Similar to gre, vxlan, geneve tunnels allow IPIP tunnels to
operate in 'collect metadata' mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of it right away.
ovs can use it as well in the future (once appropriate ovs-vport
abstractions and user apis are added).
Note that just like in other tunnels we cannot cache the dst,
since tunnel_info metadata can be different for every packet.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With large BDP TCP flows and lossy networks, it is very important
to keep a low number of skbs in the write queue.
RACK and SACK processing can perform a linear scan of it.
We should avoid putting any payload in skb->head, so that SACK
shifting can be done if needed.
With this patch, we allow to pack ~0.5 MB per skb instead of
the 64KB initially cooked at tcp_sendmsg() time.
This gives a reduction of number of skbs in write queue by eight.
tcp_rack_detect_loss() likes this.
We still allow payload in skb->head for first skb put in the queue,
to not impact RPC workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a TCP socket gets a large write queue, an overflow can happen
in a test in __tcp_retransmit_skb() preventing all retransmits.
The flow then stalls and resets after timeouts.
Tested:
sysctl -w net.core.wmem_max=1000000000
netperf -H dest -- -s 1000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_rcv_finish() calls l3mdev_ip_rcv(). On any VRF except
the global VRF, this replaces skb->dev with the VRF master interface.
When calling ip_route_input_noref() from here, the checks for forwarding
look at this master device instead of the initial ingress interface.
This will allow packets to be routed which normally would be dropped.
For example, an interface that is not assigned an IP address should
drop packets, but because the checking is against the master device, the
packet will be forwarded.
The fix here is to still call l3mdev_ip_rcv(), but remember the initial
net_device. This is passed to the other functions within ip_rcv_finish,
so they still see the original interface.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb replaces another one in ooo queue, I forgot to also
update tp->ooo_last_skb as well, if the replaced skb was the last one
in the queue.
To fix this, we simply can re-use the code that runs after an insertion,
trying to merge skbs at the right of current skb.
This not only fixes the bug, but also remove all small skbs that might
be a subset of the new one.
Example:
We receive segments 2001:3001, 4001:5001
Then we receive 2001:8001 : We should replace 2001:3001 with the big
skb, but also remove 4001:50001 from the queue to save space.
packetdrill test demonstrating the bug
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
+0.100 < . 1:1(0) ack 1 win 1024
+0 accept(3, ..., ...) = 4
+0.01 < . 1001:2001(1000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001>
+0.01 < . 1001:3001(2000) ack 1 win 1024
+0 > . 1:1(0) ack 1 <nop,nop, sack 1001:2001 1001:3001>
Fixes: 9f5afeae51 ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Endianess fix for the new nf_tables netlink trace infrastructure,
NFTA_TRACE_POLICY endianess was not correct, patch from Liping Zhang.
2) Fix broken re-route after userspace queueing in nf_tables route
chain. This patch is large but it is simple since it is just getting
this code in sync with iptable_mangle. Also from Liping.
3) NAT mangling via ctnetlink lies to userspace when nf_nat_setup_info()
fails to setup the NAT conntrack extension. This problem has been
there since the beginning, but it can now show up after rhashtable
conversion.
4) Fix possible NULL pointer dereference due to failures in allocating
the synproxy and seqadj conntrack extensions, from Gao feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some codes of netfilter module which did not check the return
value of nft_register_chain_type. Add the checks now.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch introduces nft_set_pktinfo_unspec() that ensures proper
initialization all of pktinfo fields for non-IP traffic. This is used
by the bridge, netdev and arp families.
This new function relies on nft_set_pktinfo_proto_unspec() to set a new
tprot_set field that indicates if transport protocol information is
available. Remain fields are zeroed.
The meta expression has been also updated to check to tprot_set in first
place given that zero is a valid tprot value. Even a handcrafted packet
may come with the IPPROTO_RAW (255) protocol number so we can't rely on
this value as tprot unset.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A previous patch added l3mdev flow update making these hooks
redundant. Remove them.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IPv4 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv4 output processing to
send the packet to the VRF driver on xmit.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an L3 master device to act as the loopback for that L3 domain.
For IPv4 the device can also have the address 127.0.0.1.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure to the output path to pass an skb
to an l3mdev device if it has a hook registered. This is the Tx parallel
to l3mdev_ip{6}_rcv in the receive path and is the basis for removing
the existing hook that returns the vrf dst on the fib lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add l3mdev hook to set FLOWI_FLAG_SKIP_NH_OIF flag and update oif/iif
in flow struct if its oif or iif points to a device enslaved to an L3
Master device. Only 1 needs to be converted to match the l3mdev FIB
rule. This moves the flow adjustment for l3mdev to a single point
catching all lookups. It is redundant for existing hooks (those are
removed in later patches) but is needed for missed lookups such as
PMTU updates.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem noticed that we could avoid an rbtree lookup if the
the attempt to coalesce incoming skb to the last skb failed
for some reason.
Since most ooo additions are at the tail, this is definitely
worth adding a test and fast path.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add utility functions to convert a 32 bits key into a 64 bits tunnel and
vice versa.
These functions will be used instead of cloning code in GRE and VXLAN,
and in tc act_iptunnel which will be introduced in a following patch in
this patchset.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb has a valid l4 hash, there is no point clearing hash and force
a further flow dissection when a tunnel encapsulation is added.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_table_insert() inconsistently fills the nlmsg_flags field in its
notification messages.
Since commit b8f5583135 ("[RTNETLINK]: Fix sending netlink message
when replace route."), the netlink message has its nlmsg_flags set to
NLM_F_REPLACE if the route replaced a preexisting one.
Then commit a2bb6d7d6f ("ipv4: include NLM_F_APPEND flag in append
route notifications") started setting nlmsg_flags to NLM_F_APPEND if
the route matched a preexisting one but was appended.
In other cases (exclusive creation or prepend), nlmsg_flags is 0.
This patch sets ->nlmsg_flags in all situations, preserving the
semantic of the NLM_F_* bits:
* NLM_F_CREATE: a new fib entry has been created for this route.
* NLM_F_EXCL: no other fib entry existed for this route.
* NLM_F_REPLACE: this route has overwritten a preexisting fib entry.
* NLM_F_APPEND: the new fib entry was added after other entries for
the same route.
As a result, the possible flag combination can now be reported
(iproute2's terminology into parentheses):
* NLM_F_CREATE | NLM_F_EXCL: route didn't exist, exclusive creation
("add").
* NLM_F_CREATE | NLM_F_APPEND: route did already exist, new route
added after preexisting ones ("append").
* NLM_F_CREATE: route did already exist, new route added before
preexisting ones ("prepend").
* NLM_F_REPLACE: route did already exist, new route replaced the
first preexisting one ("change").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of inter address family tunneling (IPv6 over vti4 or IPv4 over
vti6), the inbound policy checks in vti_rcv_cb() and vti6_rcv_cb() are
using the wrong address family. As a result, all inbound inter address
family traffic is dropped.
Use the xfrm_ip2inner_mode() helper, as done in xfrm_input() (i.e., also
increment LINUX_MIB_XFRMINSTATEMODEERROR in case of error), to select the
inner_mode that contains the right address family for the inbound policy
checks.
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit f02db315b8 ("ipv4: IP_TOS and IP_TTL can be specified as
ancillary data") Francesco added IP_TOS values specified as integer.
However, kernel sends to userspace (at recvmsg() time) an IP_TOS value
in a single byte, when IP_RECVTOS is set on the socket.
It can be very useful to reflect all ancillary options as given by the
kernel in a subsequent sendmsg(), instead of aborting the sendmsg() with
EINVAL after Francesco patch.
So this patch extends IP_TOS ancillary to accept an u8, so that an UDP
server can simply reuse same ancillary block without having to mangle
it.
Jesper can then augment
https://github.com/netoptimizer/network-testing/blob/master/src/udp_example02.c
to add TOS reflection ;)
Fixes: f02db315b8 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Francesco Fusco <ffusco@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, TCP BDP has increased by several orders of magnitude,
and some people are considering to reach the 2 Gbytes limit.
Even with current window scale limit of 14, ~1 Gbytes maps to ~740,000
MSS.
In presence of packet losses (or reorders), TCP stores incoming packets
into an out of order queue, and number of skbs sitting there waiting for
the missing packets to be received can be in the 10^5 range.
Most packets are appended to the tail of this queue, and when
packets can finally be transferred to receive queue, we scan the queue
from its head.
However, in presence of heavy losses, we might have to find an arbitrary
point in this queue, involving a linear scan for every incoming packet,
throwing away cpu caches.
This patch converts it to a RB tree, to get bounded latencies.
Yaogong wrote a preliminary patch about 2 years ago.
Eric did the rebase, added ofo_last_skb cache, polishing and tests.
Tested with network dropping between 1 and 10 % packets, with good
success (about 30 % increase of throughput in stress tests)
Next step would be to also use an RB tree for the write queue at sender
side ;)
Signed-off-by: Yaogong Wang <wygivan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-By: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 76174004a0
(tcp: do not slow start when cwnd equals ssthresh )
introduced regression in TCP YeAH. Using 100ms delay 1% loss virtual
ethernet link kernel 4.2 shows bandwidth ~500KB/s for single TCP
connection and kernel 4.3 and above (including 4.8-rc4) shows bandwidth
~100KB/s.
That is caused by stalled cwnd when cwnd equals ssthresh. This patch
fixes it by proper increasing cwnd in this case.
Signed-off-by: Artem Germanov <agermanov@anchorfree.com>
Acked-by: Dmitry Adamushko <d.adamushko@anchorfree.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the capability for a process that has CAP_NET_ADMIN on
a socket to see the socket mark in socket dumps.
Commit a52e95abf7 ("net: diag: allow socket bytecode filters to
match socket marks") recently gave privileged processes the
ability to filter socket dumps based on mark. This patch is
complementary: it ensures that the mark is also passed to
userspace in the socket's netlink attributes. It is useful for
tools like ss which display information about sockets.
Tested: https://android-review.googlesource.com/270210
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DATA and/or FIN are carried in a SYN/ACK message or SYN message,
we append an skb in socket receive queue, but we forget to call
sk_forced_mem_schedule().
Effect is that the socket has a negative sk->sk_forward_alloc as long as
the message is not read by the application.
Josh Hunt fixed a similar issue in commit d22e153718 ("tcp: fix tcp
fin memory accounting")
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipsec 2016-09-08
1) Fix a crash when xfrm_dump_sa returns an error.
From Vegard Nossum.
2) Remove some incorrect WARN() on normal error handling.
From Vegard Nossum.
3) Ignore socket policies when rebuilding hash tables,
socket policies are not inserted into the hash tables.
From Tobias Brunner.
4) Initialize and check tunnel pointers properly before
we use it. From Alexey Kodanev.
5) Fix l3mdev oif setting on xfrm dst lookups.
From David Ahern.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_diag_destroy does look up the IPv4 UDP hashtable for mapped
addresses, but it gets the IPv4 address to look up from the
beginning of the IPv6 address instead of the end.
Tested: https://android-review.googlesource.com/269874
Fixes: 5d77dca828 ("net: diag: support SOCK_DESTROY for UDP sockets")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two existing strutures which defines the GRE and PPTP header.
So use these two structures instead of the ones defined by netfilter to
keep consitent with other codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are already some GRE_* macros in kernel, so it is unnecessary
to define these macros. And remove some useless macros
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When deleting an IP address from an interface, there is a clean-up of
routes which refer to this local address. However, there was no check to
see that the VRF matched. This meant that deletion wasn't confined to
the VRF it should have been.
To solve this, a new field has been added to fib_info to hold a table
id. When removing fib entries corresponding to a local ip address, this
table id is also used in the comparison.
The table id is populated when the fib_info is created. This was already
done in some places, but not in ip_rt_ioctl(). This has now been fixed.
Fixes: 021dd3b8a1 ("net: Add routes to the table associated with the device")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Most relevant updates are the removal of per-conntrack timers to
use a workqueue/garbage collection approach instead from Florian
Westphal, the hash and numgen expression for nf_tables from Laura
Garcia, updates on nf_tables hash set to honor the NLM_F_EXCL flag,
removal of ip_conntrack sysctl and many other incremental updates on our
Netfilter codebase.
More specifically, they are:
1) Retrieve only 4 bytes to fetch ports in case of non-linear skb
transport area in dccp, sctp, tcp, udp and udplite protocol
conntrackers, from Gao Feng.
2) Missing whitespace on error message in physdev match, from Hangbin Liu.
3) Skip redundant IPv4 checksum calculation in nf_dup_ipv4, from Liping Zhang.
4) Add nf_ct_expires() helper function and use it, from Florian Westphal.
5) Replace opencoded nf_ct_kill() call in IPVS conntrack support, also
from Florian.
6) Rename nf_tables set implementation to nft_set_{name}.c
7) Introduce the hash expression to allow arbitrary hashing of selector
concatenations, from Laura Garcia Liebana.
8) Remove ip_conntrack sysctl backward compatibility code, this code has
been around for long time already, and we have two interfaces to do
this already: nf_conntrack sysctl and ctnetlink.
9) Use nf_conntrack_get_ht() helper function whenever possible, instead
of opencoding fetch of hashtable pointer and size, patch from Liping Zhang.
10) Add quota expression for nf_tables.
11) Add number generator expression for nf_tables, this supports
incremental and random generators that can be combined with maps,
very useful for load balancing purpose, again from Laura Garcia Liebana.
12) Fix a typo in a debug message in FTP conntrack helper, from Colin Ian King.
13) Introduce a nft_chain_parse_hook() helper function to parse chain hook
configuration, this is used by a follow up patch to perform better chain
update validation.
14) Add rhashtable_lookup_get_insert_key() to rhashtable and use it from the
nft_set_hash implementation to honor the NLM_F_EXCL flag.
15) Missing nulls check in nf_conntrack from nf_conntrack_tuple_taken(),
patch from Florian Westphal.
16) Don't use the DYING bit to know if the conntrack event has been already
delivered, instead a state variable to track event re-delivery
states, also from Florian.
17) Remove the per-conntrack timer, use the workqueue approach that was
discussed during the NFWS, from Florian Westphal.
18) Use the netlink conntrack table dump path to kill stale entries,
again from Florian.
19) Add a garbage collector to get rid of stale conntracks, from
Florian.
20) Reschedule garbage collector if eviction rate is high.
21) Get rid of the __nf_ct_kill_acct() helper.
22) Use ARPHRD_ETHER instead of hardcoded 1 from ARP logger.
23) Make nf_log_set() interface assertive on unsupported families.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Imagine such situation, user add the following nft rules, and queue
the packets to userspace for further check:
# ip rule add fwmark 0x0/0x1 lookup eth0
# ip rule add fwmark 0x1/0x1 lookup eth1
# nft add table filter
# nft add chain filter output {type route hook output priority 0 \;}
# nft add rule filter output mark set 0x1
# nft add rule filter output queue num 0
But after we reinject the skbuff, the packet will be sent via the
wrong route, i.e. in this case, the packet will be routed via eth0
table, not eth1 table. Because we skip to do re-route when verdict
is NF_QUEUE, even if the mark was changed.
Acctually, we should not touch sk_buff if verdict is NF_DROP or
NF_STOLEN, and when re-route fails, return NF_DROP with error code.
This is consistent with the mangle table in iptables.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Yuchung noticed that on the first TFO server data packet sent after
the (TFO) handshake, the server echoed the TCP timestamp value in the
SYN/data instead of the timestamp value in the final ACK of the
handshake. This problem did not happen on regular opens.
The tcp_replace_ts_recent() logic that decides whether to remember an
incoming TS value needs tp->rcv_wup to hold the latest receive
sequence number that we have ACKed (latest tp->rcv_nxt we have
ACKed). This commit fixes this issue by ensuring that a TFO server
properly updates tp->rcv_wup to match tp->rcv_nxt at the time it sends
a SYN/ACK for the SYN/data.
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: David S. Miller <davem@davemloft.net>
All changes are notified, but the initial state was missing.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_log_set is an interface function, so it should do the strict sanity
check of parameters. Convert the return value of nf_log_set as int instead
of void. When the pf is invalid, return -EOPNOTSUPP.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is one macro ARPHRD_ETHER which defines the ethernet proto for ARP,
so we could use it instead of the literal number '1'.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When TCP operates in lossy environments (between 1 and 10 % packet
losses), many SACK blocks can be exchanged, and I noticed we could
drop them on busy senders, if these SACK blocks have to be queued
into the socket backlog.
While the main cause is the poor performance of RACK/SACK processing,
we can try to avoid these drops of valuable information that can lead to
spurious timeouts and retransmits.
Cause of the drops is the skb->truesize overestimation caused by :
- drivers allocating ~2048 (or more) bytes as a fragment to hold an
Ethernet frame.
- various pskb_may_pull() calls bringing the headers into skb->head
might have pulled all the frame content, but skb->truesize could
not be lowered, as the stack has no idea of each fragment truesize.
The backlog drops are also more visible on bidirectional flows, since
their sk_rmem_alloc can be quite big.
Let's add some room for the backlog, as only the socket owner
can selectively take action to lower memory needs, like collapsing
receive queues or partial ofo pruning.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In inet_stream_ops we set read_sock to tcp_read_sock and peek_len to
tcp_peek_len (which is just a stub function that calls tcp_inq).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds SNMP counter for drops caused by MD5 mismatches.
The current syslog might help, but a counter is more precise and helps
monitoring.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP MD5 mismatches do increment sk_drops counter in all states but
SYN_RECV.
This is very unlikely to happen in the real world, but worth adding
to help diagnostics.
We increase the parent (listener) sk_drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After I add the nft rule "nft add rule filter prerouting reject
with tcp reset", kernel panic happened on my system:
NULL pointer dereference at ...
IP: [<ffffffff81b9db2f>] nf_send_reset+0xaf/0x400
Call Trace:
[<ffffffff81b9da80>] ? nf_reject_ip_tcphdr_get+0x160/0x160
[<ffffffffa0928061>] nft_reject_ipv4_eval+0x61/0xb0 [nft_reject_ipv4]
[<ffffffffa08e836a>] nft_do_chain+0x1fa/0x890 [nf_tables]
[<ffffffffa08e8170>] ? __nft_trace_packet+0x170/0x170 [nf_tables]
[<ffffffffa06e0900>] ? nf_ct_invert_tuple+0xb0/0xc0 [nf_conntrack]
[<ffffffffa07224d4>] ? nf_nat_setup_info+0x5d4/0x650 [nf_nat]
[...]
Because in the PREROUTING chain, routing information is not exist,
then we will dereference the NULL pointer and oops happen.
So we restrict reject expression to INPUT, FORWARD and OUTPUT chain.
This is consistent with iptables REJECT target.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows a privileged process to filter by socket mark when
dumping sockets via INET_DIAG_BY_FAMILY. This is useful on
systems that use mark-based routing such as Android.
The ability to filter socket marks requires CAP_NET_ADMIN, which
is consistent with other privileged operations allowed by the
SOCK_DIAG interface such as the ability to destroy sockets and
the ability to inspect BPF filters attached to packet sockets.
Tested: https://android-review.googlesource.com/261350
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code a bit and also allows inet_diag_bc_audit
to send to userspace an error that isn't EINVAL.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use SLAB_DESTROY_BY_RCU for UDP,
we do not need sk_prot_clear_portaddr_nulls() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements SOCK_DESTROY for UDP sockets similar to what was done
for TCP with commit c1e64e298b ("net: diag: Support destroying TCP
sockets.") A process with a UDP socket targeted for destroy is awakened
and recvmsg fails with ECONNABORTED.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_diag_find_one_icsk takes a reference to a socket that is not
released if sock_diag_destroy returns an error. Fix by changing
tcp_diag_destroy to manage the refcnt for all cases and remove
the sock_put calls from tcp_abort.
Fixes: c1e64e298b ("net: diag: Support destroying TCP sockets")
Reported-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ca065d0cf8 ("udp: no longer use SLAB_DESTROY_BY_RCU")
we do not need this special allocation mode anymore, even if it is
harmless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TFO_SERVER_WO_SOCKOPT2 was intended for debugging purposes during
Fast Open development. Remove this config option and also
update/clean-up the documentation of the Fast Open sysctl.
Reported-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laura tracked poll() [and friends] regression caused by commit
e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
udp_poll() needs to know if there is a valid packet in receive queue,
even if its payload length is 0.
Change first_packet_length() to return an signed int, and use -1
as the indication of an empty queue.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no RARP, BOOTP, or DHCP response is received, ic_dev is never set,
causing a NULL pointer dereference in ic_close_devs():
Sending DHCP requests ...... timed out!
Unable to handle kernel NULL pointer dereference at virtual address 00000004
To fix this, add a check to avoid dereferencing ic_dev if it is still
NULL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
Signed-off-by: David S. Miller <davem@davemloft.net>
In b8247f095e,
"net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs"
gso skbs arriving from an ingress interface that go through UDP
tunneling, are allowed to be fragmented if the resulting encapulated
segments exceed the dst mtu of the egress interface.
This aligned the behavior of gso skbs to non-gso skbs going through udp
encapsulation path.
However the non-gso vs gso anomaly is present also in the following
cases of a GRE tunnel:
- ip_gre in collect_md mode, where TUNNEL_DONT_FRAGMENT is not set
(e.g. OvS vport-gre with df_default=false)
- ip_gre in nopmtudisc mode, where IFLA_GRE_IGNORE_DF is set
In both of the above cases, the non-gso skbs get fragmented, whereas the
gso skbs (having skb_gso_network_seglen that exceeds dst mtu) get dropped,
as they don't go through the segment+fragment code path.
Fix: Setting IPSKB_FRAG_SEGS if the tunnel specified IP_DF bit is NOT set.
Tunnels that do set IP_DF, will not go to fragmentation of segments.
This preserves behavior of ip_gre in (the default) pmtudisc mode.
Fixes: b8247f095e ("net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs")
Reported-by: wenxu <wenxu@ucloud.cn>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Tested-by: wenxu <wenxu@ucloud.cn>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subash reported that commit 42a7b32b73 ("xfrm: Add oif to dst lookups")
broke a wifi use case that uses fib rules and xfrms. The intent of
42a7b32b73 was driven by VRFs with IPsec. As a compromise relax the
use of oif in xfrm lookups to L3 master devices only (ie., oif is either
an L3 master device or is enslaved to a master device).
Fixes: 42a7b32b73 ("xfrm: Add oif to dst lookups")
Reported-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Fixes following sparse errors :
net/ipv4/fib_semantics.c:1579:61: warning: incorrect type in argument 2
(different base types)
net/ipv4/fib_semantics.c:1579:61: expected unsigned int [unsigned]
[usertype] key
net/ipv4/fib_semantics.c:1579:61: got restricted __be32 const
[usertype] nh_gw
Fixes: a6db4494d2 ("net: ipv4: Consider failed nexthops in multipath routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include ipv4_rcv_saddr_equal() definition to avoid this sparse error :
net/ipv4/udp.c:362:5: warning: symbol 'ipv4_rcv_saddr_equal' was not
declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 19689e38ec ("tcp: md5: use kmalloc() backed scratch
areas") this function is no longer used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix one typo: s/tn/tp/
2) Fix the description about the "u" bits.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, TCP BDP has increased a lot, and is typically
in the order of ~10 Mbytes with help of clever Congestion Control
modules.
In presence of packet losses, TCP stores incoming packets into an out of
order queue, and number of skbs sitting there waiting for the missing
packets to be received can match the BDP (~10 Mbytes)
In some cases, TCP needs to make room for incoming skbs, and current
strategy can simply remove all skbs in the out of order queue as a last
resort, incurring a huge penalty, both for receiver and sender.
Unfortunately these 'last resort events' are quite frequent, forcing
sender to send all packets again, stalling the flow and wasting a lot of
resources.
This patch cleans only a part of the out of order queue in order
to meet the memory constraints.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: C. Stephen Gun <csg@google.com>
Cc: Van Jacobson <vanj@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing tcp_xmit_retransmit_queue() kasan issue, I found
that we could avoid reading sacked field of skb that we wont send,
possibly removing one cache line miss.
Very minor change in slow path, but why not ? ;)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 9c706a49d6 ("net: ipconfig: fix use after free") avoids
the use after free, the resulting code still ends up calling both the
ic_setup_if() and ic_setup_routes() after calling ic_close_devs(), and
access to the device is still required.
Move the call to ic_close_devs() to the very end of the function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the inner_protocol is set on transmit so that GSO segmentation,
which relies on that field, works correctly.
This is achieved by setting the inner_protocol in gre_build_header rather
than each caller of that function. It ensures that the inner_protocol is
set when gre_fb_xmit() is used to transmit GRE which was not previously the
case.
I have observed this is not the case when OvS transmits GRE using
lwtunnel metadata (which it always does).
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Cc: Pravin Shelar <pshelar@ovn.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This backward compatibility has been around for more than ten years,
since Yasuyuki Kozakai introduced IPv6 in conntrack. These days, we have
alternate /proc/net/nf_conntrack* entries, the ctnetlink interface and
the conntrack utility got adopted by many people in the user community
according to what I observed on the netfilter user mailing list.
So let's get rid of this.
Note that nf_conntrack_htable_size and unsigned int nf_conntrack_max do
not need to be exported as symbol anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
... so we don't need to touch all of these places when we get rid of the
timer in nf_conn.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IP header checksum will be recalculated at ip_local_out, so
there's no need to calculated it here, remove it. Also update
code comments to illustrate it, and delete the misleading
comments about checksum recalculation.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ic_close_devs() calls kfree() for all devices's ic_device. Since commit
2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
the active device's ic_device is still used however to print the
ipconfig summary which results in an oops if the memory is already
changed. So delay freeing until after the autoconfig results are
reported.
Fixes: 2647cffb2b ("net: ipconfig: Support using "delayed" DHCP replies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
fib_local is set but not used. Remove it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When executing the script included below, the netns delete operation
hangs with the following message (repeated at 10 second intervals):
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 1
This occurs because a reference to the lo interface in the "secure" netns
is still held by a dst entry in the xfrm bundle cache in the init netns.
Address this problem by garbage collecting the tunnel netns flow cache
when a cross-namespace vti interface receives a NETDEV_DOWN notification.
A more detailed description of the problem scenario (referencing commands
in the script below):
(1) ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
The vti_test interface is created in the init namespace. vti_tunnel_init()
attaches a struct ip_tunnel to the vti interface's netdev_priv(dev),
setting the tunnel net to &init_net.
(2) ip link set vti_test netns secure
The vti_test interface is moved to the "secure" netns. Note that
the associated struct ip_tunnel still has tunnel->net set to &init_net.
(3) ip netns exec secure ping -c 4 -i 0.02 -I 192.168.100.1 192.168.200.1
The first packet sent using the vti device causes xfrm_lookup() to be
called as follows:
dst = xfrm_lookup(tunnel->net, skb_dst(skb), fl, NULL, 0);
Note that tunnel->net is the init namespace, while skb_dst(skb) references
the vti_test interface in the "secure" namespace. The returned dst
references an interface in the init namespace.
Also note that the first parameter to xfrm_lookup() determines which flow
cache is used to store the computed xfrm bundle, so after xfrm_lookup()
returns there will be a cached bundle in the init namespace flow cache
with a dst referencing a device in the "secure" namespace.
(4) ip netns del secure
Kernel begins to delete the "secure" namespace. At some point the
vti_test interface is deleted, at which point dst_ifdown() changes
the dst->dev in the cached xfrm bundle flow from vti_test to lo (still
in the "secure" namespace however).
Since nothing has happened to cause the init namespace's flow cache
to be garbage collected, this dst remains attached to the flow cache,
so the kernel loops waiting for the last reference to lo to go away.
<Begin script>
ip link add br1 type bridge
ip link set dev br1 up
ip addr add dev br1 1.1.1.1/8
ip netns add secure
ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
ip link set vti_test netns secure
ip netns exec secure ip link set vti_test up
ip netns exec secure ip link s lo up
ip netns exec secure ip addr add dev lo 192.168.100.1/24
ip netns exec secure ip route add 192.168.200.0/24 dev vti_test
ip xfrm policy flush
ip xfrm state flush
ip xfrm policy add dir out tmpl src 1.1.1.1 dst 1.1.1.2 \
proto esp mode tunnel mark 1
ip xfrm policy add dir in tmpl src 1.1.1.2 dst 1.1.1.1 \
proto esp mode tunnel mark 1
ip xfrm state add src 1.1.1.1 dst 1.1.1.2 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip xfrm state add src 1.1.1.2 dst 1.1.1.1 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip netns exec secure ping -c 4 -i 0.02 -I 192.168.100.1 192.168.200.1
ip netns del secure
<End script>
Reported-by: Hangbin Liu <haliu@redhat.com>
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on RFC3376 5.1 and RFC3810 6.1
If the per-interface listening change that triggers the new report is
a filter mode change, then the next [Robustness Variable] State
Change Reports will include a Filter Mode Change Record. This
applies even if any number of source list changes occur in that
period.
Old State New State State Change Record Sent
--------- --------- ------------------------
INCLUDE (A) EXCLUDE (B) TO_EX (B)
EXCLUDE (A) INCLUDE (B) TO_IN (B)
So we should not send source-list change if there is a filter-mode change.
Here are two scenarios:
1. Group deleted and filter mode is EXCLUDE, which means we need send a
TO_IN { }.
2. Not group deleted, but has pcm->crcount, which means we need send a
normal filter-mode-change.
At the same time, if the type is ALLOW or BLOCK, and have psf->sf_crcount,
we stop add records and decrease sf_crcount directly
Reference: https://www.ietf.org/mail-archive/web/magma/current/msg01274.html
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipconfig learned to handle "delayed replies" in the previous
commit, there is no reason any more to delay sending a first request per
device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dhcp code only waits 1s between sending DHCP requests on different
devices and only accepts an answer for the device that sent out the last
request. Only the timeout at the end of a loop is increased iteratively
which favours only the last device. This makes it impossible to work
with a dhcp server that takes little more than 1s connected to a device
that is not the last one.
Instead of also increasing the inter-device timeout, teach the code to
handle delayed replies.
To accomplish that, make *ic_dev track the current ic_device instead of
the current net_device and adapt all users accordingly. The relevant
change then is to reset d to ic_dev on a reply to assert that the
followup request goes through the right device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies understanding what happens when there is more than one
device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1f ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
Currently lastuse is updated on entry creation and cache hit, but it should
also be updated on entry change. Since both on add and update the ttl array
is updated we can simply update the lastuse in ipmr_update_thresholds.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a612769774 ("udp: prevent bugcheck if filter truncates packet
too much"), there followed various other fixes for similar cases such
as f4979fcea7 ("rose: limit sk_filter trim to payload").
Latter introduced a new helper sk_filter_trim_cap(), where we can pass
the trim limit directly to the socket filter handling. Make use of it
here as well with sizeof(struct udphdr) as lower cap limit and drop the
extra skb->len test in UDP's input path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
they are:
1) Count pre-established connections as active in "least connection"
schedulers such that pre-established connections to avoid overloading
backend servers on peak demands, from Michal Kubecek via Simon Horman.
2) Address a race condition when resizing the conntrack table by caching
the bucket size when fulling iterating over the hashtable in these
three possible scenarios: 1) dump via /proc/net/nf_conntrack,
2) unlinking userspace helper and 3) unlinking custom conntrack timeout.
From Liping Zhang.
3) Revisit early_drop() path to perform lockless traversal on conntrack
eviction under stress, use del_timer() as synchronization point to
avoid two CPUs evicting the same entry, from Florian Westphal.
4) Move NAT hlist_head to nf_conn object, this simplifies the existing
NAT extension and it doesn't increase size since recent patches to
align nf_conn, from Florian.
5) Use rhashtable for the by-source NAT hashtable, also from Florian.
6) Don't allow --physdev-is-out from OUTPUT chain, just like
--physdev-out is not either, from Hangbin Liu.
7) Automagically set on nf_conntrack counters if the user tries to
match ct bytes/packets from nftables, from Liping Zhang.
8) Remove possible_net_t fields in nf_tables set objects since we just
simply pass the net pointer to the backend set type implementations.
9) Fix possible off-by-one in h323, from Toby DiPasquale.
10) early_drop() may be called from ctnetlink patch, so we must hold
rcu read size lock from them too, this amends Florian's patch #3
coming in this batch, from Liping Zhang.
11) Use binary search to validate jump offset in x_tables, this
addresses the O(n!) validation that was introduced recently
resolve security issues with unpriviledge namespaces, from Florian.
12) Fix reference leak to connlabel in error path of nft_ct, from Zhang.
13) Three updates for nft_log: Fix log prefix leak in error path. Bail
out on loglevel larger than debug in nft_log and set on the new
NF_LOG_F_COPY_LEN flag when snaplen is specified. Again from Zhang.
14) Allow to filter rule dumps in nf_tables based on table and chain
names.
15) Simplify connlabel to always use 128 bits to store labels and
get rid of unused function in xt_connlabel, from Florian.
16) Replace set_expect_timeout() by mod_timer() from the h323 conntrack
helper, by Gao Feng.
17) Put back x_tables module reference in nft_compat on error, from
Liping Zhang.
18) Add a reference count to the x_tables extensions cache in
nft_compat, so we can remove them when unused and avoid a crash
if the extensions are rmmod, again from Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Given:
- tap0 and vxlan0 are bridged
- vxlan0 stacked on eth0, eth0 having small mtu (e.g. 1400)
Assume GSO skbs arriving from tap0 having a gso_size as determined by
user-provided virtio_net_hdr (e.g. 1460 corresponding to VM mtu of 1500).
After encapsulation these skbs have skb_gso_network_seglen that exceed
eth0's ip_skb_dst_mtu.
These skbs are accidentally passed to ip_finish_output2 AS IS.
Alas, each final segment (segmented either by validate_xmit_skb or by
hardware UFO) would be larger than eth0 mtu.
As a result, those above-mtu segments get dropped on certain networks.
This behavior is not aligned with the NON-GSO case:
Assume a non-gso 1500-sized IP packet arrives from tap0. After
encapsulation, the vxlan datagram is fragmented normally at the
ip_finish_output-->ip_fragment code path.
The expected behavior for the GSO case would be segmenting the
"gso-oversized" skb first, then fragmenting each segment according to
dst mtu, and finally passing the resulting fragments to ip_finish_output2.
'ip_finish_output_gso' already supports this "Slowpath" behavior,
according to the IPSKB_FRAG_SEGS flag, which is only set during ipv4
forwarding (not set in the bridged case).
In order to support the bridged case, we'll mark skbs arriving from an
ingress interface that get udp-encaspulated as "allowed to be fragmented",
causing their network_seglen to be validated by 'ip_finish_output_gso'
(and fragment if needed).
Note the TUNNEL_DONT_FRAGMENT tun_flag is still honoured (both in the
gso and non-gso cases), which serves users wishing to forbid
fragmentation at the udp tunnel endpoint.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag indicates whether fragmentation of segments is allowed.
Formerly this policy was hardcoded according to IPSKB_FORWARDED (set by
either ip_forward or ipmr_forward).
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 3647234101 (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 3647234101 ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In preparation for hardware offloading of ipmr/ip6mr we need an
interface that allows to check (and later update) the age of entries.
Relying on stats alone can show activity but not actual age of the entry,
furthermore when there're tens of thousands of entries a lot of the
hardware implementations only support "hit" bits which are cleared on
read to denote that the entry was active and shouldn't be aged out,
these can then be naturally translated into age timestamp and will be
compatible with the software forwarding age. Using a lastuse entry doesn't
affect performance because the members in that cache line are written to
along with the age.
Since all new users are encouraged to use ipmr via netlink, this is
exported via the RTA_EXPIRES attribute.
Also do a minor local variable declaration style adjustment - arrange them
longest to shortest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Shrijeet Mukherjee <shm@cumulusnetworks.com>
CC: Satish Ashok <sashok@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds kernel-doc style descriptions for 6 functions and
fixes 1 typo.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-socket rate limit for 'challenge acks' was introduced in the
context of limiting ack loops:
commit f2b2c582e8 ("tcp: mitigate ACK loops for connections as tcp_sock")
And I think it can be extended to rate limit all 'challenge acks' on a
per-socket basis.
Since we have the global tcp_challenge_ack_limit, this patch allows for
tcp_challenge_ack_limit to be set to a large value and effectively rely on
the per-socket limit, or set tcp_challenge_ack_limit to a lower value and
still prevents a single connections from consuming the entire challenge ack
quota.
It further moves in the direction of eliminating the global limit at some
point, as Eric Dumazet has suggested. This a follow-up to:
Subject: tcp: make challenge acks less predictable
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Makefile controlling compilation of this file is obj-y,
meaning that it currently is never being built as a module.
Since MODULE_ALIAS is a no-op for non-modular code, we can simply
remove the MODULE_ALIAS_NETPROTO variant used here.
We replace module.h with kmod.h since the file does make use of
request_module() in order to load other modules from here.
We don't have to worry about init.h coming in via the removed
module.h since the file explicitly includes init.h already.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum is reporting for a crash in fib_dump_info
when nh_dev = NULL and fib_nhs == 1:
Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+
RIP: 0033:[<00000000602b3d18>]
RSP: 0000000062623890 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00
RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000
R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00
R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000
Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18
CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581
Stack:
626238f0 960226a02 00000400 000000fe
62623910 600afca7 62623970 62623a48
62468038 00000018 00000000 00000000
Call Trace:
[<602b3e93>] rtmsg_fib+0xd3/0x190
[<602b6680>] fib_table_insert+0x260/0x500
[<602b0e5d>] inet_rtm_newroute+0x4d/0x60
[<60250def>] rtnetlink_rcv_msg+0x8f/0x270
[<60267079>] netlink_rcv_skb+0xc9/0xe0
[<60250d4b>] rtnetlink_rcv+0x3b/0x50
[<60265400>] netlink_unicast+0x1a0/0x2c0
[<60265e47>] netlink_sendmsg+0x3f7/0x470
[<6021dc9a>] sock_sendmsg+0x3a/0x90
[<6021e0d0>] ___sys_sendmsg+0x300/0x360
[<6021fa64>] __sys_sendmsg+0x54/0xa0
[<6021fac0>] SyS_sendmsg+0x10/0x20
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
$ addr2line -e vmlinux -i 0x602b3d18
include/linux/inetdevice.h:222
net/ipv4/fib_semantics.c:1264
Problem happens when RTNH_F_LINKDOWN is provided from user space
when creating routes that do not use the flag, catched with
netlink fuzzer.
Currently, the kernel allows user space to set both flags
to nh_flags and fib_flags but this is not intentional, the
assumption was that they are not set. Fix this by rejecting
both flags with EINVAL.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Fixes: 0eeb075fad ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Dinesh Dutt <ddutt@cumulusnetworks.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Reported-by: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a combination if #if conditionals and goto labels to unwind
tunnel4_init seems unwieldy. This patch takes a simpler approach of
directly unregistering previously registered protocols when an error
occurs.
This fixes a number of problems with the current implementation
including the potential presence of labels when they are unused
and the potential absence of unregister code when it is needed.
Fixes: 8afe97e5d4 ("tunnels: support MPLS over IPv4 tunnels")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we do "cat /proc/net/nf_conntrack", and meanwhile resize the conntrack
hash table via /sys/module/nf_conntrack/parameters/hashsize, race will
happen, because reader can observe a newly allocated hash but the old size
(or vice versa). So oops will happen like follows：
BUG: unable to handle kernel NULL pointer dereference at 0000000000000017
IP: [<ffffffffa0418e21>] seq_print_acct+0x11/0x50 [nf_conntrack]
Call Trace:
[<ffffffffa0412f4e>] ? ct_seq_show+0x14e/0x340 [nf_conntrack]
[<ffffffff81261a1c>] seq_read+0x2cc/0x390
[<ffffffff812a8d62>] proc_reg_read+0x42/0x70
[<ffffffff8123bee7>] __vfs_read+0x37/0x130
[<ffffffff81347980>] ? security_file_permission+0xa0/0xc0
[<ffffffff8123cf75>] vfs_read+0x95/0x140
[<ffffffff8123e475>] SyS_read+0x55/0xc0
[<ffffffff817c2572>] entry_SYSCALL_64_fastpath+0x1a/0xa4
It is very easy to reproduce this kernel crash.
1. open one shell and input the following cmds:
while : ; do
echo $RANDOM > /sys/module/nf_conntrack/parameters/hashsize
done
2. open more shells and input the following cmds:
while : ; do
cat /proc/net/nf_conntrack
done
3. just wait a monent, oops will happen soon.
The solution in this patch is based on Florian's Commit 5e3c61f981
("netfilter: conntrack: fix lookup race during hash resize"). And
add a wrapper function nf_conntrack_get_ht to get hash and hsize
suggested by Florian Westphal.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
inet_forward_change() runs with RTNL held.
We are allowed to sleep if required.
If we use __in_dev_get_rtnl() instead of __in_dev_get_rcu(),
we no longer have to use GFP_ATOMIC allocations in
inet_netconf_notify_devconf(), meaning we are less likely to miss
notifications under memory pressure, and wont touch precious memory
reserves either and risk dropping incoming packets.
inet_netconf_get_devconf() can also use GFP_KERNEL allocation.
Fixes: edc9e74893 ("rtnl/ipv4: use netconf msg to advertise forwarding status")
Fixes: 9e5511106f ("rtnl/ipv4: add support of RTM_GETNETCONF")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the IPIP driver to support MPLS over IPv4. The implementation is an
extension of existing support for IPv4 over IPv4 and is based of multiple
inner-protocol support for the SIT driver.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
