* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (31 commits)
avr32: Fix typo of IFSR in a comment in the PIO header file
avr32: Power Management support ("standby" and "mem" modes)
avr32: Add system device for the internal interrupt controller (intc)
avr32: Add simple SRAM allocator
avr32: Enable SDRAMC clock at startup
rtc-at32ap700x: Enable wakeup
macb: Basic suspend/resume support
atmel_serial: Drain console TX shifter before suspending
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
avr32: Use a quicklist for PTE allocation as well
avr32: Use a quicklist for PGD allocation
avr32: Cover the kernel page tables in the user PGDs
avr32: Store virtual addresses in the PGD
avr32: Remove useless zeroing of swapper_pg_dir at startup
avr32: Clean up and optimize the TLB operations
avr32: Rename at32ap.c -> pdc.c
avr32: Move setup_platform() into chip-specific file
avr32: Kill special exception handler sections
avr32: Kill unneeded #include <asm/pgalloc.h> from asm/mmu_context.h
avr32: Clean up time.c #includes
...
I have discovered that the current version of rtc-x1205.c does not work
correctly when asked to set the alarm time by the RTC_WKALM_SET ioctl()
call. This happens because the alarm registers do not behave like the
current-time registers. They are non-volatile. Two things go wrong:
- the X1205 requires a 10 msec delay after any attempt to write to the
non-volatile registers. The x1205_set_datetime() routine does the write
as 8 single-byte writes without any delay. Only the first write
succeeds. The second is NAKed because the chip is busy.
- the X1205 resets the RWEL bit after any write to the non-volatile
registers. This would lock out any further writes after the first even
with a 10msec delay.
I fix this by doing a single 8-byte write and then waiting 10msec for the
chip to be ready. A side effect of this change is that it will speed up
x1205_rtc_set_time() which uses the same code.
I have also implemented the 'enable' bit in the rtc_wkalm structure, which
the existing driver does not attempt to do. I have modified both
x1205_rtc_set_alarm() to set the AL0E bit, and x1205_rtc_read_alarm() to
return it.
I have tested this patch on a LinkSys NSLU2 under OpenWRT, but on no other
hardware. On the NSLU2 the X1205 correctly asserts its IRQ pin when the
alarm time matches the current time.
[akpm@linux-foundation.org: clean up over-parenthesisation]
Signed-off-by: Michael Hamel <mhamel@adi.co.nz>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While 0e36a9a4a7 ("rtc: fix readback from
/sys/class/rtc/rtc?/wakealarm") made sure that active alarms were never
returned with invalid "wildcard" fields (negative), it can still report
(wrongly) that the alarm triggers in the past.
Example, if it's now 10am, an alarm firing at 5am will be triggered
TOMORROW not today. (Which may also be next month or next year...)
This updates that alarm handling in three ways:
* Handle alarm rollover in the common cases of RTCs that don't
support matching on all date fields.
* Skip the invalid-field logic when it's not needed.
* Minor bugfix ... tm_isdst should be ignored, it's one of the
fields Linux doesn't maintain.
A warning is emitted for some of the unhandled rollover cases, but the
possible combinations are a bit too numerous to handle every bit of
potential hardware and firmware braindamage.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Lord <lkml@rtr.ca>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call device_init_wakeup() to signal that the RTC is capable of waking
the system. This is needed for rtcwake to work.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Mark rtc sa1100 driver as wakeup source before registering it.
rtc_device_register evaluates device_can_wakeup(rtc->dev.parent) and
supresses the creation of /sys/class/rtc/rtcX/wakealarm if
device_can_wakeup is not (yet) true.
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alarm->pending indicates whether there's an alarm that has actually been
triggered, not whether we're waiting for it. alarm->enabled indicates
that.
Also add missing locking around reading the RTC registers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This hooks up the platform-specific [gs]et_rtc_time functions so that
kernels using CONFIG_RTC_CLASS have RTC support on most PowerPC platforms.
A new driver, and one which we've been shipping in Fedora for a while
already, since otherwise RTC support breaks.
[akpm@linux-foundation.org: fix Kconfig indenting]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the name of the device from "rtc-ds1374" to just "ds1374", to match
what all other RTC drivers do. I seem to remember that this name was
chosen to avoid possible confusion with an older ds1374 driver, but that
driver was removed 3 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the help text for RTC_DRV_AT91SAM9 to mention that the
option apply to AT91CAP9 processors too, and enable it in the
defconfig.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the two functions rtc-sa1100 wants from the old ARM RTC library
into the rtc-sa1100 driver.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ARM, asm/rtc.h only contains definitions for the predecessor to
the RTC class support. RTC class drivers should not be including
this include.
Build tested on at91sam9rl and s3c2410 configurations.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert Integrator PL030 RTC driver to use the RTC class interfaces.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up PL031 RTC includes, make driver use proper resource checking,
and use amba bus specific accessors.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/mach/time.h is the ARM header file for setting up kernel ticker
timekeeping (be that the old jiffy interrupt or the new clocksource.)
RTC drivers have no business using this header file, and in fact do
not require it.
Build tested on at91sam9rl, omap and s3c2410 configurations.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver uses printk(), but does not include <linux/kernel.h> -- add it.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Watchdog handlers within the driver make use of "save_client" -- make sure it
has been initalized before the handlers are registered.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The input argument to rtc_time_to_tm() is unsigned as well as are members of
the output structure. However signed arithmetic is used within for
calculations leading to incorrect results for input values outside the signed
positive range. If this happens the time of day returned is out of range.
Found the problem when fiddling with the RTC and the driver where year was set
to an unexpectedly large value like 2070, e.g.:
rtc0: setting system clock to 2070-01-01 1193046:71582832:26 UTC (3155760954)
while it should be:
rtc0: setting system clock to 2070-01-01 00:15:54 UTC (3155760954)
Changing types to unsigned fixes the problem.
[akpm@linux-foundation.org: remove old-fashioned `register' keyword]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the old driver_name/type matching scheme is going away soon, change
the dummy device mechanism to use the new matching scheme.
This has the downside that dummy i2c clients can no longer choose
their name, they'll all appear as "dummy" in sysfs and in log
messages. I don't think it is a problem in practice though, as there
is little reason to use these i2c clients to log messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (37 commits)
SH: catch negative denormal_subf1() retval in denormal_add()
sh: Fix DMAC base address for SH7709S
sh: update smc91x platform data for se7206.
sh: Stub in cpu_to_node() and friends for NUMA build.
sh: intc register modify fix
sh: no high level trigger on some sh3 cpus
sh: clean up sh7710 and sh7720 intc tables
sh: add interrupt ack code to sh3
sh: unify external irq pin code for sh3
sh-sci: avoid writing to nonexistent registers
sh-sci: sh7722 lacks scsptr registers
sh-sci: improve sh7722 support
sh: reset hardware from early printk
sh: drain and wait for early printk
sh: use sci_out() for early printk
sh: add memory resources to /proc/iomem
sh: add kernel bss resource
sh: fix sh7705 interrupt vector typo
sh: update smc91x platform data for se7722
sh: update smc91x platform data for MigoR
...
The file in drivers/rtc/rtc-ds1551.c uses "int" for flags. This can cause
hard to find bugs on some architectures. This patch converts the flags to use
"long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pnp_resource_table is going away soon, so use the more
generic public interfaces instead.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current kernel if we want to set the alarm time, the absolute time the
seconds relative to 1970-01-01 00:00:00) should be written into
/sys/class/rtc/rtc0/wakealarm. It is not convenient.
It is more reasonable to add the support for the alarm time relative to
current RTC time.(the unit is second)
For example:
If the RTC is required to generate alarm after 2 minutes, the following
will be OK.
echo +120 > /sys/class/rtc/rtc0/wakealarm
or echo +0x78 > /sys/class/rtc/rtc0/wakealarm
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rs5c_get_regs() currently uses rs5c->rtc->name for its debug printk when
i2c_transfer() fails, though it is used several times before the rtc dev
has been registered. The earliest we can get at the symbolic name is via
the i2c client's struct device, which can be handled by moving the first
rs5c_get_regs() until after the client pointer is assigned.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the needlessly global ds1511_rtc_{read,set}_time() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.data+0x253e28): Section mismatch in reference from the variable test_drv to the function .devexit.text:test_remove()
Fix by renaming the platfrom_driver variable from *_drv to *_driver
so modpost ignore the reference to an __devexit section.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kconfig tweaks to help reduce RTC configuration bugs, by avoiding
legacy RTC drivers when the generic RTC framework is enabled:
- If rtc-cmos is selected, disable the legacy rtc driver;
- When using generic RTC on x86, enable rtc-cmos by default;
- In the old "chardev RTC" section of Kconfig, add a comment
warning people off these (seven) legacy RTC drivers when
the generic framework is in use.
People can still use the legacy drivers if they want (or need) to.
This doesn't fix the broken dependencies for the legacy "CMOS" RTC driver.
Ideally it would be a full list of platforms where it works, not a partial
list of ones where it won't. Or better yet, it would depend on a
"HAVE_CMOS_RTC" flag defined by various platforms ... surely there's a
Kconfig style guideline lurking there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bogus #include in rtc-pcf8583, so it compiles on platforms that
don't support PC clone RTCs. (Original issue noted by Adrian Bunk.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Adrian Bunk <bunk@kernel.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for periodic IRQs to the rtc-sh driver.
RTC_IRQP_READ/RTC_IRQP_SET are added, with a number of other fixes and
reordering across the rest of the code.
Signed-off-by: Angelo Castello <angelo.castello@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is a bug in the function of cmos_set_alarm. RTC alarm time for October
can't be set correctly.
For October: 0x0A will be written into the RTC region (MONTH_ALARM) in current
kernel. But in fact 0x10 should be written. Wildcards are also not handled
correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable RTC
platform drivers, to re-enable module auto loading.
[dbrownell@users.sourceforge.net: more drivers, minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-s35390a uses BITREVERSE functions so it needs to select that config symbol
to ensure that the functions are built.
drivers/built-in.o: In function `s35390a_set_datetime':
linux-2.6.25-rc8-git7/drivers/rtc/rtc-s35390a.c:144: undefined reference to `byte_rev_table'
drivers/built-in.o: In function `s35390a_get_datetime':
linux-2.6.25-rc8-git7/drivers/rtc/rtc-s35390a.c:163: undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates to the at91sam9 rtt-as-rtc driver:
- Bugfix: IRQ enable bits need shifting before masking with status
- Platform code to initialize wakeup bits didn't get merged; cope
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Justin Waters <justin.waters@timesys.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds basic get/set time support for the Seiko Instruments S-35390A.
This chip communicates using I2C and is used on the QNAP TS-109/TS-209 NAS
devices.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <david-b@pacbell.net>
Tested-by: Tim Ellis <tim@ngndg.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect. Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AT91sam9 RTC support, primarily in the form of an RTT-as-RTC driver that was
extracted from 2.6.23-at91 patch and updated:
- Relies on now-merged platform updates, which associate the RTT
hardware address with each RTT and use the "at91_rtt" name.
- RTC framework related fixes and cleanups, notably:
* removed now-needless suspend/resume clock offset logic
* alarm read/write now respects the "enabled" flag
* suspend always disables update irqs
* shutdown (and startup) disables all irqs
- Misc cleanup:
* use dev_*() messaging
* add comments
* remove globals,
* ... etc
- Don't force use of RTT0 and GPBR0. Either resource may need
to be used for other purposes (like NO_HZ support).
- Update "AT91RM9200 RTC" Kconfig to allow it on SAM9RL chips
(it has both RTT and RTC).
Driver binding uses bus_find_device() to avoid needing any kind of "timer
library" code when there's more than one RTT module. (This timer can be used
as an RTC, to support NO_HZ operation, or potentially for other stuff. The
choice is a per-system policy.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michel Benoit <murpme@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some more references to dev->power.power_state. That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For DS140, clear the oscillator fault flag as needed.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
[ And remove some "sparse" warnings. ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Epson RTC-9701JE SPI RTC device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Epson RTC-9701JE SPI RTC device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That patch adds the RTC emulation of the HPET timer to the new RTC_DRV_CMOS.
The old drivers/char/rtc.ko driver had that functionality and it's important
on new systems.
[akpm@linux-foundation.org: unbreak alpha build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- thus clearing out the need for spin locks
- add a small optimization for reading of the rtc field
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
also, dont bother using memcpy since we can just do an assignment of the same structure.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start making the rtc-cmos alarm act more like a oneshot alarm by disabling
that alarm after its IRQ fires. (ACPI hooks are also needed.)
The Linux RTC framework has previously been a bit vague in this area, but
any other behavior is problematic and not very portable. RTCs with full
YYYY-MM-DD HH:MM[:SS] alarms won't have a problem here. Only ones with
partial match criteria, with the most visible example being the PC RTC, get
confused. (Because the criteria will match repeatedly.)
Update comments relating to that oneshot behavior and timezone handling.
(Timezones are another issue that's mostly visible with rtc-cmos. That's
because PCs often dual-boot MS-Windows, which likes its RTC to match local
wall-clock time instead of UTC.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a basic ds1302 RTC driver, which is basically a cleanup and move
of the in-tree SH SecureEdge5410 code (which is currently located in
arch/sh/board/snapgear/rtc.c) to drivers/rtc.
This aims to be a building block that the M32R and CRIS code can be worked
on top of, so we can get rid of drivers/char/ds1302.c and
arch/cris/arch-v10/drivers/ds1302.c respectively, though more work is
needed for this.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes rtc-cmos export its NVRAM, like several other RTC drivers.
It still works within the limits of the current CMOS_READ/CMOS_WRITE calls,
which don't understand how to access multiple register banks. The primary
impact of that limitation is that Linux can't access the uppermost 128
bytes of NVRAM on many systems.
Note that this isn't aiming to be a drop-in replacement for the legacy
/dev/nvram support. (Presumably that has real users, and isn't just
getting carried forward automatically?) Userspace handles more work:
- When userspace code updates NVRAM, that will need to include
updating any platform-specific checksums that may apply.
- No /proc/driver/nvram file will parse and display NVRAM data
according to whichever boot firmware your board expects.
Also minor pnp-related updates: update a comment, remove dead code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use is_power_of_2() macro for simplicity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-pcf8583 driver is using the I2C_M_NOSTART flag but shouldn't. This
flag is only meant for broken chips and the PCF8583 RTC chip is not one of
these.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add adds a warning if a potentially conflicting RTC option has been
selected and makes some other cosmetic fixes to the Kconfig.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
With all of the different CPU types this was getting a but unwieldly.
Since sh64 is now integrated, we don't have to worry about multiple
architectures caring about the header definitions.
Split out the defs for each asm/cpu/ to make rtc-sh slightly less
visually offensive.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace wakeup support using the alarm via the SA1100 RTC driver on
SA1100 and PXA platforms. This allows RTC alarm wakeup to be enabled
via sysfs using the conventional attributes.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert to use the class iteration api.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reorder at32_rtc_probe() so that it's safe (no oopsing) to fire the
IRQ handler the instant that it's registered. (Bug noted via "Debug
shared IRQ handlers" kernel debug option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <hcegtvedt@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e. that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.
Spotted by Nick Piggin.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC code is using mutex to assure exclusive access to /dev/rtc. This is
however wrong usage, as it leaves the mutex locked when returning into
userspace, which is unacceptable.
Convert rtc->char_lock into bit operation.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the NVRAM on DS1307 and DS1338 chips, like several of the
other drivers do for such combination RTC-and-NVRAM chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the RTC drivers are exporting binary "nvram" files in sysfs. Such
NVRAM (or on many systems, EEPROM) data is often initialized during system
manufacture to hold data about identity (serial numbers, Ethernet addresses,
etc), configuration, calibration, and so forth.
This patch improves integrity and security of those files:
- Correctly initializes the size in one of the two cases where
that was not yet being done.
- Improves system security/integrity by making this state not
be world-writable by default.
Letting arbitrary userspace code mangle such state by default is at least Not
A Good Thing; and it could sometimes be worse, depending on the particular
data that might be corrupted. (I disregard the paranoiac "don't let anyone
read it either" approach. Anyone storing passwords in such memory doesn't
really care about security.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Torsten Ertbjerg Rasmussen <tr@newtec.dk>
Cc: Mark Zhan <rongkai.zhan@windriver.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC "hctosys" mechanism expects that RTC clock will use UTC, not local
time (e.g. PST). Say so in Kconfig and in the kernel message.
(Strictly speaking, the RTC clock should be tracking the POSIX epoch. That's
not worth going into here. Goofing timezones means clocks are wrong by many
hours; the POSIX-v-UTC differences just cost seconds.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Follows the changes of some of the other RTC drivers. If the tm
value is bogus, just zero it out. Adds some sanity for RTC_RD_TIME.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently if rtc_device_register() fails we have an IS_ERR() on
the wrong pointer, which causes this to always be skipped. Fix
this up to actually check the right pointer. The return value
was always correct, even though the check was wrong.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Change the name of this data to use a name (suffix) that is whitelisted
by MODPOST so that the section warning is fixed (not generated).
WARNING: vmlinux.o(.data+0x1b140): Section mismatch: reference to .init.text:m48t59_rtc_probe (between 'm48t59_rtc_platdrv' and 'm48t59_nvram_attr')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a system here that actively relies upon RTC wake alarms, and it
has been failing (again) for a few days when attempting to use the
/sys/class/rtc/rtc?/wakealarm interface.
The old (fixed by Linus) /proc/ interface still works, but I'd like to
get it using the new one.
This patch fixes rtc-cmos to ignore the two upper bits when reading the
BCD mday (day of month) register from CMOS. Some systems (eg. mine)
seem to have the top bit set to "1" for some reason.
The older /proc/ interface ignores the upper bits, and so we should too.
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/rtc.c allowed RTC_PIE_ON ioctls for non-root users, as long as
the current interval (set via RTC_IRQP_SET) is <= max_user_freq. Allow
RTC_PIE_ON under the same conditions when /dev/rtc* is handled by the rtc
subsystem.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/rtc.c exposed a sysctl to change the maximum frequency at
which a non-root user could ask the RTC to generate interrupts (via the
RTC_IRQP_SET ioctl). This value is no longer available under the new RTC
subsystem, so add it to sysfs for each RTC device.
Works for me on x86_64 (both reads and writes), using rtc-cmos.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some cleanups for the rtc-cmos probe logic:
- Claim i/o ports with request_region() not request_resource(),
for better coexistence betwen platform and pnp bus glues.
- Claim those ports earlier, to help work around procfs bugs
(it allows duplicate names, like /proc/driver/rtc).
- Fix some glitches in cleanup code, notably a cut'n'paste-o
where the i/o port region might not get released during
cleanup after a probe fault.
And some comment clarifications, including noting that this code
must work with PNPBIOS not just PNPACPI..
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix readback of RTC alarms on platforms which return -1 in
non-hardware-supported RTC alarm fields.
To fill in the missing (-1) values, we grab an RTC timestamp along with the
RTC alarm value, and use the timestamp fields to populate the missing alarm
fields.
To counter field-wrap races (since the timestamp and alarm are not read
together atomically), we read the RTC timestamp both before and after
reading the RTC alarm value, and then check for wrapped fields --> if any
have wrapped, we know we have a possible inconsistency, so we loop and
reread the timestamp and alarm again.
Wrapped fields in the RTC timestamps are an issue because rtc-cmos.c, for
example, also gets/uses an RTC timestamp internally while fetching the RTC
alarm. If our timestamp here wasn't the same (minutes and higher) as what
was used internally there, then we might end up populating the -1 fields
with inconsistent values.
This fixes readbacks from /sys/class/rtc/rtc?/wakealarm, as well as other
code paths which call rtc_read_alarm().
Signed-off-by: Mark Lord <mlord@pobox.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an RTC class driver for the Maxim/Dallas 1374 RTC chip,
based on drivers/i2c/chips/ds1374.c. It supports alarm functionality.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all i2c adapters support I2C-level messaging. Check that the adapter
does before probing for a PCF8583 chip, as the driver makes use of
i2c_transfer and i2c_master_send.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1553 platform driver name doesn't match its module name, which
might prevent it from properly hotplugging. This driver has no in-tree
users.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In rtc-dev.c, when a rtc device is opened, file->private_data is already
attached with the rtc device pointer, so there is no need to call
to_rtc_device() to convert file->private_data to a rtc device pointer.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC periodic IRQs are only defined to work for 2^N Hz values. This patch
moves that validity check into the infrastructure, so drivers don't need to
check it; and adds kerneldoc for the two interface functions related to
periodic IRQs. (One of which was quite mysterious until its first use was
recently checked in!)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add kernel/kernel and kernel/user locking for the periodic irq feature of
the rtc class.
PIE ioctls are also supported.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently the rtc driver, rtc-ds1552.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC. This breaks on 32-bit systems with
larger physical addresses.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the rtc driver, rtc-ds1742.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC. This breaks on systems like PowerPC
440, which is a 32-bit core with 36-bit physical addresses: IO on the
system, including the RTC, is typically above the 4GB point, and cannot fit
into an unsigned long.
This patch fixes the problem by replacing the unsigned long with a
resource_size_t. Tested on Ebony (PPC440) (with additional patches to
instantiate the ds1742 platform device appropriately).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches. This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new rtc-m41t80 driver name doesn't match its module name, which
prevents it from properly hotplugging. Since it's new, no platforms yet
depend on that name ... so this patch fixes the driver name to match its
module name, rather than going the other way around with a MODULE_ALIAS().
NOTE: This sort of bug is a new thing to watch out for with new-style I2C
drivers; previously I2C couldn't hotplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since irq in m48t59_private struct is defined as 'unsigned int', which will
make the following if sentence to be never true:
if (m48t59->irq < 0)
m48t59->irq = NO_IRQ;
And thus it will make the m48t59_rtc_probe() is failed when the driver is
working in a no irq mode:
Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so that the
user can disable the whole feature without having to enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent the RTC driver from returning ENOIOCTLCMD to userspace.
Signed-off-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the changes from moving around the arch support for s3c24xx based
systems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
sh: Fix fs.h removal from mm.h regressions.
sh: fix get_wchan() for SH kernels without framepointers
sh: arch/sh/boot - fix shell usage
rtc: rtc-sh: Correct sh_rtc_set_time() for some SH-3 parts.
sh: remove support for sh7300 and solution engine 7300
sh: Add sh to the CC_OPTIMIZE_FOR_SIZE dependencies.
sh: Kill off virt_to_bus()/bus_to_virt().
sh: sh-sci - fix SH7708 support
sh: Restrict DSP support to specific CPUs.
sh: Silence sq compile warning on sh4 nommu.
sh: Kill the rest of the SE73180 cruft.
sh: remove support for sh73180 and solution engine 73180
sh: remove old broken pint code
sh: Reclaim beginning of P3 space for vmalloc area.
sh: Fix Dreamcast DMA issues.
sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
Alphabetic reordering of the drivers in the rtc subsys makefile.
(akpm: merge this asap! Makefiles are the source of many patch conflicts..)
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo turned up by a Coverity check: referring to the wrong register,
which could cause problems with DS1338 RTCs whose oscillators halted.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct bin_attribute * is needed in bin_attribute ->read()/->write()
now. Incidentally, could people please run the fscking compiler
before and after applying their patch and compare the build logs?
That (and many, many other) would be caught immediately.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SH-3 parts (SH7720 and SH7705 at least) need to have the
start bit explicitly cleared, as the reset is not enough. This
is safe across all parts, so simply clear the start bit in
the sh_rtc_set_time() path.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This avoids use of the kernel-internal "xtime" variable directly outside
of the actual time-related functions. Instead, use the helper functions
that we already have available to us.
This doesn't actually change any behaviour, but this will allow us to
fix the fact that "xtime" isn't updated very often with CONFIG_NO_HZ
(because much of the realtime information is maintained as separate
offsets to 'xtime'), which has caused interfaces that use xtime directly
to get a time that is out of sync with the real-time clock by up to a
third of a second or so.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the Simtek STK17TA8 timekeeping chip.
The STK17TA8 is quite similar to the DS1553, but differs in register layout
and in various control bits in the registers. I chose to make this a new
driver to avoid confusion in the code and to not get lost in #ifdefs.
Signed-off-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now read and write the century byte in the max6900 chip. We probably
don't need to do so on Linux-only system, but it's necessary when the chip
is shared by another OS that uses the century byte.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various people have expressed surprise that their modular RTC drivers don't
seem to work for initializing the system time at boot. To help avoid such
unpleasantness, make the Kconfig text point out that the driver probably
needs to be statically linked.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both shwdt and rtc-sh are only supported on SH-3 and SH-4 at
the moment, don't allow them to break the SH-2 and SH-5 (sh64)
builds.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds support for periodic irq enabling in rtc-cmos. This could be used by
the ALSA driver and is already being tested with the zaptel ztdummy module.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Texas Instruments TWL92330/Menelaus Power Management chip driver. This
includes voltage regulators, Dual slot memory card tranceivers and
real-time clock(RTC).
The support for RTC is integrated with this driver only; it is not separate
module. Passes 'rtctest' on OMAP H4 EVM, other than lack of "periodic"
(1/N second) IRQs. System wakeup alarms (from suspend-to-RAM) work too.
The battery keeps the RTC active over power off, so once you set clock
(rdate/ntpdate/etc, then "hwclock -w") then RTC_HCTOSYS at boot time will
behave as expected.
Cc: "Jean Delvare" <khali@linux-fr.org>
Cc: "Tony Lindgren" <tony@atomide.com>
Cc: "David Brownell" <david-b@pacbell.net>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the rtc-ds1307 driver into a "new style" driver.
Also improve probe() checks: be more correct about switching out of
AM/PM mode, and issue a (debug) diagnostic when failing due to bogus
register values.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we find a ds1337 or ds1339 with the oscillator powered off, turn it
on. If the oscillator fault flag was set, clear it and warn that the clock
needs to be set.
David Brownell: Bugfixes; provide corresponding update for ds1338, and the
core of the fix for ds1340. Use a common warning message ("SET TIME!")
whenever the clock needs to be set after oscillator fault (or oscillator
enable, if fault is not a separate status).
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a watchdog driver interface to rtc-m41t80 driver. This is derived from
works by Alexander Bigga <ab@mycable.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Alexander Bigga <ab@mycable.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new-style i2c driver for ST M41T80 series RTC chip, derived from
works by Alexander Bigga <ab@mycable.de> who wrote the original
rtc-m41txx.c based on drivers/i2c/chips/m41t00.c driver.
This driver supports M41T8[0-4] and M41ST8[457]. The old m41t00 driver
supports M41T00, M41T81 and M41T85(M41ST85). While the M41T00 chip is now
supported by rtc-ds1307 driver, this driver does not include support for
the chip.
[akpm@linux-foundation.org: remove bogus `static']
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Alexander Bigga <ab@mycable.de>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fix to the Kconfig for RTCs: don't display section headers for I2C or
SPI unless they're configured. And depend on SPI_MASTER; having slave
support wouldn't help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested on the AT32AP7000/ATSTK1000. Driver does only suport time, wake up
and a very simple alarm, because of hardware limitations.
Hardware documentation can be found in the AT32AP7000 data sheet, which can
be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
From: David Brownell <david-b@pacbell.net>
- Strike some alarm setup code that's no longer needed.
(This patch seems to have gotten lost somewhere...)
- Make the driver name (and its module alias) match what
the platform setup code uses, so the driver can bind
and hotplug.
[akpm@linux-foundation.org: fix several checkpatch.pl warnings]
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert rtc-rs5c372 to be a "new style" I2C driver, and update the
Kconfig text to be more complete..
Verified on an OMAP H4 development platform, along with a board
init patch to declare its rv5c387a device.
Only one defconfig -- powerpc/linkstation -- uses this driver; but
several other platforms use it, just without defconfig support.
Such platforms need to be converted so (a) their I2C adapter driver
supports new-style drivers, and (b) board init code declares this
I2C device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Voipio Riku <Riku.Voipio@movial.fi>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the rtc-ds1307 driver so that converting it to a "new style"
driver (driver model, not legacy i2c model) will involve fewer changes.
- Use pointer to i2c_client almost everywhere, so that it's easy
to let the i2c core create that object;
- Avoid using i2c_client.adapter, since that field is redundant and
thus may go away (same object as i2c_client.dev.parent).
- Extend type enum to include various RTCs this is expected to
work with, and include register support for them.
It also cleans up the support for multiple chip types, and fixes a
glitch that could appear with an un-initialized RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
