Introduce a temporary variable to check for an invalid configuration
attempt from user space. Before this patch the value was copied to
the real config variable and rolled back in the case of an error.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230203090807.97100-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A CAN XL device is always capable to process CAN FD frames. The former
check when sending CAN FD frames relied on the existence of a CAN FD
device and did not check for a CAN XL device that would be correct
too.
With this patch the CAN FD feature is enabled automatically when CAN
XL is switched on - and CAN FD cannot be switch off while CAN XL is
enabled.
This precondition also leads to a clean up and reduction of checks in
the hot path in raw_rcv() and raw_sendmsg(). Some conditions are
reordered to handle simple checks first.
changes since v1: https://lore.kernel.org/all/20230131091012.50553-1-socketcan@hartkopp.net
- fixed typo: devive -> device
changes since v2: https://lore.kernel.org/all/20230131091824.51026-1-socketcan@hartkopp.net/
- reorder checks in if statements to handle simple checks first
Fixes: 626332696d ("can: raw: add CAN XL support")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230131105613.55228-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for SO_MARK to the CAN_RAW protocol. This makes it
possible to add traffic control filters based on the fwmark.
Link: https://lore.kernel.org/all/20221210113653.170346-1-mkl@pengutronix.de
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable CAN_RAW sockets to read and write CAN XL frames analogue to the
CAN FD extension (new CAN_RAW_XL_FRAMES sockopt).
A CAN XL network interface is capable to handle Classical CAN, CAN FD and
CAN XL frames. When CAN_RAW_XL_FRAMES is enabled, the CAN_RAW socket checks
whether the addressed CAN network interface is capable to handle the
provided CAN frame.
In opposite to the fixed number of bytes for
- CAN frames (CAN_MTU = sizeof(struct can_frame))
- CAN FD frames (CANFD_MTU = sizeof(struct can_frame))
the number of bytes when reading/writing CAN XL frames depends on the
number of data bytes. For efficiency reasons the length of the struct
canxl_frame is truncated to the needed size for read/write operations.
This leads to a calculated size of CANXL_HDR_SIZE + canxl_frame::len which
is enforced on write() operations and guaranteed on read() operations.
NB: Valid length values are 1 .. 2048 (CANXL_MIN_DLEN .. CANXL_MAX_DLEN).
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-8-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now, register notifier after register proto successfully. It can create
raw socket and set socket options once register proto successfully, so it
is possible missing notifier event before register notifier successfully
although this is a low probability scenario.
Move notifier registration to the front of proto registration like done
in j1939. In addition, register_netdevice_notifier() may fail, check its
result is necessary.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/7af9401f0d2d9fed36c1667b5ac9b8df8f8b87ee.1661584485.git.william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch calls into sock_cmsg_send() to parse the user supplied
control information into a struct sockcm_cookie. Then assign the
requested transmit time to the skb.
This makes it possible to use the Earliest TXTIME First (ETF) packet
scheduler with the CAN_RAW protocol. The user can send a CAN_RAW frame
with a TXTIME and the kernel (with the ETF scheduler) will take care
of sending it to the network interface.
Link: https://lore.kernel.org/all/20220502091946.1916211-3-mkl@pengutronix.de
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skb in raw_sendmsg() is allocated with sock_alloc_send_skb(),
which subsequently calls sock_alloc_send_pskb() -> skb_set_owner_w(),
which assigns "skb->sk = sk".
This patch removes the not needed setting of skb->sk.
Link: https://lore.kernel.org/all/20220502091946.1916211-2-mkl@pengutronix.de
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adding a new socket option, SO_RCVMARK, to indicate that SO_MARK
should be included in the ancillary data returned by recvmsg().
Renamed the sock_recv_ts_and_drops() function to sock_recv_cmsgs().
Signed-off-by: Erin MacNeil <lnx.erin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220427200259.2564-1-lnx.erin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skb_recv_datagram() has two parameters 'flags' and 'noblock' that are
merged inside skb_recv_datagram() by 'flags | (noblock ? MSG_DONTWAIT : 0)'
As 'flags' may contain MSG_DONTWAIT as value most callers split the 'flags'
into 'flags' and 'noblock' with finally obsolete bit operations like this:
skb_recv_datagram(sk, flags & ~MSG_DONTWAIT, flags & MSG_DONTWAIT, &rc);
And this is not even done consistently with the 'flags' parameter.
This patch removes the obsolete and costly splitting into two parameters
and only performs bit operations when really needed on the caller side.
One missing conversion thankfully reported by kernel test robot. I missed
to enable kunit tests to build the mctp code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a function wrapper to call the sk_error_report
callback. That will prepare to add additional handling whenever
sk_error_report is called, for example to trace socket errors.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.
Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.
Link: https://syzkaller.appspot.com/bug?id=391b9498827788b3cc6830226d4ff5be87107c30 [1]
Link: https://syzkaller.appspot.com/bug?id=1724d278c83ca6e6df100a2e320c10d991cf2bce [2]
Link: https://lore.kernel.org/r/54a5f451-05ed-f977-8534-79e7aa2bcc8f@i-love.sakura.ne.jp
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: syzbot <syzbot+355f8edb2ff45d5f95fa@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+0f1827363a305f74996f@syzkaller.appspotmail.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: syzbot <syzbot+355f8edb2ff45d5f95fa@syzkaller.appspotmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit f5223e9eee ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.
The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.
Fixes: f5223e9eee ("can: extend sockaddr_can to include j1939 members")
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t
Link: https://lore.kernel.org/r/20210325125850.1620-1-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Multiple filters (struct can_filter) can be set with the setsockopt()
function, which was originally intended as a write-only operation.
As getsockopt() also provides a CAN_RAW_FILTER option to read back the
given filters, the caller has to provide an appropriate user space buffer.
In the case this buffer is too small the getsockopt() silently truncates
the filter information and gives no information about the needed space.
This is safe but not convenient for the programmer.
In net/core/sock.c the SO_PEERGROUPS sockopt had a similar requirement
and solved it by returning -ERANGE in the case that the provided data
does not fit into the given user space buffer and fills the required size
into optlen, so that the caller can retry with a matching buffer length.
This patch adopts this approach for CAN_RAW_FILTER getsockopt().
Reported-by: Phillip Schichtel <phillip@schich.tel>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-By: Phillip Schichtel <phillip@schich.tel>
Link: https://lore.kernel.org/r/20201216174928.21663-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Error queue are not yet implemented in CAN-raw sockets.
The problem: a userland call to recvmsg(soc, msg, MSG_ERRQUEUE) on a
CAN-raw socket would unqueue messages from the normal queue without
any kind of error or warning. As such, it prevented CAN drivers from
using the functionalities that relies on the error queue such as
skb_tx_timestamp().
SCM_CAN_RAW_ERRQUEUE is defined as the type for the CAN raw error
queue. SCM stands for "Socket control messages". The name is inspired
from SCM_J1939_ERRQUEUE of include/uapi/linux/can/j1939.h.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20200926162527.270030-1-mailhol.vincent@wanadoo.fr
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The "WITH Linux-syscall-note" exception is intended for UAPI headers.
See LICENSES/exceptions/Linux-syscall-note
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200403073741.18352-1-masahiroy@kernel.org
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of this structure will be increased with J1939 support. To stay
binary compatible, the CAN_REQUIRED_SIZE macro is introduced for
existing CAN protocols.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the raw_sock_no_ioctlcmd() function as static as it's
only used in this source file.
Fixes: 473d924d7d ("can: fix ioctl function removal")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch balances the braces around else statements, so that
checkpatch doesn't complain anymore.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes unnecessary blank lines, and adds suggested ones, so
that checkpatch doesn't complain anymore.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 60649d4e0a ("can: remove obsolete empty ioctl() handler") replaced the
almost empty can_ioctl() function with sock_no_ioctl() which always returns
-EOPNOTSUPP.
Even though we don't have any ioctl() functions on socket/network layer we need
to return -ENOIOCTLCMD to be able to forward ioctl commands like SIOCGIFINDEX
to the network driver layer.
This patch fixes the wrong return codes in the CAN network layer protocols.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 60649d4e0a ("can: remove obsolete empty ioctl() handler")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing SPDX identifiers for the CAN network layer and correct the SPDX
license for two of its include files to make sure the BSD-3-Clause applies
for the entire subsystem.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With commit c7cbdbf29f ("net: rework SIOCGSTAMP ioctl handling") the only
ioctl function in can_ioctl() has been removed.
As this SIOCGSTAMP ioctl command is now handled in net/socket.c we can entirely
remove the CAN specific ioctl functions.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The SIOCGSTAMP/SIOCGSTAMPNS ioctl commands are implemented by many
socket protocol handlers, and all of those end up calling the same
sock_get_timestamp()/sock_get_timestampns() helper functions, which
results in a lot of duplicate code.
With the introduction of 64-bit time_t on 32-bit architectures, this
gets worse, as we then need four different ioctl commands in each
socket protocol implementation.
To simplify that, let's add a new .gettstamp() operation in
struct proto_ops, and move ioctl implementation into the common
sock_ioctl()/compat_sock_ioctl_trans() functions that these all go
through.
We can reuse the sock_get_timestamp() implementation, but generalize
it so it can deal with both native and compat mode, as well as
timeval and timespec structures.
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/lkml/CAK8P3a038aDQQotzua_QtKGhq8O9n+rdiz2=WDCp82ys8eUT+A@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets.
But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN.
Add skb_setup_tx_timestamp that configures both tx_flags and tskey
for these paths that do not need corking or use bytestream keys.
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the socket is CAN FD enabled it can handle CAN FD frame
transmissions. Add an additional check in raw_sendmsg() as a CAN2.0 CAN
driver (non CAN FD) should never see a CAN FD frame. Due to the commonly
used can_dropped_invalid_skb() function the CAN 2.0 driver would drop
that CAN FD frame anyway - but with this patch the user gets a proper
-EINVAL return code.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now CAN raw's bind() doesn't check if the can_familiy in the
struct sockaddr_can is set to AF_CAN. This patch adds the missing check.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds initial support for network namespaces. The changes only
enable support in the CAN raw, proc and af_can code. GW and BCM still
have their checks that ensure that they are used only from the main
namespace.
The patch boils down to moving the global structures, i.e. the global
filter list and their /proc stats, into a per-namespace structure and passing
around the corresponding "struct net" in a lot of different places.
Changes since v1:
- rebased on current HEAD (2bfe01e)
- fixed overlong line
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Zhang Yanmin reported crashes [1] and provided a patch adding a
synchronize_rcu() call in can_rx_unregister()
The main problem seems that the sockets themselves are not RCU
protected.
If CAN uses RCU for delivery, then sockets should be freed only after
one RCU grace period.
Recent kernels could use sock_set_flag(sk, SOCK_RCU_FREE), but let's
ease stable backports with the following fix instead.
[1]
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81495e25>] selinux_socket_sock_rcv_skb+0x65/0x2a0
Call Trace:
<IRQ>
[<ffffffff81485d8c>] security_sock_rcv_skb+0x4c/0x60
[<ffffffff81d55771>] sk_filter+0x41/0x210
[<ffffffff81d12913>] sock_queue_rcv_skb+0x53/0x3a0
[<ffffffff81f0a2b3>] raw_rcv+0x2a3/0x3c0
[<ffffffff81f06eab>] can_rcv_filter+0x12b/0x370
[<ffffffff81f07af9>] can_receive+0xd9/0x120
[<ffffffff81f07beb>] can_rcv+0xab/0x100
[<ffffffff81d362ac>] __netif_receive_skb_core+0xd8c/0x11f0
[<ffffffff81d36734>] __netif_receive_skb+0x24/0xb0
[<ffffffff81d37f67>] process_backlog+0x127/0x280
[<ffffffff81d36f7b>] net_rx_action+0x33b/0x4f0
[<ffffffff810c88d4>] __do_softirq+0x184/0x440
[<ffffffff81f9e86c>] do_softirq_own_stack+0x1c/0x30
<EOI>
[<ffffffff810c76fb>] do_softirq.part.18+0x3b/0x40
[<ffffffff810c8bed>] do_softirq+0x1d/0x20
[<ffffffff81d30085>] netif_rx_ni+0xe5/0x110
[<ffffffff8199cc87>] slcan_receive_buf+0x507/0x520
[<ffffffff8167ef7c>] flush_to_ldisc+0x21c/0x230
[<ffffffff810e3baf>] process_one_work+0x24f/0x670
[<ffffffff810e44ed>] worker_thread+0x9d/0x6f0
[<ffffffff810e4450>] ? rescuer_thread+0x480/0x480
[<ffffffff810ebafc>] kthread+0x12c/0x150
[<ffffffff81f9ccef>] ret_from_fork+0x3f/0x70
Reported-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This socket option joines the given CAN filters in the way that only CAN frames
are passed to user space that matched *all* given CAN filters. The semantic for
the applied filters is therefore changed to a logical AND.
This is useful especially when the filterset is a combination of filters where
the CAN_INV_FILTER flag is set in order to notch single CAN IDs or CAN ID
ranges from the incoming traffic.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This patch makes sure that every CAN frame which is filtered for a specific
socket is only delivered once to the user space. This is independent from the
number of matching CAN filters of this socket.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several CAN modules use a design pattern with a banner[] variable at the
top which defines a string that is used once during init to print the
banner. The string is also embedded with KERN_INFO which makes it
printk() specific.
Improve the code by eliminating the banner[] variable and moving the
string to where it is printed. Then switch from printk(KERN_INFO to
pr_info() for the lines that were changed.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
