This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Since commit cafa0010cd ("Raise the minimum required gcc version to
4.6"), this is the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Any spaces events received after a reset or startup should be discarded,
so ensure the rc device is in idle mode.
This also makes it much easier to detect incorrect raw events, as we will
do in a following commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of this enum doesn't match what it
actually represents. Adjust it.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c9 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible for lircd to read from a lirc chardev, and not
keep it busy.
Note that this changes the default for timeout reports to on. lircd
already enables timeout reports when it opens a lirc device, leaving
them on until the next reboot.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements LIRC_MODE_SCANCODE reading from the lirc device. The
scancode can be read from the input device too, but with this interface
you get the rc protocol, keycode, toggle and repeat status in addition
to just the scancode.
int main()
{
int fd, mode, rc;
fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_REC_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode;
while (read(fd, &scancode, sizeof(scancode)) == sizeof(scancode)) {
printf("protocol:%d scancode:0x%x toggle:%d repeat:%d\n",
scancode.rc_proto, scancode.scancode,
!!(scancode.flags & LIRC_SCANCODE_FLAG_TOGGLE),
!!(scancode.flags & LIRC_SCANCODE_FLAG_REPEAT));
}
close(fd);
}
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
rc-core has replaced the lirc kapi many years ago, and now with the last
driver ported to rc-core, we can finally remove it.
Note this has no effect on userspace.
All future IR drivers should use the rc-core api.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the generic kernel lirc api with ones which use rc-core, further
reducing the lirc_dev members.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is done to further remove the lirc kernel api. Ensure that every
fops checks for this.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the only mode lirc devices can handle is raw IR, handle this
in a plain kfifo.
Remove lirc_buffer since this is no longer needed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc user interface exists as a raw decoder, which does not make
much sense for transmit-only devices.
In addition, we want to have lirc char devices for devices which do not
use raw IR, i.e. scancode only devices.
Note that rc-code, lirc_dev, ir-lirc-codec are now calling functions of
each other, so they've been merged into one module rc-core to avoid
circular dependencies.
Since ir-lirc-codec no longer exists as separate codec module, there is no
need for RC_DRIVER_IR_RAW_TX type drivers to call ir_raw_event_register().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the lirc device supports it, set the carrier for the protocol.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.
Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.
Verified on a HVR-1150 and Raspberry Pi.
Fixes: 3f5c4c7332 ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The NEC scancode composing and protocol type detection in
ir_nec_decode() is generic enough to be a shared function. Let's create
an inline function in rc-core.h, so that other remote control drivers
can reuse this function to save some code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a4 ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
IR raw transmitter driver type is specified in the enum
rc_driver_type as RC_DRIVER_IR_RAW_TX which includes all those
devices that transmit raw stream of bit to a receiver.
The data are provided by userspace applications, therefore they
don't need any input device allocation, but still they need to be
registered as raw devices.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true and
rc_dev::allowed_wakeup_protocols should be set to the raw IR encoders.
We also do not permit the mask to be set as we cannot generate IR
which would match that.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode to a form that is more suitable for raw
hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For IR wakeup, a driver has to program the hardware to wakeup at a
specific IR sequence, so it makes no sense to allow multiple wakeup
protocols to be selected. In the same manner the sysfs interface only
allows one scancode to be provided.
In addition, we need to know the specific variant of the protocol.
In short, these changes are made to the wakeup_protocols sysfs entry:
- list all the protocol variants rather than the protocol groups,
e.g. "nec nec-x nec-32" rather than just "nec".
- only allow one protocol variant to be selected rather than multiple
- wakeup_filter can only be set once a protocol has been selected in
wakeup_protocols.
This is an API change, however the only user of this API is the img-ir,
but the wakeup code was never merged to mainline, so it was never used.
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Introduce managed versions of both functions.
They allows to simplify the error path in the probe function of
rc drivers, and usually also to simplify the remove function.
New element managed_alloc in struct rc_dev is needed to correctly
handle mixed use, e.g. managed version of rc_register_device and
normal version of rc_allocate_device.
In addition devm_rc_allocate_device sets rc->dev.parent as having a
reference to the parent device might be useful for future extensions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by linuxdoc[1] tool, using:
$ for i in $(git grep kernel-doc Documentation/media/kapi/|cut -d: -f4); do kernel-lintdoc --sloppy $i; done
include/media/v4l2-dev.h:118 :WARN: function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-mc.h:56 [kernel-doc WARN] : enum name from comment differs: if_vid_dec_index <--> if_vid_dec_pad_index
include/media/v4l2-mc.h:71 [kernel-doc WARN] : enum name from comment differs: if_aud_dec_index <--> if_aud_dec_pad_index
include/media/v4l2-mem2mem.h:396 [kernel-doc WARN] : function name from comment differs: v4l2_m2m_num_src_bufs_ready <--> v4l2_m2m_num_dst_bufs_ready
drivers/media/dvb-core/dvb_math.h:28 [kernel-doc WARN] : function name from comment differs: cintlog2 <--> intlog2
include/media/v4l2-subdev.h:215 [kernel-doc WARN] : struct name from comment differs: s_radio <--> v4l2_subdev_tuner_ops
include/media/v4l2-subdev.h:890 [kernel-doc WARN] : function name from comment differs: v4l2_set_subdevdata <--> v4l2_set_subdev_hostdata
include/media/v4l2-subdev.h:901 [kernel-doc WARN] : function name from comment differs: v4l2_get_subdevdata <--> v4l2_get_subdev_hostdata
drivers/media/dvb-core/dvb_ringbuffer.h:196 [kernel-doc WARN] : function name from comment differs: dvb_ringbuffer_writeuser <--> dvb_ringbuffer_write_user
include/media/videobuf2-core.h:399 [kernel-doc WARN] : struct name from comment differs: vb2_ops <--> vb2_buf_ops
include/media/media-entity.h:132 [kernel-doc ERROR] : duplicate parameter definition 'source'
include/media/media-entity.h:477 [kernel-doc WARN] : function name from comment differs: media_entity_enum_test <--> media_entity_enum_test_and_set
include/media/media-entity.h:535 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_pad
include/media/media-entity.h:544 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_link
include/media/media-entity.h:553 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_intf
include/media/media-entity.h:562 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> intf_to_devnode
include/media/rc-core.h:234 [kernel-doc WARN] : function name from comment differs: rc_open <--> rc_close
include/media/v4l2-ctrls.h:397 [kernel-doc WARN] : missing initial short description of 'v4l2_ctrl_handler_init'
include/media/v4l2-dev.h:118 [kernel-doc WARN] : function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-event.h:225 [kernel-doc WARN] : missing initial short description of 'v4l2_src_change_event_subscribe'
[1] https://return42.github.io/linuxdoc/linux.html
The above are real issues at the documentation. On several cases,
caused by cut-and-paste.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* patchwork: (1492 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc script is now broken if it doesn't find all
exported symbols documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of hardcoding a timeout, let userspace change it dynamically
by adding a s_timeout ops.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
struct ir_raw_event currently has a size of 12 bytes on most (all?)
architectures. This can be reduced to 8 bytes whilst maintaining
full backwards compatibility.
This saves 2KB in size of struct ir_raw_event_ctrl (as element
kfifo is reduced by 512 * 4 bytes) and it allows to copy the
full struct ir_raw_event with a single 64 bit operation.
Successfully tested with the Nuvoton driver and successfully
compile-tested with the ene_ir driver (as it uses the carrier /
duty_cycle elements).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device initialization completes only after calling
input_register_device(). However, rc_open() can be called while
the device is being registered by the input/evdev core. So, we
can't expect that rc_dev->initialized to be true.
Change the logic to don't require initialized == true at rc_open
and change the type of initialized to be atomic.
this way, we can check for it earlier where it is really needed,
without needing to lock the mutex just for testing it.
Tested with nuvoton_cir driver on a NUC5i7RYB with CIR integrated on it.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex lock at rc_register_device() was added by commit 08aeb7c9a4
("[media] rc: add locking to fix register/show race").
It is meant to avoid race issues when trying to open a sysfs file while
the RC register didn't complete.
Adding a lock there causes troubles, as detected by the Kernel lock
debug instrumentation at the Kernel:
======================================================
[ INFO: possible circular locking dependency detected ]
4.5.0-rc3+ #46 Not tainted
-------------------------------------------------------
systemd-udevd/2681 is trying to acquire lock:
(s_active#171){++++.+}, at: [<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
but task is already holding lock:
(&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->lock){+.+.+.}:
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff822de966>] mutex_lock_nested+0xb6/0x860
[<ffffffffa0721f2b>] show_protocols+0x3b/0x3f0 [rc_core]
[<ffffffff81cdaba5>] dev_attr_show+0x45/0xc0
[<ffffffff8171f1b3>] sysfs_kf_seq_show+0x203/0x3c0
[<ffffffff8171a6a1>] kernfs_seq_show+0x121/0x1b0
[<ffffffff81617c71>] seq_read+0x2f1/0x1160
[<ffffffff8171c911>] kernfs_fop_read+0x321/0x460
[<ffffffff815abc20>] __vfs_read+0xe0/0x3d0
[<ffffffff815ae90e>] vfs_read+0xde/0x2d0
[<ffffffff815b1d01>] SyS_read+0x111/0x230
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
-> #0 (s_active#171){++++.+}:
[<ffffffff81244f24>] __lock_acquire+0x4304/0x5990
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff81717d3a>] __kernfs_remove+0x58a/0x810
[<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
[<ffffffff81721592>] remove_files.isra.0+0x72/0x190
[<ffffffff8172174b>] sysfs_remove_group+0x9b/0x150
[<ffffffff81721854>] sysfs_remove_groups+0x54/0xa0
[<ffffffff81cd97d0>] device_remove_attrs+0xb0/0x140
[<ffffffff81cdb27c>] device_del+0x38c/0x6b0
[<ffffffffa0724b8b>] rc_register_device+0x8cb/0x1450 [rc_core]
[<ffffffffa1326a7b>] dvb_usb_remote_init+0x66b/0x14d0 [dvb_usb]
[<ffffffffa1321c81>] dvb_usb_device_init+0xf21/0x1860 [dvb_usb]
[<ffffffffa13517dc>] dib0700_probe+0x14c/0x410 [dvb_usb_dib0700]
[<ffffffff81dbb1dd>] usb_probe_interface+0x45d/0x940
[<ffffffff81ce7e7a>] driver_probe_device+0x21a/0xc30
[<ffffffff81ce89b1>] __driver_attach+0x121/0x160
[<ffffffff81ce21bf>] bus_for_each_dev+0x11f/0x1a0
[<ffffffff81ce6cdd>] driver_attach+0x3d/0x50
[<ffffffff81ce5df9>] bus_add_driver+0x4c9/0x770
[<ffffffff81cea39c>] driver_register+0x18c/0x3b0
[<ffffffff81db6e98>] usb_register_driver+0x1f8/0x440
[<ffffffffa074001e>] dib0700_driver_init+0x1e/0x1000 [dvb_usb_dib0700]
[<ffffffff810021b1>] do_one_initcall+0x141/0x300
[<ffffffff8144d8eb>] do_init_module+0x1d0/0x5ad
[<ffffffff812f27b6>] load_module+0x6666/0x9ba0
[<ffffffff812f5fe8>] SyS_finit_module+0x108/0x130
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->lock);
lock(s_active#171);
lock(&dev->lock);
lock(s_active#171);
*** DEADLOCK ***
3 locks held by systemd-udevd/2681:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
In this specific case, some error happened during device init,
causing IR to be disabled.
Let's fix it by adding a var that will tell when the device is
initialized. Any calls before that will return a -EINVAL.
That should prevent the race issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A default timeout value of 125 ms should work for all decoders.
Declare a constant to help standardize its' use.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
Warning(.//include/media/rc-core.h:178): No description found for parameter 's_rx_carrier_range'
Warning(.//include/media/rc-core.h:178): Excess struct/union/enum/typedef member 's_rx_carrier' description in 'rc_dev'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes rc-core to use the kernel facilities that are already
available for handling unique numbers instead of rolling its own bitmap
stuff.
Signed-off-by: David Härdeman <david@hardeman.nu>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.
As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The hole point of IR_dprintk() is that, once a level is
given at debug parameter, all enabled IR parsers will show their
debug messages.
While converting it to dynamic_printk might be a good idea,
right now it just makes very hard to debug the drivers, as
one needs to both pass debug=1 or debug=2 to rc-core and
to use the dynamic printk to enable all the desired lines.
That doesn't make sense!
So, revert to the old way, as a single line is changed,
and the debug parameter will now work as expected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The generic scancode filtering has questionable value and makes it
impossible to determine from userspace if there is an actual
scancode hw filter present or not.
So revert the generic parts.
Based on a patch from James Hogan <james.hogan@imgtec.com>, but this
version also makes sure that only the valid sysfs files are created
in the first place.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Overloading dev->s_filter to do two different functions (set wakeup filters
and generic hardware filters) makes it impossible to tell what the
hardware actually supports, so create a separate dev->s_wakeup_filter and
make the distinction explicit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
