drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pctl_dt_node_to_map:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:720:8: error: implicit declaration of function pinconf_generic_dt_node_to_map_all;
drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pinctrl_probe:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:1022:15: error: struct gpio_chip has no member named of_node
pc->gpio_chip.of_node = np;
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0de704955e ("pinctrl: bcm2835: Add support for generic pinctrl binding")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using STM32 as guinea pig after Alex's initial positive
test to see if this is something we should encourage
in general and make default behaviour.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting this up will configure wake from suspend properly,
and wake only for the interrupts that are setup in wake_mask,
not all interrupts.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl variants that include pinctrl-paris.h (and not
pinctrl-mtk-common.h) also need to use pm_ops to setup
wake mask properly, so copy over the pm_ops from common
to paris variant.
It is not easy to merge the 2 copies (or move
mtk_eint_suspend/resume to mtk-eint.c), as we need to
dereference pctrl->eint, and struct mtk_pinctrl *pctl has a
different structure definition for v1 and v2 (which is
what paris variant uses).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 has PCIE L5 rst and clkreq pins which need to be controlled
dynamically at runtime. This driver supports change pinmux for these
pins. Pinmux for rest of the pins is set statically by bootloader and
will not be changed by this driver
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Suresh Mangipudi <smangipudi@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 chip has 32 bit pinctrl registers. Existing register defines in
header are only 16 bit.
Modified common pinctrl-tegra driver to support 32 bit registers of
Tegra 194 and later chips.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinconf support for Bitmain BM1880 SoC. Pinconf support includes
pin bias, slew rate and schmitt trigger. Drive strength support will
be added later.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rework the BM1880 SoC pinmux handling by removing the
BM1880_PINMUX_FUNCTION_MUX define and merging it with the
BM1880_PINMUX_FUNCTION definition. Since the PWM muxing is handled by
generic pin controller in the SoC itself, there is no need to have a
dedicated code to do the muxing in PWM registers. So, lets club all
pinmux handling in the same per pin mux handling code.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT
in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs are split between several banks (A, B, ...) and each bank can have
up to 16 lines. Those GPIOs could be used as interrupt lines thanks to
exti lines. As there are only 16 exti lines, a mux is used to select which
gpio line is connected to which exti line. Mapping is done as follow:
-A0, B0, C0.. -->exti_line_0 (X0 selected by mux_0)
-A1, B1, C1.. -->exti_line_1 (X1 selected by mux_1)
...
This patch adds a protection to avoid overriding on mux_n for exti_line_n.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During power sequence, GPIO hardware registers could be lost if the power
supply is switched off. Each device using pinctrl API is in charge of
managing pins during suspend/resume sequences. But for pins used as gpio or
irq stm32 pinctrl driver has to save the hardware configuration.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hogs would create circular device links, so do not link
the device to itself.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set create_link to inform pinctrl core that stmfx wants to create
link with its consumers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A pin controller may want to create a link between itself
and its clients to be sure of suspend/resume call ordering.
Introduce link_consumers field in pinctrl_desc structure to let
pinctrl core knows that controller expect to create a link.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
[Renamed create_link to link_consumers]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips
like BCM7211 which adopted that pin controller for GPIO. This
commit makes the option menu configurable with default enabled
for ARCH_BRCMSTB and ARCH_BCM2835.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
rework bias enable/disable part to prepare drive-strength integration
no functional changes
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
drivers/pinctrl/pinctrl-stmfx.c:441 stmfx_pinctrl_irq_set_type() warn: bitwise AND condition is false here
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
smatch warnings:
drivers/pinctrl/pinctrl-stmfx.c:225 stmfx_pinconf_get() warn: unsigned 'dir' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:228 stmfx_pinconf_get() warn: unsigned 'type' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:231 stmfx_pinconf_get() warn: unsigned 'pupd' is never less than zero.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
module_i2c_driver and pinconf_generic_dt_node_to_map_pin are undeclared
if CONFIG_I2C and CONFIG_OF are not enabled.
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on generic pin config interface to configure the GPIOs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is expected that some of these operations won't work on each and
every HW. Previously, even a simple `cat
/sys/kernel/debug/pinctrl/spi1.1/pinconf-pins` caused excessive dmesg
output.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Non-critical fixes for Intel Baytrail and Intel Cedarfork.
Couple of fixes for all pinctrl-intel based drivers with regard to
IRQ handling, i.e. moving PM calls to noirq level to avoid IRQ lose
and restore ownership of pins to prevent IRQ masking side effect.
The following is an automated git shortlog grouped by driver:
baytrail:
- Fix potential NULL pointer dereference
cedarfork:
- Update pin names according to v1.13c
intel:
- Increase readability of intel_gpio_update_pad_mode()
- Retain HOSTSW_OWN for requested gpio pin
- move gpio suspend/resume to noirq phase
-----BEGIN PGP SIGNATURE-----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=tsfB
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.2-1
Non-critical fixes for Intel Baytrail and Intel Cedarfork.
Couple of fixes for all pinctrl-intel based drivers with regard to
IRQ handling, i.e. moving PM calls to noirq level to avoid IRQ lose
and restore ownership of pins to prevent IRQ masking side effect.
The following is an automated git shortlog grouped by driver:
baytrail:
- Fix potential NULL pointer dereference
cedarfork:
- Update pin names according to v1.13c
intel:
- Increase readability of intel_gpio_update_pad_mode()
- Retain HOSTSW_OWN for requested gpio pin
- move gpio suspend/resume to noirq phase
Make the BM1880 SoC pinctrl driver depend on COMPILE_TEST to get compiler
test coverage and also select this driver by default for ARCH_BITMAIN
platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl support for Bitmain BM1880 SoC. The driver only handles
pinmuxing as the SoC is not capable of handling pinconf.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is not guaranteed that the IRQ controller driver is probed before
the pin controller driver gets probed.
Considering this, check for the irq domain availability during probe
and return EPROBE_DEFER if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the pinctrl driver for the MediaTek's MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/zte/pinctrl-zx.c:415:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:422:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:436:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:444:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:448:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We better to use usual pattern for read-modify-update,
than doing some operations in definition block.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The touchpad of the ASUS laptops E403NA, X540NA, X541NA are not
responsive after suspend/resume. The following error message
shows after resume.
i2c_hid i2c-ELAN1200:00: failed to reset device.
On these laptops, the touchpad interrupt is connected via a GPIO
pin which is controlled by Intel pinctrl. After system resumes,
the GPIO is in ACPI mode and no longer works as an IRQ.
This commit saves the HOSTSW_OWN value during suspend, make sure
the HOSTSW_OWN mode remains the same after resume.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c13 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
H6 has a different I/O voltage bias setting method than A80. Prepare
existing code for using alternative bias voltage setting methods.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1188:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-st.c:1199:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1175, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_find_compatible_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:76:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
./drivers/pinctrl/samsung/pinctrl-exynos-arm.c:82:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 66, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Align pins names with names provided in official stm32mp157 datasheet
available on st.com.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A same SoC can be available in several packages. Differences between
packages are only the numbers of available balls. In order not to write
a driver for each new package, same driver (ex: pinctrl-stm32mp157.c) will
be used. This patch introduces the "package" property for each pin. So on a
same driver, it will be possible to indicate on which package the pin is
available. The package information will be got from the device tree.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To support pinctl hog restore after LPSR resume back,
add the generic suspend/resume in pinctrl-imx along with the
generic pm ops to be used by platform specific drivers. Then
make use of the newly added ops in i.MX8MQ platform specific
driver.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pincontrol callbacks used to be symmetric:
enable/disable.
However for a while we only have one function that
set the muxing, no disabling.
Drop the unused disable function, and rename the
*enable() function to *set().
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In current driver, SET_LATE_SYSTEM_SLEEP_PM_OPS is used to install the
callbacks for suspend/resume.
GPIO pin may be used as the interrupt pin by some device. However, using
SET_LATE_SYSTEM_SLEEP_PM_OPS() to install the callbacks, the resume
callback is called after resume_device_irqs(). Unintended interrupts may
arrive due to resuming device irqs first, but the GPIO controller is not
properly restored.
Normally, for a SMP system, there are multiple cores, so even when there are
unintended interrupts, BSP gets the chance to initialize the GPIO chip soon.
But when there is only 1 core is active (other cores are offlined or
single core) during resume, it is more easily to observe the unintended
interrupts.
This patch renames the suspend/resume function by adding suffix "_noirq",
and installs the callbacks using SET_NOIRQ_SYSTEM_SLEEP_PM_OPS().
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some of the AMD reference boards used single GPIO line for
multiple devices. So added IRQF_SHARED flag in amd pinctrl driver.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
