The SIOCGIWFREQ ioctl fills the request structure's freq field by setting
the exponent to 0 and the mantissa to the current channel number. The
iwconfig tool works around this behaviour by looking up the frequency
from the channel table if a frequency below 1kHz is returned, other tools
(e.g. kwlaninfo) don't. According to the comment in the iwconfig source
the driver is supposed to return the frequency, not the channel number.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving part of the debugging code from IPW_DEBUG to IPW_LL_DEBUG (low level
debugging) and make IPW_DEBUG be always enabled. IPW_LL_DEBUG still needs
to be enabled by selecting CONFIG_IPW2200_DEBUG. But it is highly
deprecated for normal users since it adds higher debug verbosity in driver
hot paths.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hard_start_xmit should return a NETIF_TX_FOO error code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the bitfields in the bcm43xx DMA code to properly
aligned u8 booleans. These flags are accessed in the DMA
hotpath, so it's a good idea to waste a few bytes of memory
for the sake of speed by not requiring masking (and probably
shifting) of the bitfields.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't rely on linux/if_arp.h being included by other headers
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SPARC architecture has been fixed, so it's no longer needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calls to bcm43xx_rng_init() and bcm43xx_rng_exit() got
lost due to merge trouble. Re-add them.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rewrite of the bcm43xx DMA engine. It adds support
for >1G of memory (for chips that support the extension bits)
and 64-bit DMA (for chips that support it).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The airo driver is currently caching a pid for later use, but with the
implementation of containers, pids themselves do not uniquely identify a
task. The driver is also using kernel_thread() which is deprecated in
drivers.
This patch essentially replaces the kernel_thread() with kthread_create().
It also stores the task_struct of the airo_thread rather than its pid.
Since this introduces a second task_struct in struct airo_info, the patch
renames airo_info.task to airo_info.list_bss_task.
As an extension of these changes, the patch further:
- replaces kill_proc() with kthread_stop()
- replaces signal_pending() with kthread_should_stop()
- removes thread completion synchronisation which is handled by
kthread_stop().
[akpm@osdl.org: fix races]
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Javier Achirica <achirica@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code that reads part_num from the EEPROM. This part number
is never displayed or queryable by the user.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: We
should free resources allocated for previous rings if following allocation
fails.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
irq leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: if
e1000_up fails in e1000_open() we do not free allocated irq
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unlike the other tty comment patch this one has code changes. Specifically
it limits the queue size for a tty to 64K characters (128Kbytes) worst case
even if the tty is ignoring tty->throttle. This is because certain drivers
don't honour the throttle value correctly, although it is a useful
safeguard anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doesn't fix them but does show up some interesting areas that need review
and fixing.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix printk format warning:
drivers/cdrom/gscd.c:269: warning: format â%luâ expects type âlong unsigned intâ, but argument 2 has type âunsigned intâ
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
None of the other /proc/meminfo lines have a space in the identifier. This
post-2.6.17 addition has the potential to break existing parsers, so use an
underscore instead (like Committed_AS).
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
idescsi_pc_intr() uses local_irq_enable() in IRQ context: annotate it.
(this has no effect on kernels with lockdep disabled. On kernels with lockdep
enabled this means that we wont actually disable interrupts, and the warning
message will go away as well.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent patch broke the ability to do a user-request check of a raid1.
This patch fixes the breakage and also moves a comment that was dislocated
by the same patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we
- shut down a clean array,
- restart with one (or more) drive(s) missing
- make some changes
- pause, so that they array gets marked 'clean',
the event count on the superblock of included drives
will be the same as that of the removed drives.
So adding the removed drive back in will cause it
to be included with no resync.
To avoid this, we only update the eventcount backwards when the array
is not degraded. In this case there can (should) be no non-connected
drives that we can get confused with, and this is the particular case
where updating-backwards is valuable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent hwctrl core conversion for MTD NAND devices broke the Amstrad
Delta driver. This fixes it up and uses the existing control line defines
rather than unclear magic numbers.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When reading /dev/vcsa while a font with more than 256 characters is
loaded, one of the attribute bits records the 9th bit of the character.
But depending on the console driver (vgacon or fbcon for instance), that's
bit 3 or bit 0. And there is no way for userland to know that, thus no way
for userland to safely grab the screen content. So here is a (tested)
patch:
Add a VT_GETHIFONTMASK ioctl for knowing which bit is the 9th bit for VC
text (vc_hi_font_mask field of the vc_data structure).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I wish I was happier about this patch. It'll serve as a placeholder for
the moment. I'm still trying to get a G550 working in order to even
reproduce the problem this patch introduces. I find that the G450 has
jitter even without this patch, so it won't show me what the patch changed.
At this point, I'll continue trying to get the G550 to work, and in
parallel work with the G450 to work out the kinks.
The patch is below.
Set XDVICLKCTRL only on PPC, as doing this apparently introduces jitter on
the G550, at least on x86 architectures.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While testing Moxa C218T/PCI on PowerPC 405EP I found that loading firmware
using the linux kernel driver fails because calculation of the checksum is
not endianess independent in the original code.
After I fixed this I found that uploading firmware in a system with
multiple cards causes a kernel oops. I had a look in the recent moxa
sources and found that they do some kind of locking there. Applying this
lock fixed the problem.
Alan sayeth:
Checksum changes are clearly correct. Other changes is an improvement but
not I think enough to handle malicious firmware attacks. That said such an
attacker has CAP_SYS_RAWIO anyway so that part is irrelevant except for
neatness.
[akpm@osdl.org: cleanups]
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the return value before we release the nand device otherwise the
value can become corrupted by another user of chip->ops, ultimately
resulting in filesystem corruption.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recently a patch was added for preliminary suspend/resume handling on
!PPC_PMAC. However, this broke both suspend and firewire on powerpc
because it saves the pci state after the device has already been disabled.
This moves the save state to before the pmac specific code.
Signed-off-by: Danny Tholen <obiwan@mailmij.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When cdev_add() failed there is no reason to call cdev_del().
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the year check on setting the time with the S3C24XX RTC driver. Also
move the debug to before the set to see what is going on if it does fail.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On an nForce4-equipped machine with two SATA disk in raid1 setup using dmraid,
we experienced frequent deadlock of the system under high i/o load. 'cat
/dev/zero > ~/zero' was the most reliable way to reproduce them: Randomly
after a few GB, 'cp' would be left in 'D' state along with kjournald and
kmirrord. The functions cp and kjournald were blocked in did vary, but
kmirrord's wchan always pointed to 'mempool_alloc()'. We've seen this pattern
on 2.6.15 and 2.6.17 kernels. http://lkml.org/lkml/2005/4/20/142 indicates
that this problem has been around even before.
So much for the facts, here's my interpretation: mempool_alloc() first tries
to atomically allocate the requested memory, or falls back to hand out
preallocated chunks from the mempool. If both fail, it puts the calling
process (kmirrord in this case) on a private waitqueue until somebody refills
the pool. Where the only 'somebody' is kmirrord itself, so we have a
deadlock.
I worked around this problem by falling back to a (blocking) kmalloc when
before kmirrord would have ended up on the waitqueue. This defeats part of
the benefits of using the mempool, but at least keeps the system running. And
it could be done with a two-line change. Note that mempool_alloc() clears the
GFP_NOIO flag internally, and only uses it to decide whether to wait or return
an error if immediate allocation fails, so the attached patch doesn't change
behaviour in the non-deadlocking case. Path is against current git
(2.6.18-rc4), but should apply to earlier versions as well. I've tested on
2.6.15, where this patch makes the difference between random lockup and a
stable system.
Signed-off-by: Daniel Kobras <kobras@linux.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the cleanups of drivers/rtc/s3c-rtc.c, the base address for the
registers got broken. This patch fixes that by ensuring the readb/writeb
are all prefixed with the base returned from ioremap()ing the registers.
Also fix check for valid year range, which was the wrong way around.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.
Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range. It matches at least one device that doesn't
respond to the initialization sequence. Perhaps the sequence needs to
be updated, or perhaps something else can be done. For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.
This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for a clone of Nokia DKU-5 cable made by Ours
Technology Inc, as it turned out that the cable does not use the pl2303
chip, but OTI-6858 chip which is not compatible with the pl2303.
Signed-off-by: Tomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was pointed out by Adrian Bunk <bunk@stusta.de>, as found by the Coverity Checker.
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes an unused kerneldoc entry from pci_match_device and
put the others into correct order.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch against the CPCI hotplug core to fix up PCI resource
assignment such that things will actually work when a hot inserted
device is enabled. I mentioned this patch to you way back in April at
ELC, but am only now out from under things enough to clean it up and
submit it. I've basically cribbed the corresponding code from
shpchp_pci.c, so there are no big surprises. If it's still possible, I
wouldn't mind this going into 2.6.18, but it wouldn't be the end of the
world if it went into 2.6.19.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add the ICH6(R) LPC to the ICH6 ACPI quirks. currently only the ICH6-M
is handled. [ PCI_DEVICE_ID_INTEL_ICH6_1 is the ICH6-M LPC, ICH6_0 is
the ICH6(R) ]
- remove the wrong quirk calling asus_hides_smbus_lpc() for ICH6. the
register modified in asus_hides_smbus_lpc() has a different meaning in
ICH6.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains 2 sets of fixes for the abituguru:
1) Much improved timeout handling, drasticly reducing the amount of
timeout errors on some motherboards
2) Fix the exit paths in the bank1 sensor type detect code to always
restore the original settings even on an error. Without this our
special test settings could remain seriously confusing the system
BIOS's setup menu.
Both are very much related and are must haves, to avoid messing up the
uguru CMOS settings.
Detailed changes:
- Much improved timeout / wait for status handling. Many thanks to Sunil
Kumar, for all his testing, ideas and patches! The code now first busy
waits, polling the uguru for the expected status as this usually
succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn
in timeout conditions, the amount of busy waiting has been halved from
previous versions (120 tries instead of 250). This is not a problem,
because this version goes to sleep after 120 attemps for 1 jiffy and
then tries again, it does this sleep and try again 5 times before
finally giving up. This (almost?) completly removes the timeout errors
some people have seen regulary. Apparently some older uguru versions
sometimes are distracted for a (relatively) long time. This solves this.
- These timeout errors not only occur in the sending address part of
reading the uguru but also in the wait for read state, so errors in
this state are now handled as retryable just like send address state
errors and are only logged and reported to userspace if 3 executive
tries fail.
- Fix a very nasty bug in the bank1 sensor type detection code, where it
would not restore the original settings in any of the error paths!
- Since not successfully restoring the original settings can seriously
confuse the system BIOS (hang when entering the relevant setup menu),
we now try restoring them 3 times before giving up.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tps65010.c driver in the main tree never got updated with
build fixes since the last batch of I2C driver changes; and the
genirq trigger flags were updated wierdly too.
This also includes a minor tweak to reduce the frequency used to
poll for unplug-the-AC-power on the TPS chips that don't provide
relevant IRQs. It _would_ be nice to sense whether there's even
a battery, but that'd normally be an HDQ/1-wire interface to a
smart battery, and such APIs aren't standardized.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.
This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings. This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements force_pcs module parameter for ata_piix. If 1,
PCS is ignored, 2 honored. As there seem to be quite a few ICHs w/
impaired PCS, this option will be useful for cases where the default
setting doesn't work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There have been a number of reports regarding some ICH5s failing to
detect devices since the PCS handling update. Analysis shows that
these problems are caused by bogus PCS values from those controllers.
Before the PCS update, the driver didn't honor PCS regs exactly and
probed them in many cases PCS reports no device. Now that PCS is
honored exactly, these hardware problems are visible.
This patch makes ICH5 ignore PCS.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some recent myri10ge firmwares support multicast filtering as well
as an extended mcp_irq_data structure (64 instead of 40 bytes).
The new command MXGEFW_CMD_SET_STATS_DMA_V2 is used to check
whether the firmware support those. mgp->fw_multicast_support
is defined accordingly.
When fw_multicast_support is set, some new multicast filtering
commands is passed to the board in myri10ge_set_multicast_list().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add msg_enable and use netif_msg_link to enable/disable reporting
of link status changes since some Ethernet switches seem to generate
a lot of status changes under some circumstances and some people
want to avoid useless flooding in the logs.
Also add a counter for link status changes to statistics.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spectrum_cs: Fix the logic so we error when the device is *not* present!
This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
while playing with gcc 4.1 -Wextra warnings, I came across this one:
drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true
Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.
Tracked down by Fredrik Tolf <fredrik@dolda2000.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in commit 3d0f0fa0cb:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset(). Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE. This fixes ghost device
problem reported on ICH6 and 7.
This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.
* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
failures.
Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
One of my recent changes broke C101 carrier handling, this patch
fixes it. Also fixes an old TX underrun checking bug.
2.6.18 material. Please apply.
Thanks.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes an unused function from the via-velocity-driver.
It doesn't make the binary smaller, but the source cleaner.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the myri10ge driver to use netdev_alloc_skb instead of dev_alloc_skb,
which requires to propagate the net_device across several functions.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem. Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
qeth: bhs must be disabled when accessing neighbour tables.
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@axis.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool -g (show ring sizes) support to the Spidernet network driver.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unclear how these bugs arrived, presumably from incorrect cleanup of
the 16-bit-only paths, but smc91x wouldn't build for OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like broken BIOSes controlling Rhine chips will remain in use in
significant numbers; such systems fail to come up via PXE after they have
been put into D3 (power-saving) mode.
This patch adds a module option for disabling the call that puts the chip
to sleep.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Joerg Bashir <brak@archive.org>
Cc: Tim Phipps <tim@phipps-hutton.freeserve.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When booting using root-nfs, I'm seeing (independently) two lockdep dumps
in the smc91x driver. The patch below fixes both. Both dumps look like
real locking issues.
Nico - please review and ack if you think the patch is correct.
Dump 1:
Sending DHCP requests .
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The poll_enable should be in init_registers before enabling interrupts, not
in tx_timeout. Thanks for spotting it Roger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cc: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x driver forgets to release the spinlock on spurious interrupts.
This little patch fixes it.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add netconsole support to dm9000 driver.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sparc32:
drivers/net/s2io.c:2636: warning: implicit declaration of function 'disable_irq'
drivers/net/s2io.c:2656: warning: implicit declaration of function 'enable_irq'
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/sundance.c:110: error: version causes a section type conflict
I don't understand this error. It's referred to from both __init and
__devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and
is referred to from .init.text.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
distcc[25607] ERROR: compile drivers/net/fealnx.c on g5/64 failed
version[] is referred to from both __init code and from __devinit code, so
move it out of __init altogether.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
drivers/net/tulip/winbond-840.c:141: error: version causes a section type conflict
(For some reason it gets the same error if marked __initdata. Give up.)
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/seeq8005.o - Section mismatch: reference to .init.text:seeq8005_probe from .text between 'init_module' (at offset 0x106) and 'seeq8005_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xfd) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x14b) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.data:wd_portlist from .text between 'init_module' (at offset 0x17f) and 'wd_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2ba0) and 'smctr_reset_adapter'
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text:smctr_probe from .text between 'init_module' (at offset 0x2bf4) and 'smctr_reset_adapter'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x6e6) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x74a) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x7fd) and 'ibmtr_probe_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni52.o - Section mismatch: reference to .init.text:ni52_probe from .text between 'init_module' (at offset 0x997) and 'ni52_close'
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lne390.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'lne390_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lance.o - Section mismatch: reference to .init.data:lance_portlist from .text between 'init_module' (at offset 0x8d3) and 'lance_purge_ring'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x6d2) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6ef) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x702) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x70e) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x71d) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x729) and 'eth16i_multicast'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xdf) and 'es_close'
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'es_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6c3) and 'eexp_hw_lasttxstat'
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x74f) and 'eexp_hw_lasttxstat'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x284) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2a7) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.data:eepro_portlist from .text between 'init_module' (at offset 0x2b3) and 'eepro_ethtool_get_drvinfo'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/e2100.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xd9) and 'e21_reset_8390'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/at1700.o - Section mismatch: reference to .init.text:at1700_probe from .text between 'init_module' (at offset 0x75) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.data:version from .text between 'init_module' (at offset 0x13d8) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1634) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1a1f) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/appletalk/cops.o - Section mismatch: reference to .init.text:cops_probe from .text between 'init_module' (at offset 0xae) and 'cops_rx'
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ac3200.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xf9) and 'ac_close_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/82596.o - Section mismatch: reference to .init.text:i82596_probe from .text between 'init_module' (at offset 0x141) and 'i596_add_cmd'
Also nail a couple of crazy inlines.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stall error handler if attempting resets/aborts while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Background:
Although the transport is using the scsi_timed_out functionality to
restart the timeout if the rport is blocked, if the timeout has already
fired before the block occurs, the eh handler still runs and can take
the device offline. Ultimately, this window cannot be resolved without
significant work in the error handler thread. Christoph noted the first
level of these issues when he noted the poor error response handling
by the error thread.
We found, under heavy load and error testing, that time window from when
the scsi_times_out() adds the io to the queue to when the scsi_error_handler
gets around to servicing it, can be in the several seconds range. In most
cases, these test conditions are highly unusual, but possible.
As a result, we're stalling the error handler in this race window so that
we can avoid the device_offline transitions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Leave all SRQ methods out of the device's uverbs_cmd_mask if the
device doesn't have SRQ support (because of ancient firmware) so that
we don't allow userspace to call the driver's create_srq method. This
fixes a userspace-triggerable oops caused by ib_uverbs_create_srq()
following the device's ->create_srq function pointer, which will be
NULL if the device doesn't support SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PPP code contains two kmalloc()s followed by memset()s without
handling a possible memory allocation failure. (Suggested by Joe
Perches).
And furthermore, conversions from kmalloc+memset to kzalloc.
[akpm@osdl.org: fix error-path leak]
[akpm@osdl.org: cleanups]
[paulus@samba.org: don't add useless printk and cardmap_destroy calls]
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_alloc_skb() to netdev_alloc_skb() and increase default
rx ring size to 255. The old ring size of 100 was too small.
Update version to 1.4.44.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a subtle race condition between bnx2_start_xmit() and bnx2_tx_int()
similar to the one in tg3 discovered by Herbert Xu:
CPU0 CPU1
bnx2_start_xmit()
if (tx_ring_full) {
tx_lock
bnx2_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in bnx2_tx_int() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if bnx2_tx_int() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made, very much identical to the tg3 fix:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in bnx2_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in bnx2_tx_int() before calling
netif_wake_queue().
4. Add memory barrier to bnx2_tx_avail().
5. Add bp->tx_wake_thresh which is set to half the tx ring size.
6. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going through the code, I found out some memory leaks and potential
crashes in drivers/acpi/hotkey.c Please find the patch to fix them.
This patch does the following,
1. Fixes memory leaks in error paths of hotkey_write_config
2. Fixes freeing unallocated pointers in the error paths of hotkey_write_config
3. Uses a loop instead of linear searching for parsing the userspace
input in get_params
4. Uses array of char * instead of passing 4 pointer parameters
explicitly into the init_{poll_}hotkey_* static functions
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reduce writeback threshold by 1. We were instructing the hardware to
wait until the 17th descriptor which went over the cache line limit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
Disable aggressive clocking on esb2 with SERDES port as it causes
hardware problems.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allow NVM to setup LPLU for IGP2 and IGP3. Only IGP needs LPLU D3
disabled during init here.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Explicitly lock two more ethtool entry points completely instead
of the hardware reset only to prevent a race condition.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
