New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bbt structure isn't actually used, just the badblockpos. This lets
the driver correctly handle badblocks with the different OOB layout with
certain sized flashes. Previously, the blocks would all be reported as
bad and be completely unusable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since info->mtd isn't dynamically allocated, we shouldn't attempt to
kfree() it. Otherwise we get random fun corruption when unloading
the driver built as a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Seems some patches got out sync when being merged. The Blackfin NFC
driver was updated to use nand_scan_ident(), but it missed the change
where nand_scan_ident() now takes 3 arguments. So update this driver
to fix build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The IRQSTAT register is a W1C register used by the interrupt handler and
may have its BUSY bit changed. This makes it somewhat unreliable for the
polling devready function. So switch it over to use the BUSY bit in the
STAT register that always reflects the current state of the hardware.
This fixes driver hangs seen when the NAND flash is under heavy system
load (like I/O benchmarks).
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rather than forcing the platform resources to declare the desired page
size, simply use the existing information passed down to us by the higher
layers. This way we work out of the box with all flash chips that the
kernel knows about.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When resetting the ECC registers/counters, the bit will automatically
clear itself once the reset has actually finished. So make sure we
wait for that to occur before doing anything else rather than assuming
everything is peachy and proceeding with stale ECC values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We used the platform rd_dly field when we meant to use the wr_dly field.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND base may send some controls which are neither CLE nor ALE, so
we need to explicitly check both instead of assuming things are always
one or the other. Otherwise, we sometimes send out illegal addresses
to the NAND device.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Our write_buf/read_buf funcs always do ECC in HW ECC mode. That is not
needed for raw funcs. In fact, write_buf/read_buf should be a pure func
for data input/output while chip->ecc.hwctl controls ECC. Unfortunately,
we can't separate ECC from normal data input/output in our NFC, so our DMA
write_buf/read_buf entries are coupled with ECC operations closely.
Thus we need to provide dedicated read_page_raw/write_page_raw funcs where
we do non-DMA transactions so as to avoid automatic ECC.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The low level NAND driver doesn't care about filesystems, so punt the
local comment indicating otherwise.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all magic numbers into appropriate defines, and move the defines
out of the global namespace and into this one driver. No other driver
needs to care about the MMR layout anyways.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The DMAs have different bit sizes on BF52x and BF54x. From the PHRM:
"The 16-bit DMA Access Bus (DAB) connects the DMA controller to the
on-chip peripherals, PPI, SPI, Ethernet MAC, the SPORTs, NFC,
HOSTDP and the UARTs."
32-bit DMA won't work for BF52x.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The bf5xx_nand_add_partition() func is only called by __devinit functions,
so put it into the __devinit section as well
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only set DMAC1_PERIMUX once we have requested and been granted the dma
channel to prevent breaking other peripherals in the error case
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.
NOTE: at91_nand for some reason disallows modular builds. I'm assuming that's
just an oversight that will be fixed.
[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
There is no suspend/resume operation in NFC driver at all, currently.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
