Simplify the way the return value is set a number of times (mostly on
error).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge list_del() + list_add_tail() to list_move_tail().
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit changed an internal radeon structure, that meant a new driver
in -next had to be fixed up, merge in the commit and fix up the driver.
Also fixes a trivial nouveau merge.
Conflicts:
drivers/gpu/drm/nouveau/nouveau_mem.c
Typo in the aspect scale setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
So we used to use lpfn directly to restrict VRAM when we couldn't
access the unmappable area, however this was removed in
93225b0d7b as it also restricted
the gtt placements. However it was only later noticed that this
broke on some hw.
This removes the active_vram_size, and just explicitly sets it
when it changes, TTM/drm_mm will always use the real_vram_size,
and the active vram size will change the TTM size used for lpfn
setting.
We should re-work the fpfn/lpfn to per-placement at some point
I suspect, but that is too late for this kernel.
Hopefully this addresses:
https://bugs.freedesktop.org/show_bug.cgi?id=35254
v2: fix reported useful VRAM size to userspace to be correct.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We've been getting reports of complete system lockups with rv3xx hw on
AGP and PCIE when running gnome-shell or kwin with compositing.
It appears the hw really doesn't like setting these registers while
stuff is running, this moves the setting of the registers into the modeset
since they aren't required to be changed anywhere else.
fixes: https://bugs.freedesktop.org/show_bug.cgi?id=35183
Reported-and-tested-by: Álmos <aaalmosss@gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like these got passed over with both being merged at the same
time but not quite meeting in the middle.
should fix: https://bugs.freedesktop.org/show_bug.cgi?id=34137
along with Michael's phoronix article.
Reported-by: Chi-Thanh Christopher Nguyen
Article-written-by: Michael Larabel @ phoronix
Signed-off-by: Dave Airlie <airlied@redhat.com>
hdmi 1.3 raises the max clock from 165 Mhz to 340 Mhz.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is different enough from evergreen to warrant it's own functions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman asics have 3 ring buffers:
ring 0 supports both gfx and compute
rings 1 and 2 are compute only
At the moment we only support ring 0.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch sets up the gart in legacy mode. We
probably want to switch to full VM mode at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is DCE5 display plus a new 4-way shader block.
3D state programming is similar to evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
have to read values from the IB in order as we could cross
a page boundary at any time and won't be able to go backwards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a bunch of off by one errors in the sanity checks here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 5a893fc28f.
This causes a use after free in the ttm free alloc pages path,
when it tries to get the be after the be has been destroyed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'stable/ttm.pci-api.v5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
ttm: Include the 'struct dev' when using the DMA API.
nouveau/ttm/PCIe: Use dma_addr if TTM has set it.
radeon/ttm/PCIe: Use dma_addr if TTM has set it.
ttm: Expand (*populate) to support an array of DMA addresses.
ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set.
ttm: Introduce a placeholder for DMA (bus) addresses.
the texture checking code didn't work for block formats like s3tc,
this overhauls it to work for all types.
v2: add texture array support.
v3: add subsampled formats
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now all the asic specific stuff ist mostly hid in radeon_asic.*
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
... and switch it to container_of upcasting.
v2: converted new pageflip code-paths.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unconditionally initialize the drm gem object - it's not
worth the trouble not to for the few kernel objects.
This patch only changes the place of the drm gem object,
access is still done via pointers.
v2: Uncoditionally align the size in radeon_bo_create. At
least the r600/evergreen blit code didn't to this, angering
the paranoid gem code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some userspaces can emit a whole packet without disabling AA resolve
by the looks of it, so we have to deal with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: Jorg Otte <jrg.otte@googlemail.com>
r100_gpu_init() was dropped in 90aca4d ("drm/radeon/kms: simplify &
improve GPU reset V2") but here it was only commented out.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this aligns the height of the fb allocation so it doesn't trip
over the size checks later when we use this from userspace to
copy the buffer at X start.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit a6f9761743.
Remove this commit as it is no longer necessary. The relevant bugs
were fixed properly in:
drm/radeon/kms: hopefully fix pll issues for real (v3)
5b40ddf888
drm/radeon/kms: add missing frac fb div flag for dce4+
9f4283f49f
This commit also broke certain ~5 Mhz modes on old arcade monitors,
so reverting this commit fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29502
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes the accounting when using 'debug_dma_dump_mappings()'
and CONFIG_DMA_API_DEBUG=y be assigned to the correct device
instead of 'fallback'.
No functional change - just cosmetic.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the TTM layer has used the DMA API to setup pages that are
TTM_PAGE_FLAG_DMA32 (look at patch titled: "ttm: Utilize the dma_addr_t
array for pages that are to in DMA32 pool."), lets use it
when programming the GART in the PCIe type cards.
This patch skips doing the pci_map_page (and pci_unmap_page) if
there is a DMA addresses passed in for that page. If the dma_address
is zero (or DMA_ERROR_CODE), then we continue on with our old
behaviour.
[v2: Fixed an indentation problem, added reviewed-by tag]
[v3: Added Acked-by Jerome]
Acked-by: Jerome Glisse <j.glisse@gmail.com>
Reviewed-by: Thomas Hellstrom <thomas@shipmail.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ian Campbell <ian.campbell@citrix.com>
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852https://bugzilla.kernel.org/show_bug.cgi?id=24462https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Makes debugging CS rejections much easier.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an important security fix because we allowed arbitrary values
to be passed to AARESOLVE_OFFSET. This also puts the right buffer address
in the register.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.
This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on 6xx/7xx endian fixes from Cédric Cano.
v2: fix typo in shader
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The colorbuffer, zbuffer, and texture states are checked only once when
they get changed. This improves performance in the apps which emit
lots of draw packets and few state changes.
This drops performance in glxgears by a 1% or so, but glxgears is not
a benchmark we care about.
The time spent in the kernel when running Torcs dropped from 33% to 23%
and the frame rate is higher, which is a good thing.
r600 might need something like this as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
PPC Mac cards do not provide connector tables in
their vbios. Their connector/encoder configurations
must be hardcoded in the driver.
verified by nyef on #radeon
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/mkregtable.c:parser_auth() almost always remembers
to fclose(file) before returning, but it misses two spots.
This is not really important since the process will exit shortly after and
thus close the file for us, but being explicit prevents static analysis
tools from complaining about leaked memory and missing fclose() calls and
it also seems to be the prefered style of the existing code to explicitly
close the file.
So, here's a patch to add the two missing fclose() calls.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code dereferenced a value, the new code just needs to pass
the ptr.
fixes an oops looking at files in debugfs.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This abstracts the pci/platform interface out a step further,
we can go further but this is far enough for now to allow USB
to be plugged in.
The drivers now just call the init code directly for their
device type.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is just an idea that might or might not be a good idea,
it basically adds two ioctls to create a dumb and map a dumb buffer
suitable for scanout. The handle can be passed to the KMS ioctls to create
a framebuffer.
It looks to me like it would be useful in the following cases:
a) in development drivers - we can always provide a shadowfb fallback.
b) libkms users - we can clean up libkms a lot and avoid linking
to libdrm_*.
c) plymouth via libkms is a lot easier.
Userspace bits would be just calls + mmaps. We could probably
mark these handles somehow as not being suitable for acceleartion
so as top stop people who are dumber than dumb.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We previously used a static array, but some new systems
had more states then we had array space, so dynamically
allocate space based on the number of states in the vbios.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33851
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The accelerate mode bit gets checked by certain atom
command tables to set up some register state. It needs
to be clear when setting modes and set when not.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=26942
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adds new packet to disable DX9 constant emulation.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on the vbios code. This should hopefully
fix the pll problems on a number of avivo asics
once it's enabled.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some fixes to the thermal sensor code:
- handle negative numbers
- properly handle temp calculation on different asics
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This error is reported by cppcheck:
drivers/gpu/drm/radeon/radeon_encoders.c:1066: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv50: fix regression on IGPs
drm/radeon/kms: re-emit full context state for evergreen blits
drm/radeon/kms: release CMASK access in preclose_kms
drm/radeon/kms: fix r6xx+ scanout on BE systems
drm/radeon/kms: clean up some magic numbers
drm/radeon/kms: only enable HDMI mode if radeon audio is enabled
radeon/kms: fix dp displayport mode validation
drm/nvc0/grctx: correct an off-by-one
drm/nv50: Fix race with PFIFO during PGRAPH context destruction.
drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.
drm/nvc0: implement irq handler for whatever's at 0x14xxxx
drm/nvc0: fix incorrect TPC register setup
drm/nouveau: probe for adt7473 before f75375
drm/nouveau: remove dead function definition
clear state doesn't seem to work properly in some cases
Fixes hangs in heavy 3D on some evergreen cards reported on
IRC.
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=33381
possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
We pass in the array of ttm pages to be populated in the GART/MM
of the card (or AGP). Patch titled: "ttm: Utilize the DMA API for
pages that have TTM_PAGE_FLAG_DMA32 set." uses the DMA API to make
those pages have a proper DMA addresses (in the situation where
page_to_phys or virt_to_phys do not give use the DMA (bus) address).
Since we are using the DMA API on those pages, we should pass in the
DMA address to this function so it can save it in its proper fields
(later patches use it).
[v2: Added reviewed-by tag]
Reviewed-by: Thomas Hellstrom <thellstrom@shipmail.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ian Campbell <ian.campbell@citrix.com>
R6xx+ have per-block swappers. BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Force DVI mode if the user specifies radeon.audio=0. The driver
doesn't handle HDMI mode properly in some cases.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=27731
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Check if there is a big enough dp clock & enough dp lane to
drive the video mode provided.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-By: Alex Deucher <alexdeucher@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't reset if the engine isn't busy. This matches the behavior of
previous asics. Reseting a non-hung block can lead to a hang.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Seems some other boards do this as well.
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
I'm amazed but not really surprised this worked on x86...
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
First, we were calling mc_stop() at the top of the function
which turns off all MC (memory controller) clients,
then checking if the GPU is idle. If it was idle we
returned without re-enabling the MC clients which would
lead to a blank screen, etc. This patch checks if the
GPU is idle before calling mc_stop().
Second, if the reset failed, we were returning without
re-enabling the MC clients. This patch re-enables
the MC clients before returning regardless of whether
the reset was successful or not.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching to pcie gen2 causes problems on some
boards. Add a module option to turn it on/off.
There are gen2 compatability issues with some
motherboards it seems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33027
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit dfe63bb0ad.
This commit was causing nouveau not to work properly, for -rc1 I'd
prefer it worked and we can look if this is useful for 2.6.39.
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lots of HDMI TVs overscan the incoming image by default.
The underscan option was added as a way to compensate for
that by underscanning the image so that the edges would
not be cut off on an overscanning TV. However, the TV
provides no way of knowing whether it is overscanning or
not. If the user has disabled overscan on their TV or has a
TV that does not overscan, you will get black bars around the
edges of your screen. Prior to the patch we got complaints
and bug reports from users with overscanning TVs, now with
the patch, we get lots of complaints and bug reports from
users with non-overscanning TVs. There's no good default,
but on average there have been more users complaining about
it being on by default than off, so change it to off. This
will probably result in a new deluge of overscanning TV user
complaints. There's no winning.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-ni' of ../drm-radeon-next: (30 commits)
radeon: consolidate asic-specific function decls for pre-r600
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
drm/radeon/kms: parse DCE5 encoder caps when setting up encoders
drm/radeon/kms: dvo dpms updates for DCE5
drm/radeon/kms: dac dpms updates for DCE5
drm/radeon/kms: DCE5 atom dig encoder updates
drm/radeon/kms: DCE5 atom transmitter control updates
...
Move them to radeon_asic.h together with the other asic
specific stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios only partially initializes the memory controller on
NI, so now we need to load the MC ucode in the driver and set
the default clocks once the ucode is loaded.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hardware supports advanced user defined color management
but at the moment, there is no infrastructure in place to take
advantage of it so for now we just support the legacy LUTs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some new NI (northern islands) specific display
register defines.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems disable the vbios on secondary cards or cards that
have been posted. This code re-enabled the vbios so the driver
can load it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If you change the color depth via fbset or some other framebuffer aware
userland application struct fb_fix_screeninfo is not updated to this new
information. This patch fixes this issue. Also the function is changed to
just pass in struct drm_framebuffer so in the future we could use more
fields. I'm hoping some day fix->smem* could be set here :-)
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With cmwq, there's no reason for radeon to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.
Because radeon_driver_irq_uninstall_kms() may be called from
unsleepable context, the work items can't be flushed from there.
Instead, init and flush from radeon_irq_kms_init/fini().
While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work.
Always initialize and sync cancel instead of being unnecessarily smart
about it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CMASK RAM is for colorbuffer compression (used in conjunction
with MSAA). Only one user (filp) can access it.
The CMASK RAM access is managed in the same way as Hyper-Z, but there is
a separate ioctl, because an app that uses MSAA does not necessarily
have to use zbuffering.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acer laptop (TravelMate 5730G) has an HDMI connector
on the laptop and a DVI connector on the docking station
and both share the same encoder, hpd pin, and ddc line.
The bios connector table reflects this and is technically
correct, however, we drop the DVI connector here since
xrandr has no concept of encoders (only crtcs and connectors)
and will try and drive both connectors with different crtcs
which isn't possible on the hardware side and leaves no crtcs
for LVDS or VGA.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=32732
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* 'intel/drm-intel-next' of /ssd/git/drm-next: (771 commits)
drm/i915: Undo "Uncouple render/power ctx before suspending"
drm/i915: Allow the application to choose the constant addressing mode
drm/i915: dynamic render p-state support for Sandy Bridge
drm/i915: Enable EI mode for RCx decision making on Sandybridge
drm/i915/sdvo: Border and stall select became test bits in gen5
drm/i915: Add Guess-o-matic for pageflip timestamping.
drm/i915: Add support for precise vblank timestamping (v2)
drm/i915: Add frame buffer compression on Sandybridge
drm/i915: Add self-refresh support on Sandybridge
drm/i915: Wait for vblank before unpinning old fb
Revert "drm/i915: Avoid using PIPE_CONTROL on Ironlake"
drm/i915: Pass clock limits down to PLL matcher
drm/i915: Poll for seqno completion if IRQ is disabled
drm/i915/ringbuffer: Make IRQ refcnting atomic
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915: Enable RC6 autodownclocking on Sandybridge
drm/i915: Terminate the FORCE WAKE after we have finished reading
drm/i915/gtt: Clear the cachelines upon resume
drm/i915: Restore GTT mapping first upon resume
...
Blitting from vram to gart is problematic at the moment.
Use the CPU for now to avoid buffer corruption.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This block may contain various additional LCD info such
as physical size and a stored EDID.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems have the LCD width and height in mm available in the
LCD info table. Use this info if there is no EDID to provide it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Readability cleanup and fix debugging output, no
functional change.
Reported-by: Frank Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Works more like DCE4.0 despite what the docs say.
This fixes blank screen issues when changing crtc
routing due to incorrect crtc to dig mapping.
v2: only two DIGx blocks, routing is hardcoded
based on link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
add to the 2.8 bump for pageflip
The purpose of these regs is to work around a TX hw bug in R520.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes module reloading and resume as the gfx block seems to
be left in a bad state in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For the fbdev api if the struct fb_var_screeninfo accel_flags field is set
to FB_ACCELF_TEXT then userland applications can not mmap the mmio region.
Since it is a bad idea for DRM drivers to expose the mmio region via the
fbdev layer we always set the accel_flags to prevent this. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without this, we attempt the handover too late, the firmware fb
might be accessing the chip simultaneously to us re-initializing
various parts of it, which might frighten babies or cause all sort
of nasty psychologic trauma to kitten.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[danvet: add cc: stable, forward ported and compile-fixed for X86]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[airlied: move to even earlier in module load.]
Signed-off-by: Dave Airlie <airlied@redhat.com>
this adds a bo create, and fence seq tracking tracepoints.
This is just an initial set to play around with, we should investigate
what others we need would be useful.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure vram changes hit memory. This mirrors the
6xx/7xx behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are too many strange corner cases triggered in old userspace
drivers out there to that it's nearly impossible to not break some
obscure app.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems to cause problems on certain laptops
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It should be required for all 7xx asics, but seems to cause
problems on some AGP 7xx chips.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=19002
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reported-and-Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Avoid overflowing a 32 bit value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Forbid allocating buffer bigger than visible VRAM or GTT, also
properly set lpfn field.
v2 - use max macro
- silence warning
v3 - don't explicitly set range limit
- use min macro
Cc: stable <stable@kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-fusion' of ../drm-radeon-next:
drm/radeon/kms: add Ontario APU ucode loading support
drm/radeon/kms: add Ontario Fusion APU pci ids
drm/radeon/kms: enable MSIs on fusion APUs
drm/radeon/kms: add power table parsing support for Ontario fusion APUs
drm/radeon/kms: refactor atombios power state fetching
drm/radeon/kms: add bo blit support for Ontario fusion APUs
drm/radeon/kms: add thermal sensor support for fusion APUs
drm/radeon/kms: fill in GPU init for AMD Ontario Fusion APUs
drm/radeon/kms: add radeon_asic struct for AMD Ontario fusion APUs
drm/radeon/kms: evergreen.c updates for fusion
drm/radeon/kms: MC setup changes for fusion APUs
drm/radeon/kms: move r7xx/evergreen to its own vram_gtt setup function
drm/radeon/kms: add support for ss overrides on Fusion APUs
drm/radeon/kms: Add support for external encoders on fusion APUs
drm/radeon/kms: atom changes for DCE4.1 devices
drm/radeon/kms: add new family id for AMD Ontario APUs
drm/radeon/kms: upstream power table updates
drm/radeon/kms: upstream atombios.h updates
drm/radeon/kms: upstream ObjectID.h updates
drm/radeon/kms: setup mc chremap properly on r7xx/evergreen
* 'drm-radeon-next' of ../drm-radeon-next:
drm/radeon/kms: improve pflip precision on r1xx-r4xx
drm/kms/radeon: Use high precision timestamps for pageflip completion events.
drm/kms/radeon: Reorder vblank and pageflip interrupt handling.
drm/radeon/kms: add pageflip ioctl support (v3)
drm/kms/radeon: Add support for precise vblank timestamping.
6xx/7xx was hitting the wrong BUS_CNTL reg and bits.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The update pending bit has a separate enable bit.
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit d33ef52d9d.
This change seems to expose a bug in the 3D driver tiggered by
certain apps, so revert it to keep userspace working.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios power tables on my inagua board seem a bit funky...
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The function was getting too large. Rework it to share
more state better handle new power table formats.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- CONFIG_MEMSIZE is in bytes on fusion.
- FB_BASE and FB_TOP are finer grained.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
MC_VM_FB_LOCATION is at a different offset between r6xx and r7xx/evergreen.
The location is needed for vram setup on fusion chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
System specific spread spectrum overrides can be specified in
the integrated system info table for Fusion APUs. This adds
support for using those overrides.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Should improve performance slightly and possibly fix some
issues.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than re-implementing in the Radeon driver,
Use the execbuf / cs / pushbuf utilities that comes with TTM.
This comes with an even greater benefit now that many spinlocks have been
optimized away...
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The bo lock used only to protect the bo sync object members, and since it
is a per bo lock, fencing a buffer list will see a lot of locks and unlocks.
Replace it with a per-device lock that protects the sync object members on
*all* bos. Reading and setting these members will always be very quick, so
the risc of heavy lock contention is microscopic. Note that waiting for
sync objects will always take place outside of this lock.
The bo device fence lock will eventually be replaced with a seqlock /
rcu mechanism so we can determine that a bo is idle under a
rcu / read seqlock.
However this change will allow us to batch fencing and unreserving of
buffers with a minimal amount of locking.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I had removed this when I switched the atom indirect io methods
to use the io bar rather than the mmio bar, but it appears it's
still needed.
Reported-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the vblank irq handler, calls to actual vblank handling,
or at least drm_handle_vblank(), need to happen before
calls to radeon_crtc_handle_flip().
Reason: The high precision pageflip timestamping
and some other pageflip optimizations will need the updated
vblank count and timestamps for the current vblank interval.
These are calculated in drm_handle_vblank(), therefore it
must go first.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for dri2 pageflipping.
v2: precision updates from Mario Kleiner.
v3: Multihead fixes from Mario Kleiner; missing crtc offset
add note about update pending bit on pre-avivo chips
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work and is shared across drivers.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The function is also used by the dynamic gpu reclocking
code to determine when it is safe to reclock inside vblank.
For that purpose radeon_pm_in_vbl() is modified to
accomodate a small change in the function prototype of
the radeon_get_crtc_scanoutpos() which is hooked up to
.get_scanout_position().
This code has been tested on AVIVO hardware, a RV530
(ATI Mobility Radeon X1600) in a Intel Core-2 Duo MacBookPro
and some R600 variant (FireGL V7600) in a single cpu
AMD Athlon 64 PC.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As per advice from Jean Delvare.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations. It does not contain the bank info. Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This causes the connector to not be added since i2c init fails
for the adapter. Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31688
Noticed by Ari Savolainen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Ari Savolainen <ari.m.savolainen@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle all the various asic family specific things for DVO.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.
v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP. Return something sane instead based on
the encoder id. This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like a typo in:
drm/radeon/r600: fix tiling issues in CS checker.
(f30df2fad0)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If ttm_bo_init() returns failure, it already destroyed the BO, so we need to
retry from scratch.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Temperature is not shifted as on newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
2b5b1d7da9583484b3a9e7e375a90ca0e8ca07c2
(drm/radeon/kms: add support for clock/data path routers)
That patch completed mux support for ddc and cd line routing
between connectors. This patch fixes an indexing typo that was
resulting in the atom bios router objects not always being walked,
ensures the validity entries for the reused router structure are
reset for every connector object walked, and corrects the masking
operations used to update the mux control bits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Tyson Whitehead <twhitehead@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
26b5bc9864
(drm/radeon/kms: add support for router objects)
That patch added support for systems that use a mux to control
the ddc line routing between the connectors. This patch adds
support for systems that use a mux to control the encoder
clock and data path routing to the connectors.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The A/B links aren't independantly useable on these blocks so when
we disable the encoders, make sure to only disable the encoder when
there is no connector using it.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=18564
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make more of the connector code debug only to avoid
spamming the kernel logs with detect and add modes
messages.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: enable unmappable vram for evergreen
drm/radeon/kms: fix tiled db height calculation on 6xx/7xx
drm/radeon/kms: fix handling of tex lookup disable in cs checker on r2xx
Evergreen now has blit support, but unmappable vram support
was disabled in c919b371cb
(drm/radeon/kms: avoid corner case issue with unmappable vram V2)
due to merge ordering. This re-enables unmappable vram on
evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Calculate height based on the slice bitfield rather than the size.
Same as Dave's CB fix.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are cases when multiple texture units have to be enabled,
but not actually used to sample. This patch checks to see if
the lookup_disable bit is set and if so, skips the texture check.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=25544
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (476 commits)
vmwgfx: Implement a proper GMR eviction mechanism
drm/radeon/kms: fix r6xx/7xx 1D tiling CS checker v2
drm/radeon/kms: properly compute group_size on 6xx/7xx
drm/radeon/kms: fix 2D tile height alignment in the r600 CS checker
drm/radeon/kms/evergreen: set the clear state to the blit state
drm/radeon/kms: don't poll dac load detect.
gpu: Add Intel GMA500(Poulsbo) Stub Driver
drm/radeon/kms: MC vram map needs to be >= pci aperture size
drm/radeon/kms: implement display watermark support for evergreen
drm/radeon/kms/evergreen: add some additional safe regs v2
drm/radeon/r600: fix tiling issues in CS checker.
drm/i915: Move gpu_write_list to per-ring
drm/i915: Invalidate the to-ring, flush the old-ring when updating domains
drm/i915/ringbuffer: Write the value passed in to the tail register
agp/intel: Restore valid PTE bit for Sandybridge after bdd3072
drm/i915: Fix flushing regression from 9af90d19f
drm/i915/sdvo: Remove unused encoding member
i915: enable AVI infoframe for intel_hdmi.c [v4]
drm/i915: Fix current fb blocking for page flip
drm/i915: IS_IRONLAKE is synonymous with gen == 5
...
Fix up conflicts in
- drivers/gpu/drm/i915/{i915_gem.c, i915/intel_overlay.c}: due to the
new simplified stack-based kmap_atomic() interface
- drivers/gpu/drm/vmwgfx/vmwgfx_drv.c: added .llseek entry due to BKL
removal cleanups.
broken by:
drm/radeon/r600: fix tiling issues in CS checker.
v2: only apply it to 1D tiling case.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
macro tile heights are aligned to num channels, not num banks.
Noticed by Dave Airlie.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hw stores a default clear state for registers in the context
range that can be initialized when the CP is set up. Set the
blit state as the default clear state and use the CLEAR_STATE
packet to load the blit state rather than loading it from an IB.
This reduces overhead when doing bo moves using the 3D engine.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vram map in the radeon memory controller needs to be
>= the pci aperture size. Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28402
The problematic cards in the above bug have 64 MB of vram,
but the pci aperture is 128 MB and the MC vram map was only
64 MB. This can lead to hangs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Improper display watermarks can result in underflow to the display
controllers which can cause flickering or other artifacts.
This patch implements display watermark support and line buffer
allocation for evergreen asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are needed for enabling dynamic GPR allocation in the shaders
in the userspace acceleration drivers.
v2: fix typo in reg name
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CS checker had some incorrect alignment requirements for 2D surfaces,
this made rendering to mipmap levels that were 2D broken.
Also the CB height was being worked out from the BO size, this doesn't work
at all when rendering mipmap levels, instead we work out what height userspace
wanted from slice max and use that to check it fits inside the BO, however
the DDX send the wrong slice max for an unaligned buffer so we have to workaround
for that even though its a userspace bug.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
The enter argument as implemented by commit 413d45d362 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.
There is no runtime behavior change as a result of this patch.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit ff773714dd.
A generic solution is needed to save and retore the LUT information.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I see the following error message in my kernel log from time to time:
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
After investigation, it turns out that there's nothing to be afraid of
and everything works as intended. So remove the spurious log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
