Core & protocols
----------------
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps etc.)
lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core
instead of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length
and budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global config
variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug
of ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for
use on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code
--------------------------------------------
- Enforce VM_IOREMAP flag and range in ioremap_page_range and introduce
VM_SPARSE kind and vm_area_[un]map_pages (used by bpf_arena).
- Rework selftest harness to enable the use of the full range of
ksft exit code (pass, fail, skip, xfail, xpass).
Netfilter
---------
- Allow userspace to define a table that is exclusively owned by a daemon
(via netlink socket aliveness) without auto-removing this table when
the userspace program exits. Such table gets marked as orphaned and
a restarting management daemon can re-attach/regain ownership.
- Speed up element insertions to nftables' concatenated-ranges set type.
Compact a few related data structures.
BPF
---
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between BPF
program and user space where structures inside the arena can have
pointers to other areas of the arena, and pointers work seamlessly
for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the verifier
and the program. The verifier allows the program to loop assuming it's
behaving well, but reserves the right to terminate it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF objects.
Wireless
--------
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API
----------
- Major overhaul of the Energy Efficient Ethernet internals to support
new link modes (2.5GE, 5GE), share more code between drivers
(especially those using phylib), and encourage more uniform behavior.
Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc
----
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions,
and packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message encapsulation
or "Netlink polymorphism", where interpretation of nested attributes
depends on link type, classifier type or some other "class type".
Drivers
-------
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic
on CAN BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO) support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oY52
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps
etc) lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core instead
of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length and
budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global
config variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug of
ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for use
on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code:
- Enforce VM_IOREMAP flag and range in ioremap_page_range and
introduce VM_SPARSE kind and vm_area_[un]map_pages (used by
bpf_arena).
- Rework selftest harness to enable the use of the full range of ksft
exit code (pass, fail, skip, xfail, xpass).
Netfilter:
- Allow userspace to define a table that is exclusively owned by a
daemon (via netlink socket aliveness) without auto-removing this
table when the userspace program exits. Such table gets marked as
orphaned and a restarting management daemon can re-attach/regain
ownership.
- Speed up element insertions to nftables' concatenated-ranges set
type. Compact a few related data structures.
BPF:
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between
BPF program and user space where structures inside the arena can
have pointers to other areas of the arena, and pointers work
seamlessly for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the
verifier and the program. The verifier allows the program to loop
assuming it's behaving well, but reserves the right to terminate
it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops
type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF
firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF
objects.
Wireless:
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API:
- Major overhaul of the Energy Efficient Ethernet internals to
support new link modes (2.5GE, 5GE), share more code between
drivers (especially those using phylib), and encourage more
uniform behavior. Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from
drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc:
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions, and
packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message
encapsulation or "Netlink polymorphism", where interpretation of
nested attributes depends on link type, classifier type or some
other "class type".
Drivers:
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic on CAN
BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO)
support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs
to have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro"
* tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2255 commits)
nexthop: Fix splat with CONFIG_DEBUG_PREEMPT=y
nexthop: Fix out-of-bounds access during attribute validation
nexthop: Only parse NHA_OP_FLAGS for dump messages that require it
nexthop: Only parse NHA_OP_FLAGS for get messages that require it
bpf: move sleepable flag from bpf_prog_aux to bpf_prog
bpf: hardcode BPF_PROG_PACK_SIZE to 2MB * num_possible_nodes()
selftests/bpf: Add kprobe multi triggering benchmarks
ptp: Move from simple ida to xarray
vxlan: Remove generic .ndo_get_stats64
vxlan: Do not alloc tstats manually
devlink: Add comments to use netlink gen tool
nfp: flower: handle acti_netdevs allocation failure
net/packet: Add getsockopt support for PACKET_COPY_THRESH
net/netlink: Add getsockopt support for NETLINK_LISTEN_ALL_NSID
selftests/bpf: Add bpf_arena_htab test.
selftests/bpf: Add bpf_arena_list test.
selftests/bpf: Add unit tests for bpf_arena_alloc/free_pages
bpf: Add helper macro bpf_addr_space_cast()
libbpf: Recognize __arena global variables.
bpftool: Recognize arena map type
...
Move from simple ida to xarray for storing and loading the ptp_clock
pointer. This prepares support for future hardware timestamp selection by
being able to link the ptp clock index to its pointer.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240311144730.1239594-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the ptp_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240305-ptp-v1-1-ed253eb33c20@marliere.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240304091325.717546-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding support for the Adva timecard.
The card uses different drivers to provide access to the
firmware SPI flash (Altera based).
Other parts of the code are the same and could be reused.
Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20240205153046.3642-1-maimon.sagi@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The clocksource pointer in struct system_counterval_t is not evaluated any
more. Remove the code setting the member, and the member itself.
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240201010453.2212371-8-peter.hilber@opensynergy.com
Identify the clocksources used by ptp_kvm by setting the clocksource ID
enum constants. This avoids dereferencing struct clocksource. Once the
system_counterval_t.cs member will be removed, this will also avoid the
need to obtain clocksource pointers from kvm_arch_ptp_get_crosststamp().
The clocksource IDs are associated to timestamps requested from the KVM
hypervisor, so the proper clocksource ID is known at the ptp_kvm request
site.
While at it, also make the ptp_kvm_get_time_fn() 'ret' variable type int as
that's what the function return value is.
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240201010453.2212371-6-peter.hilber@opensynergy.com
Add a clocksource ID for the x86 kvmclock.
Also, for ptp_kvm, set the recently added struct system_counterval_t member
cs_id to the clocksource ID (x86 kvmclock or ARM Generic Timer). In the
future, get_device_system_crosststamp() will compare the clocksource ID in
struct system_counterval_t, rather than the clocksource.
For now, to avoid touching too many subsystems at once, extract the
clocksource ID from the clocksource. The clocksource dereference will be
removed once everything is converted over..
Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240201010453.2212371-5-peter.hilber@opensynergy.com
Pass additional argunent status_error over lock_status_get()
so drivers can fill it up. In case they do, expose the value over
previously introduced attribute to user. Do it only in case the
current lock_status is either "unlocked" or "holdover".
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RENESAS FemtoClock3 Wireless is a high-performance jitter attenuator,
frequency translator, and clock synthesizer. The device is comprised of 3
digital PLLs (DPLL) to track CLKIN inputs and three independent low phase
noise fractional output dividers (FOD) that output low phase noise clocks.
FemtoClock3 supports one Time Synchronization (Time Sync) channel to enable
an external processor to control the phase and frequency of the Time Sync
channel and to take phase measurements using the TDC. Intended applications
are synchronization using the precision time protocol (PTP) and
synchronization with 0.5 Hz and 1 Hz signals from GNSS.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is for the PHC devices that can measure the phase offset
between PHC signal and the external signal, such as the 1PPS signal of
GNSS. Reporting PTP_CLOCK_EXTOFF to user space will be piggy-backed to
the existing ptp_extts_event so that application such as ts2phc can
poll the external offset the same way as extts. Hence, ts2phc can use
the offset to achieve the alignment between PHC and the external signal
by the help of either SW or HW filters.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
> ./drivers/ptp/ptp_sysfs.c:27:8-16: WARNING: please use sysfs_emit
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240125015329.123023-1-lizhijian@fujitsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need to have an intermediate functions as DEFINE_RES_*()
macros are represented by compound literals. Just use them in place.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unregistering the DPLL subsystem the priv pointer is different then
the one used for registration which cause failure in unregistering.
Fixes: 09eeb3aecc ("ptp_ocp: implement DPLL ops")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode supported is currently reported to the user exactly the same, as
the current mode. That's because mode changing is not implemented.
Remove the leftover mode_supported() op and use mode_get() to fill up
the supported mode exposed to user.
One, if even, mode changing is going to be introduced, this could be
very easily taken back. In the meantime, prevent drivers form
implementing this in wrong way (as for example recent netdevsim
implementation attempt intended to do).
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHYs hwtstamp callback are still getting the timestamp config from
ifreq and using copy_from/to_user.
Get rid of these functions by using timestamp configuration in parameter.
This also allow to move on to kernel_hwtstamp_config and be similar to
net devices using the new ndo_hwstamp_get/set.
This adds the possibility to manipulate the timestamp configuration
from the kernel which was not possible with the copy_from/to_user.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I was working on a syzbot report, I found that KCSAN would
probably complain that reading q->head or q->tail without
barriers could lead to invalid results.
Add corresponding READ_ONCE() and WRITE_ONCE() to avoid
load-store tearing.
Fixes: d94ba80ebb ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20231109174859.3995880-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 8a4f030dbc.
Richard says:
The test itself is harmless, but keeping it will make people think,
"oh this pointer can be invalid."
In fact the core stack ensures that ioctl() can't be invoked after
release(), otherwise Bad Stuff happens.
Fixes: 8a4f030dbc ("ptp: Fixes a null pointer dereference in ptp_ioctl")
Link: https://lore.kernel.org/all/ZVAf_qdRfDAQYUt-@hoboy.vegasvil.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzkaller found a null pointer dereference in ptp_ioctl
originating from the lack of a null check for tsevq.
```
general protection fault, probably for non-canonical
address 0xdffffc000000020b: 0000 [#1] PREEMPT SMP KASAN
KASAN: probably user-memory-access in range
[0x0000000000001058-0x000000000000105f]
CPU: 0 PID: 5053 Comm: syz-executor353 Not tainted
6.6.0-syzkaller-10396-g4652b8e4f3ff #0
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 10/09/2023
RIP: 0010:ptp_ioctl+0xcb7/0x1d10 drivers/ptp/ptp_chardev.c:476
...
Call Trace:
<TASK>
posix_clock_ioctl+0xf8/0x160 kernel/time/posix-clock.c:86
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl fs/ioctl.c:857 [inline]
__x64_sys_ioctl+0x18f/0x210 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
```
This patch fixes the issue by adding a check for tsevq and
ensuring ptp_ioctl returns with an error if tsevq is null.
Reported-by: syzbot+8a78ecea7ac1a2ea26e5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=8a78ecea7ac1a2ea26e5
Fixes: c5a445b1e9 ("ptp: support event queue reader channel masks")
Signed-off-by: Yuran Pereira <yuran.pereira@hotmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no lock protection when writing ptp->tsevqs in ptp_open() and
ptp_release(), which can cause data corruption, use spin lock to avoid this
issue.
Moreover, ptp_release() should not be used to release the queue in ptp_read(),
and it should be deleted altogether.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reported-and-tested-by: syzbot+df3f3ef31f60781fa911@syzkaller.appspotmail.com
Fixes: 8f5de6fb24 ("ptp: support multiple timestamp event readers")
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Link: https://lore.kernel.org/r/tencent_CD19564FFE8DA8A5918DFE92325D92DD8107@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ida_alloc_max() function can return up to INT_MAX so this buffer is
not large enough. Also use snprintf() for extra safety.
Fixes: 403376ddb4 ("ptp: add debugfs interface to see applied channel masks")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/d4b1a995-a0cb-4125-aa1d-5fd5044aba1d@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use debugfs to be able to view channel mask applied to every timestamp
event queue.
Every time the device is opened, a new entry is created in
`$DEBUGFS_MOUNTPOINT/ptpN/$INSTANCE_ADDRESS/mask`.
The mask value can be viewed grouped in 32bit decimal values using cat,
or converted to hexadecimal with the included `ptpchmaskfmt.sh` script.
32 bit values are listed from least significant to most significant.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On systems with multiple timestamp event channels, some readers might
want to receive only a subset of those channels.
Add the necessary modifications to support timestamp event channel
filtering, including two IOCTL operations:
- Clear all channels
- Enable one channel
The mask modification operations will be applied exclusively on the
event queue assigned to the file descriptor used on the IOCTL operation,
so the typical procedure to have a reader receiving only a subset of the
enabled channels would be:
- Open device file
- ioctl: clear all channels
- ioctl: enable one channel
- start reading
Calling the enable one channel ioctl more than once will result in
multiple enabled channels.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use linked lists to create one event queue per open file. This enables
simultaneous readers for timestamp event queues.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce linked lists to access the timestamp event queue.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary structure to support custom private-data per
posix-clock user.
The previous implementation of posix-clock assumed all file open
instances need access to the same clock structure on private_data.
The need for individual data structures per file open instance has been
identified when developing support for multiple timestamp event queue
users for ptp_clock.
Signed-off-by: Xabier Marquiegui <reibax@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wincompatible-function-pointer-types-strict, a
warning designed to catch potential kCFI failures at build time rather
than run time due to incorrect function pointer types, there is a
warning due to a mismatch between the type of the mode parameter in
ptp_ocp_dpll_mode_get() vs. what the function pointer prototype for
->mode_get() in 'struct dpll_device_ops' expects.
drivers/ptp/ptp_ocp.c:4353:14: error: incompatible function pointer types initializing 'int (*)(const struct dpll_device *, void *, enum dpll_mode *, struct netlink_ext_ack *)' with an expression of type 'int (const struct dpll_device *, void *, u32 *, struct netlink_ext_ack *)' (aka 'int (const struct dpll_device *, void *, unsigned int *, struct netlink_ext_ack *)') [-Werror,-Wincompatible-function-pointer-types-strict]
4353 | .mode_get = ptp_ocp_dpll_mode_get,
| ^~~~~~~~~~~~~~~~~~~~~
1 error generated.
Change the type of the mode parameter in ptp_ocp_dpll_mode_get() to
clear up the warning and avoid kCFI failures at run time.
Fixes: 09eeb3aecc ("ptp_ocp: implement DPLL ops")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231002-net-wifpts-dpll_mode_get-v1-1-a356a16413cf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a copy and paste error so this uses a valid pointer instead of
an error pointer.
Fixes: 09eeb3aecc ("ptp_ocp: implement DPLL ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/5c581336-0641-48bd-88f7-51984c3b1f79@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.
Fixes: 773bda9649 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement basic DPLL operations in ptp_ocp driver as the
simplest example of using new subsystem.
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several cases where virtual net devices may benefit from
having a PTP clock, and these have to do with testing. I can see at
least netdevsim and veth as potential users of a common mock-up PTP
hardware clock driver.
The proposed idea is to create an object which emulates PTP clock
operations on top of the unadjustable CLOCK_MONOTONIC_RAW plus a
software-controlled time domain via a timecounter/cyclecounter and then
link that PHC to the netdevsim device.
The driver is fully functional for its intended purpose, and it
successfully passes the PTP selftests.
$ cd tools/testing/selftests/ptp/
$ ./phc.sh /dev/ptp2
TEST: settime [ OK ]
TEST: adjtime [ OK ]
TEST: adjfreq [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230807193324.4128292-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230714174922.4063153-1-robh@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The .adjphase operation is an operation that is implemented only by certain
PHCs. The sysfs device attribute node for querying the maximum phase
adjustment supported should not be exposed on devices that do not support
.adjphase.
Fixes: c3b60ab7a4 ("ptp: Add .getmaxphase callback to ptp_clock_info")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/netdev/20230627162146.GA114473@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/all/CA+G9fYtKCZeAUTtwe69iK8Xcz1mOKQzwcy49wd+imZrfj6ifXA@mail.gmail.com/
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Message-ID: <20230627232139.213130-1-rrameshbabu@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function that advertises a maximum offset of zero supported by
ptp_clock_info .adjphase in the OCP null ptp implementation.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT devices.
Refactor the negation of the offset stored in the register to be after the
boundary check of the offset value rather than before. Boundary check based
on the intended value rather than its device-specific representation.
Depend on ptp_clock_adjtime for handling out-of-range offsets.
ptp_clock_adjtime returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Min Li <min.li.xe@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT ClockMatrix devices. Depend on
ptp_clock_adjtime for handling out-of-range offsets. ptp_clock_adjtime
returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables advertisement of the maximum offset supported by the phase control
functionality of PHCs. The callback is used to return an error if an offset
not supported by the PHC is used in ADJ_OFFSET. The ioctls
PTP_CLOCK_GETCAPS and PTP_CLOCK_GETCAPS2 now advertise the maximum offset a
PHC's phase control functionality is capable of supporting. Introduce new
sysfs node, max_phase_adjustment.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIPS Boston board, which is using MIPS_GENERIC kernel is using
EG20T PCH and thus need this driver.
Dependency of PCH_GBE, PTP_1588_CLOCK_PCH is also fixed for
MIPS_GENERIC.
Note that CONFIG_PCH_GBE is selected in arch/mips/configs/generic/
board-boston.config for a while, some how it's never wired up
in Kconfig.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230607055953.34110-1-jiaxun.yang@flygoat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding a DFL (Device Feature List) device driver of ToD device for
Intel FPGA cards.
The Intel FPGA Time of Day(ToD) IP within the FPGA DFL bus is exposed
as PTP Hardware clock(PHC) device to the Linux PTP stack to synchronize
the system clock to its ToD information using phc2sys utility of the
Linux PTP stack. The DFL is a hardware List within FPGA, which defines
a linked list of feature headers within the device MMIO space to provide
an extensible way of adding subdevice features.
Signed-off-by: Raghavendra Khadatare <raghavendrax.anand.khadatare@intel.com>
Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230328142455.481146-1-tianfei.zhang@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba40 ("ptp_qoriq: fix NULL access if ptp dt node missing")
Signed-off-by: SongJingyi <u201912584@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KVM_HC_CLOCK_PAIRING currently fails inside SEV-SNP guests because the
guest passes an address to static data to the host. In confidential
computing the host can't access arbitrary guest memory so handling the
hypercall runs into an "rmpfault". To make the hypercall work, the guest
needs to explicitly mark the memory as decrypted. Do that in
kvm_arch_ptp_init(), but retain the previous behavior for
non-confidential guests to save us from having to allocate memory.
Add a new arch-specific function (kvm_arch_ptp_exit()) to free the
allocation and mark the memory as encrypted again.
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/r/20230308150531.477741-1-jpiotrowski@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/ptp/ptp_ines.c:783:34: error: ‘ines_ptp_ctrl_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230312132637.352755-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
