Commit Graph

166890 Commits

Author SHA1 Message Date
Ben Dooks
68c5ed592f s3cmci: DMA fixes
Fixes for the DMA transfer mode of the driver to try and improve the state
of the code:

- Ensure that dma_complete is set during the end of the command phase
  so that transfers do not stall awaiting the completion

- Update the DMA debugging to provide a bit more useful information
  such as how many DMA descriptors where not processed and print the
  DMA addresses in hexadecimal.

- Fix the DMA channel request code to actually request DMA for the
  S3CMCI block instead of whatever '0' signified.

- Add fallback to PIO if we cannot get the DMA channel, as many of the
  devices with this block only have a limited number of DMA channels.

- Only try and claim and free the DMA channel if we are trying to use it.

This improves the driver DMA code to the point where it can now identify a
card and read the partition table.  However the DMA can still stall when
trying to move data between the host and memory.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
26f14947db s3cmci: Kconfig selection for PIO/DMA/Both
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.

The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
c225889375 s3cmci: add SDIO IRQ support
The controller supports SDIO IRQ detection so add support for hardware
assisted SDIO interrupt detection for the SDIO core.  This improves the
response time for SDIO interrupts and thus the transfer rate from devices
such as the Marvel 8686.

As a note, it does seem that the controller will miss an IRQ than is held
asserted, so there are some manual checks to see if the SDIO interrupt is
active after a transfer.

Major testing on the S3C2440.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
9bdd203b4d s3cmci: add debugfs support for examining driver and hardware state
Export driver state and hardware register state via debugfs entries
created under a directory formed from dev_name() on the probed device when
CONFIG_DEBUG_FS is set.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
e6130aeffd s3cmci: fix direct write to interrupt mask
The clear_imask() call should be used to clear the interrupt mask
register, as it may end up clearing the SDIO interrupt bit if this is
enabled.

Change all writes of zero to SDIIMSK register to use clear_imask() ready
for the SDIO updates.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
50d7fa9aa4 s3cmci: change to use dev_pm_ops
Move to using dev_pm_ops for suspend and resume.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Ben Dooks
916a30775f s3cmci: change GPIO to gpiolib from S3C24XX specific calls
Move to using gpiolib to access the card detect and write protect GPIO
lines instead of using the platform speicifc s3c2410_gpio calls.

Also ensure that the card lines are claimed the same way to avoid overlap
with any other drivers.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:14 -07:00
Ben Dooks
44d0e19968 s3cmci: update probe to use new platform id list
Use the platform id list to match the three different versions of the
hardware block that this driver supports.

This will change the prefix of the console messages produced by this
driver to be prefixed by s3c-mci instead of the hardware block name, such
as s3c2440-mci.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:14 -07:00
Ben Dooks
da52a7ca7a s3cmci: use resource_size() instead of local macro
Replace the local definition RESSIZE() with the standard resource_size()
call for getting the size of a struct resource.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:14 -07:00
KAMEZAWA Hiroyuki
ef8745c1e7 memcg: reduce check for softlimit excess
In charge/uncharge/reclaim path, usage_in_excess is calculated repeatedly
and it takes res_counter's spin_lock every time.

This patch removes unnecessary calls for res_count_soft_limit_excess.

Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:13 -07:00
KAMEZAWA Hiroyuki
4e649152cb memcg: some modification to softlimit under hierarchical memory reclaim.
This patch clean up/fixes for memcg's uncharge soft limit path.

Problems:
  Now, res_counter_charge()/uncharge() handles softlimit information at
  charge/uncharge and softlimit-check is done when event counter per memcg
  goes over limit. Now, event counter per memcg is updated only when
  memory usage is over soft limit. Here, considering hierarchical memcg
  management, ancesotors should be taken care of.

  Now, ancerstors(hierarchy) are handled in charge() but not in uncharge().
  This is not good.

  Prolems:
  1. memcg's event counter incremented only when softlimit hits. That's bad.
     It makes event counter hard to be reused for other purpose.

  2. At uncharge, only the lowest level rescounter is handled. This is bug.
     Because ancesotor's event counter is not incremented, children should
     take care of them.

  3. res_counter_uncharge()'s 3rd argument is NULL in most case.
     ops under res_counter->lock should be small. No "if" sentense is better.

Fixes:
  * Removed soft_limit_xx poitner and checks in charge and uncharge.
    Do-check-only-when-necessary scheme works enough well without them.

  * make event-counter of memcg incremented at every charge/uncharge.
    (per-cpu area will be accessed soon anyway)

  * All ancestors are checked at soft-limit-check. This is necessary because
    ancesotor's event counter may never be modified. Then, they should be
    checked at the same time.

Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:13 -07:00
KAMEZAWA Hiroyuki
3dece8347d cgroup: catch bad css refcnt at css_put
__css_put() doesn't check a bug as refcnt goes to minus.
I think it should be caught. This patch adds a check for it.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
KAMEZAWA Hiroyuki
26251eaf98 memcg: fix refcnt going negative
__mem_cgroup_largest_soft_limit_node() returns a mem_cgroup_per_zone "mz"
with incremnted mz->mem->css's refcnt.  Then, the caller of this function
has to call css_put(mz->mem->css).

But, mz can be !NULL even if "not found" i.e.  without css_get().  By
this, css->refcnt will go down to minus.

This may cause various things...one of results will be
initite-loop in css_tryget()  as this.

INFO: RCU detected CPU 0 stall (t=10000 jiffies)
sending NMI to all CPUs:
NMI backtrace for cpu 0
CPU 0:
<snip>

 <<EOE>>  <IRQ>  [<ffffffff810884bd>] trace_hardirqs_off+0xd/0x10
  [<ffffffff8102a940>] flat_send_IPI_mask+0x90/0xb0
  [<ffffffff8102a9c9>] flat_send_IPI_all+0x69/0x70
  [<ffffffff81027372>] arch_trigger_all_cpu_backtrace+0x62/0xa0
  [<ffffffff810bff8e>] __rcu_pending+0x7e/0x370
  [<ffffffff810c02c7>] rcu_check_callbacks+0x47/0x130
  [<ffffffff81063a26>] update_process_times+0x46/0x70
  [<ffffffff81085930>] tick_sched_timer+0x60/0x160
  [<ffffffff810858d0>] ? tick_sched_timer+0x0/0x160
  [<ffffffff8107a03a>] __run_hrtimer+0xba/0x150
  [<ffffffff8107a325>] hrtimer_interrupt+0xd5/0x1b0
  [<ffffffff81426dfe>] ? trace_hardirqs_off_thunk+0x3a/0x3c
  [<ffffffff8142cacd>] smp_apic_timer_interrupt+0x6d/0x9b
  [<ffffffff8100cb33>] apic_timer_interrupt+0x13/0x20
  <EOI>  [<ffffffff811317b6>] ? mem_cgroup_walk_tree+0x156/0x180
  [<ffffffff811316d3>] ? mem_cgroup_walk_tree+0x73/0x180
  [<ffffffff81131692>] ? mem_cgroup_walk_tree+0x32/0x180
  [<ffffffff81131a00>] ? mem_cgroup_get_local_stat+0x0/0x110
  [<ffffffff81131d5b>] ? mem_control_stat_show+0x14b/0x330
  [<ffffffff810a57fd>] ? cgroup_seqfile_show+0x3d/0x60

Above shows CPU0 caught in css_tryget()'s inifinite loop because
of bad refcnt.

This is a fix to set mz=NULL at the top of retry path.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Richard Röjfors
447e4460a4 uartlite: allow building for timberdale MFD
Some configurations of the Timberdale FPGA has the uartlite
included.

Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Randy Dunlap
4932be7789 docs: update patch size in SubmittingPatches
This patch size comment is like so last millenium.  Update it to modern
times.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Albert Herranz
ed9935f4f9 sdio: pass whitelisted cis funce tuples to sdio drivers
Some manufacturers provide vendor information in non-vendor specific CIS
tuples.  For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.

This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Huang Shijie
bf89c8c867 mm/rmap.c: fix comment
The page_address_in_vma() is not only used in unuse_vma().

Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Samuel Thibault
392d814daf x86: fix csum_ipv6_magic asm memory clobber
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.

This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Mark Salter
d22a001bf6 mn10300: fix kernel build failures when using gcc-4.x
Fix some build failures when using gcc-4.x for MN10300.

Firstly, __get_user() fails to build because the pointer points to a const and
__gu_val ends up being read-only:

In file included from include/linux/mempolicy.h:62,
                 from init/main.c:50:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
make[1]: *** [init/main.o] Error 1

Secondly, gcc-4 doesn't allow casts of lvalues:

  UPD     include/linux/compile.h
arch/mn10300/kernel/rtc.c: In function 'calibrate_clock':
arch/mn10300/kernel/rtc.c:170: error: lvalue required as left operand of assignment
arch/mn10300/kernel/rtc.c:172: error: lvalue required as left operand of assignment
make[1]: *** [arch/mn10300/kernel/rtc.o] Error 1

These are seen with gcc 4.2.1.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Joe Perches
933d35f00c MAINTAINERS: ARM/Palm file patterns
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Jiri Slaby
a09efb07b5 Char: vt_ioctl, fix BKL imbalance
Stanse found (again) a BKL imbalance in vt_ioctl.

It's easily triggerable by ioctl(dev_tty_fd, VT_SETACTIVATE, NULL);

Introduced by

commit d3b5cffcf8                                 Author: Alan Cox <alan@linux.intel.com>
Date:   Sat Sep 19 13:13:26 2009 -0700

    vt: add an activate and lock

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Andrew Morton
a28b3dc909 revert "m68k: convert to asm-generic/hardirq.h"
Revert 45d80eea87 ("m68k: convert to
asm-generic/hardirq.h") - it fails to compile due to an inclusion tangle:

In file included from include/linux/irq.h:12,
                 from include/asm-generic/hardirq.h:6,
                 from /usr/src/devel/arch/m68k/include/asm/hardirq_mm.h:6,
                 from /usr/src/devel/arch/m68k/include/asm/hardirq.h:4,
                 from include/linux/hardirq.h:10,
                 from /usr/src/devel/arch/m68k/include/asm/system_mm.h:69,
                 from /usr/src/devel/arch/m68k/include/asm/system.h:4,
                 from include/linux/list.h:7,
                 from include/linux/preempt.h:11,
                 from include/linux/spinlock.h:50,
                 from include/linux/seqlock.h:29,
                 from include/linux/time.h:8,
                 from include/linux/timex.h:56,
                 from include/linux/sched.h:56,
                 from arch/m68k/kernel/asm-offsets.c:14:
include/linux/smp.h:17: error: field 'list' has incomplete type

Cc: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Mike Frysinger
b3db4a8ad1 asm-generic/gpio.h: pull in linux/kernel.h for might_sleep()
The asm-generic/gpio.h header uses the might_sleep() macro but doesn't
include the header for it, so any source code that might include
linux/gpio.h before linux/kernel.h can easily lead to a build failure.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Alexey Dobriyan
828c09509b const: constify remaining file_operations
[akpm@linux-foundation.org: fix KVM]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Andrew Morton
1c4115e595 drivers/input/input.c: fix CONFIG_PM=n warning
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used

Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Paul Mundt
3ae91c21dd module: fix up CONFIG_KALLSYMS=n build.
Starting from commit 4a4962263f "reduce
symbol table for loaded modules (v2)", the kernel/module.c build is broken
with CONFIG_KALLSYMS disabled.

  CC      kernel/module.o
kernel/module.c:1995: warning: type defaults to 'int' in declaration of 'Elf_Hdr'
kernel/module.c:1995: error: expected ';', ',' or ')' before '*' token
kernel/module.c: In function 'load_module':
kernel/module.c:2203: error: 'strmap' undeclared (first use in this function)
kernel/module.c:2203: error: (Each undeclared identifier is reported only once
kernel/module.c:2203: error: for each function it appears in.)
kernel/module.c:2239: error: 'symoffs' undeclared (first use in this function)
kernel/module.c:2239: error: implicit declaration of function 'layout_symtab'
kernel/module.c:2240: error: 'stroffs' undeclared (first use in this function)
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel/module.o] Error 2

There are three different issues:

    - layout_symtab() takes a const Elf_Ehdr

    - layout_symtab() needs to return a value

    - symoffs/stroffs/strmap are referenced by the load_module() code
      despite being ifdefed out, which seems unnecessary given the noop
      behaviour of layout_symtab()/add_kallsyms() in the case of
      CONFIG_KALLSYMS=n.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Atis Elsts
914a9ab386 net: Use sk_mark for routing lookup in more places
This patch against v2.6.31 adds support for route lookup using sk_mark in some 
more places. The benefits from this patch are the following.
First, SO_MARK option now has effect on UDP sockets too.
Second, ip_queue_xmit() and inet_sk_rebuild_header() could fail to do routing 
lookup correctly if TCP sockets with SO_MARK were used.

Signed-off-by: Atis Elsts <atis@mikrotik.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
2009-10-01 15:16:49 -07:00
Stephen Hemminger
66466797c7 sky2: irqname based on pci address
This is based on Michal Schmidt fix for skge.

Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe sky2
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered

The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ...  ie. sky2@pci:0000:00:00

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 15:14:55 -07:00
Michal Schmidt
415e69e657 skge: use unique IRQ name
Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe skge
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.

Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
 17:        169   IO-APIC-fasteoi   skge@pci:0000:00:0a.0, eth0

irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 15:14:54 -07:00
Ori Finkelman
89e95a613c IPv4 TCP fails to send window scale option when window scale is zero
Acknowledge TCP window scale support by inserting the proper option in SYN/ACK
and SYN headers even if our window scale is zero.

This fixes the following observed behavior:

1. Client sends a SYN with TCP window scaling option and non zero window scale
value to a Linux box.
2. Linux box notes large receive window from client.
3. Linux decides on a zero value of window scale for its part.
4. Due to compare against requested window scale size option, Linux does not to
 send windows scale TCP option header on SYN/ACK at all.

With the following result:

Client box thinks TCP window scaling is not supported, since SYN/ACK had no
TCP window scale option, while Linux thinks that TCP window scaling is
supported (and scale might be non zero), since SYN had  TCP window scale
option and we have a mismatched idea between the client and server
regarding window sizes.

Probably it also fixes up the following bug (not observed in practice):

1. Linux box opens TCP connection to some server.
2. Linux decides on zero value of window scale.
3. Due to compare against computed window scale size option, Linux does
not to set windows scale TCP  option header on SYN.

With the expected result that the server OS does not use window scale option
due to not receiving such an option in the SYN headers, leading to suboptimal
performance.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Signed-off-by: Ori Finkelman <ori@comsleep.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 15:14:51 -07:00
Andrew Morton
4fdb78d309 net/ipv4/tcp.c: fix min() type mismatch warning
net/ipv4/tcp.c: In function 'do_tcp_setsockopt':
net/ipv4/tcp.c:2050: warning: comparison of distinct pointer types lacks a cast

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 15:02:20 -07:00
Ralf Baechle
28ad3957b9 Kconfig: STRIP: Remove stale bits of STRIP help text
Remove references to dead web site mosquitonet.Stanford.EDU.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:49:14 -07:00
Ralf Baechle
7b1401cf5c NET: mkiss: Fix typo
This typo was introduced by 5793f4be23 on
October 14, 2005 ...

Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:48:25 -07:00
Eric Dumazet
bf18a9f8b3 tg3: Remove prev_vlan_tag from struct tx_ring_info
prev_vlan_tag field is not used.

Patch saves 512*8 bytes per tx queue ring on 64bit arches.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>
2009-10-01 14:37:34 -07:00
Uwe Kleine-König
3d1285beff move virtnet_remove to .devexit.text
The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:34:44 -07:00
Uwe Kleine-König
fb74c2fcac don't use __devexit_p to wrap sgiseeq_remove
The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:34:43 -07:00
Uwe Kleine-König
1ebb5a1aa9 don't use __devexit_p to wrap meth_remove
The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:34:40 -07:00
Jiri Pirko
ce501caf16 bonding: set primary param via sysfs
Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-01 14:34:29 -07:00
Chris Mason
9c2693c924 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable into for-linus 2009-10-01 17:24:44 -04:00
Josef Bacik
fbf1908744 Btrfs: fix data space leak fix
There is a problem where page_mkwrite can be called on a dirtied page that
already has a delalloc range associated with it.  The fix is to clear any
delalloc bits for the range we are dirtying so the space accounting gets
handled properly.  This is the same thing we do in the normal write case, so we
are consistent across the board.  With this patch we no longer leak reserved
space.

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2009-10-01 17:10:23 -04:00
David S. Miller
a98917acc7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2009-10-01 12:43:07 -07:00
Jun'ichi Nomura
b0da3f0dad Add a tracepoint for block request remapping
Since 2.6.31 now has request-based device-mapper, it's useful to have
a tracepoint for request-remapping as well as bio-remapping.
This patch adds a tracepoint for request-remapping, trace_block_rq_remap().

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:19:34 +02:00
Christoph Hellwig
67efc92580 block: allow large discard requests
Currently we set the bio size to the byte equivalent of the blocks to
be trimmed when submitting the initial DISCARD ioctl.  That means it
is subject to the max_hw_sectors limitation of the HBA which is
much lower than the size of a DISCARD request we can support.
Add a separate max_discard_sectors tunable to limit the size for discard
requests.

We limit the max discard request size in bytes to 32bit as that is the
limit for bio->bi_size.  This could be much larger if we had a way to pass
that information through the block layer.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:19:34 +02:00
Christoph Hellwig
c15227de13 block: use normal I/O path for discard requests
prepare_discard_fn() was being called in a place where memory allocation
was effectively impossible.  This makes it inappropriate for all but
the most trivial translations of Linux's DISCARD operation to the block
command set.  Additionally adding a payload there makes the ownership
of the bio backing unclear as it's now allocated by the device driver
and not the submitter as usual.

It is replaced with QUEUE_FLAG_DISCARD which is used to indicate whether
the queue supports discard operations or not.  blkdev_issue_discard now
allocates a one-page, sector-length payload which is the right thing
for the common ATA and SCSI implementations.

The mtd implementation of prepare_discard_fn() is replaced with simply
checking for the request being a discard.

Largely based on a previous patch from Matthew Wilcox <matthew@wil.cx>
which did the prepare_discard_fn but not the different payload allocation
yet.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:19:30 +02:00
Jens Axboe
6a0afdf58d drbd: remove tracing bits
They should be reimplemented in the current scheme.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:17:58 +02:00
Lars Ellenberg
ab8fafc2e1 dropping unneeded include autoconf.h
It is force-included on the gcc command line since at least 2.6.15.
Explicit include lines seem to break compilation now in certain configurations.

Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
2009-10-01 21:17:54 +02:00
Philipp Reisner
b411b3637f The DRBD driver
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
2009-10-01 21:17:49 +02:00
Jun'ichi Nomura
1a35e0f644 Add a tracepoint for block request remapping
Since 2.6.31 now has request-based device-mapper, it's useful to have
a tracepoint for request-remapping as well as bio-remapping.
This patch adds a tracepoint for request-remapping, trace_block_rq_remap().

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:16:13 +02:00
Suresh Jayaraman
3bd0f0c763 swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
While testing Swap over NFS patchset, I noticed an oops that was triggered
during swapon. Investigating further, the NULL pointer deference is due to the
SSD device check/optimization in the swapon code that assumes s_bdev could never
be NULL.

inode->i_sb->s_bdev could be NULL in a few cases. For e.g. one such case is
loopback NFS mount, there could be others as well. Fix this by ensuring s_bdev
is not NULL before we try to deference s_bdev.

Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:15:46 +02:00
Christoph Hellwig
ca80650cfb block: allow large discard requests
Currently we set the bio size to the byte equivalent of the blocks to
be trimmed when submitting the initial DISCARD ioctl.  That means it
is subject to the max_hw_sectors limitation of the HBA which is
much lower than the size of a DISCARD request we can support.
Add a separate max_discard_sectors tunable to limit the size for discard
requests.

We limit the max discard request size in bytes to 32bit as that is the
limit for bio->bi_size.  This could be much larger if we had a way to pass
that information through the block layer.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-01 21:15:46 +02:00