In a following change, rockchip_set_mux gets the possibility to fail.
Therefore add a return value to it and honor error codes in functions
using rockchip_set_mux.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The correct value of .mux_offset for rk3188 seems to be 0x60
instead of 0x68.
Heiko adds:
GPIO0 only has the second two IOMUX registers:
- GRF_GPIO0C_IOMUX at 0x68
- GRF_GPIO0D_IOMUX at 0x6c
which I guess is where my mistake comes from.
It looks like there does no iomux register exist at all
for the first 16 pins.
In any case, the current number is wrong, and the 0x60
offset is the correct one, but I guess we need to
determine what the affected pins do - do they always have a
gpio mux or such?
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged in a branch of irqchip changes from Thomas
Gleixner: we need to have new callbacks from the
irqchip to determine if the GPIO line will be eligible
for IRQs, and this callback must be able to say "no".
After some thinking I got the branch from tglx and
have switched all current users over to use this.
- Based on tglx patches, we have added some generic
irqchip helpers in the gpiolib core. These will
help centralize code when GPIO drivers have simple
chained/cascaded IRQs. Drivers will still define
their irqchip vtables, but the gpiolib core will
take care of irqdomain set-up, mapping from local
offsets to Linux irqs, and reserve resources by
marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control
drivers have been switched over to use the new
gpiochip-to-irqchip infrastructure with more
drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth
it so it is already a win.
- A new driver for the Synopsys DesignWare APB GPIO
block.
- Modify the DaVinci GPIO driver to be reusable also
for the new TI Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level,
respecting assertion polarity through ACTIVE_LOW
flags, adding gpiod_direction_output_raw() for the
case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from
a specific offset on a certain chip inside driver
code.
- Switch ACPI GPIO code over to using
gpiochip_get_desc() and get rid of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked
after encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names
from platform data.
- We now clamp values returned from GPIO drivers to
the boolean [0,1] range.
- Some improved documentation on how to use the polarity
flag was added.
- The a large slew of incremental driver updates and
non-critical fixes. Some targeted for stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Qqf
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull bulk of gpio updates from Linus Walleij:
"A pretty big chunk of changes this time, but it has all been on
rotation in linux-next and had some testing. Of course there will be
some amount of fixes on top...
- Merged in a branch of irqchip changes from Thomas Gleixner: we need
to have new callbacks from the irqchip to determine if the GPIO
line will be eligible for IRQs, and this callback must be able to
say "no". After some thinking I got the branch from tglx and have
switched all current users over to use this.
- Based on tglx patches, we have added some generic irqchip helpers
in the gpiolib core. These will help centralize code when GPIO
drivers have simple chained/cascaded IRQs. Drivers will still
define their irqchip vtables, but the gpiolib core will take care
of irqdomain set-up, mapping from local offsets to Linux irqs, and
reserve resources by marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control drivers have been
switched over to use the new gpiochip-to-irqchip infrastructure
with more drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth it so it is
already a win.
- A new driver for the Synopsys DesignWare APB GPIO block.
- Modify the DaVinci GPIO driver to be reusable also for the new TI
Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level, respecting assertion
polarity through ACTIVE_LOW flags, adding gpiod_direction_output_raw()
for the case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from a specific
offset on a certain chip inside driver code.
- Switch ACPI GPIO code over to using gpiochip_get_desc() and get rid
of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked after
encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names from platform
data.
- We now clamp values returned from GPIO drivers to the boolean [0,1]
range.
- Some improved documentation on how to use the polarity flag was
added.
- a large slew of incremental driver updates and non-critical fixes.
Some targeted for stable"
* tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (80 commits)
gpio: rcar: Add helper variable dev = &pdev->dev
gpio-lynxpoint: force gpio_get() to return "1" and "0" only
gpio: unmap gpio irqs properly
pch_gpio: set value before enabling output direction
gpio: moxart: Actually set output state in moxart_gpio_direction_output()
gpio: moxart: Avoid forward declaration
gpio: mxs: Allow for recursive enable_irq_wake() call
gpio: samsung: Add missing "break" statement
gpio: twl4030: Remove redundant assignment
gpio: dwapb: correct gpio-cells in binding document
gpio: iop: fix devm_ioremap_resource() return value checking
pinctrl: coh901: convert driver to use gpiolib irqchip
pinctrl: nomadik: convert driver to use gpiolib irqchip
gpio: pl061: convert driver to use gpiolib irqchip
gpio: add IRQ chip helpers in gpiolib
pinctrl: nomadik: factor in platform data container
pinctrl: nomadik: rename secondary to latent
gpio: Driver for SYSCON-based GPIOs
gpio: generic: Use platform_device_id->driver_data field for driver flags
pinctrl: coh901: move irq line locking to resource callbacks
...
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the
STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung),
sunxi (AllWinner), i.MX (Freescale), Baytrail.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7Sq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk changes from Linus Walleij:
"Pin control bulk changes for the v3.15 series, no new core
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung), sunxi
(AllWinner), i.MX (Freescale), Baytrail"
* tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: tegra: add some missing Tegra114 entries
pinctrl: tegra: fix some mistakes in Tegra124
pinctrl: msm: fix up out-of-order merge conflict
pinctrl: st: Fix error check for of_irq_to_resource usage
pinctrl: tegra: consistency cleanup
pinctrl: tegra: dynamically calculate function list of groups
pinctrl: tegra: init Tegra20/30 at module_init time
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
pinctrl: st: add pinctrl support for the STiH407 SoC
pinctrl: st: Enhance the controller to manage unavailable registers
pinctrl: msm: Simplify msm_config_reg() and callers
pinctrl: msm: Remove impossible WARN_ON()s
pinctrl: msm: Replace lookup tables with math
pinctrl: msm: Drop OF_IRQ dependency
pinctrl: msm: Drop unused includes
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
pinctrl: msm: Silence recursive lockdep warning
pinctrl: mvebu: silence WARN to dev_warn
pinctrl: msm: drop wake_irqs bitmap
pinctrl-baytrail: add function mux checking in gpio pin request
...
This converts the COH901 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old platform data struct is just a leftover from the times
when the driver was not probed exclusively from the device tree.
Factor this into the general state container and simplify the
probe path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "secondary irq" in the nomadik pin control driver is actually
not secondary (as in: can occur any time alongside the ordinary
irq), it is a latent IRQ. It is an IRQ that has occurred when
the system was in sleep state and has been cached in a special
register flagged from the low power management unit (PRCM).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the COH901 GPIO driver over to using the
.request_resources() and .release_resources() callbacks from
the irqchip vtable and separate the calls from the .enable()
and .disable() callbacks as the latter cannot really say no
to a request, whereas the resource callbacks can.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches all GPIO and pin control drivers with irqchips
that were using .startup() and .shutdown() callbacks to lock
GPIO lines for IRQ usage over to using the .request_resources()
and .release_resources() callbacks just introduced into the
irqchip vtable.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some missing pin and drive group definitions to the driver. These
are all defined in the TRM, but missing from the driver for some reason.
Fix a couple of mistakes in the drive group definitions.
Much of the diff to tegra114_groups[] is an indentation change due to one
of the new group names being long. git diff/show -w will highlight this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A couple of pairs of pin group names were swapped in the table. This
caused the wrong register to be programmed. Luckily, this had little
effect, if any, since the swapped pins were likely to be programmed
identically.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 051a58b462
"pinctrl: msm: Simplify msm_config_reg() and callers"
removed the local "reg" variable in the msm_config_reg()
function, but the earlier
commit ed118a5fd9
"pinctrl-msm: Support output-{high,low} configuration"
introduced a new switchclause using it.
Fix this up by removing the offending register assignment.
Reported-by: Kbuild test robot <fengguang.wu@intel.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes an error check while using of_irq_to_resource.
of_irq_to_resource returns non-zero interrupt number on success and zero
on error. The driver was using error check is wrong way.
Without this patch the driver will configure interrupt zero if there is
no interrupt specified in the node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix Tegra30/114/124 pinmux drivers consistency issues.
* Sort all lists of the same object type (e.g. #defines for pins, and
the array that defines their names) in the same order.
* Whitespace fixes.
* Consistency in layout between the 3 drivers.
These driver files were also auto-generated, which should allow us to
make e.g. the U-Boot drivers completely consistent with the kernel in
the future:-)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The per-SoC data structures for Tegra pinctrl stored some information
in a redundant way. Specifically, the list of groups that each function
could be muxed onto was stored once explicitly, and also as part of the
definition of each group. Eliminate this redundancy, and calculate each
function's list of valid groups at pinctrl probe time. This removes
thousands of lines of code from the pinctrl driver and ~16K from the
vmlinux binary size, and adds only about 500uS to the boot process (on
Tegra30; newer SoCs will likely be faster still).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra20/30 pinctrl drivers currently initializes at arch_initcall,
whereas Tegra114/124 pinctrl drivers initialize at module_init time.
Convert Tegra20/30 to work the same way as the other drivers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch replaces the raw values with ARRAY_SIZE for assigning the
ninput_delays and noutput_delays fields of STiH416's st_pctl_data struct.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the initial support for pinctrl based on H407 SoC.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new logic inside the st pinctrl to manage
an unsupported scenario: some sysconfig are not available!
This is the case of STiH407 where, although documented, the
following registers from SYSCFG_FLASH have been removed from the SoC.
SYSTEM_CONFIG3040
Output Enable pad control for all PIO Alternate Functions
and
SYSTEM_ CONFIG3050
Pull Up pad control for all PIO Alternate Functions
Without managing this condition an imprecise external abort
will be detect.
To do this the patch also reviews the st_parse_syscfgs
and other routines to manipulate the registers only if
actually available.
In any case, for example the st_parse_syscfgs detected
an error condition but no action was made in the
st_pctl_probe_dt.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We don't need to check for a negative reg here because reg is
always the same and is always non-negative. Also, collapse the
switch statement down for the duplicate cases.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All these functions are limited in what they can pass as the gpio
or irq number to whatever is setup during probe. Remove the
checks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We don't need to waste space with these lookup tables, just do
the math directly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver doesn't rely on any functionality living in
drivers/of/irq.c to compile. Drop this dependency.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These includes are unused or can be handled via forward
declarations. Remove them.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fail the probe and print a warning if SoC specific drivers have
more GPIOs than there can be accounted for in the static bitmaps.
This should avoid silent corruption/failures in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a driver calls enable_irq_wake() on a gpio turned interrupt
from the msm pinctrl driver we'll get a lockdep warning like so:
=============================================
[ INFO: possible recursive locking detected ]
3.14.0-rc3 #2 Not tainted
---------------------------------------------
modprobe/52 is trying to acquire lock:
(&irq_desc_lock_class){-.....}, at: [<c026aea0>] __irq_get_desc_lock+0x48/0x88
but task is already holding lock:
(&irq_desc_lock_class){-.....}, at: [<c026aea0>] __irq_get_desc_lock+0x48/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by modprobe/52:
#0: (&__lockdep_no_validate__){......}, at: [<c04f2864>] __driver_attach+0x48/0x98
#1: (&__lockdep_no_validate__){......}, at: [<c04f2874>] __driver_attach+0x58/0x98
#2: (&irq_desc_lock_class){-.....}, at: [<c026aea0>] __irq_get_desc_lock+0x48/0x88
#3: (&(&pctrl->lock)->rlock){......}, at: [<c04bb4b8>] msm_gpio_irq_set_wake+0x20/0xa8
Silence it by putting the gpios into their own lock class.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl will WARN on missing DT resources, which is a little bit too
noisy. Use dev_warn with FW_BUG instead.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the wake_irqs bitmap is used to track whether there are any
gpio's which are configured as wake irqs, and uses this to determine
whether or not to call enable_irq_wake()/disable_irq_wake() on the
summary interrupt.
However, the genirq core already handles this case, by maintaining a
'wake_count' per irq_desc, and only calling into the controlling
irq_chip when wake_count transitions 0 <-> 1.
Drop this bitmap, and unconditionally call irq_set_irq_wake() on the
summary interrupt.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The requested gpio pin must has the func_pin_mux field set
to GPIO function by BIOS/FW in advanced. Else, the gpio pin
request would fail. This is to ensure that we do not expose
any gpio pins which shall be used for alternate functions,
for eg: wakeup pin, I/O interfaces for LPSS, etc.
Signed-off-by: Chew, Kean Ho <kean.ho.chew@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drive_dev3_pins in pinctrl-tegra114.c wasn't used; delete it.
pinctrl-tegra124.c had quite a few typos. Fix those.
pinctrl-tegra124.c had a few mismatches between the *_groups[] ararys
and the function lists in tegra124_groups[]. Fix those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A collection of fixes for ARM platforms. A little large due to us missing to
do one last week, but there's nothing in particular here that is in itself
large and scary.
Mostly a handful of smaller fixes all over the place. The majority is made
up of fixes for OMAP, but there are a few for others as well. In particular,
there was a decision to rename a binding for the Broadcom pinctrl block that
we need to go in before the final release since we then treat it as ABI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=YBim
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Fix the SD1_CLK handling for r8a7791. Without this patch
it is impossible to request all pins needed for SDHI1 on
the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modular builds of pinctrl-msm break due to handle_bad_irq being
unexported for module use. For now, make PINCTRL_MSM 'bool'.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixing setting the interrupt type for eints >= 8.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On tha Allwinner A20 SoC, the external interrupts on the pin controller
device are connected to the GIC. Without chained_irq_{enter, exit},
external GPIO interrupts, such as used by mmc core card detect, cause
the system to hang.
This issue was first encountered during my attempt to get out-of-band
interrupts for WiFi on the Cubietruck working. With David's new series
of sunci-mci using mmc slot-gpio for (GPIO interrupt based) card
detection, removing the SD card also causes my Cubietruck to hang. This
problem should extend to all Allwinner A20 based boards.
With this fix, the system no longer hangs when I remove or insert the
SD card. /proc/interrupts show that the interrupt has correctly fired.
However the system still does not detect card removal/insertion. I
believe this is another unrelated issue.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a regmap for global registers, get rid of the last
remaining hardcoded physical addresses. While at it, also remove
DOVE_ prefix from those macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have ioremapped pmu_mpp registers, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have an ioremapped mpp4 register, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have ioremapped mpp base registers, get rid of hardcoded
physical addresses. While at it, also remove DOVE_ prefix from those
macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Dove pinctrl uses some global config registers to control pins.
This patch requests a syscon regmap for those registers. As this
changes DT to driver requirements, fallback to a self-registered
regmap with hardcoded resources, if the corresponding syscon DT
node is missing. Also, WARN about old DT binding usage to encourage
users to update their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Dove pinctrl also requires additional registers to control all pins.
This patch requests resources for mpp4 and pmu-mpp register ranges.
As this changes DT to driver requirements, fallback to hardcoded
resources, if the corresponding DT regs have not been set.
Also, WARN about old DT binding usage to encourage users to update
their DTBs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Armada 380/385 are new ARM SoCs from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Armada 375 is a new ARM SoC from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Dove has pins that can be switched between normal and pmu functions.
Rework pmu_mpp callbacks to reuse default mpp ctrl helpers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Passing a NULL name for pin ranges will auto-generate standard names
for each pin. With common pinctrl driver now checking NULL name correctly,
consolidate mpp pins 0-15.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Now that each per-SoC pinctrl driver must implement its own get/set
functions, there is no point in keeping the MPP_REG_CTRL macro, whose
purpose was to let the core pinctrl mvebu driver use default get/set
functions. While at it also update the comment about mvebu_mpp_ctrl.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With every SoC always providing its own get/set callbacks, we can now
remove the generic ones, remove the obsolete base address, and always
use the provided callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The way that mvebu pinctrl is designed, requesting mpp registers
in common pinctrl driver does not allow SoC specific drivers to
access this resource.
Move resource allocation in each SoC pinctrl driver and enable
already provided mpp_{set,get} callbacks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
We want to get rid of passing register addresses to common pinctrl
driver, so provide set/get callbacks that use generic mpp pins helper
and will be used later. While at it, also make use of globally defined
MPP macros.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This adds some defines and helper functions for the common mpp reg
layout to mvebu pinctrl include.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
The only valuable information a special callback can derive from
mvebu_mpp_ctrl passed to it, is the pin id. Instead of passing
the struct, pass the pid directly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We treat unnamed controls as generic mvebu mpp register controls but
we identify them by not being special controls. Flip the logic and
use the name pointer as identification instead. While at it, add some
comments explaining the not so obvious treatment.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the introduction of a global name buffer, we can now remove
the allocation and preparation of per-control name buffers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
pinctrl-mvebu allows SoCs to pass unnamed controls that will get an
auto-generated name of "mpp<PIN#>". Currently, we are allocating name
buffers on a per-control basis while looping over passed controls.
This counts the total number of unnamed controls and allocates a
global name buffer instead. The new buffer is then used while assigning
controls to pinctrl groups later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is needed for gpiod_get_direction().
Otherwise, it returns -EINVAL.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The wrong index counter was being used, causing the debug message
to show an incorrect pin name.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The correct value for selecting the mmc0 function on port F pins is 2 not 4,
as per the data-sheet:
http://dl.linux-sunxi.org/A13/A13%20Datasheet%20-%20v1.12%20%282012-03-29%29.pdf
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The data pins of some peripheral are different if connecting to different
devices in one pinmux function. In the PPI case, data pins can be used
in 8, 16 and 24 pin groups individually. Add these groups into one ppi
function.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the SIMPLE_DEV_PM_OPS macro and convert to the modern pm ops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The static suspend/resume functions were not being used while
!CONFIG_PM. Fix it and convert to CONFIG_PM_SLEEP.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin, group and function definitions for SPI#8
controller.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bring the driver in line with the bcm-based dt name for pinctrl.
This is being done to keep consistency with other Broadcom mobile
SoC drivers.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
On systems which were not booted using DT it is entirely unsurprising that
device nodes don't have any DT information and this is going to happen for
every single device in the system. Make pinctrl be less chatty about this
situation by only logging in the case where we have DT.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a new group for the USB0 OVC/VBUS pin by itself. This
allows us to monitor PWEN as GPIO on the Lager board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl support for all platforms based on EXYNOS5260 SoC.
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Young-Gun Jang <yg1004.jang@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for configuring pins as output with value as from the
pinconf-generic interface.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
commit 8385af02ba only added this group for prima2, and missed
atlas6. This patch fixes it.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Negative irq_base means this gpio port doens't support interrupts.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is better to keep this structure in the pinctrl-adi2 driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A QSPI function set consists of 3 groups:
- qspi_ctrl (2 control wires)
- qspi_data2 (2 data wires, for Single/Dual SPI)
- qspi_data4 (4 data wires, for Quad SPI)
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
ST pin controller does not have hardware support for detecting edge
triggered interrupts, It only has level triggering support.
This patch attempts to fake up edge triggers from hw level trigger
support in software. With this facility now the gpios can be easily used
for keypads, otherwise it would be difficult for drivers like keypads to
work with level trigger interrupts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add interrupt support to the pincontroller driver.
ST Pincontroller GPIO bank can have one of the two possible types of
interrupt-wirings.
First type is via irqmux, single interrupt is used by multiple gpio
banks. This reduces number of overall interrupts numbers required. All
these banks belong to a single pincontroller.
_________
| |----> [gpio-bank (n) ]
| |----> [gpio-bank (n + 1)]
[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
| |----> [gpio-bank (... )]
|_________|----> [gpio-bank (n + 7)]
Second type has a dedicated interrupt per gpio bank.
[irqN]----> [gpio-bank (n)]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit c420619 "pinctrl: pinconf: remove checks on ops->pin_config_get"
removed the check on (ops != NULL) when performing pinconf_pins_show() or
pinconf_groups_show(). As these entries are always enabled, even if
pinconf is not supported, reading will result in an oops due to NULL
ops.
Instead of checking for ops, remove the corresponding debugfs entries if
pinconf and/or pinmux are not implemented.
Tested on OMAP3 (pinctrl-single).
Cc: stable@vger.kernel.org
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have few fedora bug reports about list corruption on pinctrl,
for example:
https://bugzilla.redhat.com/show_bug.cgi?id=1051918
Most likely corruption happen due lack of protection of pinctrl_list
when adding new nodes to it. Patch corrects that.
Fixes: 42fed7ba44 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
according to datasheet and ac97_muxmask assignment, ac97_pins should be
corrected.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset for the 2bit register calculate wrong, this patch
fixes the problem. The debugfs printout for oconf, iconfa, iconfb
now shows the real values.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to an assumption in the VT8500 pinctrl driver, the value passed
from devicetree for 'wm,pull' was not explicitly translated before
being passed to pinconf.
Since v3.10, changes to 'enum pin_config_param', PIN_CONFIG_BIAS_PULL_(UP/DOWN)
no longer map 1-to-1 with the expected values in devicetree.
This patch adds a small translation between the devicetree values (0..2)
and the enum pin_config_param equivalent values.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset to ICONFB was incorrect, this patch set the correct value 0x14.
dev_dbg in function imx1_write_2bit print the wrong address and had been
moved after address calculation.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When setting the gpio irq type, use the __irq_set_handler_locked()
variant instead of the irq_set_handler() to prevent false
spinlock recursion warning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # v3.12
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
- New driver for the Qualcomm TLMM pin controller and its
msm8x74 subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and
GPIO drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf
driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC"
driver and associated subdrivers as usual. It is settling
down a little bit now it seems.
- Minor fixes and incremental updates here and there as usual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ol2E
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All instances of this device are now coming from device tree-
enabled platforms probing without using platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.
Fixes: f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As this driver is using pinconf_generic_dt_node_to_map_pin() it
needs to depend on OF so as not to cause build problems on
archs that do not support OF.
Cc: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Probe function had commas instead of semi-colons on some of the lines.
This patch just fixes those lines. No functional chagnes done in this
patch.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Also assign the gpio_chip.dev pointer to be used for error
messages.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
busses like i2c, spi and so on can parse the virq of their subnode automatically by
irq_of_parse_and_map(). for example, i2c will do that in of_i2c_register_devices().
people can put hwirq number attached to a gpio controller in dts, and drivers can
directly request the parsed virq.
for example, for an i2c client as below,
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
interrupt-parent = <&gpio>;
interrupts = <3 0>;
reg = <0x5c>;
};
in i2c client probe(), it will request_irq(client->irq, ...) without
calling gpio_direction_input().
so here when we set irq type, we also put the pin to input direction.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in sirfsoc gpio probe(), we create 5 irq_domains for 5 gpio banks. but
in irq_create_of_mapping() of irqchip core level, irq_find_host() can
only return the 1st irq_domain attached the pinctrl dt device node as
we can see from the codes:
unsigned int irq_create_of_mapping(struct device_node *controller,
const u32 *intspec, unsigned int intsize)
{
struct irq_domain *domain;
...
domain = controller ? irq_find_host(controller) : irq_default_domain;
}
struct irq_domain *irq_find_host(struct device_node *node)
{
struct irq_domain *h, *found = NULL;
int rc;
/* We might want to match the legacy controller last since
* it might potentially be set to match all interrupts in
* the absence of a device node. This isn't a problem so far
* yet though...
*/
mutex_lock(&irq_domain_mutex);
list_for_each_entry(h, &irq_domain_list, link) {
if (h->ops->match)
rc = h->ops->match(h, node);
else
rc = (h->of_node != NULL) && (h->of_node == node);
if (rc) {
found = h;
break;
}
}
mutex_unlock(&irq_domain_mutex);
return found;
}
for sirfsoc, the 1st irq_domain attached to the device_node(controller) only
can do linear for the 1st 32 gpios. so for devices who use gpio hwirq above
32 and put the information in dt like:
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
+ interrupt-parent = <&gpio>;
+ interrupts = <34 0>;
};
we will fail to get the virq for these devices as hwirq will be bigger than
domain->revmap_data.linear.size in:
unsigned int irq_linear_revmap(struct irq_domain *domain,
irq_hw_number_t hwirq)
{
/* Check revmap bounds; complain if exceeded */
if (WARN_ON(hwirq >= domain->revmap_data.linear.size))
return 0;
return domain->revmap_data.linear.revmap[hwirq];
}
this patch drops redundant irq_domain and keep only one to fix the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 4e7e8017a8 (pinctrl: pinctrl-single:
enhance to configure multiple pins of different modules) improved
support for pinctrl-single,bits option, but also caused a regression
in parsing badly configured mask data.
If the masks in DT data are not quite right,
pcs_parse_bits_in_pinctrl_entry() can end up in an infinite loop,
trashing memory at the same time.
Add a check to verify that each loop actually removes bits from the
'mask', so that the loop can eventually end.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pcs_enable() uses vals->mask instead of pcs->fmask when bits_per_mux is
enabled. However, pcs_disable() always uses pcs->fmask.
Fix pcs_disable() to use vals->mask with bits_per_mux.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If pins are used for function output like pwm, clk32k,
power good etc then set it as output mode default.
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit af614b2301 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the clock output pin functions on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds VIN[0-2] pinmux support to r8a7791 SoC.
VIN1 B mirror is also added along with the primary
configuration since it's the only one that provides
access to all 24 data bits on VIN1.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This groups USB PWEN and OVC pins together on R8A7791 SoC,
the same way it's done on R8A7790, since both are needed
for a USB device.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The enum_ids and var_field_width fields of struct pinmux_data_reg and
pinmux_cfg_reg are initialized using compound literals. Cast them to
const to store them in .rodata.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set g->out_bit bit for gpio output high, clear g->out_bit bit for gpio output
low.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the clk_prepare and clk_enable calls by a single
clk_prepare_enable call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clk_unprepare shall be called before clk_disable.
Fix the issue by replacing the clk_unprepare and clk_disable calls by a
single clk_disable_unprepare call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the more specific form 8974 for the compatible to reduce the
risk of future mishaps.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the bitmaps part of the msm_pinctrl allocation instead of
separately allocating them.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIOLIB and OF as dependencies for PINCTRL_MSM8X74, to fix
build errors from i386-randconfig.
Also add help text and make the entries tristate, while touching
these entries.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[Rebased on top of pin control development branch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to get the pin configuration by using debugfs. On my system:
# cat /sys/kernel/debug/pinctrl/pinctrl.3/pinconf-pins
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's more than one window, name the field windows.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes catching duplicate entries easier. Merge the two IRQ9 entries
found after sorting.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The external IRQ15 input multiplexed on GPIO 0 is missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some indices take positive values only, make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ops->pin_config_get() is only used in one specific path that will only be taken
for generic pinconf drivers (ops->is_generic == true) when dumping the pinconf
by using debugfs.
By removing the check in pinconf_check_ops(), let's stop pressuring people to
write a pin_config_get() function that will never be used and so will probably
never be tested.
Removing the check in pinconf_pins_show() allows driver to not implement
pin_config_get() but still get a dump of the pinconf in debugfs by implementing
pin_config_dbg_show().
Finally, not implementing pin_config_get() now results in returning -ENOTSUPP
instead of -EINVAL. While this doesn't have any real impact for now, this feels
more right.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
