Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.
Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:
mv_set_main_irq_mask(host, ~0, 0);
The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.
The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.
However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause. This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports. With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned. It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset. SWNCQ is
modified to inherit from this new type.
This fixes hotplug regression reported in kernel bz#12351.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
nv_nf2_hardreset() will be used by other flavors too. Rename it to
nv_noclassify_hardreset().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port enabledness test fits much better into init_one() instead of
pre_reset(). The reason why these tests are in pre_reset() is purely
historical at this point. Move it to init_one(). This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The UDMA affliction is apparently specific to revision 0x11. Keeps us in sync
with drivers/ide current.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (94 commits)
ACPICA: hide private headers
ACPICA: create acpica/ directory
ACPI: fix build warning
ACPI : Use RSDT instead of XSDT by adding boot option of "acpi=rsdt"
ACPI: Avoid array address overflow when _CST MWAIT hint bits are set
fujitsu-laptop: Simplify SBLL/SBL2 backlight handling
fujitsu-laptop: Add BL power, LED control and radio state information
ACPICA: delete utcache.c
ACPICA: delete acdisasm.h
ACPICA: Update version to 20081204.
ACPICA: FADT: Update error msgs for consistency
ACPICA: FADT: set acpi_gbl_use_default_register_widths to TRUE by default
ACPICA: FADT parsing changes and fixes
ACPICA: Add ACPI_MUTEX_TYPE configuration option
ACPICA: Fixes for various ACPI data tables
ACPICA: Restructure includes into public/private
ACPI: remove private acpica headers from driver files
ACPI: reboot.c: use new acpi_reset interface
ACPICA: New: acpi_reset interface - write to reset register
ACPICA: Move all public H/W interfaces to new hwxface
...
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE()
so that libata doesn't spam the machine even when one of those
conditions triggers repeatedly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604cd is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reimplement mode programming logic of pata_hpt366 such that it's
identical to that of IDE hpt366 driver. The differences were...
* pata_hpt366 used 0xCFFF8FFFF to mask pio modes and 0x3FFFFFFF dma
modes. IDE hpt366 uses 0xC1F8FFFF for PIO, 0x303800FF for MWDMA and
0x30070000 for UDMA.
* pata_hpt366 doesn't set 0x08000000 for PIO unless it's already set
and always turns it on for MWDMA/UDMA. IDE hpt366 doesn't bother
with the bit. It always uses what was there.
* IDE hpt366 always clears 0xC0000000. pata_hpt366 doesn't.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to the Compact Flash specification r4.1, PIO modes 5 and 6
do not use iordy.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
--
UPD include/linux/compile.h
`___pata_platform_remove' referenced in section `__ksymtab_gpl' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
make: *** [.tmp_vmlinux1] Error 1
--
__pata_platform_remove() should not be in discarded section
__pata_platform_remove(struct device *dev) is invoked in both
pata_platform.c and pata_of_platform.c by reomve function defined in
discarded section ".devexit.text". An exported function should not be put
into discarded section.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AFAICT, struct sil24_port_multiplier isn't used anywhere. Remove it.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The present AHCI driver seems to support SATA GEN 3 speed, but the related
messages should be modified.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Certain ACPI implementations mess up IOCFG on _STM making libata
detect cable type incorrectly after a suspend/resume cycle. This
patch makes ata_piix save IOCFG on attach, use the saved value for
things which aren't dynamic and restore it on detach so that the next
driver also gets the BIOS initialized value.
This patch contains the following changes.
* makes ich_pata_cable_detect() use saved_iocfg.
* make piix_iocfg_bit18_quirk() take @host and use saved_iocfg.
* hpriv allocation moved upwards to save iocfg before doing anything
else.
This fixes bz#11879. Andreas Mohr reported and diagnosed the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In very obscure cases this can cause problems. We need to help the hardware
out a bit to avoid DMA problems on a reset.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct the DMA bit flags (UDMA and MWDMA were swapped)
Add workarounds so that we clear ERR and INTR bits before issuing a DMA
Add workarounds so that we stop a live DMA before touching the CTL register
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As suggested by Linus: Don't do the libata init in 2 separate
steps with a global sync inbetween, but do it as one async step,
with a local sync before registering the device.
This cuts the boottime on my machine with 2 sata controllers down
significantly, and it seems to work. Would be nice if the libata
folks take a good look at this patch though..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch makes the libata port scanning asynchronous (per device).
There is a synchronization point before doing the actual disk scan
so that device ordering is not affected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This implements support for the Large Block Transfer feature found in Silicon
Image 311x controllers. This allows transferring bigger contiguous chunks of
data from system memory and avoids the 64KB boundary restriction of standard
SFF controllers.
This is based on a patch from Jeff Garzik (from the sii-lbt branch of
libata-dev) but includes a few bug fixes: Since the bmdma2 register does not
implement the status bits, the original bmdma register must be used except
where the bmdma2 register is required. As well the DMA boundary should be
31-bit instead of 32-bit since the top bit of the length field is still
required for the PRD end-of-table flag.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit
ATA: piix, fix pointer deref on suspend
fixed a possible oops in an ugly manner. Use newly introduced dmi_match()
to make the code pretty again.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patchlet below blacklists NCQ on OCZ CORE v2 SSD drive(s). Even
though the drive advertises NCQ support with queue depth 1, it responds
with all-zeroes FIS to NCQ commands which triggers ata error handling
several times before the kernel decides to disable NCQ on the drive.
Signed-off-by: Lubomir Bulej <lubomir.bulej@dsrg.mff.cuni.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself. However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.
This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When restoring SControl during detach, PMP links should be handled
first as changing SControl of the host link can affect SCR access of
PMP links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform. Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.
With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
IDE hpt366 driver doesn't allow DMA for ATAPI devices and MWDMA2 on
ATAPI device locks up pata_hpt366. Follow the suit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 is strange in that its two channels occupy two PCI
functions and both are primary channels and bit1 of PCI configuration
register 0x5A indicates cable for both channels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to miscommunication, P/N was mistaken as firmware revision
strings. Update it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The hardware supports transfers up to a page boundary per buffer.
Currently, we work around that in the DMA code by splitting each
buffer up as we run through the scatterlist. Avoid this by telling
the block layers about the hardware restriction.
Eventually, this will allow us to phase out the splitting code,
but not until the old IDE layer allows us to control the value it
gives to blk_queue_segment_boundary().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the IOMD DMA code walks the scatterlist using sg_next,
converting the sg list into a contiguous list is no longer required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some systems report SIS 5513 as both vendor/id and subvendor/id
string. In that case we can't distinguish the system by the id
svid/sdid and in fact the entry here breaks some boxes. At some
point we need to find another way to detect the Targa Visionary 1000,
until then this trades a hang for some users with lower performance
for others.
Closes: #12092
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
I've found this issue in the mmotm 2008-12-02-17-08.
--
Commit
ata_piix: add borked Tecra M4 to broken suspend list
introduced DMI variables checking, but they can be null, so that
we possibly dereference null.
Check if they are null and avoid checks in that case.
Solves:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff8043da97>] piix_pci_device_suspend+0x117/0x230
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 had its clock detection wrong and detected 25Mhz as 40Mhz
and vice-versa. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ehc->last_reset is used to ensure that resets are not issued too
close to each other. It's initialized to jiffies minus one minute
on EH entry. However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.
This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized. As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.
This problem is spotted and debugged by Shane Huang.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same
sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid
overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to
exist in ata_tf_read_block(). Fix this by adding a cast to u64.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I posted this last month, but was prompted to do so again in bz#467457
Add capability flag to support slave devices with pata_sch driver.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect(). Remove them.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reverts the following three commits which convert libata to
use block layer tagging.
43a49cbdf3e013e13bf62fca5ccf97
Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.
The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands. Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made. I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.
So, for the time being, keep using the old dumb in-libata qc
allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling. Mask off DET when restoring
SControl.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All three flavors of sata_nv's are different in how their hardreset
behaves.
* generic: Hardreset is not reliable. Link often doesn't come online
after hardreset.
* nf2/3: A little bit better - link comes online with longer debounce
timing. However, nf2/3 can't reliable wait for the first D2H
Register FIS, so it can't wait for device readiness or classify the
device after hardreset. Follow-up SRST required.
* ck804: Hardreset finally works.
The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors. This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it
catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.
The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.
To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
5287 used to be treated as vt6420 but it didn't work. It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports. This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata. Another controller
which falls into this category is ata_piix w/ SIDPR access.
libata now has facility to deal with this class of controllers named
slave_link. A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.
This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.
This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In ata_tf_to_lba48(), when evaluating
(tf->hob_lbal & 0xff) << 24
the expression is promoted to signed int (since int can hold all values
of u8). However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.
For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:
ata3.00: HPA detected: current 2930277168, native 18446744072344861488
where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.
Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.
Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove excess kernel-doc function parameter notation from drivers/ata/:
Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: ahci enclosure management bit mask
libata: ahci enclosure management led sync
pata_ninja32: suspend/resume support
libata: Fix LBA48 on pata_it821x RAID volumes.
libata: clear saved xfer_mode and ncq_enabled on device detach
sata_sil24: configure max read request size to 4k
libata: add missing kernel-doc
libata: fix device iteration bugs
ahci: Add support for Promise PDC42819
ata: Switch all my stuff to a common address
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed. These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems. However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported. This optimization
is also done by SIMG's windows driver.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata missing kernel-doc:
Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.
* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()
While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.
This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.
Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.
Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices
The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list. So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
VIA controllers clear DEVICE register when IEN changes. Make sure
DEVICE is updated along with CTL.
This change is separated from Joseph Chan's larger patch.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links. This patch clears device class to NONE
during post-reset processing if phys link is offline.
As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link. ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer. This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.
Don't set ATA_PFLAG_RECOVERED for slave link actions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH. As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.
This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning. Make sure it's initialized.
Reported by Larry Finger.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
doc/cdrom: Trvial documentation error, file not present
block_dev: fix kernel-doc in new functions
block: add some comments around the bio read-write flags
block: mark bio_split_pool static
block: Find bio sector offset given idx and offset
block: gendisk integrity wrapper
block: Switch blk_integrity_compare from bdev to gendisk
block: Fix double put in blk_integrity_unregister
block: Introduce integrity data ownership flag
block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
bio.h: Remove unused conditional code
block: remove end_{queued|dequeued}_request()
block: change elevator to use __blk_end_request()
gdrom: change to use __blk_end_request()
memstick: change to use __blk_end_request()
virtio_blk: change to use __blk_end_request()
blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
block: add lld busy state exporting interface
block: Fix blk_start_queueing() to not kick a stopped queue
include blktrace_api.h in headers_install
...
* 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
libata-eh: clear UNIT ATTENTION after reset
ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
libata: reorder ata_device to remove 8 bytes of padding on 64 bits
[libata] pata_bf54x: Add proper PM operation
pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
libata: Implement disk shock protection support
[libata] Introduce ata_id_has_unload()
PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
ata_piix: drop merged SCR access and use slave_link instead
libata: implement slave_link
libata: misc updates to prepare for slave link
libata: reimplement link iterator
libata: make SCR access ops per-link
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:
1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
is unsigned type, the check will be true for `-1'.
Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command. As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users. For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.
Clearing UA has some problems as it might clear UA which the userland
needs to know about. However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons. Missing UA
can only delay failure to one of the following commands anyway. For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run. Although
the userland application won't get the UA, its pending writes will
fail.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[akpm@linux-foundation.org: remove ifdefs, make things static]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The RPC machine type now selects HAVE_PATA_PLATFORM so we can remove
the special case in the PATA_PLATFORM configuration code.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata has slave_link, there's no need to keep ugly merged
SCR access. Drop it and use slave_link instead. This results in
simpler code and much better separate link handling for master and
slave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Explanation taken from the comment of ata_slave_link_init().
In libata, a port contains links and a link contains devices. There
is single host link but if a PMP is attached to it, there can be
multiple fan-out links. On SATA, there's usually a single device
connected to a link but PATA and SATA controllers emulating TF based
interface can have two - master and slave.
However, there are a few controllers which don't fit into this
abstraction too well - SATA controllers which emulate TF interface
with both master and slave devices but also have separate SCR
register sets for each device. These controllers need separate links
for physical link handling (e.g. onlineness, link speed) but should
be treated like a traditional M/S controller for everything else
(e.g. command issue, softreset).
slave_link is libata's way of handling this class of controllers
without impacting core layer too much. For anything other than
physical link handling, the default host link is used for both master
and slave. For physical link handling, separate @ap->slave_link is
used. All dirty details are implemented inside libata core layer.
From LLD's POV, the only difference is that prereset, hardreset and
postreset are called once more for the slave link, so the reset
sequence looks like the following.
prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
softreset(M) -> postreset(M) -> postreset(S)
Note that softreset is called only for the master. Softreset resets
both M/S by definition, so SRST on master should handle both (the
standard method will work just fine).
As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.
* ata_is_host_link() updated so that slave_link is considered as host
link too.
* iterator extended to iterate over the slave_link when using the
underbarred version.
* force param handling updated such that devno 16 is mapped to the
slave link/device.
* ata_link_on/offline() updated to return the combined result from
master and slave link. ata_phys_link_on/offline() are the direct
versions.
* EH autopsy and report are performed separately for master slave
links. Reset is udpated to implement the above described reset
sequence.
Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.
After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 2fd673ecf0 which tried to remove
hardreset for generic accidentally removed it for all flavors as all
others were inheriting from nv_generic_ops. This patch reinstates
nv_hardreset() and puts it into nv_common_ops which all flavors
inherit from. nv_generic_ops now inherits from nv_common_ops and
overrides .hardreset to ATA_OP_NULL.
While at it, explain why nv_hardreset and ATA_OP_NULL override are
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
dock driver can handle ata(bay) hotplug now. dock driver already handles
_EJ0 and _STA, so remove them. Also libata doesn't need register
notification handler anymore.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enable LED blinking.
Signed-off-by: Bob Stewart <bob@evoria.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/ata_piix.c:1502:7: warning: symbol 'rc' shadows an earlier one
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove duplicate call to pcim_enable_device in sil680_init_one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it. Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.
OSDL bz#11065 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.
OSDL bug 11195 reports that sata_nv generic flavor falls into this
category. Hardreset itself succeeds but PHY stays offline after
hardreset. I tried longer debounce timing but the result was the
same.
http://bugzilla.kernel.org/show_bug.cgi?id=11195
So, it seems we'll have to drop hardreset from the generic flavor.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell ahcis don't play nicely with PMPs. Disable it.
Reported by KueiHuan Chen in the following thread.
http://thread.gmane.org/gmane.linux.ide/33296
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: KueiHuan Chen <kueihuan.chen@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I've been chasing Jeff about this for months. Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.
This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!
This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.
To quote Jeff in email
> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.
> See? It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."
(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)
To quote Jeff in August 2007
> " mv-ahci-pata
> Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."
Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.
The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While doing some easy cleanups on the sparc code I noticed that the
CONFIG_SUN4 code seems to be worse than the rest - there were some
"I don't know how it should work, but the current code definitely cannot
work." places.
And while I have seen people running Linux on machines like a
SPARCstation 5 a few years ago I don't recall having seen sun4
machines, even less ones running Linux.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pcmcia-config-loop:
pcmcia: pcmcia_config_loop() improvement by passing vcc
pcmcia: pcmcia_config_loop() default CIS entry handling
pcmcia: pcmcia_config_loop() ConfigIndex unification
pcmcia: use pcmcia_loop_config in misc pcmcia drivers
pcmcia: use pcmcia_loop_config in net pcmcia drivers
pcmcia: use pcmcia_loop_config in ISDN pcmcia drivers
pcmcia: use pcmcia_loop_config in scsi pcmcia drivers
pcmcia: use pcmcia_loop_config in bluetooth drivers
pcmcia: use pcmcia_loop_config in pata and ide drivers
pcmcia: add pcmcia_loop_config() helper
* pcmcia-printk:
pcmcia: don't add extra DEBUG cflag
pcmcia: remove unused cs_socket_name() definition
pcmcia: use dev_printk in module rsrc_nonstatic
pcmcia: use dev_printk in module pcmcia
pcmcia: use dev_printk in module pcmcia_core
pcmcia: use dev_printk and dev_dbg in yenta_socket
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in pata_pcmcia and ide_cs
CC: Tejun Heo <htejun@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Over time, a few differences have accumulated between pata_pcmcia
and ide-cs. Fix those.
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function
Pretty horrid fix, but so's a warning..
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15. However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first. Interestingly, the SRST itself
succeeds but the following commands fail.
If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.
Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit bfce5e0179 implemented custom
tf_load for pata_via. This patch cleans it up a bit.
* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
when necessary.
* Rename via_ata_tf_load() to via_tf_load().
* No need to set .tf_load in via_port_ops_noirq as it inherits from
via_port_ops.
* Clean up indentation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SError belongs to link not port. Use ata_link_printk() to print it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN. However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN. This
makes reset paths more predictable and thus less error-prone.
While at it, move hardreset error checking such that it's done right
after hardreset is finished. This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset(). The original intention was to clear reset action
which wasn't selected. This can cause unexpected behavior when other
EH actions are scheduled together with reset. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Resend with proper whitespace.
This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv allowed issuing two DMA commands concurrently which the
hardware allows. Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
relevant bits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Subsys 106b:00a3 also is the weird apple ich8m which chokes when the
latter two ports are accessed, add it. Reported by Felipe Sere.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Felipe Sere <dodofxp@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a potential memory leak when ata_init() encounters an error.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Global and per-LLD ATAPI disable checks were done in the command issue
path probably because it was left out during EH conversion. On
affected machines, this can cause lots of warning messages. Move them
to where they belong - the probing path.
Reported by Chunbo Luo.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add flag VIA_SATA_PATA for vx800, VX800 uses the same
chipset(0x0581/0x5324) as CX700, which has 1 PATA channel(Master/Slave)
and 1 SATA channel(Master/Slave) Add function <via_ata_tf_load>. This is
to fix the internal bug of VIA chipsets, which will reset the device
register after changing the IEN bit in CTL register
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ali_init_one() function does a search for an isa_bridge,
but then fails to release it if the revision information was
not correctly found.
the problem comes from:
isa_bridge = pci_get_device(...);
if (isa_bridge && ...) {
pci_dev_put(isa_bridge);
}
where the pci_dev_put() is never called if isa_bridge
was valid but the extra checks on the chip-revision
fail to match.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new type checking of the flags arguments to irqsave and friends
(commit 3f307891ce) pointed out this thing
with a big nice warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
AHCI: Remove an unnecessary flush from ahci_qc_issue
AHCI: speed up resume
[libata] Add support for VPD page b1
ata: endianness annotations in pata drivers
libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
[libata] sata_svw: update code comments relating to data corruption
libata/ahci: enclosure management support
libata: improve EH internal command timeout handling
libata: use ULONG_MAX to terminate reset timeout table
libata: improve EH retry delay handling
libata: consistently use msecs for time durations
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
splice: fix generic_file_splice_read() race with page invalidation
ramfs: enable splice write
drivers/block/pktcdvd.c: avoid useless memset
cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
scsi: sr avoids useless buffer allocation
block: blk_rq_map_kern uses the bounce buffers for stack buffers
block: add blk_queue_update_dma_pad
DAC960: push down BKL
pktcdvd: push BKL down into driver
paride: push ioctl down into driver
block: use get_unaligned_* helpers
block: extend queue_flag bitops
block: request_module(): use format string
Add bvec_merge_data to handle stacked devices and ->merge_bvec()
block: integrity flags can't use bit ops on unsigned short
cmdfilter: extend default read filter
sg: fix odd style (extra parenthesis) introduced by cmd filter patch
block: add bounce support to blk_rq_map_user_iov
cfq-iosched: get rid of enable_idle being unused warning
allow userspace to modify scsi command filter on per device basis
...
In an I/O heavy workload (IOZone), ahci_qc_issue is the second-highest
consumer of CPU cycles. Removing the flush gets us approximately 10%
bandwidth improvement. I believe this to be because the CPU can start
queueing the next request instead of waiting for the readl() to flush the
writes to the device. The flush isn't necessary because we're using a
'queue' metaphor; we don't guarantee the command has got to the device,
nor do we need to guarantee the command has got to the controller.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During resume, sleep 1 second to wait for the HBA reset
to finish is a waste of time.
According to the AHCI 1.2 spec,
We should poll the HOST_CTL register,
and return error if the host reset is not
finished within 1 second.
Test results show that the HBA reset can be done quickly(in usecs).
And this patch may save nearly 1 second during resume.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SCSI VPD page b1 reports the nominal rotation speed and physical size
of the device. Devices that conform to ATA-8 can return this information
in words 217 and 168 of the identify data.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_qdi.c:142:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_qdi.c:142:9: expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_qdi.c:142:9: got restricted __le32 [usertype] <noident>
drivers/ata/pata_qdi.c:146:15: warning: cast to restricted __le32
drivers/ata/pata_winbond.c:110:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_winbond.c:110:9: expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_winbond.c:110:9: got restricted __le32 [usertype] <noident>
drivers/ata/pata_winbond.c:114:15: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:310:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:310:9: expected unsigned int [unsigned] [usertype] pad
drivers/ata/pata_legacy.c:310:9: got restricted __le32 [usertype] <noident>
drivers/ata/pata_legacy.c:314:15: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:752:11: warning: cast to restricted __le32
drivers/ata/pata_legacy.c:756:9: warning: incorrect type in assignment (different base types)
drivers/ata/pata_legacy.c:756:9: expected unsigned int [unsigned] [addressable] [assigned] [usertype] pad
drivers/ata/pata_legacy.c:756:9: got restricted __le32 [usertype] <noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update atapi_eh_request_sense() to take @dev, @sense_buf and
@dfl_sense_key instead of taking @qc and extracting information from
it. This change is to make the function more generic and allow it to
be called from other places.
While at it, make cdb initialization use initializer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Enclosure Management support to libata and ahci.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong. This patch
implements command type based stepped timeouts. Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.
ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much. After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.
IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.
This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This doesn't introduce any functional changes. This is to make reset
timeout table consistent with to-be-added command timeout tables.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back. However, this 5 second delay is superflous or excessive
in many cases. For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.
This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.
As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.
While at it, convert explicit rounding up division to DIV_ROUND_UP().
This change speeds up EH in many cases w/o sacrificing robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing. As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs. So, durations are in msecs and
deadlines are in jiffies. ata_deadline() is added to compute deadline
from a start time and duration in msecs.
While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The problem is introduced by commit
664d080c41.
acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration. This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled. On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.
This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read. This patch makes ahci driver
always use the unmasked value to clear irq_status.
While at it, add explanation on the peculiarities of ahci IRQ
clearing.
This was spotted by Linus Torvalds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a miniscule chance that two separate host controllers
might be in sata_mv at the same time and manage to decrement
the static limit_warnings variable below zero.
Fix the comparison to deal with it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm. Always clear full irq_stat instead of only the bits
that are handled. As nothing changes for recognized ports, the risk
of breaking things is pretty low.
Reported and verified by Philipp Thomas in the following suse
bugzilla.
https://bugzilla.novell.com/attachment.cgi?id=215692
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's another DID used for Adaptec card. Add it.
Reported by Travis Read.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Travis Read <ics@dark.net.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).
This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sata_uli can't do hardresets reliably and lock up. This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.
Reported by Christian Casteyde in bz#10860.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
BAST: Remove old IDE driver
pcmcia ide kingston compactflash's have a new manufacturer id
pcmcia: add another pata/ide ID
pcmcia: add an pata/ide ID
ide: increase timeout in wait_drive_not_busy()
palm_bk3710: fix resource management
Addition of Transcend 1GB 45x id so that it is properly detected.
[bart: fix typo in ide-cs's ID spotted by Alan Cox]
Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Piter PUNK <piterpunk@slackware.com>
SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used. Turn off PMP support.
tj: added patch description, adapted patch to #upstream-fixes and
renamed board_ahci_sis to board_ahci_nopmp.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
