rsmu (Renesas Synchronization Management Unit ) driver is located in
drivers/mfd and responsible for creating multiple devices including
clockmatrix phc, which will then use the exposed regmap and mutex
handle to access i2c/spi bus.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also correct how initialize_dco_operating_mode is called
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't need to support new 5.2 functions but different register
addresses
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the device initialization aligns the rising edge of the output
clock to the internal 1 PPS clock. If the system APLL and DPLL is not
locked, then the alignment will fail and there will be a fixed offset
between the internal 1 PPS clock and the output clock.
After loading the device firmware, poll the system APLL and DPLL for
locked state prior to initialization, timing out after 2 seconds.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SM_RESET device only when loading full configuration and check
for BOOT_STATUS. Also remove polling for write trigger done in
_idtcm_settime().
Changes since v1:
-Correct warnings from strict checkpatch
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1607442117-13661-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old code for i2c write would break on some controllers, which fails
at handling Repeated Start Condition. So we will just use i2c_master_send
to handle write in one transanction.
Changes since v1:
- Remove indentation change
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 4.8.7 firmware, adjtime can change delta instead of absolute time,
which greately increases snap accuracy. PPS alignment doesn't have to
be set for every single TOD change. Other minor changes includes:
adding more debug logs, increasing snap accuracy for pre 4.8.7 firmware
and supporting new tcs2bin format.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add idtcm_adjphase() to support PHC write phase mode.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IDT ClockMatrix (TM) family includes integrated devices that provide
eight PLL channels. Each PLL channel can be independently configured as a
frequency synthesizer, jitter attenuator, digitally controlled
oscillator (DCO), or a digital phase lock loop (DPLL). Typically
these devices are used as timing references and clock sources for PTP
applications. This patch adds support for the device.
Co-developed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
