related to the GIC, and takes ownership of
some of the registers from the PRCMU related to this
PM functionality.
- drivers/mfd/db8500-prcmu-pm.c - because the code is
affecting stuff in the PRCMU register range. But then
this code needs to remap and handle GIC registers.
This patch implementation is taking the first approach.
Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.
The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
The 'msp' board file does more than just register MSP devices. It
also registers some other components necessary to get audio working
on ux500 based platforms; such as the PCM and Machine Drivers. For
that reason we're changing the filename to be more encompassing -
'audio'.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove machine specific clock implementation and switch to use
new common clock framework.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Power management changes here are mostly for the omap platform, but also
include cpuidle changes for ux500 and suspend/resume code for mmp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oGcZ
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
At the beginning of the first patch series I included the custom
ux500 pin control system to make sure I could eventually replace
it with the standard subsystem driver. So now that we've done so,
let's remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the cpuidle driver for the ux500 SoC.
The boards saves 12mA with these states. It is based on the latest
cpuidle consolidation from Robert Lee.
The cpu can go to retention only if the other core is in WFI.
If the other cpu is in WFI and we decoupled the gic from the cores,
then we have the guarantee, it won't be wake up.
It is up to the prcmu firmware to recouple the gic automatically
after the power state mode is selected.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This platform has been obsoleted and was only available inside of
ST-Ericsson, no users of this code are left in the world. This
deletes the core U5500 support entirely in the same manner as the
obsoleted U8500 silicon was previously deleted.
The cpu_is_u5500() macros that can read out the CPU ID is left
until the next kernel cycle, this makes it possible to merge
deletion of dependent drivers without breakage.
This also has the upside of removing the mailbox driver which was
our only driver that was outside the drivers/* hiearchy, now the
machine directory only handles machines and nothing else.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create devices for the MSP-blocks (MSP0, MSP1, MSP2 and MSP3)
and associate it with the correct clocks in the clock-framework.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement an API to allow a list of pincfgs to be remuxed to active
and sleep modes, for power saving. This is not exported on purpose,
because it is not to be called by drivers directly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree
based booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=z4Mj
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: timer cleanup work" from Arnd Bergmann:
"These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree based
booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
ARM: tegra: select USB_ULPI if USB is selected
arm/tegra: pcie: fix return value of function
ARM: ux500: fix compilation after local timer rework
ARM: shmobile: remove additional __io() macro use
ARM: local timers: make the runtime registration interface mandatory
ARM: local timers: convert MSM to runtime registration interface
ARM: local timers: convert exynos to runtime registration interface
ARM: smp_twd: remove old local timer interface
ARM: imx6q: convert to twd_local_timer_register() interface
ARM: highbank: convert to twd_local_timer_register() interface
ARM: ux500: convert to twd_local_timer_register() interface
ARM: shmobile: convert to twd_local_timer_register() interface
ARM: tegra: convert to twd_local_timer_register() interface
ARM: plat-versatile: convert to twd_local_timer_register() interface
ARM: OMAP4: convert to twd_local_timer_register() interface
ARM: smp_twd: add device tree support
ARM: smp_twd: add runtime registration support
ARM: local timers: introduce a new registration interface
ARM: smp_twd: make local_timer_stop a symbol instead of a #define
ARM: mach-shmobile: default to no earlytimer
...
Add support for the new smp_twd runtime registration interface
to the ux500 platforms, and remove the old compile-time support.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
First rename the config option MACH_U8500 to MACH_MOP500
because that is what it's obviously all about, this has
confused me for the last time. Fix some whitespace in the
process.
Since the machine descriptors for HREFv60 and snowball
are clearly in the file board-mop500.c which only
compiles if MACH_MOP500 (former MACH_U8500) is set,
select this for the board variants and nothing else.
For the MOP500 variants the UIB (user interface board)
is probed using I2C so select I2C and I2C_NOMADIK so
we know that this probe will always be successful.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The timer and cleanup branches from stericsson conflict,
so I'm merging them here.
Conflicts:
arch/arm/mach-ux500/Makefile
arch/arm/mach-ux500/cpu.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just split off the timer code to its own file so we have a
more fine-grained file tree.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Following mach-imx we break out the l2x0 handling into its
own file, avoiding some ifdefs. Also remove unnecessary creation
of local pointers when there is already one file-local readily
available.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have decided that this function arbiter fits better in the MFD
subsystem. Since we need to concatenate the split header files we move
it basically like this:
mv mach-ux500/prcmu-db8500.c drivers/mfd/db8500-prcmu.c
mv mach-ux500/include/mach/prcmu-defs.h include/linux/mfd/db8500-prcmu.h
mv mach-ux500/include/mach/prcmu-regs.h drivers/mfd/db8500-prcmu-regs.h
mach-ux500/include/mach/prcmu.h >> include/linux/mfd/db8500-prcmu.h
rm arch/arm/mach-ux500/include/mach/prcmu.h
Then we update different #include statements and Makefile orders etc
to make the PRCMU driver compile, link and boot in the new place
without really changing any code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include ab8500 regulators for DB8500 SoC by default
and fix build issues
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
[Small fixup for changed boardfiles]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dynamically detect the DBx500 SOC an revision based on the ASIC ID.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the MOP board Kconfig entries to the same name as the machine
type, so that the machine_is_*() macros work correctly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Updated to match changes in the tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Suffix the U5500 modem IRQ and MBOX files with *-db5500* so that
we clearly know the SoC they belong to, in line with the rest of
the files in mach-ux500.
Cc: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Cc: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Move keylayouts to a dedicated file and plug these keylayouts
for input platform data. This will make addition of new and custom
keylayouts localized.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Add basic DMA configuration for u5500 supporting memcpy.
Make way for SDI0 dma support by setting SDI0 to -1,
indicating it will be configured in runtime.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
U5500 now boots from sdi0 (onboard eMMC).
Change machine type to U5500.
Adjust uart and sdi0 clock rates for u5500.
All necessary clocks must be enabled before Linux starts because
there is no clock tree support in u5500 yet.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Change the Ux500 devices to be dynamically allocated and added by
calling functions instead of referencing structures, thereby allowing
5500 and other derivatives' support to be added without having to
duplicate structures, use fixup functions, or use compile-time macros.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This rounds of the DB5500 mailbox patches by adding the Kconfig
options to enable the modem IRQs and mailboxes.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
